| Age | Commit message (Collapse) | Author |
|---|
|
The Thinkpad T14s has 2 USB-A ports, both connected to the USB
multiport controller, each one via a separate NXP PTN3222 eUSB2-to-USB2
redriver to the eUSB2 PHY for High-Speed support, with a dedicated QMP
PHY for SuperSpeed support.
Describe each redriver and then enable each pair of PHYs and the
USB controller itself, in order to enable support for the 2 USB-A ports.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241202-x1e80100-qcp-t14-enable-usb-type-a-ports-v2-1-7360ed65c769@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Previously the interrupt lanes were not described, fix that.
Fixes: d9be0bc95f25 ("arm64: dts: qcom: msm8994: Add USB support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20241129-topic-qcom_usb_dtb_fixup-v1-4-cba24120c058@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the missing interrupt lines and fix qusb2_phy being an impostor
of hs_phy_irq.
This happens to also fix warnings such as:
usb@6af8800: interrupt-names: ['hs_phy_irq', 'ss_phy_irq'] is too short
Fixes: 4753492de9df ("arm64: dts: qcom: msm8996: Add usb3 interrupts")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241129-topic-qcom_usb_dtb_fixup-v1-3-cba24120c058@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
properties
Remove "ti,(rx|tx)-fifo-depth" properties which are both unused in the
kernel and undocumented. Most likely they are leftovers from downstream.
There are similar properties, but DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
represents the default value so adding them is not necessary.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241115193359.3618020-1-robh@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
ICSSG has 7 available clocks per instance. Add all the cloks to ICSSG
nodes. ICSSG currently uses ICSSG_ICLK (clk id 20) which operates at
250MHz. Switch ICSSG clock to ICSSG_CORE clock (clk id 0) which operates at
333MHz.
ICSSG_CORE clock will help get the most out of ICSSG as more cycles are
needed to fully support all ICSSG features.
This commit also changes assigned-clock-parents of coreclk-mux to
ICSSG_CORE clock from ICSSG_ICLK.
Performance update in dual mac mode
With ICSSG_CORE Clk @ 333MHz
Tx throughput - 934 Mbps
Rx throughput - 914 Mbps,
With ICSSG_ICLK clk @ 250MHz,
Tx throughput - 920 Mbps
Rx throughput - 706 Mbps
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241113110955.3876045-3-danishanwar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
The ICSSG module has 7 clocks for each instance.
These clocks are ICSSG0_CORE_CLK, ICSSG0_IEP_CLK, ICSSG0_ICLK,
ICSSG0_UART_CLK, RGMII_MHZ_250_CLK, RGMII_MHZ_50_CLK and RGMII_MHZ_5_CLK
These clocks are described in AM64x TRM Section 6.4.3 Table 6-398.
Add these clocks to the dt binding of ICSSG.
Link: https://www.ti.com/lit/pdf/spruim2 (AM64x TRM)
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241113110955.3876045-2-danishanwar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Enable the A615 GPU and GMU for the Pixel 3a. It has zap firmware, so
add that in as well.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20240806214452.16406-11-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The Snapdragon 670 has the Adreno A615 GPU. Add it along with its device
tree dependencies.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20240806214452.16406-10-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add following coresight components for QCS8300 platform.
It includes CTI, dummy sink, dynamic Funnel, Replicator, STM,
TPDM, TPDA and TMC ETF.
Signed-off-by: Jie Gan <quic_jiegan@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241219024208.3462358-1-quic_jiegan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add support for audio on Lenovo T14s laptop, coming with two speakers,
audio jack and two digital microphones.
This is very early work, not yet complete:
1. 2x speakers: work OK.
2. 2x digital microphones: work OK.
3. Headset (audio jack) recording: does not work.
4. Headphones playback (audio jack): channels are intermixed.
[krzysztof: correct DMIC routing and vamacro pinctrl, re-order nodes,
add commit msg]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241203111229.48967-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
In order for the MCU domain to access this PMIC, a regulator
needs to be marked appropriately otherwise it is not seen by SPL and
therefore not configured.
This is necessary if the MCU domain is to program the TPS6594 MCU ESM
state machine, which is required to wire up the watchdog in a manner
that will reset the board.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Beleswar Padhi <b-padhi@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Enric Balletbo i Serra <eballetb@redhat.com>
Link: https://lore.kernel.org/r/20241113-b4-j784s4-tps6594-bootph-v4-2-102ddaa1bdc6@redhat.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
In order for the MCU domain to access this PMIC, a regulator
needs to be marked appropriately otherwise it is not seen by SPL and
therefore not configured.
