| Age | Commit message (Collapse) | Author |
|---|
|
of_get_named_gpiod_flags fails with -EPROBE_DEFER in cases
where the gpio chip is available and the GPIO translation fails.
This causes drivers to be re-probed erroneusly, and hides the
real problem(i.e. the GPIO number being out of range).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix attribute-creation race with userspace by using the default group
to create also the contingent gpio device attributes.
Fixes: d8f388d8dc8d ("gpio: sysfs interface")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio device attributes were never destroyed when the gpio was
unexported (or on export failures).
Use device_create_with_groups() to create the default device attributes
of the gpio class device. Note that this also fixes the
attribute-creation race with userspace for these attributes.
Remove contingent attributes in export error path and on unexport.
Fixes: d8f388d8dc8d ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio-chip device attributes were never destroyed when the device was
removed.
Fix by using device_create_with_groups() to create the device attributes
of the chip class device.
Note that this also fixes the attribute-creation race with userspace.
Fixes: d8f388d8dc8d ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This was accidently lost in 76a0df859def.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We should not touch the packet after a netif_rx: it might
get freed behind our back.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Finally there will be three types of CAN FD controllers in the future:
1. ISO compliant (fixed)
2. non-ISO compliant (fixed, like the M_CAN IP v3.0.1 in m_can.c)
3. ISO/non-ISO CAN FD controllers (switchable, like the PEAK USB FD)
So the current M_CAN driver for the M_CAN IP v3.0.1 has to expose its non-ISO
implementation by setting the CAN_CTRLMODE_FD_NON_ISO ctrlmode at startup.
As this bit cannot be switched at configuration time CAN_CTRLMODE_FD_NON_ISO
must not be set in ctrlmode_supported of the current M_CAN driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The linux-can upstream git repositories are now hosted on kernel.org, update
MAINTAINERS accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
If the first queue created was failed on DQM then PQM should
unregister the process from DQM.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
|
|
Commit 90cee759f08a ("MIPS: ELF: Set FP mode according to .MIPS.abiflags")
introduced checking of the .MIPS.abiflags ELF section but did so through
the native sized "elfhdr" and "elf_phdr" structures regardless whether the
ELF was actually 32-bit or 64-bit. This produces wrong results when trying
to use a 64-bit kernel to load o32 ELF files.
Change the uses of the generic elf structures to their 32-bit versions.
Since the code bails out on any 64-bit cases, this is OK until they are
implemented.
Fixes: 90cee759f08a ("MIPS: ELF: Set FP mode according to .MIPS.abiflags")
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8932/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 5f893b2639b2 "tracing: Move enabling tracepoints to just after
rcu_init()" broke the enabling of system call events from the command
line. The reason was that the enabling of command line trace events
was moved before PID 1 started, and the syscall tracepoints require
that all tasks have the TIF_SYSCALL_TRACEPOINT flag set. But the
swapper task (pid 0) is not part of that. Since the swapper task is the
only task that is running at this early in boot, no task gets the
flag set, and the tracepoint never gets reached.
Instead of setting the swapper task flag (there should be no reason to
do that), re-enabled trace events again after the init thread (PID 1)
has been started. It requires disabling all command line events and
re-enabling them, as just enabling them again will not reset the logic
to set the TIF_SYSCALL_TRACEPOINT flag, as the syscall tracepoint will
be fooled into thinking that it was already set, and wont try setting
it again. For this reason, we must first disable it and re-enable it.
Link: http://lkml.kernel.org/r/1421188517-18312-1-git-send-email-mpe@ellerman.id.au
Link: http://lkml.kernel.org/r/20150115040506.216066449@goodmis.org
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
trace_init() calls init_ftrace_syscalls() and then calls trace_event_init()
which also calls init_ftrace_syscalls(). It makes more sense to only
call it from trace_event_init().
Calling it twice wastes memory, as it allocates the syscall events twice,
and loses the first copy of it.
Link: http://lkml.kernel.org/r/54AF53BD.5070303@huawei.com
Link: http://lkml.kernel.org/r/20150115040505.930398632@goodmis.org
Reported-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
If the function graph tracer traces a jprobe callback, the system will
crash. This can easily be demonstrated by compiling the jprobe
sample module that is in the kernel tree, loading it and running the
function graph tracer.
# modprobe jprobe_example.ko
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
# ls
The first two commands end up in a nice crash after the first fork.
