| Age | Commit message (Collapse) | Author |
|---|
|
In commit 734643dfbdde ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59fda ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbdde ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The function graph tracer adds instrumentation that is required to trace
both entry and exit of a function. In particular the function graph
tracer updates the "return address" of a function in order to insert
a trace callback on function exit.
Kernel power management functions like cpu_suspend() are called
upon power down entry with functions called "finishers" that are in turn
called to trigger the power down sequence but they may not return to the
kernel through the normal return path.
When the core resumes from low-power it returns to the cpu_suspend()
function through the cpu_resume path, which leaves the trace stack frame
set-up by the function tracer in an incosistent state upon return to the
kernel when tracing is enabled.
This patch fixes the issue by pausing/resuming the function graph
tracer on the thread executing cpu_suspend() (ie the function call that
subsequently triggers the "suspend finishers"), so that the function graph
tracer state is kept consistent across functions that enter power down
states and never return by effectively disabling graph tracer while they
are executing.
Fixes: 819e50e25d0c ("arm64: Add ftrace support")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
SYNC in __switch_to() is a historic relic and not needed at all.
- In UP context it is obviously useless, why would we want to stall
the core for all updates to stack memory of t0 to complete before
loading kernel mode callee registers from t1 stack's memory.
- In SMP, there could be potential race in which outgoing task could
be concurrently picked for running on a different core, thus writes
to stack here need to be visible before the reads from stack on
other core. Peter confirmed that generic schedular already has needed
barriers (by way of rq lock) so there is no need for additional arch
barrier.
This came up when Noam was trying to replace this SYNC with EZChip
specific hardware thread scheduling instruction for their platform
support.
Link: http://lkml.kernel.org/r/20151102092654.GM17308@twins.programming.kicks-ass.net
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Cc: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
We try to convert the old way of of specifying fb tiling (obj->tiling)
into the new fb modifiers. We store the result in the passed in mode_cmd
structure. But that structure comes directly from the addfb2 ioctl, and
gets copied back out to userspace, which means we're clobbering the
modifiers that the user provided (all 0 since the DRM_MODE_FB_MODIFIERS
flag wasn't even set by the user). Hence if the user reuses the struct
for another addfb2, the ioctl will be rejected since it's now asking for
some modifiers w/o the flag set.
Fix the problem by making a copy of the user provided structure. We can
play any games we want with the copy.
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
...
Subtest basic-X-tiled: SUCCESS (0.001s)
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
Stack trace:
#0 [__igt_fail_assert+0x101]
#1 [pitch_tests+0x619]
#2 [__real_main426+0x2f]
#3 [main+0x23]
#4 [__libc_start_main+0xf0]
#5 [_start+0x29]
#6 [<unknown>+0x29]
Subtest framebuffer-vs-set-tiling failed.
**** DEBUG ****
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
**** END ****
Subtest framebuffer-vs-set-tiling: FAIL (0.003s)
...
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
Subtest framebuffer-vs-set-tiling: SUCCESS (0.000s)
Cc: stable@vger.kernel.org # v4.1+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 2a80eada326f ("drm/i915: Add fb format modifier support")
Testcase: igt/kms_addfb_basic/clobbered-modifier
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447261890-3960-1-git-send-email-ville.syrjala@linux.intel.com
|
|
Properly double the hdisplay/vdisplay timings that we use as the primary
plane size with stereo doubled modes. Otherwise the modeset gets
rejected on machines where the primary plane must be fullscreen, and on
the rest only the first eye would get a visible plane.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org #v3.19+
Fixes: 042652ed9599 ("drm/atomic-helper: implementatations for legacy interfaces")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447686157-29607-1-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_3d
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If an atomic update fails intel_crtc->atomic may have have some values left
from the last atomic check. One example is atomic->wait_for_vblank,
which results in spurious errors in kms_flip.
