| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM DT updates from Arnd Bergmann:
"As usual, the bulk of the changes for the SoC tree are devicetree file
updates, and most of these changes are for 64-bit embedded machines.
As before, there are a ton of style cleanups, and additional hardware
support for existing machines.
Looking only at the new SoC, the notable additions are:
- A whole family of Broadcom broadband SoCs, both 32-bit and 64-bit:
BCM63178, BCM63158, BCM4912, BCM6858, BCM6878, BCM6846, BCM63146,
BCM6856, BCM6855, BCM6756, BCM63148, and BCM6813. Each SoC comes
with a corresponding reference board.
- The new NXP i.MX93 SoC, the follow-up to the popular i.MX6 and
i.MX8 embedded SoCs, now using Cortex-A55 cores and the Ethos-U65
NPU.
- Qualcomm Snapdragon 8cx Gen3 (SC8280XP), the current high end of
Arm based Laptop SoCs, and its automotive cousin, the SA8540P. The
SC8280XP is used in the Lenovo Thinkpad X13s laptop that also gets
added here in addition to the reference boards.
- Allwinner H616, a newer version of the H6 SoC, targeted at
Set-top-box applications. It comes with dts files for the Orange Pi
zero2 single-board computer and the X96 Mate set-top-box
- Marvell Prestera 98DX2530 (AlleyCat5), a network switch chip in the
Armada SoC family based on the Cortex-A55 core.
New machines based on previously supported SoCs include:
- Several new machines on NXP i.MX platforms: multiple Toradex
Colibri boards using the "Iris" and "Ixora" carriers, DH
electronics i.MX8M Plus DHCOM and PDK2, TQ-Systems TQMa8MPQL, and
phytech phyBOARD-Polis-i.MX8MM.
- Google Chameleon v3 FPGA board based on Intel Arria10 and Stratix
10 Software Virtual platform, both in the SoCFPGA platform.
- Two new wireless devices based on Broadcom SoCs: The Asus GT-AX6000
Router and the Cisco Meraki MR26 access point
- Improved Chromebook support for both the Mediatek and Qualcomm SoC
families brought added machines: Acer Chromebook 514 (MT8192), Acer
Chromebook Spin 513 (MT8195) and a couple of SC7180 based machines
including the Lenovo IdeaPad Chromebook Duet 3.
- Xiaomi Mi Mix2s, LG G7 and LG V35 are mobile phones based on
Qualcomm SDM845, while Mi 5s Plus is based on MSM8996.
- Finally, there are a few development board on other chips: PCB8309
(Microchip lan966x), Radxa Rock Pi S (Rockchips RK3308) DH DRC
Compact (ST STM32MP1) and Inforce IFC6560 (Qualcomm SDM660)"
* tag 'arm-dt-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (829 commits)
dt-bindings: soc: bcm: use absolute path to other schema
dt-bindings: soc: bcm: drop quotes when not needed
dt-bindings: soc: microchip: use absolute path to other schema
dt-bindings: soc: microchip: drop quotes when not needed
ARM: dts: lan966x: keep lan966 entries alphabetically sorted
ARM: dts: lan966x: add support for pcb8309
dt-bindings: arm: at91: add lan966 pcb8309 board
ARM: dts: lan966x: Enable network driver on pcb8291
ARM: dts: lan966x: Disable can0 on pcb8291
ARM: dts: lan966x: Add gpio-restart
dt-bindings: arm: aspeed: add Aspeed Evaluation boards
arm64: dts: qcom: Add support for Xiaomi Mi Mix2s
dt-bindings: arm: qcom: Add Xiaomi Mi Mix2s bindings
dt-bindings: arm: qcom: Document lg,judyln and lg,judyp devices
dt-bindings: arm: qcom: add missing SM6350 board compatibles
dt-bindings: arm: qcom: add missing SM6125 board compatibles
dt-bindings: arm: qcom: add missing SDM845 board compatibles
dt-bindings: arm: qcom: add missing SDM636 board compatibles
dt-bindings: arm: qcom: add missing SDM630 board compatibles
dt-bindings: arm: qcom: add missing QCS404 board compatibles
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The updates for arch/arm/mach-* platform code this time are mainly
minor cleanups.
