| Age | Commit message (Collapse) | Author |
|---|
|
When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.
Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Tested-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reverts commit fb47ada8dc3c30c8e7b415da155742b49536c61e.
In some situations when we set TXOP_BACKOFF, the probe frame is
not sent at all. What it worse then sending probe frame as part
of AMPDU and can degrade 11n performance to 11g rates.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
working-branch-for-4.18
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
Without CONFIG_INPUT, or with a modular input layer and built-in
tablet driver, we get a link error:
ERROR: "input_event" [drivers/platform/chrome/chromeos_tbmc.ko] undefined!
ERROR: "input_register_device" [drivers/platform/chrome/chromeos_tbmc.ko] undefined!
ERROR: "input_set_capability" [drivers/platform/chrome/chromeos_tbmc.ko] undefined!
ERROR: "devm_input_allocate_device" [drivers/platform/chrome/chromeos_tbmc.ko] undefined!
This adds the corresponding Kconfig dependency
Fixes: b418f74170d7 ("platform: chrome: Add Tablet Switch ACPI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
The netsec network controller IP can drive 64 address bits for DMA, and
the DMA mask is set accordingly in the driver. However, the SynQuacer
SoC, which is the only silicon incorporating this IP at the moment,
integrates this IP in a manner that leaves address bits [63:40]
unconnected.
Up until now, this has not resulted in any problems, given that the DDR
controller doesn't decode those bits to begin with. However, recent
firmware updates for platforms incorporating this SoC allow the IOMMU
to be enabled, which does decode address bits [47:40], and allocates
top down from the IOVA space, producing DMA addresses that have bits
set that have been left unconnected.
Both the DT and ACPI (IORT) descriptions of the platform take this into
account, and only describe a DMA address space of 40 bits (using either
dma-ranges DT properties, or DMA address limits in IORT named component
nodes). However, even though our IOMMU and bus layers may take such
limitations into account by setting a narrower DMA mask when creating
the platform device, the netsec probe() entrypoint follows the common
practice of setting the DMA mask uncondionally, according to the
capabilities of the IP block itself rather than to its integration into
the chip.
It is currently unclear what the correct fix is here. We could hack around
it by only setting the DMA mask if it deviates from its default value of
DMA_BIT_MASK(32). However, this makes it impossible for the bus layer to
use DMA_BIT_MASK(32) as the bus limit, and so it appears that a more
comprehensive approach is required to take DMA limits imposed by the
SoC as a whole into account.
In the mean time, let's limit the DMA mask to 40 bits. Given that there
is currently only one SoC that incorporates this IP, this is a reasonable
approach that can be backported to -stable and buys us some time to come
up with a proper fix going forward.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seg6_do_srh_encap and seg6_do_srh_inline can possibly do an
out-of-bounds access when adding the SRH to the packet. This no longer
happen when expanding the skb not only by the size of the SRH (+
outer IPv6 header), but also by skb->mac_len.
