| Age | Commit message (Collapse) | Author |
|---|
|
During the v6.14-rc cycles, there has been an issue with syscons which
prevented TI chipid controller to probe, itself preventing the only DMA
engine on AM62A with the memcpy capability to probe, which is needed for
the SPI controller to work in its most efficient configuration.
The SPI controller on AM62A can be used in DAC and INDAC mode, which are
some kind of direct mapping vs. CPU-controlled SPI operations,
respectively. However, because of hardware constraints (some kind of
request line not being driven), INDAC mode cannot leverage DMA without
risking to underflow the SPI FIFO. This mode costs a lot of CPU
cycles. On the other side however, DAC mode can be used with and without
DMA support, but in practice, DMA transfers are way more efficient
because of the burst capabilities that the CPU does not have.
As a result, in terms of read throughput, using a Winbond chip in 1-8-8
SDR mode, we get:
- 3.5MiB/s in DAC mode without DMA
- 9.0MiB/s in INDAC mode (CPU more busy)
- a fluctuating 9 to 12MiB/s in DAC mode with DMA (a constant 14.5MiB/s
without CPUfreq)
The reason for the patch that is being reverted is that because of the
syscon issue, we were using a very un-efficient DAC configuration (no
DMA), but since:
commit 5728c92ae112 ("mfd: syscon: Restore device_node_to_regmap() for non-syscon nodes")
the probing of the DMA controller has been fixed, and the performances are
back to normal, so we can safely revert this commit.
This is a revert of:
commit cce2200dacd6 ("spi: cadence-qspi: Improve spi memory performance")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250401134748.242846-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If requested_clk > 128, cdns_mrvl_xspi_setup_clock() iterates over the
entire cdns_mrvl_xspi_clk_div_list array without breaking out early,
causing 'i' to go beyond the array bounds.
Fix that by stopping the loop when it gets to the last entry, clamping
the clock to the minimum 6.25 MHz.
Fixes the following warning with an UBSAN kernel:
vmlinux.o: warning: objtool: cdns_mrvl_xspi_setup_clock: unexpected end of section .text.cdns_mrvl_xspi_setup_clock
Fixes: 26d34fdc4971 ("spi: cadence: Add clock configuration for Marvell xSPI overlay")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503282236.UhfRsF3B-lkp@intel.com/
Link: https://lore.kernel.org/r/gs2ooxfkblnee6cc5yfcxh7nu4wvoqnuv4lrllkhccxgcac2jg@7snmwd73jkhs
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://patch.msgid.link/h6bef6wof6zpjfp3jbhrkigqsnykdfy6j4qmmvb6gsabhianhj@k57a7hwpa3bj
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Driver use devm APIs to manage clk/irq/resources and register the spi
controller, but the legacy remove function will be called first during
device detach and trigger kernel panic. Drop the remove function and use
devm_add_action_or_reset() for driver cleanup to ensure the release
sequence.
Trigger kernel panic on i.MX8MQ by
echo 30bb0000.spi >/sys/bus/platform/drivers/fsl-quadspi/unbind
Cc: stable@vger.kernel.org
Fixes: 8fcb830a00f0 ("spi: spi-fsl-qspi: use devm_spi_register_controller")
Reported-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250326224152.2147099-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI_QPIC_SNAND is the only driver that selects MTD instead of depending
on it, which could lead to circular dependencies. Moreover, as
SPI_QPIC_SNAND is bool, this forces MTD (and various related symbols) to
be built-in, as can be seen in an allmodconfig kernel.
Except for a missing semicolon, there is no reason why SPI_QPIC_SNAND
cannot be tristate; all MODULE_*() boilerplate is already present.
Hence make SPI_QPIC_SNAND tristate, let it depend on MTD, and add the
missing semicolon.
Fixes: 7304d1909080ef0c ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/b63db431cbf35223a4400e44c296293d32c4543c.1742998909.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Do not write native chip select stuff for GPIO chip selects.
GPIOs can be numbered much higher than native CS.
Also, it makes no sense.
Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Link: https://patch.msgid.link/365ccddfba110549202b3520f4401a6a936e82a8.camel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
While working with this controller I figured out a couple of small
issues which I propose to fix. They are not super impacting, but I
believe this goes into the right direction.
|
|
Many spi-mem controller drivers have a very similar debug log at the
beginning of their ->exec_op() callback implementation. This debug log is
effectively useful, so let's create one that is complete and concise
enough, so developers no longer need to write their own. The verbosity
being high, VERBOSE_DEBUG will be required in this case.