Most notably, the DaVinci DM644x/DM646x SoC support gets removed. This
was also scheduled for later removal early next year, but Linus
Walleij asked for having them removed earlier to avoid problems for
the GPIO subsystem"
* tag 'arm-soc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: at91: setup outer cache .write_sec() callback if needed
ARM: at91: add sam_linux_is_optee_available() function
ARM: Marvell: Update PCIe fixup
ARM: bcmbca: Include full family name in Kconfig
ARM: bcm: NSP: Removed forced thermal selection
ARM: debug: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
arm: bcmbca: Add BCMBCA sub platforms
arm: bcmbca: Move BCM63138 ARCH_BCM_63XX to ARCH_BCMBCA
MAINTAINERS: Move BCM63138 to bcmbca arch entry
ARM: shmobile: rcar-gen2: Increase refcount for new reference
ARM: davinci: Delete DM646x board files
ARM: davinci: Delete DM644x board files
firmware: xilinx: Add TF_A_PM_REGISTER_SGI SMC call
cpufreq: zynq: Fix refcount leak in zynq_get_revision
ARM: OMAP2+: Kconfig: Fix indentation
ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
ARM: OMAP2+: pdata-quirks: Fix refcount leak bug
ARM: OMAP2+: display: Fix refcount leak bug
ARM: OMAP2+: Fix refcount leak in omapdss_init_of
ARM: imx25: support silicon revision 1.2
...
|
|
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
When non-devm resources are allocated they mustn't be followed by
devm allocations, otherwise it will break the tear down ordering
and might lead to crashes or other bugs during ->remove() stage.
Fix this by wrapping mutex_destroy() call with
devm_add_action_or_reset().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Simplify the error handling in probe function by switching from
dev_err() to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Fix remaining non-standard place for comments.
Remove remaining dev_dbg after regmap_read in is31fl3196_brightness_set.
Remove __func__ in dev_dbg calls, instead adding "channel" string to
describe the first displayed value.
Change remaining container_of() call to be on one line,
as well as a few others.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Set specific chipset structs values for is31fl319{0,1,3}
so that those chips can actually work.
Datasheets:
https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Allow setting chips' specifics in chipdef struct by adding fields for:
- the reset register address
- a pointer to a regmap_config struct
- a pointer to a brightness_set function
- current default, min and max values
- a boolean to distinguish 319{0,1,3} and 319{6,9} chips
and use those fields in places where distinction has to be made.
The fields for 319{0,1,3} still point to 319{6,9} values.
No functional change.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
In order to add real support for is31fl3190, is31fl3191 and is31fl3193,
rename variant-dependent elements to not use 319X where needed.
3190 suffix is used for is31fl3190, is31fl3191 and is31fl3193 circuits.
3196 suffix is used for is31fl3196 and is31fl3199.
Those two groups have different register maps, current settings and even
a different interpretation of the software shutdown bit:
https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
Rename variables, structures and defines in preparation of the splitting.
No functional nor behaviour change.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Add si-en compatibles for all chip variants.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/late
SoCFPGA dts updates for v5.20, part 2
- Update EMAC AXI settings for Cyclone5
* tag 'socfpga_updates_for_v5.20_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: add EMAC AXI settings for Cyclone5
arm64: dts: altera: socfpga_stratix10: move clocks out of soc node
arm64: dts: Add support for Stratix 10 Software Virtual Platform
dt-bindings: altera: document Stratix 10 SWVP compatibles
arm64: dts: altera: adjust whitespace around '='
arm64: dts: intel: socfpga_agilex: use defined GIC interrupt type for ECC
dt-bindings: altera: Add Chameleon v3 board
ARM: dts: socfpga: Add Google Chameleon v3 devicetree
ARM: dts: socfpga: Add atsha204a node to Mercury+ AA1 dts
ARM: dts: socfpga: Move sdmmc-ecc node to Arria 10 dts
ARM: dts: socfpga: Change Mercury+ AA1 dts to dtsi
Link: https://lore.kernel.org/r/20220728223237.3184243-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces those usages
straightforwardly with a new helper, sysfs_emit().
