| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
FEC: Fix kernel panic in fec_set_mac_address.
ipv6: Fix default multicast hops setting.
net: ep93xx_eth stops receiving packets
drivers/net/phy: micrel phy driver
dm9601: fix phy/eeprom write routine
ppp_generic: handle non-linear skbs when passing them to pppd
ppp_generic: pull 2 bytes so that PPP_PROTO(skb) is valid
net: fix compile error due to double return type in SOCK_DEBUG
net/usb: initiate sync sequence in sierra_net.c driver
net/usb: remove default in Kconfig for sierra_net driver
r8169: Fix rtl8169_rx_interrupt()
e1000e: Fix oops caused by ASPM patch.
net/sb1250: register mdio bus in probe
sctp: Fix skb_over_panic resulting from multiple invalid parameter errors (CVE-2010-1173) (v4)
p54pci: fix bugs in p54p_check_tx_ring
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
ALSA: hda: Use olpc-xo-1_5 quirk for Toshiba Satellite P500-PSPGSC-01800T
ALSA: hda: Use olpc-xo-1_5 quirk for Toshiba Satellite Pro T130-15F
ALSA: hda - fix array indexing while creating inputs for Cirrus codecs
ALSA: es968: fix wrong PnP dma index
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - allow binding to button-only devices
Input: elantech - ignore high bits in the position coordinates
Input: elantech - allow forcing Elantech protocol
Input: elantech - fix firmware version check
Input: ati_remote - add some missing devices from lirc_atiusb
Input: eeti_ts - cancel pending work when going to suspend
Input: Add support of Synaptics Clickpad device
Revert "Input: ALPS - add signature for HP Pavilion dm3 laptops"
Input: psmouse - ignore parity error for basic protocols
|
|
The raid6 recovery code should immediately drop back to the optimized
synchronous path when a p+q dma resource is not available. Otherwise we
run the non-optimized/multi-pass async code in sync mode.
Verified with raid6test (NDISKS=255)
Applies to kernels >= 2.6.32.
Cc: <stable@kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Using explanation given by Ingo Molnar in the oprofile mailing list.
Suggested-by: Nick Black <dank@qemfd.net>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Black <dank@qemfd.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix a couple of inefficiencies and redundancies related to
have_tracepoints() and its use when checking whether to write
TRACE_INFO.
First, there's no need to use get_tracepoints_path() in
have_tracepoints() - we really just want the part that checks whether
any attributes correspondo to tracepoints.
Second, we really don't care about raw_samples per se - tracepoints
are always raw_samples. In any case, the have_tracepoints() check
should be sufficient to decide whether or not to write TRACE_INFO.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>,
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1273030770.6383.6.camel@tropicana>
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
call_sbin_request_key() creates a keyring and then attempts to insert a link to
the authorisation key into that keyring, but does so without holding a write
lock on the keyring semaphore.
It will normally get away with this because it hasn't told anyone that the
keyring exists yet. The new keyring, however, has had its serial number
published, which means it can be accessed directly by that handle.
This was found by a previous patch that adds RCU lockdep checks to the code
that reads the keyring payload pointer, which includes a check that the keyring
semaphore is actually locked.
