| Age | Commit message (Collapse) | Author |
|---|
|
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Changed "avaiable" to "available" and "interupt" to "interrupt".
Signed-off-by: Jona Crasselt <jona.crasselt@fau.de>
Signed-off-by: Felix Windsheimer <felix.windsheimer@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 wifi module can optionally make use of the IOMMU.
Add binding documentation for phandle to the IOMMU and
the stream id of wifi iommu block.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add missing optional properties in WCN3990 wifi node.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When both regular IO and resync IO happen at the same time,
and if we also need to split regular. Then we can see tasks
hang due to barrier.
1. resync thread
[ 1463.757205] INFO: task md1_resync:5215 blocked for more than 480 seconds.
[ 1463.757207] Not tainted 4.19.5-1-default #1
[ 1463.757209] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1463.757212] md1_resync D 0 5215 2 0x80000000
[ 1463.757216] Call Trace:
[ 1463.757223] ? __schedule+0x29a/0x880
[ 1463.757231] ? raise_barrier+0x8d/0x140 [raid10]
[ 1463.757236] schedule+0x78/0x110
[ 1463.757243] raise_barrier+0x8d/0x140 [raid10]
[ 1463.757248] ? wait_woken+0x80/0x80
[ 1463.757257] raid10_sync_request+0x1f6/0x1e30 [raid10]
[ 1463.757265] ? _raw_spin_unlock_irq+0x22/0x40
[ 1463.757284] ? is_mddev_idle+0x125/0x137 [md_mod]
[ 1463.757302] md_do_sync.cold.78+0x404/0x969 [md_mod]
[ 1463.757311] ? wait_woken+0x80/0x80
[ 1463.757336] ? md_rdev_init+0xb0/0xb0 [md_mod]
[ 1463.757351] md_thread+0xe9/0x140 [md_mod]
[ 1463.757358] ? _raw_spin_unlock_irqrestore+0x2e/0x60
[ 1463.757364] ? __kthread_parkme+0x4c/0x70
[ 1463.757369] kthread+0x112/0x130
[ 1463.757374] ? kthread_create_worker_on_cpu+0x40/0x40
[ 1463.757380] ret_from_fork+0x3a/0x50
2. regular IO
[ 1463.760679] INFO: task kworker/0:8:5367 blocked for more than 480 seconds.
[ 1463.760683] Not tainted 4.19.5-1-default #1
[ 1463.760684] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1463.760687] kworker/0:8 D 0 5367 2 0x80000000
[ 1463.760718] Workqueue: md submit_flushes [md_mod]
[ 1463.760721] Call Trace:
[ 1463.760731] ? __schedule+0x29a/0x880
[ 1463.760741] ? wait_barrier+0xdd/0x170 [raid10]
[ 1463.760746] schedule+0x78/0x110
[ 1463.760753] wait_barrier+0xdd/0x170 [raid10]
[ 1463.760761] ? wait_woken+0x80/0x80
[ 1463.760768] raid10_write_request+0xf2/0x900 [raid10]
[ 1463.760774] ? wait_woken+0x80/0x80
[ 1463.760778] ? mempool_alloc+0x55/0x160
[ 1463.760795] ? md_write_start+0xa9/0x270 [md_mod]
[ 1463.760801] ? try_to_wake_up+0x44/0x470
[ 1463.760810] raid10_make_request+0xc1/0x120 [raid10]
[ 1463.760816] ? wait_woken+0x80/0x80
[ 1463.760831] md_handle_request+0x121/0x190 [md_mod]
[ 1463.760851] md_make_request+0x78/0x190 [md_mod]
[ 1463.760860] generic_make_request+0x1c6/0x470
[ 1463.760870] raid10_write_request+0x77a/0x900 [raid10]
[ 1463.760875] ? wait_woken+0x80/0x80
[ 1463.760879] ? mempool_alloc+0x55/0x160
[ 1463.760895] ? md_write_start+0xa9/0x270 [md_mod]
[ 1463.760904] raid10_make_request+0xc1/0x120 [raid10]
[ 1463.760910] ? wait_woken+0x80/0x80
[ 1463.760926] md_handle_request+0x121/0x190 [md_mod]
[ 1463.760931] ? _raw_spin_unlock_irq+0x22/0x40
[ 1463.760936] ? finish_task_switch+0x74/0x260
[ 1463.760954] submit_flushes+0x21/0x40 [md_mod]
So resync io is waiting for regular write io to complete to
decrease nr_pending (conf->barrier++ is called before waiting).
