| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-11-20
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5e: Fix set vf link state error flow')
For -stable v4.14
('net/mlxfw: Verify FSM error code translation doesn't exceed array size')
For -stable v4.19
('net/mlx5: Fix auto group size calculation')
For -stable v5.3
('net/mlx5e: Fix error flow cleanup in mlx5e_tc_tun_create_header_ipv4/6')
('net/mlx5e: Do not use non-EXT link modes in EXT mode')
('net/mlx5: Update the list of the PCI supported devices')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).
In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.
The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.
Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.
Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stefan Wahren says:
====================
net: qca_spi: Fix receive and reset issues
This small patch series fixes two major issues in the SPI driver for the
QCA700x.
It has been tested on a Charge Control C 300 (NXP i.MX6ULL +
2x QCA7000).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving many or larger packets, e.g. when doing a file download,
it was observed that the read buffer size register reports up to 4 bytes
more than the current define allows in the check.
If this is the case, then no data transfer is initiated to receive the
packets (and thus to empty the buffer) which results in a stall of the
interface.
These 4 bytes are a hardware generated frame length which is prepended
to the actual frame, thus we have to respect it during our check.
Fixes: 026b907d58c4 ("net: qca_spi: Add available buffer space verification")
Signed-off-by: Michael Heimpold <michael.heimpold@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Juliet Kim says:
====================
Support both XIVE and XICS modes in ibmvnic
This series aims to support both XICS and XIVE with avoiding
a regression in behavior when a system runs in XICS mode.
Patch 1 reverts commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”)
Patch 2 Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reversion of commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Array mlxfw_fsm_state_err_str contains value to string translation, when
values are provided by mlxfw_dev. If value is larger than
MLXFW_FSM_STATE_ERR_MAX, return "unknown error" as expected instead of
reading an address than exceed array size.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the upcoming ConnectX-6 LX device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Shani Shapp <shanish@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Fixes: f0d22d187473 ("net/mlx5_core: Introduce flow steering autogrouped flow table")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Device that doesn't support IP-in-IP offloads has to filter csum and gso
offload support, otherwise kernel will conclude that device is capable of
offloading csum and gso for IP-in-IP tunnels and that might result in
IP-in-IP tunnel not functioning.
Fixes: 25948b87dda2 ("net/mlx5e: Support TSO and TX checksum offloads for IP-in-IP")
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On some old Firmwares, connector type value was not supported, and value
read from FW was 0. For those, driver used link mode in order to set
connector type in link_ksetting.
After FW exposed the connector type, driver translated the value to ethtool
definitions. However, as 0 is a valid value, before returning PORT_OTHER,
driver run the check of link mode in order to maintain backward
compatibility.
Cited patch added support to EXT mode. With both features (connector type
and EXT link modes) ,if connector_type read from FW is 0 and EXT mode is
set, driver mistakenly compare EXT link modes to non-EXT link mode.
Fixed that by skipping this comparison if we are in EXT mode, as connector
type value is valid in this scenario.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before this commit the ndo always returned success.
Fix that.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When an ste hash table has too many collision we enlarge it
to a bigger hash table (rehash). Rehashing collision improvement
depends on the bytemask value. The more 1 bits we have in bytemask
means better spreading in the table.
Without this fix tables can grow in size without providing any
improvement which can lead to memory depletion and failures.
This patch will limit table rehash to reduce memory and improve
the performance.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The byte mask fields affect on the hash index distribution,
when the byte mask is zero, the hash calculation will always
be equal to the same index.
To avoid unneeded rehash of hash tables mark the table to skip
rehash.
This is needed by the next patch which will limit table rehash
to reduce memory consumption.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When creating a CQ, the CPU id is used for the vector value.
This would fail in-case the CPU id was higher than the maximum
vector value.
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Mirred action parsing code in parse_tc_fdb_actions() first checks if
out_dev has same parent id, and only verifies that there is a pending encap
action that was parsed before. Recent change in vxlan module made function
netdev_port_same_parent_id() to return true when called for mlx5 eswitch
representor and vxlan device created explicitly on mlx5 representor
device (vxlan devices created with "external" flag without explicitly
specifying parent interface are not affected). With call to
netdev_port_same_parent_id() returning true, incorrect code path is chosen
and encap rules fail to offload because vxlan dev is not a valid eswitch
forwarding dev. Dmesg log of error:
[ 1784.389797] devices ens1f0_0 vxlan1 not on same switch HW, can't offload forwarding
In order to fix the issue, rearrange conditional in parse_tc_fdb_actions()
to check for pending encap action before checking if out_dev has the same
parent id.