(do_fork has a jprobe attached to it, so "ls" just triggers that fork)
The problem is caused by the jprobe_return() that all jprobe callbacks
must end with. The way jprobes works is that the function a jprobe
is attached to has a breakpoint placed at the start of it (or it uses
ftrace if fentry is supported). The breakpoint handler (or ftrace callback)
will copy the stack frame and change the ip address to return to the
jprobe handler instead of the function. The jprobe handler must end
with jprobe_return() which swaps the stack and does an int3 (breakpoint).
This breakpoint handler will then put back the saved stack frame,
simulate the instruction at the beginning of the function it added
a breakpoint to, and then continue on.
For function tracing to work, it hijakes the return address from the
stack frame, and replaces it with a hook function that will trace
the end of the call. This hook function will restore the return
address of the function call.
If the function tracer traces the jprobe handler, the hook function
for that handler will not be called, and its saved return address
will be used for the next function. This will result in a kernel crash.
To solve this, pause function tracing before the jprobe handler is called
and unpause it before it returns back to the function it probed.
Some other updates:
Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the
code look a bit cleaner and easier to understand (various tries to fix
this bug required this change).
Note, if fentry is being used, jprobes will change the ip address before
the function graph tracer runs and it will not be able to trace the
function that the jprobe is probing.
Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.org
Cc: stable@vger.kernel.org # 2.6.30+
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Using just the filter for checking for trampolines or regs is not enough
when updating the code against the records that represent all functions.
Both the filter hash and the notrace hash need to be checked.
To trigger this bug (using trace-cmd and perf):
# perf probe -a do_fork
# trace-cmd start -B foo -e probe
# trace-cmd record -p function_graph -n do_fork sleep 1
The trace-cmd record at the end clears the filter before it disables
function_graph tracing and then that causes the accounting of the
ftrace function records to become incorrect and causes ftrace to bug.
Link: http://lkml.kernel.org/r/20150114154329.358378039@goodmis.org
Cc: stable@vger.kernel.org
[ still need to switch old_hash_ops to old_ops_hash ]
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
As the set_ftrace_filter affects both the function tracer as well as the
function graph tracer, the ops that represent each have a shared
ftrace_ops_hash structure. This allows both to be updated when the filter
files are updated.
But if function graph is enabled and the global_ops (function tracing) ops
is not, then it is possible that the filter could be changed without the
update happening for the function graph ops. This will cause the changes
to not take place and may even cause a ftrace_bug to occur as it could mess
with the trampoline accounting.
The solution is to check if the ops uses the shared global_ops filter and
if the ops itself is not enabled, to check if there's another ops that is
enabled and also shares the global_ops filter. In that case, the
modification still needs to be executed.
Link: http://lkml.kernel.org/r/20150114154329.055980438@goodmis.org
Cc: stable@vger.kernel.org # 3.17+
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
|
|
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
into x86/cleanups
Pull minor x86 cleanups from Borislav Petkov.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull RAS update from Tony Luck:
"When checking addresses in APEI action entries for validity, allow
access to the mmcfg space - some error injection functions need to do
this."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
"Nothing special this time, just an error messages improvement from Andy
and a cleanup from me."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Refine code by normailizing the way to detect whether IR is enabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Change variable disable_irq_remap to be static and simplify the code.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Assign intel_irq_remap_ops to remap_ops only if
intel_irq_remap_ops.prepare() succeeds.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-15-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Simplify irq_remapping code by killing irq_remapping_supported() and
related interfaces.
Joerg posted a similar patch at https://lkml.org/lkml/2014/12/15/490,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This allows to get rid of the irq_remapping_supported() function and
all its call-backs into the Intel and AMD IOMMU drivers.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When interrupt remapping hardware is not in X2APIC, CPU X2APIC mode
will be disabled if:
1) Maximum CPU APIC ID is bigger than 255
2) hypervisior doesn't support x2apic mode.