[ 53.793056] BUG: KASAN: use-after-free in seg6_do_srh_encap+0x284/0x620
[ 53.794564] Write of size 14 at addr ffff88011975ecfa by task ping/674
[ 53.796665] CPU: 0 PID: 674 Comm: ping Not tainted 4.17.0-rc3-ARCH+ #90
[ 53.796670] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.11.0-20171110_100015-anatol 04/01/2014
[ 53.796673] Call Trace:
[ 53.796679] <IRQ>
[ 53.796689] dump_stack+0x71/0xab
[ 53.796700] print_address_description+0x6a/0x270
[ 53.796707] kasan_report+0x258/0x380
[ 53.796715] ? seg6_do_srh_encap+0x284/0x620
[ 53.796722] memmove+0x34/0x50
[ 53.796730] seg6_do_srh_encap+0x284/0x620
[ 53.796741] ? seg6_do_srh+0x29b/0x360
[ 53.796747] seg6_do_srh+0x29b/0x360
[ 53.796756] seg6_input+0x2e/0x2e0
[ 53.796765] lwtunnel_input+0x93/0xd0
[ 53.796774] ipv6_rcv+0x690/0x920
[ 53.796783] ? ip6_input+0x170/0x170
[ 53.796791] ? eth_gro_receive+0x2d0/0x2d0
[ 53.796800] ? ip6_input+0x170/0x170
[ 53.796809] __netif_receive_skb_core+0xcc0/0x13f0
[ 53.796820] ? netdev_info+0x110/0x110
[ 53.796827] ? napi_complete_done+0xb6/0x170
[ 53.796834] ? e1000_clean+0x6da/0xf70
[ 53.796845] ? process_backlog+0x129/0x2a0
[ 53.796853] process_backlog+0x129/0x2a0
[ 53.796862] net_rx_action+0x211/0x5c0
[ 53.796870] ? napi_complete_done+0x170/0x170
[ 53.796887] ? run_rebalance_domains+0x11f/0x150
[ 53.796891] __do_softirq+0x10e/0x39e
[ 53.796894] do_softirq_own_stack+0x2a/0x40
[ 53.796895] </IRQ>
[ 53.796898] do_softirq.part.16+0x54/0x60
[ 53.796900] __local_bh_enable_ip+0x5b/0x60
[ 53.796903] ip6_finish_output2+0x416/0x9f0
[ 53.796906] ? ip6_dst_lookup_flow+0x110/0x110
[ 53.796909] ? ip6_sk_dst_lookup_flow+0x390/0x390
[ 53.796911] ? __rcu_read_unlock+0x66/0x80
[ 53.796913] ? ip6_mtu+0x44/0xf0
[ 53.796916] ? ip6_output+0xfc/0x220
[ 53.796918] ip6_output+0xfc/0x220
[ 53.796921] ? ip6_finish_output+0x2b0/0x2b0
[ 53.796923] ? memcpy+0x34/0x50
[ 53.796926] ip6_send_skb+0x43/0xc0
[ 53.796929] rawv6_sendmsg+0x1216/0x1530
[ 53.796932] ? __orc_find+0x6b/0xc0
[ 53.796934] ? rawv6_rcv_skb+0x160/0x160
[ 53.796937] ? __rcu_read_unlock+0x66/0x80
[ 53.796939] ? __rcu_read_unlock+0x66/0x80
[ 53.796942] ? is_bpf_text_address+0x1e/0x30
[ 53.796944] ? kernel_text_address+0xec/0x100
[ 53.796946] ? __kernel_text_address+0xe/0x30
[ 53.796948] ? unwind_get_return_address+0x2f/0x50
[ 53.796950] ? __save_stack_trace+0x92/0x100
[ 53.796954] ? save_stack+0x89/0xb0
[ 53.796956] ? kasan_kmalloc+0xa0/0xd0
[ 53.796958] ? kmem_cache_alloc+0xd2/0x1f0
[ 53.796961] ? prepare_creds+0x23/0x160
[ 53.796963] ? __x64_sys_capset+0x252/0x3e0
[ 53.796966] ? do_syscall_64+0x69/0x160
[ 53.796968] ? entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.796971] ? __alloc_pages_nodemask+0x170/0x380
[ 53.796973] ? __alloc_pages_slowpath+0x12c0/0x12c0
[ 53.796977] ? tty_vhangup+0x20/0x20
[ 53.796979] ? policy_nodemask+0x1a/0x90
[ 53.796982] ? __mod_node_page_state+0x8d/0xa0
[ 53.796986] ? __check_object_size+0xe7/0x240
[ 53.796989] ? __sys_sendto+0x229/0x290
[ 53.796991] ? rawv6_rcv_skb+0x160/0x160
[ 53.796993] __sys_sendto+0x229/0x290
[ 53.796996] ? __ia32_sys_getpeername+0x50/0x50
[ 53.796999] ? commit_creds+0x2de/0x520
[ 53.797002] ? security_capset+0x57/0x70
[ 53.797004] ? __x64_sys_capset+0x29f/0x3e0
