| Age | Commit message (Collapse) | Author |
|---|
|
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.
Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.
While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability. This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.
If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output. This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats. Always expose counters from all
the rings. Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.
The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c5e ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As noticed by Eric, we need to switch to the helper
dev_change_tx_queue_len() for SIOCSIFTXQLEN call path too,
otheriwse still miss dev_qdisc_change_tx_queue_len().
Fixes: 6a643ddb5624 ("net: introduce helper dev_change_tx_queue_len()")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling skb_unclone() is expensive as it triggers a memcpy operation.
Instead of calling skb_unclone() unconditionally, call it only when skb
has a shared frag_list. This improves tls rx throughout significantly.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Suggested-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pool can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/zatm.c:1491 zatm_ioctl() warn: potential spectre issue
'zatm_dev->pool_info' (local cap)
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-06-29
please apply a few qeth fixes for -net and your 4.17 stable queue.
Patches 1-3 fix several issues wrt to MAC address management that were
introduced during the 4.17 cycle.
Patch 4 tackles a long-standing issue with busy multi-connection workloads
on devices in af_iucv mode.
Patch 5 makes sure to re-enable all active HW offloads, after a card was
previously set offline and thus lost its HW context.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit e830baa9c3f0 ("qeth: restore device features after recovery") and
commit ce3443564145 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If qeth_qdio_output_handler() detects that a transmit requires async
completion, it replaces the pending buffer's metadata object
(qeth_qdio_out_buffer) so that this queue buffer can be re-used while
the data is pending completion.
Later when the CQ indicates async completion of such a metadata object,
qeth_qdio_cq_handler() tries to free any data associated with this
object (since HW has now completed the transfer). By calling
qeth_clear_output_buffer(), it erronously operates on the queue buffer
that _previously_ belonged to this transfer ... but which has been
potentially re-used several times by now.
This results in double-free's of the buffer's data, and failing
transmits as the buffer descriptor is scrubbed in mid-air.
The correct way of handling this situation is to
1. scrub the queue buffer when it is prepared for re-use, and
2. later obtain the data addresses from the async-completion notifier
(ie. the AOB), instead of the queue buffer.
All this only affects qeth devices used for af_iucv HiperTransport.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
*ether_addr*_64bits functions have been introduced to optimize
performance critical paths, which access 6-byte ethernet address as u64
value to get "nice" assembly. A harmless hack works nicely on ethernet
addresses shoved into a structure or a larger buffer, until busted by
Kasan on smth like plain (u8 *)[6].
qeth_l2_set_mac_address calls qeth_l2_remove_mac passing
u8 old_addr[ETH_ALEN] as an argument.
Adding/removing macs for an ethernet adapter is not that performance
critical. Moreover is_multicast_ether_addr_64bits itself on s390 is not
faster than is_multicast_ether_addr:
is_multicast_ether_addr(%r2) -> %r2
llc %r2,0(%r2)
risbg %r2,%r2,63,191,0
is_multicast_ether_addr_64bits(%r2) -> %r2
llgc %r2,0(%r2)
risbg %r2,%r2,63,191,0
So, let's just use is_multicast_ether_addr instead of
is_multicast_ether_addr_64bits.
Fixes: bcacfcbc82b4 ("s390/qeth: fix MAC address update sequence")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When qeth_l2_set_mac_address() finds the card in a non-reachable state,
it merely copies the new MAC address into dev->dev_addr so that
__qeth_l2_set_online() can later register it with the HW.
But __qeth_l2_set_online() may very well be running concurrently, so we
can't trust the card state without appropriate locking:
If the online sequence is past the point where it registers
dev->dev_addr (but not yet in SOFTSETUP state), any address change needs
to be properly programmed into the HW. Otherwise the netdevice ends up
with a different MAC address than what's set in the HW, and inbound
traffic is not forwarded as expected.
This is most likely to occur for OSD in LPAR, where
commit 21b1702af12e ("s390/qeth: improve fallback to random MAC address")
now triggers eg. systemd to immediately change the MAC when the netdevice
is registered with a NET_ADDR_RANDOM address.
Fixes: bcacfcbc82b4 ("s390/qeth: fix MAC address update sequence")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b7493e91c11a757cf0f8ab26989642ee4bb2c642.
On its own, querying RDEV for a MAC address works fine. But when upgrading
from a qeth that previously queried DDEV on a z/VM NIC (ie. any kernel with
commit ec61bd2fd2a2), the RDEV query now returns a _different_ MAC address
than the DDEV query.
If the NIC is configured with MACPROTECT, z/VM apparently requires us to
use the MAC that was initially returned (on DDEV) and registered. So after
upgrading to a kernel that uses RDEV, the SETVMAC registration cmd for the
new MAC address fails and we end up with a non-operabel interface.
To avoid regressions on upgrade, switch back to using DDEV for the MAC
address query. The downgrade path (first RDEV, later DDEV) is fine, in this
case both queries return the same MAC address.