But we should only check whether hypervisor supports X2APIC mode when
hypervisor(CONFIG_HYPERVISOR_GUEST) is enabled, otherwise X2APIC will
always be disabled when CONFIG_HYPERVISOR_GUEST is disabled and IR
doesn't work in X2APIC mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-12-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Currently if CPU supports X2APIC, IR hardware must work in X2APIC mode
or disabled. Change the code to support IR working in XAPIC mode when
CPU supports X2APIC. Then the CPU APIC driver will decide how to handle
such as configuration by:
1) Disabling X2APIC mode
2) Forcing X2APIC physical mode
This change also fixes a live locking when
1) BIOS enables CPU X2APIC
2) DMAR table disables X2APIC mode or IR hardware doesn't support X2APIC
with following messages:
[ 37.863463] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.863463] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.879372] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.879372] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.895282] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
[ 37.895282] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry
[ 37.911192] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-11-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
IRQ remapping is only supported when all IOMMUs in the
system support it. So check if all IOMMUs in the system
support IRQ remapping before doing the allocations.
[Jiang]
1) Rebased to v3.19.
2) Remove redundant check of ecap_ir_support(iommu->ecap) in function
intel_enable_irq_remapping().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Prepare for killing function irq_remapping_supported() by moving code
from intel_irq_remapping_supported() into intel_prepare_irq_remapping().
Combined with patch from Joerg at https://lkml.org/lkml/2014/12/15/487,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1420615903-28253-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If remapping is in XAPIC mode, the setup code just skips X2APIC
initialization without checking max CPU APIC ID in system, which may
cause problem if system has a CPU with APIC ID bigger than 255.
Handle IR in XAPIC mode the same way as if remapping is disabled.
[ tglx: Split out from previous patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Refine enable_IR_x2apic() and related functions for better readability.
[ tglx: Removed the XAPIC mode change and split it out into a seperate
patch. Added comments. ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
X2APIC will be disabled if user specifies "nox2apic" on kernel command
line, even when x2apic_preenabled is true. So correctly detect X2APIC
status by using x2apic_enabled() instead of x2apic_preenabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Local variable x2apic_enabled has been assigned to but never referred,
so kill it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When kernel doesn't support X2APIC but BIOS has enabled X2APIC, system
may panic or hang without useful messages. On the other hand, it's
hard to dynamically disable X2APIC when CONFIG_X86_X2APIC is disabled.
So panic with a clear message in such a case.
Now system panics as below when X2APIC is disabled and interrupt remapping
is enabled:
[ 0.316118] LAPIC pending interrupts after 512 EOI
[ 0.322126] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.368655] Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
[ 0.378300] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0+ #340
[ 0.385300] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIN1.86B.0051.L05.1406240953 06/24/2014
[ 0.396997] ffff88046dc03000 ffff88046c307dd8 ffffffff8179dada 00000000000043f2
[ 0.405629] ffffffff81a92158 ffff88046c307e58 ffffffff8179b757 0000000000000002
[ 0.414261] 0000000000000008 ffff88046c307e68 ffff88046c307e08 ffffffff813ad82b
[ 0.422890] Call Trace:
[ 0.425711] [<ffffffff8179dada>] dump_stack+0x45/0x57
[ 0.431533] [<ffffffff8179b757>] panic+0xc1/0x1f5
[ 0.436978] [<ffffffff813ad82b>] ? delay_tsc+0x3b/0x70
[ 0.442910] [<ffffffff8166fa2c>] panic_if_irq_remap+0x1c/0x20
[ 0.449524] [<ffffffff81d73645>] setup_IO_APIC+0x405/0x82e
[ 0.464979] [<ffffffff81d6fcc2>] native_smp_prepare_cpus+0x2d9/0x31c
[ 0.472274] [<ffffffff81d5d0ac>] kernel_init_freeable+0xd6/0x223
[ 0.479170] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.485099] [<ffffffff81792ade>] kernel_init+0xe/0xf0
[ 0.490932] [<ffffffff817a537c>] ret_from_fork+0x7c/0xb0
[ 0.497054] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.502983] ---[ end Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
System hangs as below when X2APIC and interrupt remapping are both disabled:
[ 1.102782] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 1.109351] pci 0000:00:03.0: System wakeup disabled by ACPI
[ 1.115915] pci 0000:00:03.2: System wakeup disabled by ACPI
[ 1.122479] pci 0000:00:03.3: System wakeup disabled by ACPI
[ 1.132274] pci 0000:00:1c.0: Enabling MPC IRBNCE
[ 1.137620] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled
[ 1.145239] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.151790] pci 0000:00:1c.7: Enabling MPC IRBNCE
[ 1.157128] pci 0000:00:1c.7: Intel PCH root port ACS workaround enabled
[ 1.164748] pci 0000:00:1c.7: System wakeup disabled by ACPI
[ 1.171447] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 1.178612] acpiphp: Slot [8] registered
[ 1.183095] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.188867] acpiphp: Slot [2] registered
With this patch applied, the system panics in both cases with a proper
panic message.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If x2apic got disabled on the kernel command line, then the following
issue can happen:
enable_IR_x2apic()
....
x2apic_mode = 1;
enable_x2apic();
if (x2apic_disabled) {
__disable_x2apic();
return;
}
That leaves X2APIC disabled in hardware, but x2apic_mode stays 1. So
all other code which checks x2apic_mode gets the wrong information.
