| Age | Commit message (Collapse) | Author |
|---|
|
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5fe ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b3250 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
the skb PTP header
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It appears that Ocelot switches cannot timestamp non-PTP frames,
I tested this using the isochron program at:
https://github.com/vladimiroltean/tsn-scripts
with the result that the driver increments the ocelot_port->ts_id
counter as expected, puts it in the REW_OP, but the hardware seems to
not timestamp these packets at all, since no IRQ is emitted.
Therefore check whether we are sending PTP frames, and refuse to
populate REW_OP otherwise.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When skb_match is NULL, it means we received a PTP IRQ for a timestamp
ID that the kernel has no idea about, since there is no skb in the
timestamping queue with that timestamp ID.
This is a grave error and not something to just "continue" over.
So print a big warning in case this happens.
Also, move the check above ocelot_get_hwtimestamp(), there is no point
in reading the full 64-bit current PTP time if we're not going to do
anything with it anyway for this skb.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Fix circular dependency between sja1105 and tag_sja1105
As discussed here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocols cannot use symbols exported by switch drivers.
Eliminate the two instances of that from tag_sja1105, and that allows us
to have a working setup with modules again.
====================
Re-applying to net, this was mistakenly applied to net-next,
see first Link.
Link: https://lore.kernel.org/r/20211012114044.2526146-1-vladimir.oltean@nxp.com/
Link: https://lore.kernel.org/r/20210922143726.2431036-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Flip the sign of a return value check, thereby suppressing the following
spurious error:
port 2 failed to notify DSA_NOTIFIER_BRIDGE_LEAVE: -EOPNOTSUPP
... which is emitted when removing an unoffloaded DSA switch port from a
bridge.
Fixes: d371b7c92d19 ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012112730.3429157-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In commit 74fc4f828769 ("net: Fix offloading indirect devices dependency
on qdisc order creation"), it adds a process to trigger the callback to
setup the bo callback when the driver regists a callback.
In our current implement, we are not ready to run the callback when nfp
call the function flow_indr_dev_register, then there will be error
message as:
kernel: Oops: 0000 [#1] SMP PTI
kernel: CPU: 0 PID: 14119 Comm: kworker/0:0 Tainted: G
kernel: Workqueue: events work_for_cpu_fn
kernel: RIP: 0010:nfp_flower_indr_setup_tc_cb+0x258/0x410
kernel: RSP: 0018:ffffbc1e02c57bf8 EFLAGS: 00010286
kernel: RAX: 0000000000000000 RBX: ffff9c761fabc000 RCX: 0000000000000001
kernel: RDX: 0000000000000001 RSI: fffffffffffffff0 RDI: ffffffffc0be9ef1
kernel: RBP: ffffbc1e02c57c58 R08: ffffffffc08f33aa R09: ffff9c6db7478800
kernel: R10: 0000009c003f6e00 R11: ffffbc1e02800000 R12: ffffbc1e000d9000
kernel: R13: ffffbc1e000db428 R14: ffff9c6db7478800 R15: ffff9c761e884e80
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: fffffffffffffff0 CR3: 00000009e260a004 CR4: 00000000007706f0
kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
kernel: PKRU: 55555554
kernel: Call Trace:
kernel: ? flow_indr_dev_register+0xab/0x210
kernel: ? __cond_resched+0x15/0x30
kernel: ? kmem_cache_alloc_trace+0x44/0x4b0
kernel: ? nfp_flower_setup_tc+0x1d0/0x1d0 [nfp]
kernel: flow_indr_dev_register+0x158/0x210
kernel: ? tcf_block_unbind+0xe0/0xe0
kernel: nfp_flower_init+0x40b/0x650 [nfp]
kernel: nfp_net_pci_probe+0x25f/0x960 [nfp]
kernel: ? nfp_rtsym_read_le+0x76/0x130 [nfp]
kernel: nfp_pci_probe+0x6a9/0x820 [nfp]
kernel: local_pci_probe+0x45/0x80
So we need to call flow_indr_dev_register in app start process instead of
init stage.