Remove the debug log from individual drivers and propose a common one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20250320115644.2231240-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are 5 mandatory peripheral properties. They are described in a
separate binding but not explicitly required. Make sure they are
correctly marked required and update the example to reflect this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250319094651.1290509-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The initial SPI controller IP from Cadence has always been implemented
into controllers from various hardware manufacturers and because of
that, it has always been (rightfully) doubled with a more specific
compatible. There are likely no reasons to keep this compatible
legitimate, alone. Make sure people do not get mislead by officially
deprecating this compatible.
While at deprecating, let's update the examples to avoid documenting
deprecated properties.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250319094651.1290509-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
controller is
Despite being very common in commit logs, SPI NOR controllers simply do
not exist. At least, they are not as specific as the name implies. There
are SPI memory controllers which are indeed "specialized" and optimized
for handling "memories", but most of them are just generic and accept
almost any kind of opcode, address, dummy and data cycles, making them
as suitable for NANDs than NORs.
Furthermore, this controller supports any kind of bus, from single to
octal NAND, so make it clear.
Also add a comment to mention that the initial compatible naming is too
specific (but obviously kept for backward compatibility reasons).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250319094651.1290509-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Dan Carpenter <dan.carpenter@linaro.org>:
Here are two fixes for Smatch warnings.
Dan Carpenter (2):
spi: sg2044-nor: fix signedness bug in sg2044_spifmc_write()
spi: sg2044-nor: Fix uninitialized variable in probe
drivers/spi/spi-sg2044-nor.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
--
2.47.2
|
|
of_gpio.h should be deprecated, use "gpio/consumer.h".
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20250318045549.1711502-1-peng.fan@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 8f1cc5242544 ("MAINTAINERS: add maintainer for the GOcontroll
Moduline module slot") adds a new MAINTAINERS section referring to the
non-existent file:
Documentation/connector/gocontroll,moduline-module-slot.yaml
It intends to refer to the file with the same name in
Documentation/devicetree/bindings/connector/. Adjust the file reference to
the intended location.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Maud Spierings <maudspierings@gocontroll.com>
Link: https://patch.msgid.link/20250318080913.31455-1-lukas.bulwahn@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
They are a dependency for applying some changes to the MAINTAINERS
file.
|
|
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
The driver has one ordering issue and one missed case for dev_err_probe().
Address that in this mini-series.
|
|
When the allocation of the OOB buffer fails, the
qcom_spi_ecc_init_ctx_pipelined() function returns without freeing
the memory allocated for 'ecc_cfg' thus it can cause a memory leak.
Call kfree() to free 'ecc_cfg' before returning from the function
to avoid that.
Fixes: 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250313-qpic-snand-memleak-fix-v1-1-e54e78d1da3a@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The return value of spi_setup() is not captured within
spi_mux_select() and it is assumed to be always success.
CID: 1638374
Signed-off-by: Sergio Perez Gonzalez <sperezglz@gmail.com>
Link: https://patch.msgid.link/20250316054651.13242-1-sperezglz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sg2044_spifmc_write() function uses 'ret' of unsigned type
size_t to capture return values from sg2044_spifmc_wait_xfer_size()
and sg2044_spifmc_wait_int(). Since these functions may return
negative error codes, using an unsigned type prevents proper
error detection, as size_t cannot represent negative values.
Change 'ret' to type int so that negative values are handled correctly.
Fixes: de16c322eefb ("spi: sophgo: add SG2044 SPI NOR controller driver")
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250313214545.7444-1-qasdev00@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "base" pointer is uninitialized. It should be "spifmc->io_base"
instead.
Fixes: de16c322eefb ("spi: sophgo: add SG2044 SPI NOR controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/d343921b-16b8-429b-888a-f51bb6f2edc8@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "ret" variable needs to be signed for the error handling to work.
It should be type int, since it only holds zero and negative error
codes.
Fixes: de16c322eefb ("spi: sophgo: add SG2044 SPI NOR controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/4e16e1bf-e5fb-4771-bc92-c5cba9aac473@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
One of the cases in sg2044_spifmc_probe() may be converted to use
dev_err_probe(). Do it.