The regular write io splits another bio after call wait_barrier
which call nr_pending++, then the splitted bio would continue
with raid10_write_request -> wait_barrier, so the splitted bio
has to wait for barrier to be zero, then deadlock happens as
follows.
resync io regular io
raise_barrier
wait_barrier
generic_make_request
wait_barrier
To resolve the issue, we need to call allow_barrier to decrease
nr_pending before generic_make_request since regular IO is not
issued to underlying devices, and wait_barrier is called again
to ensure no internal IO happening.
Fixes: fc9977dd069e ("md/raid10: simplify the splitting of requests.")
Reported-and-tested-by: Siniša Bandin <sinisa@4net.rs>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Both raid10_read_request and raid10_write_request share
the same code at the beginning of them, so introduce
regular_request_wait to clean up code, and call it in
both request functions.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
mempool_destroy() can handle NULL pointer correctly,
so there is no need to check NULL pointer before calling
mempool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
This is helpful for systems where fast startup time is important.
It is especially nice to avoid benchmarking RAID functions that are
never used (for example, BTRFS selects RAID6_PQ even if the parity RAID
mode is not in use).
This saves 250+ milliseconds of boot time on modern x86 and ARM systems
with a dozen or more available implementations.
The new option is defaulted to 'y' to match the previous behavior of
always benchmarking on init.
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Sort the list of RAID6 algorithms in roughly decreasing order of
expected performance: newer instruction sets first (within each
architecture) and wider unrollings first.
This doesn't make any difference right now, since all functions are
benchmarked; a follow-up change will make use of this by optionally
choosing the first valid function rather than testing all of them.
The Itanium raid6_intx{16,32} entries are also moved down to be near the
other raid6_intx entries for clarity.
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Allow the x86 SSSE3 recovery function to be tested in raid6test.
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
This is defined in glibc's sys/cdefs.h on my system with the same
definition as the raid6test fallback definition. Add a #ifndef check to
avoid a compiler warning about redefining it.
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Add #include <sys/time.h> for gettimeofday() to fix the compiler warning
about an implicitly defined functions.
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/md/md.c: In function 'md_integrity_add_rdev':
drivers/md/md.c:2149:24: warning:
variable 'bi_rdev' set but not used [-Wunused-but-set-variable]
It not used any more after commit
1501efadc524 ("md/raid: only permit hot-add of compatible integrity profiles")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns when an implicit conversion is done between enumerated
types:
drivers/block/drbd/drbd_state.c:708:8: warning: implicit conversion from
enumeration type 'enum drbd_ret_code' to different enumeration type
'enum drbd_state_rv' [-Wenum-conversion]
rv = ERR_INTR;
~ ^~~~~~~~
drbd_request_detach_interruptible's only call site is in the return
statement of adm_detach, which returns an int. Change the return type of
drbd_request_detach_interruptible to match, silencing Clang's warning.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There are several warnings from Clang about no case statement matching
the constant 0:
In file included from drivers/block/drbd/drbd_receiver.c:48:
In file included from drivers/block/drbd/drbd_int.h:48:
In file included from ./include/linux/drbd_genl_api.h:54:
In file included from ./include/linux/genl_magic_struct.h:236:
./include/linux/drbd_genl.h:321:1: warning: no case matching constant
switch condition '0'
GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/genl_magic_struct.h:220:10: note: expanded from macro
'GENL_struct'
switch (0) {
^
Silence this warning by adding a 'case 0:' statement. Additionally,
adjust the alignment of the statements in the ct_assert_unique macro to
avoid a checkpatch warning.
This solution was originally sent by Arnd Bergmann with a default case
statement: https://lore.kernel.org/patchwork/patch/756723/
Link: https://github.com/ClangBuiltLinux/linux/issues/43
Suggested-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
And also re-enable partial-zero-out + discard aligned.
With the introduction of REQ_OP_WRITE_ZEROES,
we started to use that for both WRITE_ZEROES and DISCARDS,
hoping that WRITE_ZEROES would "do what we want",
UNMAP if possible, zero-out the rest.
The example scenario is some LVM "thin" backend.
While an un-allocated block on dm-thin reads as zeroes, on a dm-thin
with "skip_block_zeroing=true", after a partial block write allocated
that block, that same block may well map "undefined old garbage" from
the backends on LBAs that have not yet been written to.
If we cannot distinguish between zero-out and discard on the receiving
side, to avoid "undefined old garbage" to pop up randomly at later times
on supposedly zero-initialized blocks, we'd need to map all discards to
zero-out on the receiving side. But that would potentially do a full
alloc on thinly provisioned backends, even when the expectation was to
unmap/trim/discard/de-allocate.