Fixes: 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20211012124850.13025-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 846d6da1fcdb ("net/mlx5e: Fix division by 0 in
mlx5e_select_queue") makes mlx5e_build_nic_params assign a non-zero
initial value to priv->num_tc_x_num_ch, so that mlx5e_select_queue
doesn't fail with division by 0 if called before the first activation of
channels. However, the initialization flow of representors doesn't call
mlx5e_build_nic_params, so this bug can still happen with representors.
This commit fixes the bug by adding the missing assignment to
mlx5e_build_rep_params.
Fixes: 846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Due to current HW arch limitations, RX-FCS (scattering FCS frame field
to software) and RX-port-timestamp (improved timestamp accuracy on the
receive side) can't work together.
RX-port-timestamp is not controlled by the user and it is enabled by
default when supported by the HW/FW.
This patch sets RX-port-timestamp opposite to RX-FCS configuration.
Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Before this patch, mlx5 representors advertised the
NETIF_F_VLAN_CHALLENGED bit, this could lead to missing features when
using reps with vxlan/bridge and maybe other virtual interfaces,
when such interfaces inherit this bit and block vlan usage in their
topology.
Example:
$ip link add dev bridge type bridge
# add representor interface to the bridge
$ip link set dev pf0hpf master
$ip link add link bridge name vlan10 type vlan id 10 protocol 802.1q
Error: 8021q: VLANs not supported on device.
Reps are perfectly capable of handling vlan traffic, although they don't
implement vlan_{add,kill}_vid ndos, hence, remove
NETIF_F_VLAN_CHALLENGED advertisement.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Reported-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
|
|
Prior to this patch in case mlx5_core_destroy_cq() failed it returns
without completing all destroy operations and that leads to memory leak.
Instead, complete the destroy flow before return error.
Also move mlx5_debug_cq_remove() to the beginning of mlx5_core_destroy_cq()
to be symmetrical with mlx5_core_create_cq().
kmemleak complains on:
unreferenced object 0xc000000038625100 (size 64):
comm "ethtool", pid 28301, jiffies 4298062946 (age 785.380s)
hex dump (first 32 bytes):
60 01 48 94 00 00 00 c0 b8 05 34 c3 00 00 00 c0 `.H.......4.....
02 00 00 00 00 00 00 00 00 db 7d c1 00 00 00 c0 ..........}.....
backtrace:
[<000000009e8643cb>] add_res_tree+0xd0/0x270 [mlx5_core]
[<00000000e7cb8e6c>] mlx5_debug_cq_add+0x5c/0xc0 [mlx5_core]
[<000000002a12918f>] mlx5_core_create_cq+0x1d0/0x2d0 [mlx5_core]
[<00000000cef0a696>] mlx5e_create_cq+0x210/0x3f0 [mlx5_core]
[<000000009c642c26>] mlx5e_open_cq+0xb4/0x130 [mlx5_core]
[<0000000058dfa578>] mlx5e_ptp_open+0x7f4/0xe10 [mlx5_core]
[<0000000081839561>] mlx5e_open_channels+0x9cc/0x13e0 [mlx5_core]
[<0000000009cf05d4>] mlx5e_switch_priv_channels+0xa4/0x230
[mlx5_core]
[<0000000042bbedd8>] mlx5e_safe_switch_params+0x14c/0x300
[mlx5_core]
[<0000000004bc9db8>] set_pflag_tx_port_ts+0x9c/0x160 [mlx5_core]
[<00000000a0553443>] mlx5e_set_priv_flags+0xd0/0x1b0 [mlx5_core]
[<00000000a8f3d84b>] ethnl_set_privflags+0x234/0x2d0
[<00000000fd27f27c>] genl_family_rcv_msg_doit+0x108/0x1d0
[<00000000f495e2bb>] genl_family_rcv_msg+0xe4/0x1f0
[<00000000646c5c2c>] genl_rcv_msg+0x78/0x120
[<00000000d53e384e>] netlink_rcv_skb+0x74/0x1a0
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Valentine Fatiev <valentinef@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Do not allow configurations of MQPRIO channel mode that do not
fully define and utilize the channels txqs.
Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, bridge cleanup is calling to cancel_delayed_work(). When this
function is finished, there is a chance that the delayed work is still
running. Also, the delayed work is queueing itself.
As a result, we might execute the delayed work after the bridge cleanup
have finished and hit a null-ptr oops[1].
Fix it by using cancel_delayed_work_sync(), which is waiting until the
work is done and will cancel the queue work.
[1]
[ 8202.143043 ] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 8202.144438 ] #PF: supervisor write access in kernel mode
[ 8202.145476 ] #PF: error_code(0x0002) - not-present page
[ 8202.146520 ] PGD 0 P4D 0
[ 8202.147126 ] Oops: 0002 [#1] SMP NOPTI
[ 8202.147899 ] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.14.0-rc6_for_upstream_min_debug_2021_08_25_16_06 #1
[ 8202.149741 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 8202.151908 ] RIP: 0010:_raw_spin_lock+0xc/0x20
[ 8202.156234 ] RSP: 0018:ffff88846f885ea0 EFLAGS: 00010046
[ 8202.157289 ] RAX: 0000000000000000 RBX: ffff88846f880000 RCX: 0000000000000000
[ 8202.158731 ] RDX: 0000000000000001 RSI: ffff8881004000c8 RDI: 0000000000000000
[ 8202.160177 ] RBP: ffff8881fe684978 R08: ffff888100140000 R09: ffffffff824455b8
[ 8202.161569 ] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
[ 8202.163004 ] R13: 0000000000000012 R14: 0000000000000200 R15: ffff88812992d000
[ 8202.164018 ] FS: 0000000000000000(0000) GS:ffff88846f880000(0000) knlGS:0000000000000000
[ 8202.164960 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8202.165634 ] CR2: 0000000000000000 CR3: 0000000108cac004 CR4: 0000000000370ea0
[ 8202.166450 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8202.167807 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8202.168852 ] Call Trace:
[ 8202.169421 ] <IRQ>
[ 8202.169792 ] __queue_work+0xf2/0x3d0
[ 8202.170481 ] ? queue_work_node+0x40/0x40
[ 8202.171270 ] call_timer_fn+0x2b/0x100
[ 8202.171932 ] __run_timers.part.0+0x152/0x220
[ 8202.172717 ] ? __hrtimer_run_queues+0x171/0x290
[ 8202.173526 ] ? kvm_clock_get_cycles+0xd/0x10
[ 8202.174232 ] ? ktime_get+0x35/0x90
[ 8202.174943 ] run_timer_softirq+0x26/0x50
[ 8202.175745 ] __do_softirq+0xc7/0x271
[ 8202.176373 ] irq_exit_rcu+0x93/0xb0
[ 8202.176983 ] sysvec_apic_timer_interrupt+0x72/0x90
[ 8202.177755 ] </IRQ>
[ 8202.178245 ] asm_sysvec_apic_timer_interrupt+0x12/0x20
Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The device advertises 8 formats, but only a rate of 48kHz is honored
by the hardware and 24 bits give chopped audio, so only report the
one working combination. This fixes out-of-the-box audio experience
with PipeWire which otherwise attempts to choose S24_3LE (while
PulseAudio defaulted to S16_LE).
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012200906.3492-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix CMA gigantic page order for 16K/64K page sizes
- Fix section mismatch error in drivers/acpi/arm64/gtdt.c
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
acpi/arm64: fix next_platform_timer() section mismatch error
arm64/hugetlb: fix CMA gigantic page order for non-4K PAGE_SIZE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A second (small) set of pdx86 bug-fixes and new hardware ids for 5.15"
* tag 'platform-drivers-x86-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int1092: Fix non sequential device mode handling
platform/x86: intel_skl_int3472: Correct null check
platform/x86: gigabyte-wmi: add support for B550 AORUS ELITE AX V2
platform/x86: amd-pmc: Add alternative acpi id for PMC controller
platform/x86: intel_scu_ipc: Update timeout value in comment
platform/x86: intel_scu_ipc: Increase virtual timeout to 10s
platform/x86: intel_scu_ipc: Fix busy loop expiry time
platform/x86: dell: Make DELL_WMI_PRIVACY depend on DELL_WMI
platform/mellanox: mlxreg-io: Fix read access of n-bytes size attributes
platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() call
|
|
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes: a712c3ed9b8a ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5ed ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449be ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush")
added a lock around the Tx timestamp tracker flow which is used to
cleanup any left over SKBs and prepare for device removal.
