| Age | Commit message (Collapse) | Author |
|---|
|
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_prio_stats[i].str, prio);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_tc_stats[i].str, tc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I thought header search paths to tools/include(/uapi) were unneeded,
but it looks like a build error occurs depending on the compiler.
Commit 303a339f30a9 ("bpfilter: remove extra header search paths for
bpfilter_umh") reintroduced the build error fixed by commit ae40832e53c3
("bpfilter: fix a build err").
Apology for the breakage, and thanks to Guenter for reporting this.
Fixes: 303a339f30a9 ("bpfilter: remove extra header search paths for bpfilter_umh")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
to support compound IOMMU groups.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/sriov: Register IOMMU groups for VFs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
|
|
Use devm_hwmon_device_register_with_info() instead of
devm_hwmon_device_register_with_groups() to register the hwmon
device to simplify the code and make it easier to maintain.
As part of this change, thermal device registration is moved into
the hwmon core.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This adds optional regulator support to the pwm-fan driver. This is
necessary for pwm fans which are powered by a switchable supply.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This adds an optional regulator support (e.g. switchable supply) to the
pwm fan binding.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clockevents updates from Daniel Lezcano:
- Update the binding documentation for the gpt timer (Anson Huang)
- Improve checking and error handling at init time on risc timer (Atish
Patra)
- Update the binding documentation for r8a774c0 cmt and tmu (Biju Das)
- Fail gracefully when clock rate is unavailable on sun5i (Chen-Yu Tsai)
- Rename the tango-xtal, pxa and cs5535 to timer-*.c for consistency
(Daniel Lezcano)
- Add the support for the tegra210 timer and add the platform's Kconfig
selection (Joseph Lo)
- Do a cleanup in the header inclusions and remove the unused ones for the
exynos_mct timer driver (Krzysztof Kozlowski)
- Remove some non-of dead code and fix the error path when initializing
the resources in the exynos_mct timer driver (Marek Szyprowski)
- Update the DT bindings for the MT7629 (Ryder Lee)
- Provide a workaround for the arm arch timer for Allwinner A64 timers
(Samuel Holland)
- Clear the timer interrupt at shutdown time on the exynos_mct timer
driver (Stuart Menefy)
|
|
The tegra timer is necessary for Tegra210 to support CPU idle power-down
state. So select it by default.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Add support for the Tegra210 timer that runs at oscillator clock
(TMR10-TMR13). We need these timers to work as clock event device and to
replace the ARMv8 architected timer due to it can't survive across the
power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up
source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Tegra210 timer provides fourteen 29-bit timer counters and one 32-bit
timestamp counter. The TMRs run at either a fixed 1 MHz clock rate derived
from the oscillator clock (TMR0-TMR9) or directly at the oscillator clock
(TMR10-TMR13). Each TMR can be programmed to generate one-shot periodic,
or watchdog interrupts.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The i.MX GPT timer driver binding doc is out of date,
update it according to current GPT timer driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The driver does not use sched.h and platform_device.h.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Update the binding for MT7629 SoC, which uses fallback compatible to
MT6765 SYST, so add more descriptions to distinguish it from the other
SoCs that use GPT.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
While freeing interrupt handlers in error path, don't assume that all
requested interrupts are per-processor interrupts and properly release
standard interrupts too.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 56a94f13919c ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Exynos Multi-Core Timer driver is used only on device-tree based
systems, so remove non-dt related code. In case of !CONFIG_OF
the code is anyway equal because of_irq_count() has a stub
returning 0. Device node pointer is always provided when driver
has been probed from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently, clocksource registration happens for an invalid cpu for
non-smp kernels. This lead to kernel panic as cpu hotplug registration
will fail for those cpus. Moreover, riscv_hartid_to_cpuid can return
errors now.
Do not proceed if hartid or cpuid is invalid. Take this opportunity to
print appropriate error strings for different failure cases.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document RZ/G2E (R8A774C0) SoC in the Renesas TMU bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document SoC specific bindings for RZ/G2E (r8a774c0) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
When shutting down the timer, ensure that after we have stopped the
timer any pending interrupts are cleared. This fixes a problem when
suspending, as interrupts are disabled before the timer is stopped,
so the timer interrupt may still be asserted, preventing the system
entering a low power state when the wfi is executed.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
When a timer tick occurs and the clock is in one-shot mode, the timer
needs to be stopped to prevent it triggering subsequent interrupts.
Currently this code is in exynos4_mct_tick_clear(), but as it is
only needed when an ISR occurs move it into exynos4_mct_tick_isr(),
leaving exynos4_mct_tick_clear() just doing what its name suggests it
should.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).
Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.
Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:
Count | Event
-------+---------------------------
9940 | jumped backward 699ms
268 | jumped backward 1398ms
1 | jumped backward 2097ms
16020 | jumped forward 175ms
6443 | jumped forward 699ms
2976 | jumped forward 1398ms
9 | jumped forward 356516ms
9 | jumped forward 357215ms
4 | jumped forward 714430ms
1 | jumped forward 3578440ms
This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.
The largest jump (almost an hour!) was the following sequence of reads:
0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000
Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.
Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.
Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:
Count | Event
-------+---------------------------
17 | jumped backward 699ms
52 | jumped forward 175ms
2831 | jumped forward 699ms
5 | jumped forward 1398ms
Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000000d4a2d8bfff | 0x10003fff | 0x000000d4b2d8bfff | +0x00004000
0x000000d4a2d94000 | 0x0fffffff | 0x000000d4b2d97fff | -0x00004000
0x000000d4a2d97fff | 0x10003fff | 0x000000d4b2d97fff | +0x00004000
0x000000d4a2d9c000 | 0x0fffffff | 0x000000d4b2d9ffff | -0x00004000
The pattern of errors in CNTV_TVAL seemed to depend on exactly which
value was written to it. For example, after writing 0x10101010:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000001ac3effffff | 0x1110100f | 0x000001ac4f10100f | +0x1000000
0x000001ac40000000 | 0x1010100f | 0x000001ac5110100f | -0x1000000
0x000001ac58ffffff | 0x1110100f | 0x000001ac6910100f | +0x1000000
0x000001ac66000000 | 0x1010100f | 0x000001ac7710100f | -0x1000000
0x000001ac6affffff | 0x1110100f | 0x000001ac7b10100f | +0x1000000
0x000001ac6e000000 | 0x1010100f | 0x000001ac7f10100f | -0x1000000
I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:
CNTVCT | CNTV_TVAL | CNTV_CVAL
--------------------+------------+--------------------------------------
0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past)
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
========================================================================
Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.
However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.
For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.
Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".
[1]: https://github.com/armbian/build/commit/a08cd6fe7ae9
[2]: https://forum.armbian.com/topic/3458-a64-datetime-clock-issue/
[3]: https://irclog.whitequark.org/linux-sunxi/2018-01-26
[4]: https://github.com/Allwinner-Homlet/H6-BSP4.9-linux/blob/master/drivers/clocksource/arm_arch_timer.c#L272
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
If the clock tree is not fully populated when the timer-sun5i init code
is called, attempts to get the clock rate for the timer would fail and
return 0.
Make the init code for both clock events and clocksource check the
returned clock rate and fail gracefully if the result is 0, instead of
causing a divide by 0 exception later on.
Fixes: 4a59058f0b09 ("clocksource/drivers/sun5i: Refactor the current code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull keys fixes from James Morris:
"Two fixes from Eric Biggers"
* 'fixes-v5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: always initialize keyring_index_key::desc_len
KEYS: user: Align the payload buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
|
|
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
|
|
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
? 0xffffffffc0e40000
? 0xffffffffc0e40000
? 0xffffffffc0e40000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
Allocated by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
kmalloc include/linux/slab.h:545 [inline]
kzalloc include/linux/slab.h:740 [inline]
mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kfree+0xe1/0x270 mm/slub.c:3938
device_release+0x78/0x200 drivers/base/core.c:919
kobject_cleanup lib/kobject.c:662 [inline]
kobject_release lib/kobject.c:691 [inline]
kref_put include/linux/kref.h:67 [inline]
kobject_put+0x146/0x240 lib/kobject.c:708
put_device+0x1c/0x30 drivers/base/core.c:2060
__mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881dc824c80
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vinod Koul says:
====================
net: phy: at803x: Update delays for RGMII modes
Peter[1] reported that patch cd28d1d6e52e: ("net: phy: at803x: Disable
phy delay for RGMII mode") caused regression on am335x-evmsk board.
This board expects the Phy delay to be enabled but specified RGMII mode
which refers to delays being disabled. So fix this by disabling delay only
for RGMII mode and enable for RGMII_ID and RGMII_TXID/RXID modes.
While at it, as pointed by Dave, don't inline the helpers.
[1]: https://www.spinics.net/lists/netdev/msg550749.html
Changes in v4:
- fix log & comments nbased on Marc's feedback
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For tcindex filter, it is too late to initialize the
net pointer in tcf_exts_validate(), as tcf_exts_get_net()
requires a non-NULL net pointer. We can just move its
initialization into tcf_exts_init(), which just requires
an additional parameter.
This makes the code in tcindex_alloc_perfect_hash()
prettier.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: firmware message delay fixes.
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