Fixes: 0ce1822c2a08 ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current code uses the old method of prio encoding in
flow_cls_common_offload. Fix to follow the changes introduced in
commit ef01adae0e43 ("net: sched: use major priority number as hardware priority").
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Be sure to release the neighbour in case of failures after successful
route lookup.
Fixes: 101f4de9dd52 ("net/mlx5e: Move TC tunnel offloading code to separate source file")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-11-20
please apply two late qeth fixes to your net tree.
The first fixes a deadlock that can occur if a qeth device is set
offline while in the middle of processing deferred HW events.
The second patch converts the return value of an error path to
use -EIO, so that it can be passed back to userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.
Fixes: 54daaca7024d ("s390/qeth: cancel cmd on early error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.
Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.
Fixes: c0a2e4d10d93 ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c802f0
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kobject_init_and_add takes reference even when it fails. This has
to be given up by the caller in error handling. Otherwise memory
allocated by kobject_init_and_add is never freed. Originally found
by Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880679f8b08 (size 8):
comm "netdev_register", pid 269, jiffies 4294693094 (age 12.132s)
hex dump (first 8 bytes):
72 78 2d 30 00 36 20 d4 rx-0.6 .
backtrace:
[<000000008c93818e>] __kmalloc_track_caller+0x16e/0x290
[<000000001f2e4e49>] kvasprintf+0xb1/0x140
[<000000007f313394>] kvasprintf_const+0x56/0x160
[<00000000aeca11c8>] kobject_set_name_vargs+0x5b/0x140
[<0000000073a0367c>] kobject_init_and_add+0xd8/0x170
[<0000000088838e4b>] net_rx_queue_update_kobjects+0x152/0x560
[<000000006be5f104>] netdev_register_kobject+0x210/0x380
[<00000000e31dab9d>] register_netdevice+0xa1b/0xf00
[<00000000f68b2465>] __tun_chr_ioctl+0x20d5/0x3dd0
[<000000004c50599f>] tun_chr_ioctl+0x2f/0x40
[<00000000bbd4c317>] do_vfs_ioctl+0x1c7/0x1510
[<00000000d4c59e8f>] ksys_ioctl+0x99/0xb0
[<00000000946aea81>] __x64_sys_ioctl+0x78/0xb0
[<0000000038d946e5>] do_syscall_64+0x16f/0x580
[<00000000e0aa5d8f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000285b3d1a>] 0xffffffffffffffff
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is safer and simpler to drop the uaccess assembly macros in favour of
inline C functions. Although this bloats the Image size slightly, it
aligns our user copy routines with '{get,put}_user()' and generally
makes the code a lot easier to reason about.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: tweaked commit message and changed temporary variable names]
Signed-off-by: Will Deacon <will@kernel.org>
|
|
A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.
For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.
For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.
For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.
As Pavel explains:
| I was able to reproduce memory corruption problem on Broadcom's SoC
| ARMv8-A like this:
|
| Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
| stack is accessed and copied.
|
| The test program performed the following on every CPU and forking
| many processes:
|
| unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
| MAP_SHARED | MAP_ANONYMOUS, -1, 0);
| map[0] = getpid();
| sched_yield();
| if (map[0] != getpid()) {
| fprintf(stderr, "Corruption detected!");
| }
| munmap(map, PAGE_SIZE);
|
| From time to time I was getting map[0] to contain pid for a
| different process.
Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 338d4f49d6f7 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Linux-next commit titled "perf/core: Optimize perf_init_event()"
changed the semantics of PMU device driver registration.
It was done to speed up the lookup/handling of PMU device driver
specific events. It also enforces that only one PMU device
driver will be registered of type PERF_EVENT_RAW.
This change added these line in function perf_pmu_register():
...
+ ret = idr_alloc(&pmu_idr, pmu, max, 0, GFP_KERNEL);
+ if (ret < 0)
goto free_pdc;
+
+ WARN_ON(type >= 0 && ret != type);
The warn_on generates a message. We have 3 PMU device drivers,
each registered as type PERF_TYPE_RAW.
The cf_diag device driver (arch/s390/kernel/perf_cpumf_cf_diag.c)
always hits the WARN_ON because it is the second PMU device driver
(after sampling device driver arch/s390/kernel/perf_cpumf_sf.c)
which is registered as type 4 (PERF_TYPE_RAW).