Without this patch, the following command:
keyctl request2 user b a @s
will provoke the following lockdep warning is displayed in dmesg:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
security/keys/keyring.c:727 invoked rcu_dereference_check() without protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by keyctl/2076:
#0: (key_types_sem){.+.+.+}, at: [<ffffffff811a5b29>] key_type_lookup+0x1c/0x71
#1: (keyring_serialise_link_sem){+.+.+.}, at: [<ffffffff811a6d1e>] __key_link+0x4d/0x3c5
stack backtrace:
Pid: 2076, comm: keyctl Not tainted 2.6.34-rc6-cachefs #54
Call Trace:
[<ffffffff81051fdc>] lockdep_rcu_dereference+0xaa/0xb2
[<ffffffff811a6d1e>] ? __key_link+0x4d/0x3c5
[<ffffffff811a6e6f>] __key_link+0x19e/0x3c5
[<ffffffff811a5952>] ? __key_instantiate_and_link+0xb1/0xdc
[<ffffffff811a59bf>] ? key_instantiate_and_link+0x42/0x5f
[<ffffffff811aa0dc>] call_sbin_request_key+0xe7/0x33b
[<ffffffff8139376a>] ? mutex_unlock+0x9/0xb
[<ffffffff811a5952>] ? __key_instantiate_and_link+0xb1/0xdc
[<ffffffff811a59bf>] ? key_instantiate_and_link+0x42/0x5f
[<ffffffff811aa6fa>] ? request_key_auth_new+0x1c2/0x23c
[<ffffffff810aaf15>] ? cache_alloc_debugcheck_after+0x108/0x173
[<ffffffff811a9d00>] ? request_key_and_link+0x146/0x300
[<ffffffff810ac568>] ? kmem_cache_alloc+0xe1/0x118
[<ffffffff811a9e45>] request_key_and_link+0x28b/0x300
[<ffffffff811a89ac>] sys_request_key+0xf7/0x14a
[<ffffffff81052c0b>] ? trace_hardirqs_on_caller+0x10c/0x130
[<ffffffff81394fb9>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81001eeb>] system_call_fastpath+0x16/0x1b
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
The keyring key type code should use RCU dereference wrappers, even when it
holds the keyring's key semaphore.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
find_keyring_by_name() can gain access to a keyring that has had its reference
count reduced to zero, and is thus ready to be freed. This then allows the
dead keyring to be brought back into use whilst it is being destroyed.
The following timeline illustrates the process:
|(cleaner) (user)
|
| free_user(user) sys_keyctl()
| | |
| key_put(user->session_keyring) keyctl_get_keyring_ID()
| || //=> keyring->usage = 0 |
| |schedule_work(&key_cleanup_task) lookup_user_key()
| || |
| kmem_cache_free(,user) |
| . |[KEY_SPEC_USER_KEYRING]
| . install_user_keyrings()
| . ||
| key_cleanup() [<= worker_thread()] ||
| | ||
| [spin_lock(&key_serial_lock)] |[mutex_lock(&key_user_keyr..mutex)]
| | ||
| atomic_read() == 0 ||
| |{ rb_ease(&key->serial_node,) } ||
| | ||
| [spin_unlock(&key_serial_lock)] |find_keyring_by_name()
| | |||
| keyring_destroy(keyring) ||[read_lock(&keyring_name_lock)]
| || |||
| |[write_lock(&keyring_name_lock)] ||atomic_inc(&keyring->usage)
| |. ||| *** GET freeing keyring ***
| |. ||[read_unlock(&keyring_name_lock)]
| || ||
| |list_del() |[mutex_unlock(&key_user_k..mutex)]
| || |
| |[write_unlock(&keyring_name_lock)] ** INVALID keyring is returned **
| | .
| kmem_cache_free(,keyring) .
| .
| atomic_dec(&keyring->usage)
v *** DESTROYED ***
TIME
If CONFIG_SLUB_DEBUG=y then we may see the following message generated:
=============================================================================
BUG key_jar: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff880197a7e200-0xffff880197a7e200. First byte 0x6a instead of 0x6b
INFO: Allocated in key_alloc+0x10b/0x35f age=25 cpu=1 pid=5086
INFO: Freed in key_cleanup+0xd0/0xd5 age=12 cpu=1 pid=10
INFO: Slab 0xffffea000592cb90 objects=16 used=2 fp=0xffff880197a7e200 flags=0x200000000000c3
INFO: Object 0xffff880197a7e200 @offset=512 fp=0xffff880197a7e300
Bytes b4 0xffff880197a7e1f0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Object 0xffff880197a7e200: 6a 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b jkkkkkkkkkkkkkkk
Alternatively, we may see a system panic happen, such as:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
IP: [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
PGD 6b2b4067 PUD 6a80d067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/kernel/kexec_crash_loaded
CPU 1
...