[ 53.797007] ? __x64_sys_rt_sigsuspend+0xe0/0xe0
[ 53.797011] ? __do_page_fault+0x664/0x770
[ 53.797014] __x64_sys_sendto+0x74/0x90
[ 53.797017] do_syscall_64+0x69/0x160
[ 53.797019] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797022] RIP: 0033:0x7f43b7a6714a
[ 53.797023] RSP: 002b:00007ffd891bd368 EFLAGS: 00000246 ORIG_RAX:
000000000000002c
[ 53.797026] RAX: ffffffffffffffda RBX: 00000000006129c0 RCX: 00007f43b7a6714a
[ 53.797028] RDX: 0000000000000040 RSI: 00000000006129c0 RDI: 0000000000000004
[ 53.797029] RBP: 00007ffd891be640 R08: 0000000000610940 R09: 000000000000001c
[ 53.797030] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[ 53.797032] R13: 000000000060e6a0 R14: 0000000000008004 R15: 000000000040b661
[ 53.797171] Allocated by task 642:
[ 53.797460] kasan_kmalloc+0xa0/0xd0
[ 53.797463] kmem_cache_alloc+0xd2/0x1f0
[ 53.797465] getname_flags+0x40/0x210
[ 53.797467] user_path_at_empty+0x1d/0x40
[ 53.797469] do_faccessat+0x12a/0x320
[ 53.797471] do_syscall_64+0x69/0x160
[ 53.797473] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797607] Freed by task 642:
[ 53.797869] __kasan_slab_free+0x130/0x180
[ 53.797871] kmem_cache_free+0xa8/0x230
[ 53.797872] filename_lookup+0x15b/0x230
[ 53.797874] do_faccessat+0x12a/0x320
[ 53.797876] do_syscall_64+0x69/0x160
[ 53.797878] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.798014] The buggy address belongs to the object at ffff88011975e600
which belongs to the cache names_cache of size 4096
[ 53.799043] The buggy address is located 1786 bytes inside of
4096-byte region [ffff88011975e600, ffff88011975f600)
[ 53.800013] The buggy address belongs to the page:
[ 53.800414] page:ffffea000465d600 count:1 mapcount:0
mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 53.801259] flags: 0x17fff0000008100(slab|head)
[ 53.801640] raw: 017fff0000008100 0000000000000000 0000000000000000
0000000100070007
[ 53.803147] raw: dead000000000100 dead000000000200 ffff88011b185a40
0000000000000000
[ 53.803787] page dumped because: kasan: bad access detected
[ 53.804384] Memory state around the buggy address:
[ 53.804788] ffff88011975eb80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805384] ffff88011975ec00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805979] >ffff88011975ec80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.806577] ^
[ 53.807165] ffff88011975ed00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.807762] ffff88011975ed80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.808356] ==================================================================
[ 53.808949] Disabling lock debugging due to kernel taint
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Null pointer dereference when dumping conntrack helper configuration,
from Taehee Yoo.
2) Missing sanitization in ebtables extension name through compat,
from Paolo Abeni.
3) Broken fetch of tracing value, from Taehee Yoo.
4) Incorrect arithmetics in packet ratelimiting.
5) Buffer overflow in IPVS sync daemon, from Julian Anastasov.
6) Wrong argument to nla_strlcpy() in nfnetlink_{acct,cthelper},
from Eric Dumazet.
7) Fix splat in nft_update_chain_stats().
8) Null pointer dereference from object netlink dump path, from
Taehee Yoo.