This is necessary if the MCU domain is to program the TPS6594 MCU ESM
state machine, which is required to wire up the watchdog in a manner
that will reset the board.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Beleswar Padhi <b-padhi@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Enric Balletbo i Serra <eballetb@redhat.com>
Link: https://lore.kernel.org/r/20241113-b4-j784s4-tps6594-bootph-v4-1-102ddaa1bdc6@redhat.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
After the SoC has entered the Deep Sleep mode, USB1 can be used to wakeup
the SoC based on USB events triggered by USB devices. This requires that
the pin corresponding to the Type-A connector remains pulled up even after
the SoC has entered the Deep Sleep mode. Hence, enable Deep Sleep pullup /
pulldown selection for the USB1_DRVVBUS pin and set its Deep Sleep state to
PULL_UP.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205120134.754664-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
The behavior of pins in deep sleep mode can be configured by programming
the corresponding bits in the respective Pad Configuration register. Add
macros to support this.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205120134.754664-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
The clock IDs for multiple MCSPI instances across wakeup domain in
J784s4 are incorrect when compared with documentation [1]. Fix the
clock IDs to their appropriate values.
[1] https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j784s4/clocks.html
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Link: https://lore.kernel.org/r/20241104121241.102027-1-a-dutta@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Add the missing vcc-supply property to the EEPROM node which resolves
the following warning:
at24 1-0051: supply vcc not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-4-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Specify the regulator for the EEPROM supply voltage and associate it
with the EEPROM device. This resolves the following warning:
at24 0-0050: supply vcc not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-3-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Specify I/0 voltage & core supply regulators used by the SII902x
HDMI bridge and make them known to the bridge.
This resolves the following warning:
sii902x 1-0039: supply iovcc not found, using dummy regulator
sii902x 1-0039: supply cvcc12 not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-2-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
The phyBOARD-Lyra connects only 16 pins to the SII902x HDMI bridge's RGB
input. The default 24-bit setting causes incorrect color output. Update
to 16-bit to match the hardware configuration.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-1-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Although the HDK has no radio, the IPA part is still perfectly usable
(altough it doesn't register any real networking devices). Enable it to
make it possible to test IPA on this platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230310203438.1585701-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add bluetooth node and this bluetooth module is connected to uart.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Link: https://lore.kernel.org/r/20241201135716.141691-3-lujianhua000@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add wifi node and this wifi module is connected to PCIe port.
The following is qca6390 probe message:
ath11k_pci 0000:01:00.0: Adding to iommu group 12
ath11k_pci 0000:01:00.0: BAR 0 [mem 0x60400000-0x604fffff 64bit]: assigned
ath11k_pci 0000:01:00.0: enabling device (0000 -> 0002)
ath11k_pci 0000:01:00.0: MSI vectors: 32
ath11k_pci 0000:01:00.0: qca6390 hw2.0
ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
ath11k_pci 0000:01:00.0: fw_version 0x10121492 fw_build_timestamp 2021-11-04 11:23 fw_build_id
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Link: https://lore.kernel.org/r/20241201135716.141691-2-lujianhua000@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add qca6390-pmu node, which is used to manage power supply sequence for wifi and
bluetooth on sm8250 soc based devices.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Link: https://lore.kernel.org/r/20241201135716.141691-1-lujianhua000@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
As pointed out by Intel's robot, the node name doesn't adhere to
dt-bindings.
Fix errors like this one:
qcs9100-ride.dtb: qcom,gpi-dma@800000: $nodename:0: 'qcom,gpi-dma@800000' does not match '^dma-controller(@.*)?$'
Fixes: 34d17ccb5db8 ("arm64: dts: qcom: sa8775p: Add GPI configuration")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411080206.vFLRjIBZ-lkp@intel.com/
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241107-topic-sa8775_dma-v1-1-eb633e07b007@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The Qualcomm SA8775P platform comes with 2 DisplayPort controllers
for each mdss. edp0 and edp1 correspond to the DP controllers of
mdss0, whereas edp2 and edp3 correspond to the DP controllers of
mdss1. This change enables only the DP controllers, DPTX0 and DPTX1
alongside their corresponding PHYs of mdss0, which have been
validated.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241125105747.6595-3-quic_mukhopad@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add device tree nodes for the DPTX0 and DPTX1 controllers
with their corresponding PHYs found on Qualcomm SA8775P SoC.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com>
Link: https://lore.kernel.org/r/20241125105747.6595-2-quic_mukhopad@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add an ICE node to qcs8300 SoC description and enable it by adding a
phandle to the UFS node.
Signed-off-by: Yuvaraj Ranganathan <quic_yrangana@quicinc.com>
Link: https://lore.kernel.org/r/20241125065801.1751256-3-quic_yrangana@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The qcs8300 SoC has a True Random Number Generator, add the node with
the correct compatible set.
Signed-off-by: Yuvaraj Ranganathan <quic_yrangana@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241125064317.1748451-3-quic_yrangana@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20241123221708.862901-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the watchdog node for IPQ5424 SoC.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20241121051951.1776250-3-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add ADSP and CDSP0 fastrpc nodes for QCS8300 platform.
Signed-off-by: Ling Xu <quic_lxu5@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241119120635.687936-1-quic_lxu5@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Commit 4f79d0deae37 ("arm64: dts: qcom: sa8775p: add CPU idle states")
already added cpu and cluster idle-states but have not added CPU devices
to psci power domain without which idle states do not get detected.