This lock is problematic because it is being held around a call to
ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY
write command to firmware. This could lead to a deadlock if the mutex
actually sleeps, and causes the following warning on a kernel with
preemption debugging enabled:
[ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573
[ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod
[ 715.435652] INFO: lockdep is turned off.
[ 715.439591] Preemption disabled at:
[ 715.439594] [<0000000000000000>] 0x0
[ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c
[ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020
[ 715.468483] Call Trace:
[ 715.470940] dump_stack_lvl+0x6a/0x9a
[ 715.474613] ___might_sleep.cold+0x224/0x26a
[ 715.478895] __mutex_lock+0xb3/0x1440
[ 715.482569] ? stack_depot_save+0x378/0x500
[ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.494979] ? kfree+0xc1/0x520
[ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0
[ 715.502837] ? kasan_set_free_info+0x20/0x30
[ 715.507110] ? __kasan_slab_free+0x10b/0x140
[ 715.511385] ? slab_free_freelist_hook+0xc7/0x220
[ 715.516092] ? kfree+0xc1/0x520
[ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.535133] ? pci_device_remove+0xab/0x1d0
[ 715.539318] ? __device_release_driver+0x35b/0x690
[ 715.544110] ? driver_detach+0x214/0x2f0
[ 715.548035] ? bus_remove_driver+0x11d/0x2f0
[ 715.552309] ? pci_unregister_driver+0x26/0x250
[ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.570554] ? do_syscall_64+0x3b/0x90
[ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.579529] ? start_flush_work+0x542/0x8f0
[ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.599960] ? wait_for_completion_io+0x250/0x250
[ 715.604662] ? lock_acquire+0x196/0x200
[ 715.608504] ? do_raw_spin_trylock+0xa5/0x160
[ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0
[ 715.633550] ? trace_hardirqs_on+0x1c/0x130
[ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.646220] ? do_raw_spin_trylock+0xa5/0x160
[ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73
[ 715.696005] pci_device_remove+0xab/0x1d0
[ 715.700018] __device_release_driver+0x35b/0x690
[ 715.704637] driver_detach+0x214/0x2f0
[ 715.708389] bus_remove_driver+0x11d/0x2f0
[ 715.712489] pci_unregister_driver+0x26/0x250
[ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.730210] ? free_module+0x6d0/0x6d0
[ 715.733963] ? task_work_run+0xe1/0x170
[ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0
[ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80
[ 715.747215] ? trace_hardirqs_on+0x1c/0x130
[ 715.751401] do_syscall_64+0x3b/0x90
[ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.760033] RIP: 0033:0x7f4dfe59000b
[ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48
[ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b
[ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918
[ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940
[ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0
Notice that this is the only case where we use the lock in this way. In
the cleanup kthread and work kthread the lock is only taken around the
bit accesses. This was done intentionally to avoid this kind of issue.
The way the lock is used, we only protect ordering of bit sets vs bit
clears. The Tx writers in the hot path don't need to be protected
against the entire kthread loop. The Tx queues threads only need to
ensure that they do not re-use an index that is currently in use. The
cleanup loop does not need to block all new set bits, since it will
re-queue itself if new timestamps are present.
Fix the tracker flow so that it uses the same flow as the standard
cleanup thread. In addition, ensure the in_use bitmap actually gets
cleared properly.
This fixes the warning and also avoids the potential deadlock that might
have occurred otherwise.
Fixes: 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Justin Iurman says:
====================
Correct the IOAM behavior for undefined trace type bits
(@Jakub @David: there will be a conflict for #2 when merging net->net-next, due
to commit [1]. The conflict is only 5-10 lines for #2 (#1 should be fine) inside
the file tools/testing/selftests/net/ioam6.sh, so quite short though possibly
ugly. Sorry for that, I didn't expect to post this one... Had I known, I'd have
made the opposite.)