Set x2apic_mode to 0 after disabling it in hardware.
This is just a hotfix. The proper solution is to rework this code so
it has seperate functions for the initial setup on the boot processor
and the secondary cpus, but that's beyond the scope of this fix.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
|
|
No reason anymore to do GFP_ATOMIC allocations which are not harmful
in the normal bootup case, but matter in the physical hotplug
scenario.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.472428339@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The whole iommu setup for irq remapping is a convoluted mess. The
iommu detect function gets called from mem_init() and the prepare
callback gets called from enable_IR_x2apic() for unknown reasons.
Of course AMD and Intel setup differs in nonsensical ways. Intels
prepare callback is explicit while AMDs prepare callback is implicit
in setup_irq_remapping_ops() just to be called in the prepare call
again.
Because all of this gets called from enable_IR_x2apic() and the dmar
prepare function merily parses the ACPI tables, but does not allocate
memory we end up with memory allocation from irq disabled context
later on.
AMDs iommu code at least allocates the required memory from the
prepare function. That has issues as well, but thats not scope of this
patch.
The goal of this change is to distangle the allocation from the actual
enablement. There is no point to allocate memory from irq disabled
regions with GFP_ATOMIC just because it does not matter at that point
in the boot stage. It matters with physical hotplug later on.
There is another issue with the current setup. Due to the conversion
to stacked irqdomains we end up with a call into the irqdomain
allocation code from irq disabled context, but that code does
GFP_KERNEL allocations rightfully as there is no reason to do
preperatory allocations with GFP_ATOMIC.
That change caused the allocator code to complain about GFP_KERNEL
allocations invoked in atomic context. Boris provided a temporary
hackaround which changed the GFP flags if irq_domain_add() got called
from atomic context. Not pretty and we really dont want to get this
into a mainline release for obvious reasons.
Move the ACPI table parsing and the resulting memory allocations from
the enable to the prepare function. That allows to get rid of the
horrible hackaround in irq_domain_add() later.
[Jiang] Rebased onto v3.19
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.313026156@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
enable_IR_x2apic() calls setup_irq_remapping_ops() which by default
installs the intel dmar remapping ops and then calls the amd iommu irq
remapping prepare callback to figure out whether we are running on an
AMD machine with irq remapping hardware.
Right after that it calls irq_remapping_prepare() which pointlessly
checks:
if (!remap_ops || !remap_ops->prepare)
return -ENODEV;
and then calls
remap_ops->prepare()
which is silly in the AMD case as it got called from
setup_irq_remapping_ops() already a few microseconds ago.
Simplify this and just collapse everything into
irq_remapping_prepare().
The irq_remapping_prepare() remains still silly as it assigns blindly
the intel ops, but that's not scope of this patch.
The scope here is to move the preperatory work, i.e. memory
allocations out of the atomic section which is required to enable irq
remapping.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.232633738@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The s390x ABI requires to zero extend parameters before functions
are called.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
In sk_load_byte_msh() sk_load_byte_slow() is called instead of
sk_load_byte_msh_slow(). Fix this and call the correct function.
Besides of this load only one byte instead of two and fix the comment.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the offset parameter for skb_copy_bits is changed in
sk_load_word() and sk_load_half(). Therefore it is not correct when
calling skb_copy_bits(). Fix this and use the original offset
for the function call.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The skb_copy_bits() function has the following signature:
int skb_copy_bits(const struct sk_buff *skb, int offset, void *to, int len)
Currently in bpf_jit.S the "to" and "len" parameters have been
exchanged. So fix this and call the function with the correct
parameters.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the signed COMPARE HALFWORD IMMEDIATE (chi) and COMPARE (c)
instructions are used to compare "A" with "K". This is not correct
because "A" and "K" are both unsigned. To fix this remove the
chi instruction (no unsigned analogon available) and use the
unsigned COMPARE LOGICAL (cl) instruction instead of COMPARE (c).
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