Fixes: b7493e91c11a ("s390/qeth: use Read device to query hypervisor for MAC")
Reported-by: Michal Kubecek <mkubecek@suse.com>
Tested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __alx_open function can be called from ndo_open, which is called
under RTNL, or from alx_resume, which isn't. Since commit d768319cd427,
we're calling the netif_set_real_num_{tx,rx}_queues functions, which
need to be called under RTNL.
This is similar to commit 0c2cc02e571a ("igb: Move the calls to set the
Tx and Rx queues into igb_open").
Fixes: d768319cd427 ("alx: enable multiple tx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: fc7a6c287ff3 ("sfc: use a semaphore to lock farch filters too")
Suggested-by: Joseph Korty <joe.korty@concurrent-rt.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf9a ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create unittests for the tc tunnel_key action.
v2:
For the tests expecting failures, added non-zero exit codes in the
teardowns. This prevents those tests from failing if the act_tunnel_key
module is unloaded.
Signed-off-by: Keara Leibovitz <kleib@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit extends the existing TIPC socket diagnostics framework
for information related to TIPC group communication.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A peer node is considered down if there are no
active links (or) lost contact to the node. In current implementation,
a peer node instance is deleted either if
a) TIPC module is removed (or)
b) Application can use a netlink/iproute2 interface to delete a
specific down node.
Thus, a down node instance lives in the system forever, unless the
application explicitly removes it.
We fix this by deleting the nodes which are down for
a specified amount of time (5 minutes).
Existing node supervision timer is used to achieve this.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The very first version of RTL8169 from 2002 (and only this one) has
support for a TBI 1000BaseX fiber interface. The TBI support in the
driver makes switching to phylib tricky, so best would be to get
rid of it. I found no report from anybody using a device with RTL8169
and fiber interface, also the vendor driver doesn't support this mode
(any longer).
So remove TBI support and bail out with a message if a card with
activated TBI is detected. If there really should be any user of it
out there, we could add a stripped-down version of the driver
supporting chip version 01 and TBI only (and maybe move it to
staging).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In single-link usage, the function tipc_node_timeout() still iterates
over the whole link array to handle each link. Given that the maximum
number of bearers are 3, there are 2 redundant iterations with lock
grab/release. Since this function is executing very frequently it makes
sense to optimize it.
This commit adds conditional checking to exit from the loop if the
known number of configured links has already been accessed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini reported that a recent commit broke prefix routes for linklocal
addresses. The newly added modify_prefix_route is attempting to add a
new prefix route when the ifp priority does not match the route metric
however the check needs to account for the default priority. In addition,
the route add fails because the route already exists, and then the delete
removes the one that exists. Flip the order to do the delete first.
Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tipc_msg_extract() is using skb_clone() to clone inner
messages from a message bundle buffer. Although this method is safe,
it has an undesired effect that each buffer clone inherits the
true-size of the bundling buffer. As a result, the buffer clone
almost always ends up with being copied anyway by the message
validation function. This makes the cloning into a sub-optimization.
In this commit we take the consequence of this realization, and copy
each inner message to a separately allocated buffer up front in the
extraction function.
As a bonus we can now eliminate the two cases where we had to copy
re-routed packets that may potentially go out on the wire again.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I see no need to define a private debug output symbol, let's use the
standard debug output functions instead. In this context also remove
the deprecated PFX define.
The one assertion is wrong IMO anyway, this code path is used also
by chip version 01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ursula Braun says:
====================
smc: pnetid and SMC-D support
SMC requires a configured pnet table to map Ethernet interfaces to
RoCE adapter ports. For s390 there exists hardware support to group
such devices. The first three patches cover the s390 pnetid support,
enabling SMC-R usage on s390 without configuring an extra pnet table.
SMC currently requires RoCE adapters, and uses RDMA-techniques
implemented with IB-verbs. But s390 offers another method for
intra-CEC Shared Memory communication. The following seven patches
implement a solution to run SMC traffic based on intra-CEC DMA,
called SMC-D.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Internal Shared Memory vPCI Adapter.
This driver implements the interfaces of the SMC-D protocol.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds diag support for SMC-D.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch ties together the previous SMC-D patches. It adds support for
SMC-D to the listen and connect functions and, thus, enables SMC-D
support in the SMC code. If a connection supports both SMC-R and SMC-D,
SMC-D is preferred.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data transfer and CDC message headers differ in SMC-R and SMC-D.
This patch adds support for the SMC-D data transfer to the existing SMC
code. It consists of the following:
* SMC-D CDC support
* SMC-D tx support
* SMC-D rx support
The CDC header is stored at the beginning of the receive buffer. Thus, a
rx_offset variable is added for the CDC header offset within the buffer
(0 for SMC-R).
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two types of SMC: SMC-R and SMC-D. These types are signaled
within the CLC messages during the CLC handshake. This patch adds
support for and checks of the SMC type.