While at it, use local device pointer in all such calls and drop
unneeded __func__ parameter as dev_err_probe() is assumed to be called
only during probe phase.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250313111423.322775-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver has a wrong order of the cleaning up the resources,
i.e. it first will destroy the mutex and only then free the SPI
which might still use it. Fix this by switching to devm_mutex_init().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250313111423.322775-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"rtl2832 driver regression fix"
* tag 'media/v6.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rtl2832_sdr: assign vb2 lock before vb2_queue_init
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- omap: fix irq ACKS to avoid irq storming and system hang
- ali1535, ali15x3, sis630: fix error path at probe exit
* tag 'i2c-for-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sis630: Fix an error handling path in sis630_probe()
i2c: ali15x3: Fix an error handling path in ali15x3_probe()
i2c: ali1535: Fix an error handling path in ali1535_probe()
i2c: omap: fix IRQ storms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix ref count of trace_array in error path of histogram file open
Tracing instances have a ref count to keep them around while files
within their directories are open. This prevents them from being
deleted while they are used.
The histogram code had some files that needed to take the ref count
and that was added, but the error paths did not decrement the ref
counts. This caused the instances from ever being removed if a
histogram file failed to open due to some error"
* tag 'trace-v6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Correct the refcount if the hist/hist_debug file fails to open
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes and new
usb-serial device ids. Included in here are:
- new usb-serial device ids
- typec driver bugfix
- thunderbolt driver resume bugfix
All of these have been in linux-next with no reported issues"
* tag 'usb-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: fix state transition for SNK_WAIT_CAPABILITIES state in run_state_machine()
USB: serial: ftdi_sio: add support for Altera USB Blaster 3
thunderbolt: Prevent use-after-free in resume from hibernate
USB: serial: option: fix Telit Cinterion FE990A name
USB: serial: option: add Telit Cinterion FE990B compositions
USB: serial: option: match on interface class for Telit FN990B
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- several new device IDs added to xpad game controller driver
- support for imagis IST3038H variant of chip added to imagis touch
controller driver
- a fix for GPIO allocation for ads7846 touch controller driver
- a fix for iqs7222 driver to properly support status register
- a fix for goodix-berlin touch controller driver to use the right name
for the regulator
- more i8042 quirks to better handle several old Clevo devices.
* tag 'input-for-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
MAINTAINERS: Remove myself from the goodix touchscreen maintainers
Input: iqs7222 - preserve system status register
Input: i8042 - swap old quirk combination with new quirk for more devices
Input: i8042 - swap old quirk combination with new quirk for several devices
Input: i8042 - add required quirks for missing old boardnames
Input: i8042 - swap old quirk combination with new quirk for NHxxRZQ
Input: xpad - rename QH controller to Legion Go S
Input: xpad - add support for TECNO Pocket Go
Input: xpad - add support for ZOTAC Gaming Zone
Input: goodix-berlin - fix vddio regulator references
Input: goodix-berlin - fix comment referencing wrong regulator
Input: imagis - add support for imagis IST3038H
dt-bindings: input/touchscreen: imagis: add compatible for ist3038h
Input: xpad - add multiple supported devices
Input: xpad - add 8BitDo SN30 Pro, Hyperkin X91 and Gamesir G7 SE controllers
Input: ads7846 - fix gpiod allocation
Input: wdt87xx_i2c - fix compiler warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Disallow BTF generation with Rust + LTO
- Improve rust-analyzer support
'kernel' crate:
- 'init' module: remove 'Zeroable' implementation for a couple types
that should not have it
- 'alloc' module: fix macOS failure in host test by satisfying POSIX
alignment requirement
- Add missing '\n's to 'pr_*!()' calls
And a couple other minor cleanups"
* tag 'rust-fixes-6.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
scripts: generate_rust_analyzer: add uapi crate
scripts: generate_rust_analyzer: add missing include_dirs
scripts: generate_rust_analyzer: add missing macros deps
rust: Disallow BTF generation with Rust + LTO
rust: task: fix `SAFETY` comment in `Task::wake_up`
rust: workqueue: add missing newline to pr_info! examples
rust: sync: add missing newline in locked_by log example
rust: init: add missing newline to pr_info! calls
rust: error: add missing newline to pr_warn! calls
rust: docs: add missing newline to printing macro examples
rust: alloc: satisfy POSIX alignment requirement
rust: init: fix `Zeroable` implementation for `Option<NonNull<T>>` and `Option<KBox<T>>`
rust: remove leftover mentions of the `alloc` crate
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify reverts from Jan Kara:
"Syzbot has found out that fsnotify HSM events generated on page fault
can be generated while we already hold freeze protection for the
filesystem (when you do buffered write from a buffer which is mmapped
file on the same filesystem) which violates expectations for HSM
events and could lead to deadlocks of HSM clients with filesystem
freezing.