[ 1551.892708] ------------[ cut here ]------------
[ 1551.892721] WARNING: CPU: 3 PID: 4179 at ../drivers/gpu/drm/drm_irq.c:1199 drm_wait_one_vblank+0x197/0x1a0 [drm]()
[ 1551.892722] vblank not available on crtc 2, ret=-22
[ 1551.892751] Modules linked in: snd_hda_intel i915 drm_kms_helper drm
intel_gtt i2c_algo_bit cfbfillrect syscopyarea cfbimgblt sysfillrect
sysimgblt fb_sys_fops cfbcopyarea agpgart cfg80211 binfmt_misc
snd_hda_codec_hdmi intel_rapl iosf_mbi x86_pkg_temp_thermal coretemp
kvm_intel snd_hda_codec_realtek kvm snd_hda_codec_generic iTCO_wdt
aesni_intel aes_x86_64 glue_helper lrw snd_hda_codec gf128mul
ablk_helper cryptd snd_hwdep psmouse snd_hda_core pcspkr snd_pcm
snd_timer snd lpc_ich i2c_i801 mfd_core soundcore wmi evdev [last
unloaded: drm]
[ 1551.892753] CPU: 3 PID: 4179 Comm: kms_pipe_crc_ba Tainted: G U W 4.3.0-reg+ #6
[ 1551.892754] Hardware name: /DZ77BH-55K, BIOS BHZ7710H.86A.0100.2013.0517.0942 05/17/2013
[ 1551.892758] ffffffffa03128d8 ffff8800cec73890 ffffffff812c0f3c ffff8800cec738d8
[ 1551.892760] ffff8800cec738c8 ffffffff8104ff36 ffff880116ae2290 0000000000000002
[ 1551.892762] ffff8800d39fcda0 ffff8800d038b4d0 ffff8800d42b5550 ffff8800cec73928
[ 1551.892763] Call Trace:
[ 1551.892768] [<ffffffff812c0f3c>] dump_stack+0x4e/0x82
[ 1551.892771] [<ffffffff8104ff36>] warn_slowpath_common+0x86/0xc0
[ 1551.892773] [<ffffffff8104ffbc>] warn_slowpath_fmt+0x4c/0x50
[ 1551.892781] [<ffffffffa02e6708>] ? drm_vblank_get+0x78/0xd0 [drm]
[ 1551.892787] [<ffffffffa02e6d47>] drm_wait_one_vblank+0x197/0x1a0 [drm]
[ 1551.892813] [<ffffffffa03d052f>] intel_post_plane_update+0xef/0x120 [i915]
[ 1551.892832] [<ffffffffa03d11d2>] intel_atomic_commit+0x4c2/0x1600 [i915]
[ 1551.892862] [<ffffffffa02ff0c7>] ? drm_atomic_check_only+0x147/0x5e0 [drm]
[ 1551.892872] [<ffffffffa02feeb7>] ? drm_atomic_add_affected_connectors+0x27/0xf0 [drm]
[ 1551.892881] [<ffffffffa02ff597>] drm_atomic_commit+0x37/0x60 [drm]
[ 1551.892887] [<ffffffffa034301a>] restore_fbdev_mode+0x28a/0x2c0 [drm_kms_helper]
[ 1551.892895] [<ffffffffa0345253>] drm_fb_helper_restore_fbdev_mode_unlocked+0x33/0x80 [drm_kms_helper]
[ 1551.892900] [<ffffffffa03452cd>] drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper]
[ 1551.892920] [<ffffffffa03e7a9a>] intel_fbdev_set_par+0x1a/0x60 [i915]
[ 1551.892923] [<ffffffff8131a5a7>] fb_set_var+0x1a7/0x3f0
[ 1551.892927] [<ffffffff8109732f>] ? trace_hardirqs_on_caller+0x12f/0x1c0
[ 1551.892931] [<ffffffff81314f32>] fbcon_blank+0x212/0x2f0
[ 1551.892935] [<ffffffff81373f4a>] do_unblank_screen+0xba/0x1d0
[ 1551.892937] [<ffffffff8136b725>] vt_ioctl+0x13d5/0x1450
[ 1551.892940] [<ffffffff8107cdd1>] ? preempt_count_sub+0x41/0x50
[ 1551.892943] [<ffffffff8135d8a3>] tty_ioctl+0x423/0xe30
[ 1551.892947] [<ffffffff8119f721>] do_vfs_ioctl+0x301/0x560
[ 1551.892949] [<ffffffff8119b1e3>] ? putname+0x53/0x60
[ 1551.892952] [<ffffffff811ab376>] ? __fget_light+0x66/0x90
[ 1551.892955] [<ffffffff8119f9f9>] SyS_ioctl+0x79/0x90
[ 1551.892958] [<ffffffff81552e97>] entry_SYSCALL_64_fastpath+0x12/0x6f
[ 1551.892961] ---[ end trace 3e764d4b6628c91c ]---
Testcase: kms_flip
Reported-and-tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org #v4.3
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/5649C2BA.6080300@mblankhorst.nl
|
|
When using EOImode==1, we may mark interrupts as being forwarded
to a virtual machine. In that case, the interrupt is left active
while being passed to the VM.
If we suspend the system before the VM has deactivated the interrupt,
the active state will be lost (which may be very annoying, as this
may result in spurious interrupts and a confused guest).
