| Age | Commit message (Collapse) | Author |
|---|
|
Populate the SATA node for Tegra210.
Signed-off-by: Preetham Ramchandra <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Qualcomm Centriq 2400 REP (Reference Evaluation Platform) is
an aarch64 Armv8 server platform with an ast2520 BMC.
Signed-off-by: Ken Chen <chen.kenyy@inventec.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
GPIOS7 shall be pulled low for CPLD to continue the power up sequence.
With this hogged as pull-low, the CPLD workaround can be removed in
OpenBMC.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Romulus uses ASPEED's fan tach instead of max31785:
* Pass1's max31785 is always reset by CPLD
* Pass2's max31785 is not connected
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
https://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs devicetree changes
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
* tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Switch to port 8 for CPU port
ARM: bcm2835: Add the DPI hardware to the device tree.
ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode
ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave
ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups
ARM: dts: bcm2837-rpi-3-b: add GPIO expander
ARM: dts: bcm2835: make the firmware node into a bus
ARM: dts: bcm283x: Fix probing of bcm2835-i2s
dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s
ARM: dts: bcm283x: Fix pin function of JTAG pins
|
|
This pull request brings in one last patch to add the BCM2835 DPI
controller to the device tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0e8 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Populate the ethernet@e6800000 device node to enable Ethernet interface
for R-Car M3-N (R8A77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Move "usb2_ph1" place-holder device node next to "usb2_phy0" one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add GPIO nodes to r8a77965 SoC device tree file.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add SCIF[0-5] device nodes for M3-N (r8a77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add dmac[0-2] device nodes for R-Car M3-N (r8a77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Basic support for the Gen 3 R-Car M3-N SoC.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add configuration option for the R-Car M3-N (R8A77965) SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that we have added support for pre-pended Broadcom tags with commit
11606039604c ("net: dsa: b53: Support prepended Broadcom tags") we can
switch all the Northstar Plus reference boards to use port 8 for the CPU
port. This allows us to prepare room for supporting the Flow Accelerator
2 NAPT offload, and frees up port 5 to be made fully configurable for
the modes that it supports: internal, SGMII, RGMII etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It's currently marked disabled, as it's not useful without a panel
associated with it and the GPIO pins routed to ALT2.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
|
|
"debounce-inteval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add emif node for keystone2 devices, which is used for ECC support.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
[t-kristo@ti.com: made emif enabled by default for all keystone2 devices]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a watchdog node for keystone-k2g, with the corresponding clock and
power domain handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Pull "AT91 DT for 4.17" from Alexandre Belloni:
Not much this cycle, mainly changes on the Axentia boards from Peter and
a cleanup from Bartosz:
- use 'atmel' as at24 manufacturer
- device addition and fixes for axentia boards
- fix sama5d4 pinctrl compatible
* tag 'at91-ab-4.17-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9263ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91-sama5d2_ptc_ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9g20ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9260ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for sama5d34ek
ARM: dts: at91: sama5d4: fix pinctrl compatible string
ARM: dts: at91: tse850: make the sound dai cell count explicit
ARM: dts: at91: nattis: add lvds-encoder
ARM: dts: at91: nattis: use up-to-date mtd partitions
ARM: dts: at91: tse850: use the correct compatible for the eeprom
ARM: dts: at91: nattis: use the correct compatible for the eeprom
ARM: dts: at91: sam9rl: Properly assign copyright
|
|
next/dt
Pull "mvebu dt64 for 4.17 (part 1)" from Gregory CLEMENT:
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
* tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Add apb_pclk clock for the uart nodes
arm64: dts: marvell: use reworked NAND controller driver on Armada 8K
arm64: dts: marvell: use reworked NAND controller driver on Armada 7K
ARM64: dts: marvell: armada-cp110: Add registers clock for sata node
arm64: dts: marvell: armada-8080-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-7040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-espressobin: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-db: use SPDX-License-Identifier
arm64: dts: marvell: use SPDX-License-Identifier for Armada SoCs
arm64: dts: marvell: mcbin: fix board name typo
arm64: dts: marvell: mcbin: enable uart headers
arm64: dts: marvell: add CP110 uart peripherals
ARM64: dts: marvell: armada-cp110: Add registers clock for I2C nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for SPI nodes
|
|
Pull "mvebu dt for 4.17 (part 1)" from Gregory CLEMENT:
Most of them are small fixes or cleanup.
Only the change on the clearfog will have a noticeable effect allowing
to use the i2c at an higher frequency.
* tag 'mvebu-dt-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: increase speed of i2c0 to 400kHz
arm: dts: kirkwood: fix error in #sound-dai-cells size
ARM: dts: kirkwood: Fix "debounce-interval" property misspelling
ARM: dts: armada: netgear-rn*: fix rtc node name
|