Link: https://lore.kernel.org/r/20220801165639.26030-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces those usages
straightforwardly with new helpers, sysfs_emit() and sysfs_emit_at().
Link: https://lore.kernel.org/r/20220801165639.26030-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces such a
sprintf() call straightforwardly with the new helper.
Link: https://lore.kernel.org/r/20220801165639.26030-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sysfs_emit() is a new helper to simplify the sysfs string output.
Replace the open-code with this new helper.
Link: https://lore.kernel.org/r/20220801165639.26030-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces such sprintf()
calls with sysfs_emit() while simplifying the open code in
list_show().
Link: https://lore.kernel.org/r/20220801165639.26030-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces such sprintf()
calls with sysfs_emit() while simplifying the open code in
modalias_show(); as modalias[] is a NUL-terminated string, we can pass
it straightly to a printf() argument.
Link: https://lore.kernel.org/r/20220801165639.26030-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces the open code
straightforwardly with a new helper.
Link: https://lore.kernel.org/r/20220801165639.26030-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
arm/late
Apple SoC DT updates for 5.20.
This round just adds the NVMe controller nodes, since that driver is
finally upstream. Includes one related power domain fixup.
* tag 'asahi-soc-dt-5.20' of https://github.com/AsahiLinux/linux:
arm64: dts: apple: t8103: Add ANS2 NVMe nodes
arm64: dts: apple: Re-parent ANS2 power domains
Link: https://lore.kernel.org/r/6de8649c-9795-54a1-fa45-8dd50355061f@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Reset controller updates for v5.20
Allow reset-simple to be selected under EXPERT and reset-a10sr to be
built under COMPILE_TEST. Add Renesas RZ/G2UL USBPHY binding and a new
driver for the TI TPS380x line of voltage supervisor ICs with manual
reset control.
A patch to make reset-microchip-sparx5 buildable as a module had to be
reverted as that turned out to break MDIO on kswitch-d10.
* tag 'reset-for-v5.20' of git://git.pengutronix.de/pza/linux:
reset: tps380x: Fix spelling mistake "Voltags" -> "Voltage"
reset: tps380x: Add TPS380x device driver supprt
dt-bindings: reset: Add TPS380x documentation
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G2UL USBPHY Control bindings
reset: reset-simple should depends on HAS_IOMEM
Revert "reset: microchip-sparx5: allow building as a module"
reset: a10sr: allow building under COMPILE_TEST
reset: allow building of reset simple driver if expert config selected
reset: microchip-sparx5: allow building as a module
Link: https://lore.kernel.org/r/20220729133620.488379-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/AsahiLinux/linux into arm/fixes
Apple SoC MAINTAINERS updates for 5.20.
Just one patch adding our shiny new mailing list to the relevant
section.
* tag 'asahi-soc-maintainers-5.20' of https://github.com/AsahiLinux/linux:
MAINTAINERS: add ARM/APPLE MACHINE mailing list
Link: https://lore.kernel.org/r/308defdf-8873-63ed-dc9c-a88cd7a3cc2f@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
An interrupt for USB device are shared with USB host. Set interrupt-names
property to common "dwc_usb3" instead of "host" and "peripheral".
Cc: stable@vger.kernel.org
Fixes: d7b9beb830d7 ("arm64: dts: uniphier: Add USB3 controller nodes")
Reported-by: Ryuta NAKANISHI <nakanishi.ryuta@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
An interrupt for USB device are shared with USB host. Set interrupt-names
property to common "dwc_usb3" instead of "host" and "peripheral".