Modify both the input and output behaviors regarding the trace type when one of
the undefined bits is set. The goal is to keep the interoperability when new
fields (aka new bits inside the range 12-21) will be defined.
The draft [2] says the following:
---------------------------------------------------------------
"Bit 12-21 Undefined. These values are available for future
assignment in the IOAM Trace-Type Registry (Section 8.2).
Every future node data field corresponding to one of
these bits MUST be 4-octets long. An IOAM encapsulating
node MUST set the value of each undefined bit to 0. If
an IOAM transit node receives a packet with one or more
of these bits set to 1, it MUST either:
1. Add corresponding node data filled with the reserved
value 0xFFFFFFFF, after the node data fields for the
IOAM-Trace-Type bits defined above, such that the
total node data added by this node in units of
4-octets is equal to NodeLen, or
2. Not add any node data fields to the packet, even for
the IOAM-Trace-Type bits defined above."
---------------------------------------------------------------
The output behavior has been modified to respect the fact that "an IOAM encap
node MUST set the value of each undefined bit to 0" (i.e., undefined bits can't
be set anymore).
As for the input behavior, current implementation is based on the second choice
(i.e., "not add any data fields to the packet [...]"). With this solution, any
interoperability is lost (i.e., if a new bit is defined, then an "old" kernel
implementation wouldn't fill IOAM data when such new bit is set inside the trace
type).
The input behavior is therefore relaxed and these undefined bits are now allowed
to be set. It is only possible thanks to the sentence "every future node data
field corresponding to one of these bits MUST be 4-octets long". Indeed, the
default empty value (the one for 4-octet fields) is inserted whenever an
undefined bit is set.
[1] cfbe9b002109621bf9a282a4a24f9415ef14b57b
[2] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The output behavior for undefined bits is now directly tested inside the bash
script. Trying to set an undefined bit should be refused.
The input behavior for undefined bits has been removed due to the fact that we
would need another sender allowed to set undefined bits.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for undefined bits in the trace type is moved from the input side to
the output side, while the input side is relaxed and now inserts default empty
values when an undefined bit is set.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1ba3 ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a2a1 ("r8152: support request_firmware for RTL8153")
Fixes: ac718b69301c7 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7ac (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument
to & or |
These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here.
Here should be DEV_CLOCK_CFG_MAC_RX_RST.
Fixes: e6e12df625f2 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Then name of this protocol changed in commit 94531cfcbe79 ("af_unix: Add
unix_stream_proto for sockmap") because that commit added stream support
to the af_unix protocol. Renaming the existing protocol makes a ChromeOS
protocol test[1] fail now that the name has changed in
/proc/net/protocols from "UNIX" to "UNIX-DGRAM".
Let's put the name back to how it was while keeping the stream protocol
as "UNIX-STREAM" so that the procfs interface doesn't change. This fixes
the test and maintains backwards compatibility in proc.
Cc: Jiang Wang <jiang.wang@bytedance.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/tast-tests/src/chromiumos/tast/local/bundles/cros/network/supported_protocols.go;l=50;drc=e8b1c3f94cb40a054f4aa1ef1aff61e75dc38f18 [1]
Fixes: 94531cfcbe79 ("af_unix: Add unix_stream_proto for sockmap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kunit fixes from Shuah Khan:
- Fixes to address the structleak plugin causing the stack frame size
to grow immensely when used with KUnit. Fixes include adding a new
makefile to disable structleak and using it from KUnit iio, device
property, thunderbolt, and bitfield tests to disable it.
- KUnit framework reference count leak in kfree_at_end
- KUnit tool fix to resolve conflict between --json and --raw_output
and generate correct test output in either case.