9) Missing static_branch_inc() when enabling counters in existing
chain, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:
BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19
CPU: 1 PID: 19 Comm: kworker/1:0H Not tainted 4.16.0-rc3-dbg+ #1
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
srp_timed_out+0x57/0x110 [scsi_transport_srp]
scsi_times_out+0xc7/0x3f0 [scsi_mod]
blk_mq_terminate_expired+0xc2/0x140
bt_iter+0xbc/0xd0
blk_mq_queue_tag_busy_iter+0x1c7/0x350
blk_mq_timeout_work+0x325/0x3f0
process_one_work+0x441/0xa50
worker_thread+0x76/0x6c0
kthread+0x1b2/0x1d0
ret_from_fork+0x24/0x30
Fixes: e68ca75200fe ("scsi_transport_srp: Reduce failover time")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a chain is updated, a counter can be attached. if so,
the nft_counters_enabled should be increased.
test commands:
%nft add table ip filter
%nft add chain ip filter input { type filter hook input priority 4\; }
%iptables-compat -Z input
%nft delete chain ip filter input
we can see below messages.
[ 286.443720] jump label: negative count!
[ 286.448278] WARNING: CPU: 0 PID: 1459 at kernel/jump_label.c:197 __static_key_slow_dec_cpuslocked+0x6f/0xf0
[ 286.449144] Modules linked in: nf_tables nfnetlink ip_tables x_tables
[ 286.449144] CPU: 0 PID: 1459 Comm: nft Tainted: G W 4.17.0-rc2+ #12
[ 286.449144] RIP: 0010:__static_key_slow_dec_cpuslocked+0x6f/0xf0
[ 286.449144] RSP: 0018:ffff88010e5176f0 EFLAGS: 00010286
[ 286.449144] RAX: 000000000000001b RBX: ffffffffc0179500 RCX: ffffffffb8a82522
[ 286.449144] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88011b7e5eac
[ 286.449144] RBP: 0000000000000000 R08: ffffed00236fce5c R09: ffffed00236fce5b
[ 286.449144] R10: ffffffffc0179503 R11: ffffed00236fce5c R12: 0000000000000000
[ 286.449144] R13: ffff88011a28e448 R14: ffff88011a28e470 R15: dffffc0000000000
[ 286.449144] FS: 00007f0384328700(0000) GS:ffff88011b600000(0000) knlGS:0000000000000000
[ 286.449144] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 286.449144] CR2: 00007f038394bf10 CR3: 0000000104a86000 CR4: 00000000001006f0
[ 286.449144] Call Trace:
[ 286.449144] static_key_slow_dec+0x6a/0x70
[ 286.449144] nf_tables_chain_destroy+0x19d/0x210 [nf_tables]
[ 286.449144] nf_tables_commit+0x1891/0x1c50 [nf_tables]
[ 286.449144] nfnetlink_rcv+0x1148/0x13d0 [nfnetlink]
[ ... ]
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The table field in nft_obj_filter is not an array. In order to check
tablename, we should check if the pointer is set.
Test commands:
%nft add table ip filter
%nft add counter ip filter ct1
%nft reset counters
Splat looks like:
[ 306.510504] kasan: CONFIG_KASAN_INLINE enabled
[ 306.516184] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 306.524775] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 306.528284] Modules linked in: nft_objref nft_counter nf_tables nfnetlink ip_tables x_tables
[ 306.528284] CPU: 0 PID: 1488 Comm: nft Not tainted 4.17.0-rc4+ #17
[ 306.528284] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[ 306.528284] RIP: 0010:nf_tables_dump_obj+0x52c/0xa70 [nf_tables]
[ 306.528284] RSP: 0018:ffff8800b6cb7520 EFLAGS: 00010246
[ 306.528284] RAX: 0000000000000000 RBX: ffff8800b6c49820 RCX: 0000000000000000
[ 306.528284] RDX: 0000000000000000 RSI: dffffc0000000000 RDI: ffffed0016d96e9a
[ 306.528284] RBP: ffff8800b6cb75c0 R08: ffffed00236fce7c R09: ffffed00236fce7b
[ 306.528284] R10: ffffffff9f6241e8 R11: ffffed00236fce7c R12: ffff880111365108
[ 306.528284] R13: 0000000000000000 R14: ffff8800b6c49860 R15: ffff8800b6c49860
[ 306.528284] FS: 00007f838b007700(0000) GS:ffff88011b600000(0000) knlGS:0000000000000000
[ 306.528284] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 306.528284] CR2: 00007ffeafabcf78 CR3: 00000000b6cbe000 CR4: 00000000001006f0
[ 306.528284] Call Trace:
[ 306.528284] netlink_dump+0x470/0xa20