Cc: stable@vger.kernel.org
Fixes: 45be1573ad19 ("ARM: dts: uniphier: Add USB3 controller nodes")
Reported-by: Ryuta NAKANISHI <nakanishi.ryuta@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
fix follow spelling misktakes:
decendant ==> descendant
indentify ==> identify
underlaying ==> underlying
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Striding RQ uses MTT page mapping, where each page corresponds to an XSK
frame. MTT pages have alignment requirements, and XSK frames don't have
any alignment guarantees in the unaligned mode. Frames with improper
alignment must be discarded, otherwise the packet data will be written
at a wrong address.
Fixes: 282c0c798f8e ("net/mlx5e: Allow XSK frames smaller than a page")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20220729121356.3990867-1-maximmi@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 4d5c5bad5193 ("powerpc: Remove asm/prom.h from asm/mpc52xx.h
and asm/pci.h") that cleans up powerpc's asm/prom.h leads to build
errors in ppc4xx_edac.c due to missing header. Include required
header directly to avoid the build failure.
Fixes: 4d5c5bad5193 ("powerpc: Remove asm/prom.h from asm/mpc52xx.h and asm/pci.h")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/993f5a7da371458cb819b5f3f569073c78523b01.1659436180.git.christophe.leroy@csgroup.eu
|
|
The recent change to the PHB numbering logic has a logic error in the
handling of "ibm,opal-phbid".
When an "ibm,opal-phbid" property is present, &prop is written to and
ret is set to zero.
The following call to of_alias_get_id() is skipped because ret == 0.
But then the if (ret >= 0) is true, and the body of that if statement
sets prop = ret which throws away the value that was just read from
"ibm,opal-phbid".
Fix the logic by only doing the ret >= 0 check in the of_alias_get_id()
case.
Fixes: 0fe1e96fef0a ("powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias")
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220802105723.1055178-1-mpe@ellerman.id.au
|
|
be zero
It's possible that this kernel has been kexec'd from a kernel that
enabled bus lock detection, or (hypothetically) BIOS/firmware has set
DEBUGCTLMSR_BUS_LOCK_DETECT.
Disable bus lock detection explicitly if not wanted.
Fixes: ebb1064e7c2e ("x86/traps: Handle #DB for bus lock")
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20220802033206.21333-1-chenyi.qiang@intel.com
|
|
Fix kprobes to update kcb (kprobes control block) status flag to
KPROBE_HIT_SSDONE even if the kp->post_handler is not set.
This bug may cause a kernel panic if another INT3 user runs right
after kprobes because kprobe_int3_handler() misunderstands the
INT3 is kprobe's single stepping INT3.
Fixes: 6256e668b7af ("x86/kprobes: Use int3 instead of debug trap for single-step")
Reported-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Daniel Müller <deso@posteo.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20220727210136.jjgc3lpqeq42yr3m@muellerd-fedora-PC2BDTX9
Link: https://lore.kernel.org/r/165942025658.342061.12452378391879093249.stgit@devnote2
|
|
kernel_text_address() treats ftrace_trampoline, kprobe_insn_slot
and bpf_text_address as valid kprobe addresses - which is not ideal.
These text areas are removable and changeable without any notification
to kprobes, and probing on them can trigger unexpected behavior:
https://lkml.org/lkml/2022/7/26/1148
Considering that jump_label and static_call text are already
forbiden to probe, kernel_text_address() should be replaced with
core_kernel_text() and is_module_text_address() to check other text
areas which are unsafe to kprobe.
[ mingo: Rewrote the changelog. ]
Fixes: 5b485629ba0d ("kprobes, extable: Identify kprobes trampolines as kernel text area")
Fixes: 74451e66d516 ("bpf: make jited programs visible in traces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20220801033719.228248-1-chenzhongjin@huawei.com
|
|
The Anker PowerExpand USB-C to Gigabit Ethernet adapter uses this
chipset, but exposes CDC Ethernet configurations as well as the
vendor specific one. This driver tries to bind by PID:VID
unconditionally and ends up picking up the CDC configuration, which
is supposed to be handled by the class driver. To make things even
more confusing, it sees both of the CDC class interfaces and tries
to bind twice, resulting in two broken Ethernet devices.