So when the sampling device driver is registered, ret has value 4.
When cf_diag device driver is registered with type 4,
ret has value of 5 and WARN_ON fires.
Adjust the PMU device drivers for s390 to support the new
semantics required by perf_pmu_register().
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Since commit 1313cc2bd8f6 ("kvm: mmu: Add guest_mode to kvm_mmu_page_role"),
guest_mode was added to mmu-role and therefore if L0 use EPT, it will
always run L1 and L2 with different EPTP. i.e. EPTP01!=EPTP02.
Because TLB entries are tagged with EP4TA, KVM can assume
TLB entries populated while running L2 are tagged differently
than TLB entries populated while running L1.
Therefore, update nested_has_guest_tlb_tag() to consider if
L0 use EPT instead of if L1 use EPT.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The function is only used in kvm.ko module.
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When L1 guest uses 5-level paging, it fails vm-entry to L2 due to
invalid host-state. It needs to add CR4_LA57 bit to nested CR4_FIXED1
MSR.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Not zeroing the bitmap used for identifying the destination vCPUs for an
IOAPIC scan request in fixed delivery mode could lead to waking up unwanted
vCPUs. This patch zeroes the vCPU bitmap before passing it to
kvm_bitmap_or_dest_vcpus(), which is responsible for setting the bitmap
with the bits corresponding to the destination vCPUs.
Fixes: 7ee30bc132c6("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If an SMT capable system is not IPL'ed from the first CPU the setup of
the physical to logical CPU mapping is broken: the IPL core gets CPU
number 0, but then the next core gets CPU number 1. Correct would be
that all SMT threads of CPU 0 get the subsequent logical CPU numbers.
This is important since a lot of code (like e.g. the CPU topology
code) assumes that CPU maps are setup like this. If the mapping is
broken the system will not IPL due to broken topology masks:
[ 1.716341] BUG: arch topology broken
[ 1.716342] the SMT domain not a subset of the MC domain
[ 1.716343] BUG: arch topology broken
[ 1.716344] the MC domain not a subset of the BOOK domain
This scenario can usually not happen since LPARs are always IPL'ed
from CPU 0 and also re-IPL is intiated from CPU 0. However older
kernels did initiate re-IPL on an arbitrary CPU. If therefore a re-IPL
from an old kernel into a new kernel is initiated this may lead to
crash.
Fix this by setting up the physical to logical CPU mapping correctly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
vdso_per_cpu_data lowcore value is only needed for fully functional
exception handlers, which are activated in setup_lowcore_dat_off. The
same function does init vdso_per_cpu_data via vdso_alloc_boot_cpu.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently if the kernel is built with CONFIG_TRACE_IRQFLAGS and KASAN
and used as crash kernel it crashes itself due to
trace_hardirqs_off/trace_hardirqs_on being called with DAT off. This
happens because trace_hardirqs_off/trace_hardirqs_on are instrumented and
kasan code tries to perform access to shadow memory to validate memory
accesses. Kasan shadow memory is populated with vmemmap, so all accesses
require DAT on.
memcpy_real could be called with DAT on or off (with kasan enabled DAT
is set even before early code is executed).
Make sure that trace_hardirqs_off/trace_hardirqs_on are called with DAT
on and only actual __memcpy_real is called with DAT off.
Also annotate __memcpy_real and _memcpy_real with __no_sanitize_address
to avoid further problems due to switching DAT off.
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
s390_crypto_shash_parmsize() return type is int, it
should not be stored in a unsigned variable, which
compared with zero.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3c2eb6b76cab ("s390/crypto: Support for SHA3 via CPACF (MSA6)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Joerg Schmidbauer <jschmidb@linux.vnet.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
pidfd_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.
Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.
Fixes: b53b0b9d9a61 ("pidfd: add polling support")
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org # 5.3
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191120003320.31138-1-luc.vanoostenryck@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
|
|
Switching cpufreq drivers (or switching operation modes of the
intel_pstate driver from "active" to "passive" and vice versa)
does not work on some x86 systems with ACPI after commit
3000ce3c52f8 ("cpufreq: Use per-policy frequency QoS"), because
the ACPI _PPC and thermal code uses the same frequency QoS request
object for a given CPU every time a cpufreq driver is registered
and freq_qos_remove_request() does not invalidate the request after
removing it from its QoS list, so freq_qos_add_request() complains
and fails when that request is passed to it again.