To avoid this, save and restore the active state together with the
rest of the GIC registers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When restoring the GIC state (after a suspend/resume cycle,
for example), the driver directly writes the 'enabled' state
it has saved by accessing GICD_ISENABLERn, which performs
an OR operation between the value present in the register
and the value we write.
If whatever code that has run before we reentered the kernel
has enabled an interrupt that was previously disabled, we won't
restore that disabled state.
Making sure we first clear the register (by writting to
GICD_ICENABLERn) before restoring the enabled state.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When booting a GIC/GICv3 based system, we have no idea what
state the firmware (or previous kernel in the case of kexec)
has left the GIC, and some interrupts may still be active.
In order to garantee that we have a clean state, make sure
the active bits are cleared at init time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
including ptrace.h brings a definition of BITS_PER_PAGE into device
drivers and cause a build warning in allmodconfig builds:
drivers/block/drbd/drbd_bitmap.c:482:0: warning: "BITS_PER_PAGE" redefined
#define BITS_PER_PAGE (1UL << (PAGE_SHIFT + 3))
This uses a slightly different way to express current_pt_regs()
that avoids the use of the header and gets away with the already
included asm/ptrace.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Including linux/acpi.h from asm/dma-mapping.h causes tons of compile-time
warnings, e.g.
drivers/isdn/mISDN/dsp_ecdis.h:43:0: warning: "FALSE" redefined
drivers/isdn/mISDN/dsp_ecdis.h:44:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:62:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:63:0: warning: "FALSE" redefined
However, it looks like the dependency should not even there as
I do not see why __generic_dma_ops() cares about whether we have
an ACPI based system or not.
The current behavior is to fall back to the global dma_ops when
a device has not set its own dma_ops, but only for DT based systems.
This seems dangerous, as a random device might have different
requirements regarding IOMMU or coherency, so we should really
never have that fallback and just forbid DMA when we have not
initialized DMA for a device.
This removes the global dma_ops variable and the special-casing
for ACPI, and just returns the dma ops that got set for the
device, or the dummy_dma_ops if none were present.
The original code has apparently been copied from arm32 where we
rely on it for ISA devices things like the floppy controller, but
we should have no such devices on ARM64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[catalin.marinas@arm.com: removed acpi_disabled check in arch_setup_dma_ops()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When booting a 64k pages kernel that is built with CONFIG_DEBUG_RODATA
and resides at an offset that is not a multiple of 512 MB, the rounding
that occurs in __map_memblock() and fixup_executable() results in
incorrect regions being mapped.
The following snippet from /sys/kernel/debug/kernel_page_tables shows
how, when the kernel is loaded 2 MB above the base of DRAM at 0x40000000,
the first 2 MB of memory (which may be inaccessible from non-secure EL1
or just reserved by the firmware) is inadvertently mapped into the end of
the module region.
---[ Modules start ]---
0xfffffdffffe00000-0xfffffe0000000000 2M RW NX ... UXN MEM/NORMAL
---[ Modules end ]---
---[ Kernel Mapping ]---
0xfffffe0000000000-0xfffffe0000090000 576K RW NX ... UXN MEM/NORMAL
0xfffffe0000090000-0xfffffe0000200000 1472K ro x ... UXN MEM/NORMAL
0xfffffe0000200000-0xfffffe0000800000 6M ro x ... UXN MEM/NORMAL
0xfffffe0000800000-0xfffffe0000810000 64K ro x ... UXN MEM/NORMAL
0xfffffe0000810000-0xfffffe0000a00000 1984K RW NX ... UXN MEM/NORMAL
0xfffffe0000a00000-0xfffffe00ffe00000 4084M RW NX ... UXN MEM/NORMAL
The same issue is likely to occur on 16k pages kernels whose load
address is not a multiple of 32 MB (i.e., SECTION_SIZE). So round to
SWAPPER_BLOCK_SIZE instead of SECTION_SIZE.
Fixes: da141706aea5 ("arm64: add better page protections to arm64")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Update Josh's entries about NAND and ISI drivers.
Thanks for your work with Atmel Josh!
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Josh Wu <rainyfeeling@outlook.com>
|
|
Don't touch plane->old_fb/fb without having the right locks held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-6-git-send-email-maarten.lankhorst@ubuntu.com
|
|
Don't touch plane->old_fb/fb without having the right locks held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-5-git-send-email-maarten.lankhorst@ubuntu.com
|
|
This is useful for all the boilerplate code about cleaning old_fb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-4-git-send-email-maarten.lankhorst@ubuntu.com
|
|
plane_mask should be cleared inside the retry loop, because it gets
reset on every retry. Without this fix the plane->fb refcounting might
get out of sync on retries, resulting in either leaked memory or
use-after-free.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org #v4.3
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-3-git-send-email-maarten.lankhorst@ubuntu.com
|
|
legacy_cursor_update was being set in restore_fbdev_mode_atomic which was
probably unintended. Fix this by only setting it in the function that needs it.