Pid: 31245, comm: su Not tainted 2.6.34-rc5-nofixed-nodebug #2 D2089/PRIMERGY
RIP: 0010:[<ffffffff810e61a3>] [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
RSP: 0018:ffff88006af3bd98 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffff88007d19900b
RDX: 0000000100000000 RSI: 00000000000080d0 RDI: ffffffff81828430
RBP: ffffffff81828430 R08: ffff88000a293750 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000100000 R12: 00000000000080d0
R13: 00000000000080d0 R14: 0000000000000296 R15: ffffffff810f20ce
FS: 00007f97116bc700(0000) GS:ffff88000a280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000001 CR3: 000000006a91c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process su (pid: 31245, threadinfo ffff88006af3a000, task ffff8800374414c0)
Stack:
0000000512e0958e 0000000000008000 ffff880037f8d180 0000000000000001
0000000000000000 0000000000008001 ffff88007d199000 ffffffff810f20ce
0000000000008000 ffff88006af3be48 0000000000000024 ffffffff810face3
Call Trace:
[<ffffffff810f20ce>] ? get_empty_filp+0x70/0x12f
[<ffffffff810face3>] ? do_filp_open+0x145/0x590
[<ffffffff810ce208>] ? tlb_finish_mmu+0x2a/0x33
[<ffffffff810ce43c>] ? unmap_region+0xd3/0xe2
[<ffffffff810e4393>] ? virt_to_head_page+0x9/0x2d
[<ffffffff81103916>] ? alloc_fd+0x69/0x10e
[<ffffffff810ef4ed>] ? do_sys_open+0x56/0xfc
[<ffffffff81008a02>] ? system_call_fastpath+0x16/0x1b
Code: 0f 1f 44 00 00 49 89 c6 fa 66 0f 1f 44 00 00 65 4c 8b 04 25 60 e8 00 00 48 8b 45 00 49 01 c0 49 8b 18 48 85 db 74 0d 48 63 45 18 <48> 8b 04 03 49 89 00 eb 14 4c 89 f9 83 ca ff 44 89 e6 48 89 ef
RIP [<ffffffff810e61a3>] kmem_cache_alloc+0x5b/0xe9
This problem is that find_keyring_by_name does not confirm that the keyring is
valid before accepting it.
Skipping keyrings that have been reduced to a zero count seems the way to go.
To this end, use atomic_inc_not_zero() to increment the usage count and skip
the candidate keyring if that returns false.
The following script _may_ cause the bug to happen, but there's no guarantee
as the window of opportunity is small:
#!/bin/sh
LOOP=100000
USER=dummy_user
/bin/su -c "exit;" $USER || { /usr/sbin/adduser -m $USER; add=1; }
for ((i=0; i<LOOP; i++))
do
/bin/su -c "echo '$i' > /dev/null" $USER
done
(( add == 1 )) && /usr/sbin/userdel -r $USER
exit
Note that the nominated user must not be in use.
An alternative way of testing this may be:
for ((i=0; i<100000; i++))
do
keyctl session foo /bin/true || break
done >&/dev/null
as that uses a keyring named "foo" rather than relying on the user and
user-session named keyrings.
Reported-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
The first was always using the ->long_name, while the later used
->short_name if verbose was not set, resulting in the dso column to be
much wider than needed most of the time.
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add some delay to avoid reading CSR TXCOUNT too early after
updating it.
For more info about this HW glitch see:
http://lists.arm.linux.org.uk/lurker/message/20090325.150843.f515c02f.en.html
http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100129/10ba0f8b/attachment.el
http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100203/09cdb3b4/attachment.el
http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100203/08b5b249/attachment.el
First applied: "Fix soft lockup in at91 udc driver"
http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=5965
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
BugLink: https://launchpad.net/bugs/541802
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_cxt5045() for all Packard Bell models.
