| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control fixes here. All of them are driver fixes, the Intel
Cherryview being the most interesting one.
- Fix a mux problem for I2C in the MVEBU driver.
- Fix a really hairy inversion problem in the Intel Cherryview
driver.
- Fix the register for the sdc2_clk in the Qualcomm SM8250 driver.
- Check the virtual GPIO boot failur in the Mediatek driver"
* tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: check mtk_is_virt_gpio input parameter
pinctrl: qcom: sm8250: correct sdc2_clk
pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
pinctrl: mvebu: Fix i2c sda definition for 98DX3236
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo
Pieralisi)
- Add Pali Rohár as aardvark PCI maintainer (Pali Rohár)
* tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer
PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches in driver frameworks. The iscsi one corrects a bug induced
by a BPF change to network locking and the other is a regression we
introduced"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
|
|
Pull io_uring fixes from Jens Axboe:
- fix for async buffered reads if read-ahead is fully disabled (Hao)
- double poll match fix
- ->show_fdinfo() potential ABBA deadlock complaint fix
* tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
io_uring: fix async buffered reads when readahead is disabled
io_uring: fix potential ABBA deadlock in ->show_fdinfo()
io_uring: always delete double poll wait entry on match
|
|
Pull block fix from Jens Axboe:
"Single fix for a ->commit_rqs failure case"
* tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
blk-mq: call commit_rqs while list empty but error happen
|
|
Extend the current page table dump support in RISC-V to include efi
pages as well.
Here is the output of efi runtime page table mappings.
---[ UEFI runtime start ]---
0x0000000020002000-0x0000000020003000 0x00000000be732000 4K PTE D A . . . W R V
0x0000000020018000-0x0000000020019000 0x00000000be738000 4K PTE D A . . . W R V
0x000000002002c000-0x000000002002d000 0x00000000be73c000 4K PTE D A . . . W R V
0x0000000020031000-0x0000000020032000 0x00000000bff61000 4K PTE D A . . X W R V
---[ UEFI runtime end ]---
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
This patch adds EFI runtime service support for RISC-V.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
[ardb: - Remove the page check]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add a RISC-V architecture specific stub code that actually copies the
actual kernel image to a valid address and jump to it after boot services
are terminated. Enable UEFI related kernel configs as well for RISC-V.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Link: https://lore.kernel.org/r/20200421033336.9663-4-atish.patra@wdc.com
[ardb: - move hartid fetch into check_platform_features()
- use image_size not reserve_size
- select ISA_C
- do not use dram_base]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Linux kernel Image can appear as an EFI application With appropriate
PE/COFF header fields in the beginning of the Image header. An EFI
application loader can directly load a Linux kernel Image and an EFI
stub residing in kernel can boot Linux kernel directly.
Add the necessary PE/COFF header.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Link: https://lore.kernel.org/r/20200421033336.9663-3-atish.patra@wdc.com
[ardb: - use C prefix for c.li to ensure the expected opcode is emitted
- align all image sections according to PE/COFF section alignment ]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Currently, page table setup is done during setup_va_final where fixmap can
be used to create the temporary mappings. The physical frame is allocated
from memblock_alloc_* functions. However, this won't work if page table
mapping needs to be created for a different mm context (i.e. efi mm) at
a later point of time.
Use generic kernel page allocation function & macros for any mapping
after setup_vm_final.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
UEFI uses early IO or memory mappings for runtime services before
normal ioremap() is usable. Add the necessary fixmap bindings and
pmd mappings for generic ioremap support to work.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Currently, RISC-V reserves 1MB of fixmap memory for device tree. However,
it maps only single PMD (2MB) space for fixmap which leaves only < 1MB space
left for other kernel features such as early ioremap which requires fixmap
as well. The fixmap size can be increased by another 2MB but it brings
additional complexity and changes the virtual memory layout as well.
If we require some additional feature requiring fixmap again, it has to be
moved again.