[ 306.528284] __netlink_dump_start+0x5ae/0x690
[ 306.528284] ? nf_tables_getobj+0x1b3/0x740 [nf_tables]
[ 306.528284] nf_tables_getobj+0x2f5/0x740 [nf_tables]
[ 306.528284] ? nft_obj_notify+0x100/0x100 [nf_tables]
[ 306.528284] ? nf_tables_getobj+0x740/0x740 [nf_tables]
[ 306.528284] ? nf_tables_dump_flowtable_done+0x70/0x70 [nf_tables]
[ 306.528284] ? nft_obj_notify+0x100/0x100 [nf_tables]
[ 306.528284] nfnetlink_rcv_msg+0x8ff/0x932 [nfnetlink]
[ 306.528284] ? nfnetlink_rcv_msg+0x216/0x932 [nfnetlink]
[ 306.528284] netlink_rcv_skb+0x1c9/0x2f0
[ 306.528284] ? nfnetlink_bind+0x1d0/0x1d0 [nfnetlink]
[ 306.528284] ? debug_check_no_locks_freed+0x270/0x270
[ 306.528284] ? netlink_ack+0x7a0/0x7a0
[ 306.528284] ? ns_capable_common+0x6e/0x110
[ ... ]
Fixes: e46abbcc05aa8 ("netfilter: nf_tables: Allow table names of up to 255 chars")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch fixes the following splat.
[118709.054937] BUG: using smp_processor_id() in preemptible [00000000] code: test/1571
[118709.054970] caller is nft_update_chain_stats.isra.4+0x53/0x97 [nf_tables]
[118709.054980] CPU: 2 PID: 1571 Comm: test Not tainted 4.17.0-rc6+ #335
[...]
[118709.054992] Call Trace:
[118709.055011] dump_stack+0x5f/0x86
[118709.055026] check_preemption_disabled+0xd4/0xe4
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The extra forward declaration of pm_qos_get_value() is redundant, so
drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Kernel library has a common function to match user input from sysfs
against an array of strings. Thus, replace bch_read_string_list() by
__sysfs_match_string().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is couple of functions that are used exclusively in sysfs.c.
Move it to there and make them static.
Besides above, it will allow further clean up.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is couple of string arrays that are used exclusively in sysfs.c.
Move it to there and make them static.
Besides above, it will allow further clean up.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently bcache does not handle backing device failure, if backing
device is offline and disconnected from system, its bcache device can still
be accessible. If the bcache device is in writeback mode, I/O requests even
can success if the requests hit on cache device. That is to say, when and
how bcache handles offline backing device is undefined.
This patch tries to handle backing device offline in a rather simple way,
- Add cached_dev->status_update_thread kernel thread to update backing
device status in every 1 second.
- Add cached_dev->offline_seconds to record how many seconds the backing
device is observed to be offline. If the backing device is offline for
BACKING_DEV_OFFLINE_TIMEOUT (30) seconds, set dc->io_disable to 1 and
call bcache_device_stop() to stop the bache device which linked to the
offline backing device.
Now if a backing device is offline for BACKING_DEV_OFFLINE_TIMEOUT seconds,
its bcache device will be removed, then user space application writing on
it will get error immediately, and handler the device failure in time.
This patch is quite simple, does not handle more complicated situations.
Once the bcache device is stopped, users need to recovery the backing
device, register and attach it manually.
Changelog:
v3: call wait_for_kthread_stop() before exits kernel thread.
v2: remove "bcache: " prefix when calling pr_warn().
v1: initial version.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Michael Lyle <mlyle@lyle.org>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Looks like this got lost in a merge.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The snapshot trigger currently only affects the main ring buffer, even when
it is used by the instances. This can be confusing as the snapshot trigger
is listed in the instance.