Reported-by: Valombre
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a quirk for all-in-one computer Dell Inspiron One 19 Touch to have proper
HP and Mic support.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We should disable irqs when we take the tu->qlock because it is used in
the irq handler. The only place that doesn't is
snd_timer_user_ccallback(). Most of the time snd_timer_user_ccallback()
is called with interrupts disabled but the the first ti->ccallback()
call in snd_timer_notify1() has interrupts enabled.
This was caught by lockdep which generates the following message:
> =================================
> [ INFO: inconsistent lock state ]
> 2.6.34-rc5 #5
> ---------------------------------
> inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
> dolphin/4003 [HC1[1]:SC0[0]:HE0:SE1] takes:
> (&(&tu->qlock)->rlock){?.+...}, at: [<f84ec472>] snd_timer_user_tinterrupt+0x28/0x132 [snd_timer]
> {HARDIRQ-ON-W} state was registered at:
> [<c1048de9>] __lock_acquire+0x654/0x1482
> [<c1049c73>] lock_acquire+0x5c/0x73
> [<c125ac3e>] _raw_spin_lock+0x25/0x34
> [<f84ec370>] snd_timer_user_ccallback+0x55/0x95 [snd_timer]
> [<f84ecc4b>] snd_timer_notify1+0x53/0xca [snd_timer]
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix memory corruption that sometimes result in kernel panic.
Signed-off-by: Mattias Walström <mattias@vmlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BugLink: https://launchpad.net/bugs/549267
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Richard Gagne
Tested-by: Richard Gagne
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://launchpad.net/bugs/573284
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Andy Couldrake <acouldrake@googlemail.com>
Tested-by: Andy Couldrake <acouldrake@googlemail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This fixes a problem where cards show up as only having a single mixer
element, suppressing all sound output.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/legacy: only enable load detection property on DVI-I
drm/radeon/kms: fix panel scaling adjusted mode setup
drivers/gpu/drm/drm_sysfs.c: sysfs files error handling
drivers/gpu/drm/radeon/radeon_atombios.c: range check issues
gpu: vga_switcheroo, fix lock imbalance
drivers/gpu/drm/drm_memory.c: fix check for end of loop
drivers/gpu/drm/via/via_video.c: fix off by one issue
drm/radeon/kms/agp The wrong AGP chipset can cause a NULL pointer dereference
drm/radeon/kms: r300 fix CS checker to allow zbuffer-only fastfill
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
powernow-k8: Fix frequency reporting
x86: Fix parse_reservetop() build failure on certain configs
x86: Fix NULL pointer access in irq_force_complete_move() for Xen guests
x86: Fix 'reservetop=' functionality
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
KEYS: Fix RCU handling in key_gc_keyring()
KEYS: Fix an RCU warning in the reading of user keys
|
|
key_gc_keyring() needs to either hold the RCU read lock or hold the keyring
semaphore if it's going to scan the keyring's list. Given that it only needs
to read the key list, and it's doing so under a spinlock, the RCU read lock is
the thing to use.
Furthermore, the RCU check added in e7b0a61b7929632d36cf052d9e2820ef0a9c1bfe is
incorrect as holding the spinlock on key_serial_lock is not grounds for
assuming a keyring's pointer list can be read safely. Instead, a simple
rcu_dereference() inside of the previously mentioned RCU read lock is what we
want.
Reported-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Fix an RCU warning in the reading of user keys:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
security/keys/user_defined.c:202 invoked rcu_dereference_check() without protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by keyctl/3637:
#0: (&key->sem){+++++.}, at: [<ffffffff811a80ae>] keyctl_read_key+0x9c/0xcf
stack backtrace:
Pid: 3637, comm: keyctl Not tainted 2.6.34-rc5-cachefs #18
Call Trace:
[<ffffffff81051f6c>] lockdep_rcu_dereference+0xaa/0xb2
[<ffffffff811aa55f>] user_read+0x47/0x91
[<ffffffff811a80be>] keyctl_read_key+0xac/0xcf
[<ffffffff811a8a06>] sys_keyctl+0x75/0xb7
[<ffffffff81001eeb>] system_call_fastpath+0x16/0x1b
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
DVI-D doesn't have analog. This matches the avivo behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This should duplicate exactly what the ddx does for both
legacy and avivo.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Avoid a gcc warning in ocfs2_wipe_inode().