We need to distinguish on the protocol level, whether we need to guarantee
zeroes (and thus use zero-out, potentially doing the mentioned full-alloc),
or if we want to put the emphasis on discard, and only do a "best effort
zeroing" (by "discarding" blocks aligned to discard-granularity, and zeroing
only potential unaligned head and tail clippings to at least *try* to
avoid "false positives" in an online-verify later), hoping that someone
set skip_block_zeroing=false.
For some discussion regarding this on dm-devel, see also
https://www.mail-archive.com/dm-devel%40redhat.com/msg07965.html
https://www.redhat.com/archives/dm-devel/2018-January/msg00271.html
For backward compatibility, P_TRIM means zero-out, unless the
DRBD_FF_WZEROES feature flag is agreed upon during handshake.
To have upper layers even try to submit WRITE ZEROES requests,
we need to announce "efficient zeroout" independently.
We need to fixup max_write_zeroes_sectors after blk_queue_stack_limits():
if we can handle "zeroes" efficiently on the protocol,
we want to do that, even if our backend does not announce
max_write_zeroes_sectors itself.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If you try to promote a Secondary while connected to a Primary
and allow-two-primaries is NOT set, we will wait for "ping-timeout"
to give this node a chance to detect a dead primary,
in case the cluster manager noticed faster than we did.
But if we then are *still* connected to a Primary,
we fail (after an additional timeout of ping-timout).
This change skips the spurious second timeout.
Most people won't notice really,
since "ping-timeout" by default is half a second.
But in some installations, ping-timeout may be 10 or 20 seconds or more,
and spuriously delaying the error return becomes annoying.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
emma: "Unexpected data packet AuthChallenge (0x0010)"
ava: "expected AuthChallenge packet, received: ReportProtocol (0x000b)"
"Authentication of peer failed, trying again."
Pattern repeats.
There is no point in retrying the handshake,
if we expect to receive an AuthChallenge,
but the peer is not even configured to expect or use a shared secret.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
print_st_err() is defined with its 4th argument taking an
'enum drbd_state_rv' but its prototype use an int for it.
Fix this by using 'enum drbd_state_rv' in the prototype too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If peers are "simultaneously" told to disconnect from each other,
either explicitly, or implicitly by taking down the resource,
with bad timing, one side may see its disconnect "fail" with
a result of "state change failed by peer", and interpret this as
"please oudate yourself".
Try to catch this by checking for current connection status,
and possibly retry as local-only state change instead.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
"suspending" IO is overloaded.
It can mean "do not allow new requests" (obviously),
but it also may mean "must not complete pending IO",
for example while the fencing handlers do their arbitration.
When adjusting disk options, we suspend io (disallow new requests), then
wait for the activity-log to become unused (drain all IO completions),
and possibly replace it with a new activity log of different size.
If the other "suspend IO" aspect is active, pending IO completions won't
happen, and we would block forever (unkillable drbdsetup process).
Fix this by skipping the activity log adjustment if the "al-extents"
setting did not change. Also, in case it did change, fail early without
blocking if it looks like we would block forever.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Multiple failure scenario:
a) all good
Connected Primary/Secondary UpToDate/UpToDate
b) lose disk on Primary,
Connected Primary/Secondary Diskless/UpToDate
c) continue to write to the device,
changes only make it to the Secondary storage.
d) lose disk on Secondary,
Connected Primary/Secondary Diskless/Diskless
e) now try to re-attach on Primary
This would have succeeded before, even though that is clearly the
wrong data set to attach to (missing the modifications from c).
Because we only compared our "effective" and the "to-be-attached"
data generation uuid tags if (device->state.conn < C_CONNECTED).
Fix: change that constraint to (device->state.pdsk != D_UP_TO_DATE)
compare the uuids, and reject the attach.
This patch also tries to improve the reverse scenario:
first lose Secondary, then Primary disk,
then try to attach the disk on Secondary.
Before this patch, the attach on the Secondary succeeds, but since commit
drbd: disconnect, if the wrong UUIDs are attached on a connected peer
the Primary will notice unsuitable data, and drop the connection hard.
Though unfortunately at a point in time during the handshake where
we cannot easily abort the attach on the peer without more
refactoring of the handshake.
We now reject any attach to "unsuitable" uuids,
as long as we can see a Primary role,
unless we already have access to "good" data.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we would reject a new handshake, if the peer had attached first,
and then connected, we should force disconnect if the peer first connects,
and only then attaches.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we attach a (consistent) backing device,
which knows about a last-agreed effective size,
and that effective size is *larger* than the currently requested size,
we refused to attach with ERR_DISK_TOO_SMALL
Failure: (111) Low.dev. smaller than requested DRBD-dev. size.
which is confusing to say the least.
This patch changes the error code in that case to ERR_IMPLICIT_SHRINK
Failure: (170) Implicit device shrinking not allowed. See kernel log.
additional info from kernel:
To-be-attached device has last effective > current size, and is consistent
(9999 > 7777 sectors). Refusing to attach.