> # cd /sys/kernel/tracing
> # mkdir instances/foo
> # echo snapshot > instances/foo/events/syscalls/sys_enter_fchownat/trigger
> # echo top buffer > trace_marker
> # echo foo buffer > instances/foo/trace_marker
> # touch /tmp/bar
> # chown rostedt /tmp/bar
> # cat instances/foo/snapshot
# tracer: nop
#
#
# * Snapshot is freed *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
> # cat snapshot
# tracer: nop
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
bash-1189 [000] .... 111.488323: tracing_mark_write: top buffer
Not only did the snapshot occur in the top level buffer, but the instance
snapshot buffer should have been allocated, and it is still free.
Cc: stable@vger.kernel.org
Fixes: 85f2b08268c01 ("tracing: Add basic event trigger framework")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Several subsystems depend on INFINIBAND_ADDR_TRANS, which in turn depends
on INFINIBAND. However, when with CONFIG_INIFIBAND=m, this leads to a
link error when another driver using it is built-in. The
INFINIBAND_ADDR_TRANS dependency is insufficient here as this is
a 'bool' symbol that does not force anything to be a module in turn.
fs/cifs/smbdirect.o: In function `smbd_disconnect_rdma_work':
smbdirect.c:(.text+0x1e4): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_request':
trans_rdma.c:(.text+0x7bc): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_destroy_trans':
trans_rdma.c:(.text+0x830): undefined reference to `ib_destroy_qp'
trans_rdma.c:(.text+0x858): undefined reference to `ib_dealloc_pd'
Fixes: 9533b292a7ac ("IB: remove redundant INFINIBAND kconfig dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
btrfs_read_fs_root_no_name() may return ERR_PTR(-ENOENT) or
ERR_PTR(-ENOMEM) and therefore search_ioctl() and
btrfs_search_path_in_tree() should use PTR_ERR() instead of -ENOENT,
which all other callers of btrfs_read_fs_root_no_name() do.
Drop the error message as it would be confusing, the caller of ioctl
will likely interpret the error code and not look into the syslog.
Signed-off-by: Tomohiro Misono <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
I got a report that after upgrading to 4.16, someone's filesystems
weren't mounting:
[ 23.845852] BTRFS info (device loop0): unrecognized mount option 'subvol='
Before 4.16, this mounted the default subvolume. It turns out that this
empty "subvol=" is actually an application bug, but it was causing the
application to fail, so it's an ABI break if you squint.
The generic parsing code we use for mount options (match_token())
doesn't match an empty string as "%s". Previously, setup_root_args()
removed the "subvol=" string, but the mount path was cleaned up to not
need that. Add a dummy Opt_subvol_empty to fix this.
The simple workaround is to use / or . for the value of 'subvol=' .
Fixes: 312c89fbca06 ("btrfs: cleanup btrfs_mount() using btrfs_mount_root()")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Looks like the original idea was to print the hex of the flags which is
not coded with their flag name. So use the current buf pointer bp
instead of buf.
Reaching the uknown flags should never happen, it's there just in case.
Fixes: ebce0e01b930b ("btrfs: make block group flags in balance printks human-readable")
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The dedupe range is 16 MiB, with 4 KiB pages and 8 byte pointers, the
arrays can be 32KiB large. To avoid allocation failures due to
fragmented memory, use the allocation with fallback to vmalloc.
The arrays are allocated and freed only inside btrfs_extent_same and
reused for all the ranges.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We support big dedup requests by splitting range to smaller parts, and
call dedupe logic on each of them.
Instead of repeated allocation and deallocation, allocate once at the
beginning and reuse in the iteration.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently btrfs_dedupe_file_range silently restricts the dedupe range to
to 16MiB to limit locking and working memory size and is documented in
manual page as implementation specific.