Since it's quite late in the cycle we've decided to revert changes
implementing HSM events on page fault for now and instead just
generate one event for the whole range on mmap(2) so that HSM client
can fetch the data at that moment"
* tag 'fsnotify_for_v6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
Revert "fanotify: disable readahead if we have pre-content watches"
Revert "mm: don't allow huge faults for files with pre content watches"
Revert "fsnotify: generate pre-content permission event on page fault"
Revert "xfs: add pre-content fsnotify hook for DAX faults"
Revert "ext4: add pre-content fsnotify hook for DAX faults"
fsnotify: add pre-content hooks on mmap()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v6.14-rc7
- omap: fixed irq ACKS to avoid irq storming and system hang.
- ali1535, ali15x3, sis630: fixed error path at probe exit.
|
|
Pull smb server fixes from Steve French:
- Two fixes for oplock break/lease races
* tag 'v6.14-rc6-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: prevent connection release during oplock break notification
ksmbd: fix use-after-free in ksmbd_free_work_struct
|
|
Pull smb client fixes from Steve French:
"Six smb3 client fixes, all also for stable"
* tag 'v6.14-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: Fix match_session bug preventing session reuse
cifs: Fix integer overflow while processing closetimeo mount option
cifs: Fix integer overflow while processing actimeo mount option
cifs: Fix integer overflow while processing acdirmax mount option
cifs: Fix integer overflow while processing acregmax mount option
smb: client: fix regression with guest option
|
|
Pull another bcachefs hotfix from Kent Overstreet:
- fix 32 bit build breakage
* tag 'bcachefs-2025-03-14.2' of git://evilpiepirate.org/bcachefs:
bcachefs: fix build on 32 bit in get_random_u64_below()
|
|
bare 64 bit divides not allowed, whoops
arm-linux-gnueabi-ld: drivers/char/random.o: in function `__get_random_u64_below':
drivers/char/random.c:602:(.text+0xc70): undefined reference to `__aeabi_uldivmod'
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Pull xfs cleanup from Carlos Maiolino:
"Use abs_diff instead of XFS_ABSDIFF"
* tag 'xfs-fixes-6.14-rc7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Use abs_diff instead of XFS_ABSDIFF
|
|
Pull bcachefs hotfix from Kent Overstreet:
"This one is high priority: a user hit an assertion in the upgrade to
6.14, and we don't have a reproducer, so this changes the assertion to
an emergency read-only with more info so we can debug it"
* tag 'bcachefs-2025-03-14' of git://evilpiepirate.org/bcachefs:
bcachefs: Change btree wb assert to runtime error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mikulas Patocka:
- dm-flakey: fix memory corruption in optional corrupt_bio_byte feature
* tag 'for-6.14/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-flakey: Fix memory corruption in optional corrupt_bio_byte feature
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Concurrent pci error and hotplug handling fix (Keith)
- Endpoint function fixes (Damien)
- Fix for a regression introduced in this cycle with error checking for
batched request completions (Shin'ichiro)
* tag 'block-6.14-20250313' of git://git.kernel.dk/linux:
block: change blk_mq_add_to_batch() third argument type to bool
nvme: move error logging from nvme_end_req() to __nvme_end_req()
nvmet: pci-epf: Do not add an IRQ vector if not needed
nvmet: pci-epf: Set NVMET_PCI_EPF_Q_LIVE when a queue is fully created
nvme-pci: fix stuck reset on concurrent DPC and HP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Ilpo Järvinen:
"Fixes and new HW support.
The diff is a bit larger than I'd prefer at this point due to
unwinding the amd/pmf driver's error handling properly instead of
calling a deinit function that was a can full of worms.