Technically, DT doesn't need a fixmap as the memory occupied by the DT is
only used during boot. That's why, We map device tree in early page table
using two consecutive PGD mappings at lower addresses (< PAGE_OFFSET).
This frees lot of space in fixmap and also makes maximum supported
device tree size supported as PGDIR_SIZE. Thus, init memory section can be used
for the same purpose as well. This simplifies fixmap implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/efi/efi into for-next
Stable branch for v5.10 shared between the EFI and RISC-V trees
The RISC-V EFI boot and runtime support will be merged for v5.10 via
the RISC-V tree. However, it incorporates some changes that conflict
with other EFI changes that are in flight, so this tag serves as a
shared base that allows those conflicts to be resolved beforehand.
* tag 'efi-riscv-shared-for-v5.10' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/libstub: arm32: Use low allocation for the uncompressed kernel
efi/libstub: Export efi_low_alloc_above() to other units
efi/libstub: arm32: Base FDT and initrd placement on image address
efi: Rename arm-init to efi-init common for all arch
include: pe.h: Add RISC-V related PE definition
|
|
s3c64xx_spi_hwinit() disables interrupts. In s3c64xx_spi_probe() after
calling s3c64xx_spi_hwinit() they are enabled with the following call.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-10-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Increase timeout by 30 ms for some wiggle room and set the minimum value
to 100 ms. This ensures a non-zero value for short transfers which
may take less than 1 ms. The timeout value does not affect
performance because it is used with a completion.
Similar formula is used in other drivers e.g. sun4i, sun6i.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-9-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make sure the cur_speed value used in s3c64xx_enable_datapath()
to configure DMA channel and in s3c64xx_wait_for_*() to calculate the
transfer timeout is set to the actual value of (half) the clock speed.
Don't change non-CMU case, because no frequency calculation errors have
been reported.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-8-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove descriptions for non-existent fields and fix indentation.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-7-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename S3C64XX_SPI_SLAVE_* to S3C64XX_SPI_CS_* to match documentation.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-6-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Report amount of pending data when a transfer stops due to errors.
Report if DMA was used to transfer data and print the status code.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-5-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Check return values in prepare_dma() and s3c64xx_spi_config() and
propagate errors upwards.
Fixes: 788437273fa8 ("spi: s3c64xx: move to generic dmaengine API")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-4-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail.
The vendor kernel for ARTIK5 handles CS in a simmilar way.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-3-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail to complete. This solution to the problem
is found in the vendor kernel for ARTIK5 boards based on Exynos3250.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-2-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch enables ACPI support in qoriq ahci driver.
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Simplify the return expression.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add Intel Rocket Lake PCH-H RAID PCI IDs to the list of supported
controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The file zero-page.txt does not exit. Add links to zero-page.rst
instead.
[ bp: Massage a bit. ]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201002190623.7489-1-xypron.glpk@gmx.de
|
|
Florian Fainelli says:
====================
net: dsa: Improve dsa_untag_bridge_pvid()
This patch series is based on the recent discussions with Vladimir:
https://lore.kernel.org/netdev/20201001030623.343535-1-f.fainelli@gmail.com/
the simplest way forward was to call dsa_untag_bridge_pvid() after
eth_type_trans() has been set which guarantees that skb->protocol is set
to a correct value and this allows us to utilize
__vlan_find_dev_deep_rcu() properly without playing or using the bridge
master as a net_device reference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we are guaranteed that dsa_untag_bridge_pvid() is called after
eth_type_trans() we can utilize __vlan_find_dev_deep_rcu() which will
take care of finding an 802.1Q upper on top of a bridge master.
A common use case, prior to 12a1526d067 ("net: dsa: untag the bridge
pvid from rx skbs") was to configure a bridge 802.1Q upper like this:
ip link add name br0 type bridge vlan_filtering 0
ip link add link br0 name br0.1 type vlan id 1
in order to pop the default_pvid VLAN tag.