Add CPUs to psci power domain.
Fixes: 4f79d0deae37 ("arm64: dts: qcom: sa8775p: add CPU idle states")
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241112-sa8775p_cpuidle-v1-1-66ff3ba72464@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The Pixel 3a has two identical flash LEDs. Add them together.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241112024050.669578-9-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The PM660L has support for QPNP flash LEDs. Add them to the device tree.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20241112024050.669578-8-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The commit adding these nodes did not use a SoC-specific node, fix that
to comply with bindings guidelines.
Fixes: 34d17ccb5db8 ("arm64: dts: qcom: sa8775p: Add GPI configuration")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241108-topic-sa8775_dma2-v1-2-1d3b0d08d153@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add devicetree changes to enable MDSS0 display-subsystem its
display-controller(DPU) for Qualcomm SA8775P platform.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Mahadevan <quic_mahap@quicinc.com>
Link: https://lore.kernel.org/r/20241019-patchv3_1-v5-5-d2fb72c9a845@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add support for video, camera, display0 and display1 clock controllers
on SA8775P. The dispcc1 will be enabled based on board requirements.
Reviewed-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241025-sa8775p-mm-v4-resend-patches-v6-2-329a2cac09ae@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Fix the sleep_clk frequency is 32000 on SA8775P.
Fixes: 603f96d4c9d0 ("arm64: dts: qcom: add initial support for qcom sa8775p-ride")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20241025-sa8775p-mm-v4-resend-patches-v6-1-329a2cac09ae@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The UFS driver expects to be able to set load (and by extension, mode)
on its supply regulators. Add the necessary properties to make that
possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rakesh Kota <quic_kotarake@quicinc.com>
Link: https://lore.kernel.org/r/20241017122858.3664474-1-quic_kotarake@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The LP5562 led@1 reg property should likely be set to 1 to match
the unit. Fix it.
Fixes: 4ac46b3682c5 ("arm64: dts: qcom: msm8996: xiaomi-gemini: Add support for Xiaomi Mi 5")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241006022012.366601-1-marex@denx.de
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
RB3 Gen2 has a trio of LEDs connected to the PM8350C's Light Pulse
Generator. Describe them.
Use the "red channel" as a panic indicator by default.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
[bjorn: Corrected colors]
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241004-rb3gen2-leds-v1-2-437cdbb4f6c0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The downstream tree described more SDAM slices on the PMIC. Some of
them are actually required by other peripherals, whereas other are nice
to add for hardware description purposes.
Add them in.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241004-rb3gen2-leds-v1-1-437cdbb4f6c0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable the PCIe controller and PHY nodes corresponding to RDP 433.
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Link: https://lore.kernel.org/r/20240801054803.3015572-4-quic_srichara@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Link: https://lore.kernel.org/r/20240801054803.3015572-3-quic_srichara@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the lid switch for the Lenovo Yoga Slim 7x.
Other x1e80100 laptops use the GPIO pin 92 only, however on the Yoga
Slim 7x this pin seems to be bridged with the pin 71. By default, the
pin 71 is set as output-high, which blocks any event on pin 92.
This patch sets the pin 71 as output-disable and sets the LID switch on
pin 92. This is aligned with how they're configured on Windows:
GPIO 71 | 0xf147000 | in | func0 | hi | pull up | 16 mA
GPIO 92 | 0xf15c000 | in | func0 | lo | no pull | 2 mA
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Anthony Ruhier <aruhier@mailbox.org>
Link: https://lore.kernel.org/r/20241219-patch-lenovo-yoga-v3-1-9c4a79068141@mailbox.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The path MASTER_QUP_0 to SLAVE_EBI_CH0 would be qup-memory path and not
qup-config. Since the qup-memory path is not part of the qcom,geni-uart
bindings, just replace that path with the correct path for qup-config.
Fixes: b179f35b887b ("arm64: dts: qcom: sm6350: add uart1 node")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241220-sm6350-uart1-icc-v1-1-f4f10fd91adf@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X1 family is split into two parts: the 10- and 12-core parts are
variants of the same silicon with different fusing, whereas the 8-core
ones are a separate design. Thankfully, the software interface is only
barely different, letting us reuse much of the existing X1 work.
Add X1P42100 SoC (and the CRD based on it) as a representative of the
8-core series.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20241221-topic-x1p4_soc-v1-2-55347831d73c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X1 series includes SoCs like X1P42100. Extend the pattern x1e match
to x1[ep] to also include these.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20241221-topic-x1p4_soc-v1-1-55347831d73c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the QCE and Crypto BAM DMA nodes.
Signed-off-by: Yuvaraj Ranganathan <quic_yrangana@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241223110936.3428125-1-quic_yrangana@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The pp3300_panel fixed regulator is just a load switch. It does not have
any regulating capabilities. Thus having voltage constraints on it is
wrong.
Remove the voltage constraints.
Fixes: cabc71b08eb5 ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241030070224.1006331-2-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