Change all the ID matches to specifically match the vendor-specific
interface. By default the device comes up in CDC mode and is bound by
that driver (which works fine); users may switch it to the vendor
interface using sysfs to set bConfigurationValue, at which point the
device actually goes through a reconnect cycle and comes back as a
vendor specific only device, and then this driver binds and works too.
The affected device uses VID/PID 0b95:1790, but we might as well change
all of them for good measure, since there is no good reason for this
driver to bind to standard CDC Ethernet interfaces.
v3: Added VID/PID info to commit message
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20220731072209.45504-1-marcan@marcan.st
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The function ioremap() in gscps2_probe() can fail, so
its return value should be checked.
Fixes: 4bdc0d676a643 ("remove ioremap_nocache and devm_ioremap_nocache")
Cc: <stable@vger.kernel.org> # v5.6+
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The ioam6.sh test script exits with an error code (1) when tests are
skipped due to lack of support from userspace/kernel or not enough
permissions. It should return the kselftests SKIP code instead.
Reviewed-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Link: https://lore.kernel.org/r/20220801124615.256416-1-kleber.souza@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This refixes:
commit 7da17624e7948d5d9660b910f8079d26d26ce453
nt: usb: USB_RTL8153_ECM should not default to y
In general, device drivers should not be enabled by default.
which basically broke the commit it claimed to fix, ie:
commit 657bc1d10bfc23ac06d5d687ce45826c760744f9
r8153_ecm: avoid to be prior to r8152 driver
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
this commit amounted to:
drivers/net/usb/Kconfig:
+config USB_RTL8153_ECM
+ tristate "RTL8153 ECM support"
+ depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
+ default y
+ help
+ This option supports ECM mode for RTL8153 ethernet adapter, when
+ CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
+ supported by r8152 driver.
drivers/net/usb/Makefile:
-obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o r8153_ecm.o
+obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
+obj-$(CONFIG_USB_RTL8153_ECM) += r8153_ecm.o
And as can be seen it pulls a piece of the cdc_ether driver out into
a separate config option to be able to make this piece modular in case
cdc_ether is builtin, while r8152 is modular.
While in general, device drivers should indeed not be enabled by default:
this isn't a device driver per say, but rather this is support code for
the CDCETHER (ECM) driver, and should thus be enabled if it is enabled.
See also email thread at:
https://www.spinics.net/lists/netdev/msg767649.html
In:
https://www.spinics.net/lists/netdev/msg768284.html
Jakub wrote:
And when we say "removed" we can just hide it from what's prompted
to the user (whatever such internal options are called)? I believe
this way we don't bring back Marek's complaint.
Side note: these incorrect defaults will result in Android 13
on 5.15 GKI kernels lacking USB_RTL8153_ECM support while having
USB_NET_CDCETHER (luckily we also have USB_RTL8150 and USB_RTL8152,
so it's probably only an issue for very new RTL815x hardware with
no native 5.15 driver).
Fixes: 7da17624e7948d5d ("nt: usb: USB_RTL8153_ECM should not default to y")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220730230113.4138858-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fixes the coverity warning 'EVALUATION_ORDER' violation. port is written
twice with the same value.
Signed-off-by: Sebin Sebastian <mailmesebin00@gmail.com>
Link: https://lore.kernel.org/r/20220801040731.34741-1-mailmesebin00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PTP messages like SYNC, FOLLOW_UP, DELAY_REQ are of size 58 bytes.
Using a minimum packet length as 64 makes NIX to pad 6 bytes of
zeroes while transmission. This is causing latest ptp4l application to
emit errors since length in PTP header and received packet are not same.