With this change we restore that behavior while still allowing the DSA
receive path to automatically pop the VLAN tag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that dsa_untag_bridge_pvid() is called after eth_type_trans() we are
guaranteed that skb->protocol will be set to a correct value, thus
allowing us to avoid calling vlan_eth_hdr().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since bcache code was merged into mainline kerrnel, each cache set only
as one single cache in it. The multiple caches framework is here but the
code is far from completed. Considering the multiple copies of cached
data can also be stored on e.g. md raid1 devices, it is unnecessary to
support multiple caches in one cache set indeed.
The previous preparation patches fix the dependencies of explicitly
making a cache set only have single cache. Now we don't have to maintain
an embedded partial super block in struct cache_set, the in-memory super
block can be directly referenced from struct cache.
This patch removes the embedded struct cache_sb from struct cache_set,
and fixes all locations where the superb lock was referenced from this
removed super block by referencing the in-memory super block of struct
cache.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently the cache's sync status is checked and set on cache set's in-
memory partial super block. After removing the embedded struct cache_sb
from cache set and reference cache's in-memory super block from struct
cache_set, the sync status can set and check directly on cache's super
block.
This patch checks and sets the cache sync status directly on cache's
in-memory super block. This is a preparation for later removing embedded
struct cache_sb from struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After removing the embedded struct cache_sb from struct cache_set, cache
set will directly reference the in-memory super block of struct cache.
It is unnecessary to compare block_size, bucket_size and nr_in_set from
the identical in-memory super block in can_attach_cache().
This is a preparation patch for latter removing cache_set->sb from
struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In order to update the partial super block of cache set, the seq numbers
of cache and cache set are checked in register_cache_set(). If cache's
seq number is larger than cache set's seq number, cache set must update
its partial super block from cache's super block. It is unncessary when
the embedded struct cache_sb is removed from struct cache set.
This patch removed the seq numbers checking from register_cache_set(),
because later there will be no such partial super block in struct cache
set, the cache set will directly reference in-memory super block from
struct cache. This is a preparation patch for removing embedded struct
cache_sb from struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Because struct cache_set and struct cache both have struct cache_sb,
macro bucket_bytes() currently are used on both of them. When removing
the embedded struct cache_sb from struct cache_set, this macro won't be
used on struct cache_set anymore.
This patch unifies all bucket_bytes() usage only on struct cache, this is
one of the preparation to remove the embedded struct cache_sb from
struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It seems alloc_bucket_pages() is the only user of bucket_pages().
Considering alloc_bucket_pages() is removed from bcache code, it is safe
to remove the useless macro bucket_pages() now.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now no one uses alloc_bucket_pages() anymore, remove it from bcache.h.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Because struct cache_set and struct cache both have struct cache_sb,
therefore macro block_bytes() can be used on both of them. When removing
the embedded struct cache_sb from struct cache_set, this macro won't be
used on struct cache_set anymore.
This patch unifies all block_bytes() usage only on struct cache, this is
one of the preparation to remove the embedded struct cache_sb from
struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch adds a separated set_uuid[16] in struct cache_set, to store
the uuid of the cache set. This is the preparation to remove the
embedded struct cache_sb from struct cache_set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since now each cache_set explicitly has single cache, for_each_cache()
is unnecessary. This patch removes this macro, and update all locations
where it is used, and makes sure all code logic still being consistent.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently although the bcache code has a framework for multiple caches
in a cache set, but indeed the multiple caches never completed and users
use md raid1 for multiple copies of the cached data.
This patch does the following change in struct cache_set, to explicitly
make a cache_set only have single cache,
- Change pointer array "*cache[MAX_CACHES_PER_SET]" to a single pointer
"*cache".
- Remove pointer array "*cache_by_alloc[MAX_CACHES_PER_SET]".
- Remove "caches_loaded".
Now the code looks as exactly what it does in practic: only one cache is
used in the cache set.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The parameter 'int n' from bch_bucket_alloc_set() is not cleared
defined. From the code comments n is the number of buckets to alloc, but
from the code itself 'n' is the maximum cache to iterate. Indeed all the
locations where bch_bucket_alloc_set() is called, 'n' is alwasy 1.