- kernel-doc warnings due to mismatched arg names
* tag 'linux-kselftest-kunit-fixes-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kernel-doc warnings due to mismatched arg names
bitfield: build kunit tests without structleak plugin
thunderbolt: build kunit tests without structleak plugin
device property: build kunit tests without structleak plugin
iio/test-format: build kunit tests without structleak plugin
gcc-plugins/structleak: add makefile var for disabling structleak
kunit: fix reference count leak in kfree_at_end
kunit: tool: better handling of quasi-bool args (--json, --raw_output)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"All documentation / comment updates"
* 'for-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroupv2, docs: fix misinformation in "device controller" section
cgroup/cpuset: Change references of cpuset_mutex to cpuset_rwsem
docs/cgroup: remove some duplicate words
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"One patch to add a missing __printf annotation and the other to enable
deferred printing for debug dumps to avoid deadlocks when triggered
from some contexts (e.g. console drivers)"
* 'for-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix state-dump console deadlock
workqueue: annotate alloc_workqueue() as printf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more error handling fixes, stemming from code inspection, error
injection or fuzzing"
* tag 'for-5.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix abort logic in btrfs_replace_file_extents
btrfs: check for error when looking up inode during dir entry replay
btrfs: unify lookup return value when dir entry is missing
btrfs: deal with errors when adding inode reference during log replay
btrfs: deal with errors when replaying dir entry during log replay
btrfs: deal with errors when checking if a dir entry exists during log replay
btrfs: update refs for any root except tree log roots
btrfs: unlock newly allocated extent buffer after error
|
|
Add a test case that demonstrates port shadowing via UDP.
ns2 sends packet to ns1, from source port used by a udp service on the
router, ns0. Then, ns1 sends packet to ns0:service, but that ends up getting
forwarded to ns2.
Also add three test cases that demonstrate mitigations:
1. disable use of $port as source from 'unstrusted' origin
2. make the service untracked. This prevents masquerade entries
from having any effects.
3. add forced PAT via 'random' mode to translate the "wrong" sport
into an acceptable range.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
For non-4K PAGE_SIZE configs, the largest gigantic huge page size is
CONT_PMD_SHIFT order. On arm64 with 64K PAGE_SIZE, the gigantic page is
16G. Therefore, one should be able to specify 'hugetlb_cma=16G' on the
kernel command line so that one gigantic page can be allocated from CMA.
However, when adding such an option the following message is produced:
hugetlb_cma: cma area should be at least 8796093022208 MiB
This is because the calculation for non-4K gigantic page order is
incorrect in the arm64 specific routine arm64_hugetlb_cma_reserve().
Fixes: abb7962adc80 ("arm64/hugetlb: Reserve CMA areas for gigantic pages on 16K and 64K configs")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20211005202529.213812-1-mike.kravetz@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Console drivers often queue work while holding locks also taken in their
console write paths, something which can lead to deadlocks on SMP when
dumping workqueue state (e.g. sysrq-t or on suspend failures).
For serial console drivers this could look like:
CPU0 CPU1
---- ----
show_workqueue_state();
lock(&pool->lock); <IRQ>
lock(&port->lock);
schedule_work();
lock(&pool->lock);
printk();
lock(console_owner);
lock(&port->lock);
where workqueues are, for example, used to push data to the line
discipline, process break signals and handle modem-status changes. Line
disciplines and serdev drivers can also queue work on write-wakeup
notifications, etc.
Reworking every console driver to avoid queuing work while holding locks
also taken in their write paths would complicate drivers and is neither
desirable or feasible.
Instead use the deferred-printk mechanism to avoid printing while
holding pool locks when dumping workqueue state.
Note that there are a few WARN_ON() assertions in the workqueue code
which could potentially also trigger a deadlock. Hopefully the ongoing
printk rework will provide a general solution for this eventually.
This was originally reported after a lockdep splat when executing
sysrq-t with the imx serial driver.
Fixes: 3494fc30846d ("workqueue: dump workqueues on sysrq-t")
Cc: stable@vger.kernel.org # 4.0
Reported-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Michael Forney reported an incorrect padding type that was defined in
the commit 80fe7430c708 ("ALSA: add new 32-bit layout for
snd_pcm_mmap_status/control") for PCM control mmap data.
His analysis is correct, and this caused the misplacements of PCM
control data on 32bit arch and 32bit compat mode.