Let's remove that restriction by iterating over the dedup range in 16MiB
steps. This is backward compatible and will not change anything for
requests smaller then 16MiB.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Split btrfs_extent_same() to two parts where one is the main EXTENT_SAME
entry and a helper that can be repeatedly called on a range. This will
be used in following patches.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_link() calls btrfs_orphan_del() if it's linking an O_TMPFILE but
it doesn't reserve space to do so. Even before the removal of the
orphan_block_rsv it wasn't using it.
Fixes: ef3b9af50bfa ("Btrfs: implement inode_operations callback tmpfile")
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We got rid of BTRFS_INODE_HAS_ORPHAN_ITEM and
BTRFS_INODE_ORPHAN_META_RESERVED, so we can renumber the flags to make
them consecutive again.
Signed-off-by: Omar Sandoval <osandov@fb.com>
[ switch them enums so we don't have to do that again ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Now that we don't keep long-standing reservations for orphan items,
root->orphan_block_rsv isn't used. We can git rid of it, along with:
- root->orphan_lock, which was used to protect root->orphan_block_rsv
- root->orphan_inodes, which was used as a refcount for root->orphan_block_rsv
- BTRFS_INODE_ORPHAN_META_RESERVED, which was used to track reservations
in root->orphan_block_rsv
- btrfs_orphan_commit_root(), which was the last user of any of these
and does nothing else
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, we keep space reserved for all inode orphan items until the
inode is evicted (i.e., all references to it are dropped). We hit an
issue where an application would keep a bunch of deleted files open (by
design) and thus keep a large amount of space reserved, causing ENOSPC
errors when other operations tried to reserve space. This long-standing
reservation isn't absolutely necessary for a couple of reasons:
- We can almost always make the reservation we need or steal from the
global reserve for the orphan item
- If we can't, it's not the end of the world if we drop the orphan item
on the floor and let the next mount clean it up
So, get rid of persistent reservation and just reserve space in
btrfs_evict_inode().
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The truncate loop in btrfs_evict_inode() does two things at once:
- It refills the temporary block reserve, potentially stealing from the
global reserve or committing
- It calls btrfs_truncate_inode_items()
The tangle of continues hides the fact that these two steps are actually
separate. Split the first step out into a separate function both for
clarity and so that we can reuse it in a later patch.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb050941b ("Btrfs: Cache free inode numbers in memory")
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_orphan_commit_root() tries to delete an orphan item for a
subvolume in the tree root, but we don't actually insert that item in
the first place. See commit 0a0d4415e338 ("Btrfs: delete dead code in
btrfs_orphan_add()"). We can get rid of it.
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Now that we don't add orphan items for truncate, there can't be races on
adding or deleting an orphan item, so this bit is unnecessary.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, we insert an orphan item during a truncate so that if there's
a crash, we don't leak extents past the on-disk i_size. However, since
commit 7f4f6e0a3f6d ("Btrfs: only update disk_i_size as we remove
extents"), we keep disk_i_size in sync with the extent items as we
truncate, so orphan cleanup will never have any extents to remove. Don't
bother with the superfluous orphan item.
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_free_extent() can fail because of ENOMEM. There's no reason to
panic here, we can just abort the transaction.
Fixes: f4b9aa8d3b87 ("btrfs_truncate")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_truncate_inode_items() uses two variables for error handling, ret
and err. These are not handled consistently, leading to a couple of
bugs.
- Errors from btrfs_del_items() are handled but not propagated to the
caller
- If btrfs_run_delayed_refs() fails and aborts the transaction, we
continue running
Just use ret everywhere and simplify things a bit, fixing both of these
issues.
Fixes: 79787eaab461 ("btrfs: replace many BUG_ONs with proper error handling")
Fixes: 1262133b8d6f ("Btrfs: account for crcs in delayed ref processing")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Commit a41ad394a03b ("Btrfs: convert to the new truncate sequence")
changed btrfs_setsize() to call truncate_setsize() instead of
vmtruncate() but didn't update the comment above it. truncate_setsize()
never fails (the IS_SWAPFILE() check happens elsewhere), so remove the
comment.