It also allows to attach with an explicit size.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
With "on-no-data-accessible suspend-io", DRBD requires the next attach
or connect to be to the very same data generation uuid tag it lost last.
If we first lost connection to the peer,
then later lost connection to our own disk,
we would usually refuse to re-connect to the peer,
because it presents the wrong data set.
However, if the peer first connects without a disk,
and then attached its disk, we accepted that same wrong data set,
which would be "unexpected" by any user of that DRBD
and cause "undefined results" (read: very likely data corruption).
The fix is to forcefully disconnect as soon as we notice that the peer
attached to the "wrong" dataset.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During handshake, if we are diskless ourselves, we used to accept any size
presented by the peer.
Which could be zero if that peer was just brought up and connected
to us without having a disk attached first, in which case both
peers would just "flip" their volume sizes.
Now, even a diskless node will ignore "zero" sizes
presented by a diskless peer.
Also a currently Diskless Primary will refuse to shrink during handshake:
it may be frozen, and waiting for a "suitable" local disk or peer to
re-appear (on-no-data-accessible suspend-io). If the peer is smaller
than what we used to be, it is not suitable.
The logic for a diskless node during handshake is now supposed to be:
believe the peer, if
- I don't have a current size myself
- we agree on the size anyways
- I do have a current size, am Secondary, and he has the only disk
- I do have a current size, am Primary, and he has the only disk,
which is larger than my current size
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previously, some implicit resizes that happend during handshake
have not been reported as prominently as explicit resize.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
So far there was the possibility that we called
genlmsg_new(GFP_NOIO)/mutex_lock() while holding an rcu_read_lock().
This included cases like:
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
drbd_bcast_event
genlmsg_new(GFP_NOIO) --> may sleep
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
notify_helper
genlmsg_new(GFP_NOIO) --> may sleep
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
notify_helper
mutex_lock --> may sleep
While using GFP_ATOMIC whould have been possible in the first two cases,
the real fix is to narrow the rcu_read_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The cleanup in commit 356da6d0cde3 ("dma-mapping: bypass indirect calls
for dma-direct") accidentally inverted the logic in the check for the
presence of a ->dma_supported() callback. Switch this back to the way it
was to prevent a crash on boot.
Fixes: 356da6d0cde3 ("dma-mapping: bypass indirect calls for dma-direct")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea95 ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reverts commit d9678adbe733a770428a98651beaa2817d503ed3.
Received below report from Stefan.
Revert the commit until CAAM driver dependency cycles are fixed.
this patch in next-20181214 breaks "make modules_install" for
arm64/defconfig on my Ubuntu machine:
DEPMOD 4.20.0-rc6-next-20181214
depmod: ERROR: Found 6 modules in dependency cycles!
depmod: ERROR: Cycle detected: caamalg_desc -> dpaa2_caam -> authenc
depmod: ERROR: Cycle detected: caamalg_desc -> dpaa2_caam -> fsl_mc_dpio
depmod: ERROR: Cycle detected: dpaa2_caam -> caamhash_desc -> dpaa2_caam
depmod: ERROR: Cycle detected: caamalg_desc -> dpaa2_caam -> caamhash_desc -> error
depmod: ERROR: Cycle detected: caamalg_desc -> dpaa2_caam -> caamhash_desc -> caamalg_desc
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC Fixes for v4.20
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
* tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: draak: Fix CVBS input
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
|
|
Separate just the changing of mount flags (MS_REMOUNT|MS_BIND) from full
remount because the mount data will get parsed with the new fs_context
stuff prior to doing a remount - and this causes the syscall to fail under
some circumstances.
To quote Eric's explanation:
[...] mount(..., MS_REMOUNT|MS_BIND, ...) now validates the mount options
string, which breaks systemd unit files with ProtectControlGroups=yes
(e.g. systemd-networkd.service) when systemd does the following to
change a cgroup (v1) mount to read-only:
mount(NULL, "/run/systemd/unit-root/sys/fs/cgroup/systemd", NULL,
MS_RDONLY|MS_NOSUID|MS_NODEV|MS_NOEXEC|MS_REMOUNT|MS_BIND, NULL)
... when the kernel has CONFIG_CGROUPS=y but no cgroup subsystems
enabled, since in that case the error "cgroup1: Need name or subsystem
set" is hit when the mount options string is empty.
Probably it doesn't make sense to validate the mount options string at
all in the MS_REMOUNT|MS_BIND case, though maybe you had something else
in mind.
This is also worthwhile doing because we will need to add a mount_setattr()
syscall to take over the remount-bind function.
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
|