ocfs2: Avoid direct write if we fall back to buffered I/O
ocfs2_dlmfs: Fix math error when reading LVB.
ocfs2: Update VFS inode's id info after reflink.
ocfs2: potential ERR_PTR dereference on error paths
ocfs2: Add directory entry later in ocfs2_symlink() and ocfs2_mknod()
ocfs2: use OCFS2_INODE_SKIP_ORPHAN_DIR in ocfs2_mknod error path
ocfs2: use OCFS2_INODE_SKIP_ORPHAN_DIR in ocfs2_symlink error path
ocfs2: add OCFS2_INODE_SKIP_ORPHAN_DIR flag and honor it in the inode wipe code
ocfs2: Reset status if we want to restart file extension.
ocfs2: Compute metaecc for superblocks during online resize.
ocfs2: Check the owner of a lockres inside the spinlock
ocfs2: one more warning fix in ocfs2_file_aio_write(), v2
ocfs2_dlmfs: User DLM_* when decoding file open flags.
|
|
Unregister and destroy the bdi in put_super, after mount is r/o, but before
put_anon_super releases the device name.
For symmetry, bdi_destroy in destroy_client (we bdi_init in create_client).
Only set s_bdi if bdi_register succeeds, since we use it to decide whether
to bdi_unregister.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
The x86_64 call_rwsem_wait() treats the active state counter part of the
R/W semaphore state as being 16-bit when it's actually 32-bit (it's half
of the 64-bit state). It should do "decl %edx" not "decw %dx".
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-core: Use per-adapter userspace device lists
i2c: Fix probing of FSC hardware monitoring chips
i2c-core: Erase pointer to clientdata on removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix resource leak in failure path of perf_event_open()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Fix RCU lockdep splat on freezer_fork path
rcu: Fix RCU lockdep splat in set_task_cpu on fork path
mutex: Don't spin when the owner CPU is offline or other weird cases
|
|
Now that the generic irq layer is performing the exact same remapping as
io_apic_renumber_irq we can kill this weird es7000 specific function.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-15-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
ACPI irq source overrides are allowed for the 16 isa irqs and are
allowed to map any gsi to any isa irq. A few motherboards have been
seen to take advantage of this and put the isa irqs on the 2nd or
3rd ioapic. This causes some problems, most notably the fact
that we can not use any gsi < 16.
To correct this move the gsis that are not isa irqs and have
a gsi number < 16 into the linux irq space just past gsi_end.
This is what the es7000 platform is doing today. Moving only the
low 16 gsis above the rest of the gsi's only penalizes weird
platforms, leaving sane acpi implementations with a 1-1 mapping
of gsis and irqs.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-14-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Use the global gsi_end value now that all ioapics have
valid gsi numbers instead of a combination of acpi_probe_gsi
and walking all of the ioapics and couting their number of
entries by hand if acpi_probe_gsi gave us an answer we did
not like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-13-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Now that all ioapics have valid gsi_base values use this to
accellerate pin_2_irq. In the case of acpi this also ensures
that pin_2_irq will compute the same irq value for an ioapic
pin as acpi will.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-12-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Now that all ioapic registration happens in mp_register_ioapic we can
move the calculation of nr_ioapic_registers there from enable_IO_APIC.
The number of ioapic registers is already calucated in mp_register_ioapic
so all that really needs to be done is to save the caluclated value
in nr_ioapic_registers.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-11-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Long ago MP_ioapic_info was the primary way of setting up our
ioapic data structures and mp_register_ioapic was a compatibility
shim for acpi code. Now the situation is reversed and
and mp_register_ioapic is the primary way of setting up our
ioapic data structures.
Keep the setting up of ioapic data structures uniform by
having mp_register_ioapic call mp_register_ioapic.