This oversight was introduced in
commit bbb1e52402b2a288b09ae37e8182599931c7e9df
Author: Rob Clark <robdclark@gmail.com>
Date: Tue Aug 25 15:35:58 2015 -0400
drm/fb-helper: atomic restore_fbdev_mode()...
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: checkpatch fix]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-2-git-send-email-maarten.lankhorst@ubuntu.com
|
|
While dax pmd mappings are functional in the nominal path they trigger
kernel crashes in the following paths:
BUG: unable to handle kernel paging request at ffffea0004098000
IP: [<ffffffff812362f7>] follow_trans_huge_pmd+0x117/0x3b0
[..]
Call Trace:
[<ffffffff811f6573>] follow_page_mask+0x2d3/0x380
[<ffffffff811f6708>] __get_user_pages+0xe8/0x6f0
[<ffffffff811f7045>] get_user_pages_unlocked+0x165/0x1e0
[<ffffffff8106f5b1>] get_user_pages_fast+0xa1/0x1b0
kernel BUG at arch/x86/mm/gup.c:131!
[..]
Call Trace:
[<ffffffff8106f34c>] gup_pud_range+0x1bc/0x220
[<ffffffff8106f634>] get_user_pages_fast+0x124/0x1b0
BUG: unable to handle kernel paging request at ffffea0004088000
IP: [<ffffffff81235f49>] copy_huge_pmd+0x159/0x350
[..]
Call Trace:
[<ffffffff811fad3c>] copy_page_range+0x34c/0x9f0
[<ffffffff810a0daf>] copy_process+0x1b7f/0x1e10
[<ffffffff810a11c1>] _do_fork+0x91/0x590
All of these paths are interpreting a dax pmd mapping as a transparent
huge page and making the assumption that the pfn is covered by the
memmap, i.e. that the pfn has an associated struct page. PTE mappings
do not suffer the same fate since they have the _PAGE_SPECIAL flag to
cause the gup path to fault. We can do something similar for the PMD
path, or otherwise defer pmd support for cases where a struct page is
available. For now, 4.4-rc and -stable need to disable dax pmd support
by default.
For development the "depends on BROKEN" line can be removed from
CONFIG_FS_DAX_PMD.
Cc: <stable@vger.kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Correct typo in tools/testing/selftests/futex/README.
Signed-off-by: Wei Jiangang <weijg.fnst@cn.fujitsu.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 102f4d900c9c8f5e ("FS-Cache: Handle a write to the page immediately beyond the EOF marker")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The Broadcom NAND driver is used by many different groups at Broadcom
now, so use the same mailing-list we use for other areas of the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Given that INTUOSHT < BAMBOO_PT
features->type >= INTUOSHT || features->type <= BAMBOO_PT
condition is always true, and therefore device_type is under certain
circumstances wrongly set with WACOM_DEVICETYPE_PAD bit set.
Fix the condition so that it actually represents the range as intended.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The acpi_ec_delete_query() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit 3349fb64b292 (ACPI / SBS: Add 5 us delay to fix SBS
hangs on MacBook), since the delay introduced by it is not necessary
any more after commit add68d6aa9e2 (ACPI / SMBus: Fix boot stalls /
high CPU caused by reentrant code).
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently blk_insert_flush() just adds flush request to q->queue_head
when flush is not required. That completely bypasses IO scheduler so
e.g. CFQ can be idling waiting for new request to arrive and will idle
through the whole window unnecessarily. Luckily this only happens in
rare cases as usually checks in generic_make_request_checks() clear
FLUSH and FUA flags early if they are not needed.
When no flushing is actually required, we can easily fix the problem by
properly queueing the request through the IO scheduler. Ideally IO
scheduler should be also made aware of requests queued via
blk_flush_queue_rq(). However inserting flush request through IO
scheduler can have unwanted side-effects since due to flush batching
delaying the flush request in IO scheduler will delay all flush requests
possibly coming from other processes. So we keep adding the request
directly to q->queue_head.