Fix the issue by modifying freq_qos_remove_request() to clear the qos
and type fields of the frequency request pointed to by its argument
after removing it from its QoS list so as to invalidate it.
Fixes: 3000ce3c52f8 ("cpufreq: Use per-policy frequency QoS")
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Instead of multiplying by page order, virtio balloon divided by page
order. The result is that it can return 0 if there are a bit less
than MAX_ORDER - 1 pages in use, and then shrinker scan won't be called.
Cc: stable@vger.kernel.org
Fixes: 71994620bb25 ("virtio_balloon: replace oom notifier with shrinker")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
|
|
virtio_balloon_shrinker_scan should return number of system pages freed,
but because it's calling functions that deal with balloon pages, it gets
confused and sometimes returns the number of balloon pages.
It does not matter practically as the exact number isn't
used, but it seems better to be consistent in case someone
starts using this API.
Further, if we ever tried to iteratively leak pages as
virtio_balloon_shrinker_scan tries to do, we'd run into issues - this is
because freed_pages was accumulating total freed pages, but was also
subtracted on each iteration from pages_to_free, which can result in
either leaking less memory than we were supposed to free, or more if
pages_to_free underruns.
On a system with 4K pages we are lucky that we are never asked to leak
more than 128 pages while we can leak up to 256 at a time,
but it looks like a real issue for systems with page size != 4K.
Fixes: 71994620bb25 ("virtio_balloon: replace oom notifier with shrinker")
Reported-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 075e238d12c21c8bde700d21fb48be7a3aa80194.
Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.
This patch fixes this wrong bit mask.
Fixes: 2336f19d7892 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3eddb4 ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when configuring act_pedit rules, the number of keys is validated only on
addition of a new entry. This is not sufficient to avoid hitting a WARN()
in the traffic path: for example, it is possible to replace a valid entry
with a new one having 0 extended keys, thus causing splats in dmesg like:
pedit BUG: index 42
WARNING: CPU: 2 PID: 4054 at net/sched/act_pedit.c:410 tcf_pedit_act+0xc84/0x1200 [act_pedit]
[...]
RIP: 0010:tcf_pedit_act+0xc84/0x1200 [act_pedit]
Code: 89 fa 48 c1 ea 03 0f b6 04 02 84 c0 74 08 3c 03 0f 8e ac 00 00 00 48 8b 44 24 10 48 c7 c7 a0 c4 e4 c0 8b 70 18 e8 1c 30 95 ea <0f> 0b e9 a0 fa ff ff e8 00 03 f5 ea e9 14 f4 ff ff 48 89 58 40 e9
RSP: 0018:ffff888077c9f320 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffac2983a2
RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff888053927bec
RBP: dffffc0000000000 R08: ffffed100a726209 R09: ffffed100a726209
R10: 0000000000000001 R11: ffffed100a726208 R12: ffff88804beea780
R13: ffff888079a77400 R14: ffff88804beea780 R15: ffff888027ab2000
FS: 00007fdeec9bd740(0000) GS:ffff888053900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffdb3dfd000 CR3: 000000004adb4006 CR4: 00000000001606e0
Call Trace:
tcf_action_exec+0x105/0x3f0
tcf_classify+0xf2/0x410
__dev_queue_xmit+0xcbf/0x2ae0
ip_finish_output2+0x711/0x1fb0
ip_output+0x1bf/0x4b0
ip_send_skb+0x37/0xa0
raw_sendmsg+0x180c/0x2430
sock_sendmsg+0xdb/0x110
__sys_sendto+0x257/0x2b0
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0xa5/0x4e0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fdeeb72e993
Code: 48 8b 0d e0 74 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 0d d6 2c 00 00 75 13 49 89 ca b8 2c 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 4b cc 00 00 48 89 04 24
RSP: 002b:00007ffdb3de8a18 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 000055c81972b700 RCX: 00007fdeeb72e993
RDX: 0000000000000040 RSI: 000055c81972b700 RDI: 0000000000000003
RBP: 00007ffdb3dea130 R08: 000055c819728510 R09: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
R13: 000055c81972b6c0 R14: 000055c81972969c R15: 0000000000000080
Fix this moving the check on 'nkeys' earlier in tcf_pedit_init(), so that
attempts to install rules having 0 keys are always rejected with -EINVAL.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.
This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.
Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