This patch removes the confused and unnecessary 'int n' from parameter
list of bch_bucket_alloc_set(), and explicitly allocates only 1 bucket
for its caller.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
As inode->iprivate equals to third parameter of
debugfs_create_file() which is NULL. So it's equivalent
to original code logic.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In mca_reserve(c) macro, we are checking root whether is NULL or not.
But that's not enough, when we read the root node in run_cache_set(),
if we got an error in bch_btree_node_read_done(), we will return
ERR_PTR(-EIO) to c->root.
And then we will go continue to unregister, but before calling
unregister_shrinker(&c->shrink), there is a possibility to call
bch_mca_count(), and we would get a crash with call trace like that:
[ 2149.876008] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000b5
... ...
[ 2150.598931] Call trace:
[ 2150.606439] bch_mca_count+0x58/0x98 [escache]
[ 2150.615866] do_shrink_slab+0x54/0x310
[ 2150.624429] shrink_slab+0x248/0x2d0
[ 2150.632633] drop_slab_node+0x54/0x88
[ 2150.640746] drop_slab+0x50/0x88
[ 2150.648228] drop_caches_sysctl_handler+0xf0/0x118
[ 2150.657219] proc_sys_call_handler.isra.18+0xb8/0x110
[ 2150.666342] proc_sys_write+0x40/0x50
[ 2150.673889] __vfs_write+0x48/0x90
[ 2150.681095] vfs_write+0xac/0x1b8
[ 2150.688145] ksys_write+0x6c/0xd0
[ 2150.695127] __arm64_sys_write+0x24/0x30
[ 2150.702749] el0_svc_handler+0xa0/0x128
[ 2150.710296] el0_svc+0x8/0xc
Signed-off-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previously the experimental async registration uses a separate sysfs
file register_async. Now the async registration code seems working well
for a while, we can do furtuher testing with it now.
This patch changes the async bcache registration shares the same sysfs
file /sys/fs/bcache/register (and register_quiet). Async registration
will be default behavior if BCACHE_ASYNC_REGISTRATION is set in kernel
configure. By default, BCACHE_ASYNC_REGISTRATION is not configured yet.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-10-02
1) Add a full xfrm compatible layer for 32-bit applications on
64-bit kernels. From Dmitry Safonov.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ Upstream commit a95bc734e60449e7b073ff7ff70c35083b290ae9 ]
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aadd6 ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<codrin.ciubotariu@microchip.com>:
The Sony/Philips Digital Interface Receiver (SPDIFRX) is a serial port
compliant with the IEC-60958 standard. Among its caracteristics, we
mention the following:
- SPDIF/AES-EBU Compatible Serial Port
- 32 Samples FIFO
- Data Width Configurable to 24 bits, 20 bits or 16 bits
- Packed and Unpacked Data Support for System Memory Optimization
- Line State Events Report and Source of Interrupt
- Line Error Rate Report
- Full Memory Map of 192 bits for Channel 1 and Channel 2 Status and
User Data
- First 32-bit Status A, Status B Change Report and Source of Interrupt
- Line Digital Filter
- Register Write Protection
- Abnormal Software Access and Internal Sequencer Integrity Check Reports
This interface is available in Microchip's SAMA7G5 SoC.
Codrin Ciubotariu (2):
dt-bindings: sound: add DT bindings for Microchip S/PDIF RX Controller
ASoC: mchp-spdifrx: add driver for SPDIF RX
.../bindings/sound/mchp,spdifrx.yaml | 73 ++
sound/soc/atmel/Kconfig | 13 +
sound/soc/atmel/Makefile | 2 +
sound/soc/atmel/mchp-spdifrx.c | 954 ++++++++++++++++++
4 files changed, 1042 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/mchp,spdifrx.yaml
create mode 100644 sound/soc/atmel/mchp-spdifrx.c
--
2.25.1
|
|
It is likely that this header file is about the WM8523.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201002165908.637809-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