Signed-off-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In the SBS initialisation, a reentrant call to wait_event_timeout()
causes an intermittent boot stall of several minutes usually following
the "Switching to clocksource tsc" message. Another symptom of this bug
is high CPU usage from programs (Firefox, upowerd) querying the battery
state. This is caused by:
1. drivers/acpi/sbshc.c wait_transaction_complete() calls
wait_event_timeout():
if (wait_event_timeout(hc->wait, smb_check_done(hc),
msecs_to_jiffies(timeout)))
2. ___wait_event sets task state to uninterruptible
3. ___wait_event calls the "condition" smb_check_done()
4. smb_check_done (sbshc.c) calls through to ec_read() in
drivers/acpi/ec.c
5. ec_guard() is reached which calls wait_event_timeout()
if (wait_event_timeout(ec->wait,
ec_transaction_completed(ec),
guard))
ie. wait_event_timeout() is being called again inside evaluation of
the previous wait_event_timeout() condition
5. The EC IRQ handler calls wake_up() and wakes up the sleeping task in
ec_guard()
6. The task is now in state running even though the wait "condition" is
still being evaluated
7. The "condition" check returns false so ___wait_event calls
schedule_timeout()
8. Since the task state is running, the scheduler immediately schedules
it again
9. This loop usually repeats for around 250 seconds even though the
original wait_event_timeout was only 1000ms.
The timeout is incorrect because each call to schedule_timeout()
usually returns immediately, taking less than 1ms, so the jiffies
timeout counter is not decremented. The task is now stuck in a
running state, and so is highly likely to be immediately
rescheduled, which takes less than a jiffy. The loop will never exit
if all schedule_timeout() calls take less than a jiffy.
Fix this by replacing SMBus reads in the wait_event_timeout condition
with checks of a boolean value that is updated by the EC query handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=107191
Link: https://lkml.org/lkml/2015/11/6/776
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for registering as a LightNVM device. This allows us to
evaluate the performance of the LightNVM subsystem.
In /drivers/Makefile, LightNVM is moved above block device drivers
to make sure that the LightNVM media managers have been initialized
before drivers under /drivers/block are initialized.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Fix by Jens Axboe to remove unneeded slab cache and the following
memory leak.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
To make the intention clearer, use list_{first,prev,next}_entry
instead of list_entry.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This prevents outstanding IOs to be sent for completion to target after
the target has been removed. The flow is now: stop new IOs > cleanup
queue > remove target.
Signed-off-by: Javier Gonzalez <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The specification was updated the remove the double word just after
number of configuration groups and capabilities. Update the identify
structure to reflect it.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The ppa format was not copied from the NVMe specific ppa format to the
lightnvm specific ppa format. This led to the ppa format not being
communicated to the layers above.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The linear and device specific address modes can be replaced with a
simple offset and bit length conversion that is generic across all
devices.
This both simplifies the specification and removes the special case for
qemu nvme, that previously relied on the linear address mapping.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Both the nvm_register and nvm_init does a kfree(dev) on error. Make sure
to only free it once.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We register with nvm_devices when there registration can still fail.
Move the final registration at the end of the nvm_register function
to make sure we are fully registered when added to the nvm_devices list.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Only NAND flash with SLC and MLC is supported. Make sure to not try to
initialize TLC memory or other non-volatile memory types.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The nvm_id, nvm_id_group and nvm_addr_format data structures contain
reserved attributes. They are unused by media managers and targets.
Remove them.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The mccap field is required for I/O command option support. It defines the
following flash access modes:
* SLC mode
* Erase/Program Suspension
* Scramble On/Off
* Encryption
It is slotted in between mpos and cpar, changing the offset for
cpar as well.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A single 8 bit and 16 bit reserve field were inserted in the
specification to align fields appropriately. Reflect this in the
identify group structure.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The specification was changed to reflect a multi-value bad block table.
Instead of bit-based bad block table, the bad block table now allows
eight bad block categories. Currently four are defined:
* Factory bad blocks
* Grown bad blocks
* Device-side reserved blocks
* Host-side reserved blocks
The factory and grown bad blocks are the regular bad blocks. The
reserved blocks are either for internal use or external use. In
particular, the device-side reserved blocks allows the host to
bootstrap from a limited number of flash blocks. Reducing the flash
blocks to scan upon super block initialization.
Support for both get bad block table and set bad block table is added.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The max_phys_sect variable is defined as a char. We do a boundary check
to maximally allow 256 physical page descriptors per command. As we are
not indexing from zero. This expression is always false. Bump the
max_phys_sect to an unsigned int to support the range check.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check that IRQ number passed to dev_pm_set_wake_irq() and
dev_pm_set_dedicated_wake_irq() is valid (not negative) before
accepting it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
Otherwise debugging locked up processes isn't possible.
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
|
|
* pm-tools:
x86: remove unused definition of MSR_NHM_PLATFORM_INFO
tools/power turbostat: use new name for MSR_PLATFORM_INFO
|