Padding upto 3 bytes is fine but more than that makes ptp4l to assume
the pad bytes as a TLV. Hence reduce the size to 60 from 64.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20220729092457.3850-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-qcom
Pull Qualcomm clk driver updates from Bjorn Andersson:
- Introduces support for the camera clock controller in SM8450 and
the display and gpu clock controllers in SM8350.
- Various fixes, new clocks and USB GDSCs are introduced for IPQ8074
and for MSM8939 a series of fixes for issues introduced by inheriting
the MSM8916 GCC driver is introduced.
- Support for a new type of voteable GDSCs are introduced and put in
use for the SC8280XP PCIe GDSCs. SC8280XP pipe clocks transitioned to
the new phy-mux implementation.
- MSM8996 GCC, the RPM clock driver and some clocks in MSM8994 GCC are
transitioned to use parent_data.
- The topology for Titan (camera) GDSCs on SDM845 and SM8250 are corrected
and MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on MSM8960 is reworked to mimic the design in
IPQ8074 and allow the GCC driver to probe earlier.
- The regulator based mmcx supply for dispcc and videocc is dropped, as
the only upstream target that adapted this interface was transitioned
several kernel versions ago.
- GDSCs found to be enabled at boot will now reflect in the enable
count of the supply, as was done with the regulator supplies
previously.
* tag 'qcom-clk-for-5.20' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (62 commits)
clk: qcom: gcc-msm8994: use parent_hws for gpll0/4
clk: qcom: clk-rpm: convert to parent_data API
dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
clk: qcom: fix build error initializer element is not constant
dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
clk: qcom: add support for SM8350 DISPCC
clk: qcom: add support for SM8350 GPUCC
clk: qcom: add camera clock controller driver for SM8450 SoC
clk: qcom: clk-alpha-pll: add Rivian EVO PLL configuration interfaces
clk: qcom: clk-alpha-pll: add Lucid EVO PLL configuration interfaces
clk: qcom: clk-alpha-pll: limit exported symbols to GPL licensed code
clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description
...
|
|
Allow 'iommu-map', 'iommu-map-mask', and 'msi-parent' properties for
generic host. This fixes unevaluated property warnings on Arm Juno, AMD
Seattle, and FSL LS1028a.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220728175137.1172841-1-robh@kernel.org
|
|
Support more than Gen2 speed link mode, since i.MX8MP PCIe supports up to
Gen3 link speed.
Link: https://lore.kernel.org/r/1658287576-26908-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers. To
make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN
properly when writing the DBI registers.
Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions.
Encapsulate clocks, regulators disables and PHY uninitialization into
imx6_pcie_host_exit().
To keep suspend/resume symmetric as much as possible, invoke these two
new created functions in suspend callback.
To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable()
to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Move the imx6_pcie_ltssm_disable() earlier and place it just behind the
imx6_pcie_ltssm_enable(), since it might not be only used by suspend
callback directly.
To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ
switch cases in imx6_pcie_ltssm_disable().
Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
imx6_pcie_clk_enable() enables clocks in the order:
pcie_phy
pcie_bus
pcie
imx6_pcie_enable_ref_clk
Change imx6_pcie_clk_disable() to disable them in the reverse order.
Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
|
|
Move the phy_power_on() to host_init from imx6_pcie_clk_enable().
Move the phy_init() to host_init from imx6_pcie_deassert_core_reset().
Refine the error handling in imx6_pcie_host_init() accordingly.
Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
i.MX PCIe doesn't support hotplug. During resume, only start PCIe link
training when the link was up before system suspend to avoid the long
latency in the link training period.
Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If the PCIe link is down, return zero from imx6_pcie_start_link() so the
driver will probe successfully.
Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Move regulator enable out of imx6_pcie_deassert_core_reset(), since the
regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset().
Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The driver should undo any enables it did itself. The regulator disable
shouldn't be basing decisions on regulator_is_enabled().
Move the regulator_disable to the suspend function, turn off regulator when
the system is in suspend mode.
Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