Also, SMC-R and SMC-D need to exchange different information during the
CLC handshake. So, this patch extends the current message formats to
support the SMC-D header fields. The Proposal message can contain both
SMC-R and SMC-D information. The Accept and Confirm messages contain
either SMC-R or SMC-D information.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMC-D relies on PNETIDs to find usable SMC-D/ISM devices for a SMC
connection. This patch adds SMC-D/ISM support to the current PNETID
implementation.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMC supports two variants: SMC-R and SMC-D. For data transport, SMC-R
uses RDMA devices, SMC-D uses so-called Internal Shared Memory (ISM)
devices. An ISM device only allows shared memory communication between
SMC instances on the same machine. For example, this allows virtual
machines on the same host to communicate via SMC without RDMA devices.
This patch adds the base infrastructure for SMC-D and ISM devices to
the existing SMC code. It contains the following:
* ISM driver interface:
This interface allows an ISM driver to register ISM devices in SMC. In
the process, the driver provides a set of device ops for each device.
SMC uses these ops to execute SMC specific operations on or transfer
data over the device.
* Core SMC-D link group, connection, and buffer support:
Link groups, SMC connections and SMC buffers (in smc_core) are
extended to support SMC-D.
* SMC type checks:
Some type checks are added to prevent using SMC-R specific code for
SMC-D and vice versa.
To actually use SMC-D, additional changes to pnetid, CLC, CDC, etc. are
required. These are added in follow-up patches.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SMC protocol requires to send a separate consumer cursor update,
if it cannot be piggybacked to updates of the producer cursor.
Currently the decision to send a separate consumer cursor update
just considers the amount of data already received by the socket
program. It does not consider the amount of data already arrived, but
not yet consumed by the receiver. Basing the decision on the
difference between already confirmed and already arrived data
(instead of difference between already confirmed and already consumed
data), may lead to a somewhat earlier consumer cursor update send in
fast unidirectional traffic scenarios, and thus to better throughput.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s390 hardware supports the definition of a so-call Physical NETwork
IDentifier (short PNETID) per network device port. These PNETIDS
can be used to identify network devices that are attached to the same
physical network (broadcast domain).
On s390 try to use the PNETID of the ethernet device port used for
initial connecting, and derive the IB device port used for SMC RDMA
traffic.
On platforms without PNETID support fall back to the existing
solution of a configured pnet table.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SMC it is important to know the current port state of RoCE devices.
Monitoring port states has been triggered, when a RoCE device was added
to the pnet table. To support future alternatives to the pnet table the
monitoring of ports is made independent of the existence of a pnet table.
It starts once the smc_ib_device is established.
Due to this change smc_ib_remember_port_attr() is now a local function
and shuffling its location and the location of its used functions
makes any forward references obsolete.
And the duplicate SMC_MAX_PORTS definition is removed.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
Fixes for running mirror-to-gretap tests on veth
The forwarding selftests infrastructure makes it possible to run the
individual tests on a purely software netdevices. Names of interfaces to
run the test with can be passed as command line arguments to a test.
lib.sh then creates veth pairs backing the interfaces if none exist in
the system.
However, the tests need to recognize that they might be run on a soft
device. Many mirror-to-gretap tests are buggy in this regard. This patch
set aims to fix the problems in running mirror-to-gretap tests on veth
devices.
In patch #1, a service function is split out of setup_wait().
In patch #2, installing a trap is made optional.
In patch #3, tc filters in several tests are tweaked to work with veth.
In patch #4, the logic for waiting for neighbor is fixed for veth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running the test on soft devices, there's no mechanism to
gratuitously start resolving the neighbor for remote tunnel endpoint.
So instead of passively waiting, wait for the device to be up, and then
probe the neighbor with a ping.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running mirror_gre_bridge_1d_vlan tests on veth, several issues
cause spurious failures:
- vlan_ethtype should be ip, not ipv6 even in mirror-to-ip6gretap case,
because the overlay packet is still IPv4.
- Similarly ip_proto matches the innermost IP protocol, so can't be used
to filter out GRE packet. Drop the corresponding condition.
- Because the above fixes the filters to match in slow path as well,
they need to be made skip_hw so as not to double-count packets.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several cases where traffic that would normally be forwarded
in silicon needs to be observed in slow path. That's achieved by
trapping such traffic, and the functions trap_install() and
trap_uninstall() realize that. However, such treatment is obviously
wrong if the device in question is actually a soft device not backed by
an ASIC.
Therefore try to trap if possible, but fall back to inserting a continue
if not.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split out of setup_wait() a function setup_wait_dev() that waits for a
single device. This gives tests the opportunity to wait for a selected
device after they tinkered with its upness.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_skb_with_frags uses __GFP_NORETRY for non-sleeping allocations
which is just a noop and a little bit confusing.
__GFP_NORETRY was added by ed98df3361f0 ("net: use __GFP_NORETRY for
high order allocations") to prevent from the OOM killer. Yet this was
not enough because fb05e7a89f50 ("net: don't wait for order-3 page
allocation") didn't want an excessive reclaim for non-costly orders
so it made it completely NOWAIT while it preserved __GFP_NORETRY in
place which is now redundant.
Drop the pointless __GFP_NORETRY because this function is used as
copy&paste source for other places.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