The bug is that the __pad2 definition in __snd_pcm_mmap_control64
struct was wrongly with __pad_before_uframe, which should have been
__pad_after_uframe instead. This struct is used in SYNC_PTR ioctl and
control mmap. Basically this bug leads to two problems:
- The offset of avail_min field becomes wrong, it's placed right after
appl_ptr without padding on little-endian
- When appl_ptr and avail_min are read as 64bit values in kernel side,
the values become either zero or corrupted (mixed up)
One good news is that, because both user-space and kernel
misunderstand the wrong offset, at least, 32bit application running on
32bit kernel works as is. Also, 64bit applications are unaffected
because the padding size is zero. The remaining problem is the 32bit
compat mode; as mentioned in the above, avail_min is placed right
after appl_ptr on little-endian archs, 64bit kernel reads bogus values
for appl_ptr updates, which may lead to streaming bugs like jumping,
XRUN or whatever unexpected.
(However, we haven't heard any serious bug reports due to this over
years, so practically seen, it's fairly safe to assume that the impact
by this bug is limited.)
Ideally speaking, we should correct the wrong mmap status control
definition. But this would cause again incompatibility with the
existing binaries, and fixing it (e.g. by renumbering ioctls) would be
really messy.
So, as of this patch, we only correct the behavior of 32bit compat
mode and keep the rest as is. Namely, the SYNC_PTR ioctl is now
handled differently in compat mode to read/write the 32bit values at
the right offsets. The control mmap of 32bit apps on 64bit kernels
has been already disabled (which is likely rather an overlook, but
this worked fine at this time :), so covering SYNC_PTR ioctl should
suffice as a fallback.
Fixes: 80fe7430c708 ("ALSA: add new 32-bit layout for snd_pcm_mmap_status/control")
Reported-by: Michael Forney <mforney@mforney.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/29QBMJU8DE71E.2YZSH8IHT5HMH@mforney.org
Link: https://lore.kernel.org/r/20211010075546.23220-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
SAR information from BIOS may come in non sequential pattern.
To overcome the issue, a check is made to extract the right SAR
information using the device mode which is currently being used.
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Shravan S <s.shravan@intel.com>
Link: https://lore.kernel.org/r/20211006073525.1332925-1-s.shravan@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
The int3472-discrete driver can enter an error path after initialising
int3472->clock.ena_gpio, but before it has registered the clock. This will
cause a NULL pointer dereference, because clkdev_drop() is not null aware.
Instead of guarding the call to skl_int3472_unregister_clock() by checking
for .ena_gpio, check specifically for the presence of the clk_lookup, which
will guarantee clkdev_create() has already been called.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214453
Fixes: 7540599a5ef1 ("platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20211008224608.415949-1-djrscally@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This works just fine on my system.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211005044855.1429724-1-zephaniah@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Surface Laptop 4 AMD has used the AMD0005 to identify this
controller instead of using the appropriate ACPI ID AMDI0005. Include
AMD0005 in the acpi id list.
Link: https://github.com/linux-surface/acpidumps/tree/master/surface_laptop_4_amd
Link: https://gist.github.com/nakato/2a1a7df1a45fe680d7a08c583e1bf863
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Sachi King <nakato@nakato.io>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20211002041840.2058647-1-nakato@nakato.io
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") states that the recommended timeout range
is 5-10 seconds. Adjust the timeout value to the higher of those i.e 10
seconds, to account for situations where the 5 seconds is insufficient
for disconnect command success.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-3-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The macro IPC_TIMEOUT is already in jiffies (it is also used like that
elsewhere in the file when calling wait_for_completion_timeout()). Don’t
convert it using helper functions for the purposes of calculating the
busy loop expiry time.
Fixes: e7b7ab3847c9 (“platform/x86: intel_scu_ipc: Sleeping is fine when polling”)
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-2-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
DELL_WMI_PRIVACY is a feature toggle for the main dell-wmi driver,
so it must depend on the Kconfig option which enables the main
dell-wmi driver.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211011132338.407571-1-hdegoede@redhat.com
|