Additionally, the comment above btrfs_page_mkwrite() references
vmtruncate(), but truncate_setsize() does the size write and page
locking now.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
select_delayed_ref really just gets the next delayed ref which has to
be processed - either an add ref or drop ref. We never go back for
anything. So the comment is actually bogus, just remove it.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Deletion of a subvolume by rmdir(2) has become allowed by the
'commit cd2decf640b1 ("btrfs: Allow rmdir(2) to delete an empty
subvolume")'.
It is a kind of new feature and this commits add a sysfs entry
/sys/fs/btrfs/features/rmdir_subvol
to indicate the availability of the feature so that a user program
(e.g. fstests) can detect it.
Prior to this commit, all entries in /sys/fs/btrfs/features are feature
which depend on feature bits of superblock (i.e. each feature affects
on-disk format) and managed by attribute_group "btrfs_feature_attr_group".
For each fs, entries in /sys/fs/btrfs/UUID/features indicate which
features are enabled (or can be changed online) for the fs.
However, rmdir_subvol feature only depends on kernel module. Therefore
new attribute_group "btrfs_static_feature_attr_group" is introduced and
sysfs_merge_group() is used to share /sys/fs/btrfs/features directory.
Features in "btrfs_static_feature_attr_group" won't be listed in each
/sys/fs/btrfs/UUID/features.
Signed-off-by: Tomohiro Misono <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Use existing named values instead of the raw numbers.
Signed-off-by: Tomohiro Misono <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Kernel logs are very important for the forensic investigations of the
issues in general make it easy to use it. This patch adds 'balance:'
prefix so that it can be easily searched.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
* The simple 'flags' refer to the btrfs inode
* ... that's in 'binode
* the FS_*_FL variables are 'fsflags'
* the old copies of the variable are prefixed by 'old_'
* Struct inode flags contain 'i_flags'.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The new ioctl is an extension to the FS_IOC_SETFLAGS and adds new
flags and is extensible. Don't get fooled by the XATTR in the name, it
does not have anything in common with the extended attributes,
incidentally also abbreviated as XATTRs.
This patch allows to set the xflags portion of the fsxattr structure,
other items have no meaning and non-zero values will result in
EOPNOTSUPP.
Currently supported xflags:
- APPEND
- IMMUTABLE
- NOATIME
- NODUMP
- SYNC
The structure of btrfs_ioctl_fssetxattr copies btrfs_ioctl_setflags but
is simpler on the flag setting side.
The original patch was written by Chandan Jay Sharma but was incomplete
and no further revision has been sent.
Based-on-patches-by: Chandan Jay Sharma <chandansbg@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The new ioctl is an extension to the FS_IOC_GETFLAGS and adds new
flags and is extensible. This patch allows to return the xflags portion
of the fsxattr structure, other items have no meaning for btrfs or can
be added later.
The original patch was written by Chandan Jay Sharma but was incomplete
and no further revision has been sent. Several cleanups were necessary
to avoid confusion with other ioctls, as we have another flavor of
flags.
Based-on-patches-by: Chandan Jay Sharma <chandansbg@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Preparatory work for the FS_IOC_FSGETXATTR ioctl, basic conversions and
checking helpers.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Converts btrfs_inode::flags to the FS_*_FL flags.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The FS_*_FL flags cannot be easily identified by a prefix but we still
need to recognize them so the 'fsflags' should be closer to the naming
scheme but again the 'fs' part sounds like it's a filesystem flag. I
don't have a better idea for now.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The FS_*_FL flags cannot be easily identified by a variable name prefix
but we still need to recognize them so the 'fsflags' should be closer to
the naming scheme but again the 'fs' part sounds like it's a filesystem
flag. I don't have a better idea for now.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The btrfs inode flag flavour is now simply called 'inode flags' and the
vfs inode are i_flags.
Signed-off-by: David Sterba <dsterba@suse.com>
|