This changes a few fields:
- type: is now hardset to MP_IOAPIC but type had to
bey MP_IOAPIC or MP_ioapic_info would not have been called.
- flags: is now hard coded to MPC_APIC_USABLE.
We require flags to contain at least MPC_APIC_USEBLE in
MP_ioapic_info and we don't ever examine flags so dropping
a few flags that might possibly exist that we have never
used is harmless.
- apicaddr: Unchanged
- apicver: Read from the ioapic instead of using the cached
hardware value in the MP table. The real hardware value
will be more accurate.
- apicid: Now verified to be unique and changed if it is not.
If the BIOS got this right this is a noop. If the BIOS did
not fixing things appears to be the better solution.
This adds gsi_base and gsi_end values to our ioapics defined with
the mpatable, which will make our lives simpler later since
we can always assume gsi_base and gsi_end are valid.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-10-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Add the global variable gsi_end and teach mp_register_ioapic
to keep it uptodate as we add more ioapics into the system.
ioapics can only be added early in boot so the code that
runs later can treat gsi_end as a constant.
Remove the have hacks in sfi.c to second guess mp_register_ioapic
by keeping t's own running total of how many gsi's have been seen,
and instead use the gsi_end.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-9-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
This patches fixes the types of gsi_base and gsi_end values in
struct mp_ioapic_gsi, and the gsi parameter of mp_find_ioapic
and mp_find_ioapic_pin
A gsi is cannonically a u32, not an int.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-8-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
io_apic_redir_entries has a huge conceptual bug. It returns the maximum
redirection entry not the number of redirection entries. Which simply
does not match what the name of the function. This just caught me
and it caught Feng Tang, and Len Brown when they wrote sfi_parse_ioapic.
Modify io_apic_redir_entries to actually return the number of redirection
entries, and fix the callers so that they properly handle receiving the
number of the number of redirection table entries, instead of the
number of redirection table entries less one.
While the usage in sfi.c does not show up in this patch it is fixed
by virtue of the fact that io_apic_redir_entries now has the semantics
sfi_parse_ioapic most reasonably expects.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-7-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Multiple declarations of the same function in different headers
is a pain to maintain.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-6-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Remove the assumption that there is not an override for isa irq 0.
Instead lookup the gsi and from that lookup the ioapic and pin of each
isa irq indivdually.
In general this should not have any behavioural affect but in
perverse cases this gets all of the details correct, instead of
doing something weird.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-5-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Currently acpi_sci_ioapic_setup calls mp_override_legacy_irq with
bus_irq == gsi, which is wrong if we are comming from an override
Instead pass the bus_irq into acpi_sci_ioapic_setup.
This fix was inspired by a similar fix from:
Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-4-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Strictly speaking on x86 (where acpi is used) dev->irq must be
a dual i8259 irq input aka an isa irq. Therefore we should translate
that isa irq into a gsi before passing it to a function that
takes a gsi.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-3-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
In perverse acpi implementations the isa irqs are not identity mapped
to the first 16 gsi. Furthermore at least the extended interrupt
resource capability may return gsi's and not isa irqs. So since
what we get from acpi is a gsi teach acpi_get_overrride_irq to
operate on a gsi instead of an isa_irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-2-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
There are a number of cases where the current code makes the assumption
that isa irqs identity map to the first 16 acpi global system intereupts.
In most instances that assumption is correct as that is the required
behaviour in dual i8259 mode and the default behavior in ioapic mode.
However there are some systems out there that take advantage of acpis
interrupt remapping for the isa irqs to have a completely different
mapping of isa_irq to gsi.
Introduce acpi_isa_irq_to_gsi to perform this mapping explicitly in the
code that needs it. Initially this will be just the current assumed
identity mapping to ensure it's introduction does not cause regressions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-1-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Make it clear that event-list is a comma separated list of events.
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4B2F154C.2060503@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Commit 04de0816 (pcmcia: pcmcia_dev_present bugfix) broke the
deprecated ioctl layer. Fix it by getting rid of references to
unexisting fields.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