Summary:
- amd/pmf:
- Fix error handling in amd_pmf_init_smart_pc()
- Fix missing hidden options for Smart PC
- surface: aggregator_registry: Add Support for Surface Pro 11"
* tag 'platform-drivers-x86-v6.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
MAINTAINERS: Update Ike Panhc's email address
platform/x86/amd: pmf: Fix missing hidden options for Smart PC
platform/surface: aggregator_registry: Add Support for Surface Pro 11
platform/x86/amd/pmf: fix cleanup in amd_pmf_init_smart_pc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"The first fix is a backport from my v6.15-rc1 queue that turned out to
be needed in v6.14 as well but as the former diverged from my fixes
branch I had to adjust the patch a bit.
The second one fixes a regression observed in user-space where closing
a file descriptor associated with a GPIO device results in a ~10ms
delay due to the atomic notifier calling rcu_synchronize() when
unregistering.
Summary:
- don't check the return value of gpio_chip::get_direction() when
registering a GPIO chip
- use raw notifier for line state events"
* tag 'gpio-fixes-for-v6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: cdev: use raw notifier for line state events
gpiolib: don't check the retval of get_direction() when registering a chip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of last-minute fixes.
Most of them are for ASoC, and the only one core fix is for reverting
the previous change, while the rest are all device-specific quirks and
fixes, which should be relatively safe to apply"
* tag 'sound-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: cs42l43: convert to SYSTEM_SLEEP_PM_OPS
ALSA: hda/realtek: Add mute LED quirk for HP Pavilion x360 14-dy1xxx
ASoC: codecs: wm0010: Fix error handling path in wm0010_spi_probe()
ASoC: rt722-sdca: add missing readable registers
ASoC: amd: yc: Support mic on another Lenovo ThinkPad E16 Gen 2 model
ASoC: cs42l43: Fix maximum ADC Volume
ASoC: ops: Consistently treat platform_max as control value
ASoC: rt1320: set wake_capable = 0 explicitly
ASoC: cs42l43: Add jack delay debounce after suspend
ASoC: tegra: Fix ADX S24_LE audio format
ASoC: codecs: wsa884x: report temps to hwmon in millidegree of Celsius
ASoC: Intel: sof_sdw: Fix unlikely uninitialized variable use in create_sdw_dailinks()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main one is a horrible macro fix for our TLB flushing code which
resulted in over-invalidation on the MMU notifier path.
Summary:
- Fix population of the vmemmap for regions of memory that are
smaller than a section (128 MiB)
- Fix range-based TLB over-invalidation when invoked via a MMU
notifier"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Fix mmu notifiers for range-based invalidates
arm64: mm: Populate vmemmap at the page level if not section aligned
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix the bootup of SEV-SNP enabled guests under VMware hypervisors"
* tag 'x86-urgent-2025-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vmware: Parse MP tables for SEV-SNP enabled guests under VMware hypervisors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a sleeping-while-atomic bug caused by a recent optimization
utilizing static keys that didn't consider that the
static_key_disable() call could be triggered in atomic context.
Revert the optimization"
* tag 'sched-urgent-2025-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/clock: Don't define sched_clock_irqtime as static key
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc locking fixes from Ingo Molnar:
- Restrict the Rust runtime from unintended access to dynamically
allocated LockClassKeys
- KernelDoc annotation fix
- Fix a lock ordering bug in semaphore::up(), related to trying to
printk() and wake up the console within critical sections
* tag 'locking-urgent-2025-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/semaphore: Use wake_q to wake up processes outside lock critical section
locking/rtmutex: Use the 'struct' keyword in kernel-doc comment
rust: lockdep: Remove support for dynamically allocated LockClassKeys
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fix from Ingo Molnar:
"Fix a Sparse false positive warning triggered by no_free_ptr()"
* tag 'core-urgent-2025-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
<linux/cleanup.h>: Allow the passing of both iomem and non-iomem pointers to no_free_ptr()
|
|
We just had a report of the assert for "btree in write buffer for
non-write buffer btree" popping during the 6.14 upgrade.
- 150TB filesystem, after a reboot the upgrade was able to continue from
where it left off, so no major damage.
But with 6.14 about to come out we want to get this tracked down asap,
and need more data if other users hit this.
Convert the BUG_ON() to an emergency read-only, and print out btree, the
key itself, and stack trace from the original write buffer update (which
did not have this check before).
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
I am no longer at Canonical and update with my personal email address.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Link: https://lore.kernel.org/r/20250314045732.389973-1-ike.pan@canonical.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
We have a central definition for this function since 2023, used by
a number of different parts of the kernel.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
