| Age | Commit message (Collapse) | Author |
|---|
|
On Intel Broxton the GPIO hardware consists of several chips that all share
the parent interrupt. It is not possible to handle this by setting chained
handler for each chip (as they will overwrite each other).
To overcome this we need to request the interrupt using devm_request_irq()
and pass IRQF_SHARED with the flags.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Returning an error instead of NULL in bgpio_map if
platform_get_resource_byname does not find a resource was introduced with
commit cf3f2a2c8bae ("gpio: generic: improve error handling in bgpio_map").
This results in several qemu runtime failures with default and non-default
configurations, if attempts are made to boot from mmcblk0. Examples for
failures with multi_v7_defconfig are
Machine: vexpress-a9 dtb: vexpress-v2p-ca9
Machine: vexpress-a15 dtb: vexpress-v2p-ca15-tc1
Crash:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Looking into the code, always returning an error if bgpio_map fails
does not appear to make much sense, since the code in bgpio_setup_io
specifically supports some of the resources to be NULL.
Fixes: cf3f2a2c8bae ("gpio: generic: improve error handling in bgpio_map")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Put in a compliance checklist.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 677b2ff4afd9996eabefc9472c701211b4b49e87.
|
|
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
Fixes: 6e9088920258 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This new compatible string, "brcm,iproc-gpio", should be used for
all new iproc-based future SoCs.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove gpio to pinctrl pin mapping code from driver and
address this through standard property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If GPIO controller's pins are muxed, pin-controller subsystem
need to be intimated by defining mapping between gpio and
pinmux controller. This patch adds required properties to
define this mapping via DT.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
add HS400 mode and tune support
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
add implement of ops->hw_reset() for eMMC
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add 400Mhz clock source for HS400 mode
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While unifying how blkcg stats are collected, 77ea733884eb ("blkcg:
move io_service_bytes and io_serviced stats into blkcg_gq")
incorrectly used bio->flags instead of bio->rw to tell the IO type.
This made IOs to be accounted as the wrong type. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 77ea733884eb ("blkcg: move io_service_bytes and io_serviced stats into blkcg_gq")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Request_module gets really unhappy when called from async probing, so
revert to not auto load device handler modules during the SCSI bus
scan. While autoloading would be really useful we never did this
until 4.3-rc and it turns out that functionality doesn't actually
work.
Fixes: 566079 ("dm-mpath, scsi_dh: request scsi_dh modules in scsi_dh, not dm-mpath")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Julia Lawall says:
====================
add missing of_node_put
The various for_each device_node iterators performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
The complete semantic patch that fixes this problem is
(http://coccinelle.lip6.fr):
// <smpl>
@r@
local idexpression n;
expression e1,e2;
iterator name for_each_node_by_name, for_each_node_by_type,
for_each_compatible_node, for_each_matching_node,
for_each_matching_node_and_match, for_each_child_of_node,
for_each_available_child_of_node, for_each_node_with_property;
iterator i;
statement S;
expression list [n1] es;
@@
(
(
for_each_node_by_name(n,e1) S
|
for_each_node_by_type(n,e1) S
|
for_each_compatible_node(n,e1,e2) S
|
for_each_matching_node(n,e1) S
|
for_each_matching_node_and_match(n,e1,e2) S
|
for_each_child_of_node(e1,n) S
|
for_each_available_child_of_node(e1,n) S
|
for_each_node_with_property(n,e1) S
)
&
i(es,n,...) S
)
@@
local idexpression r.n;
iterator r.i;
expression e;
expression list [r.n1] es;
@@
i(es,n,...) {
...
(
of_node_put(n);
|
e = n
|
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
@@
local idexpression r.n;
iterator r.i;
expression e;
expression list [r.n1] es;
@@
i(es,n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
@@
local idexpression r.n;
iterator r.i;
expression e;
identifier l;
expression list [r.n1] es;
@@
i(es,n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? goto l;
)
...
}
...
l: ... when != n// </smpl>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n,...) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_available_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gre_gso_segment() chokes if SIT frames were aggregated by GRO engine.
Fixes: 61c1db7fae21e ("ipv6: sit: add GSO/TSO support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 1bab0de0274f ("dm-mpath, scsi_dh: don't let dm detach device
handlers") removed reference counting of attached scsi device handler.
As a result, handler data is freed immediately via scsi_dh->detach()
in the context of scsi_remove_device() where activation request can be
still in flight.
This patch moves scsi_dh_handler_detach() to sdev releasing function,
scsi_device_dev_release_usercontext(), at that point the device
is already in quiesced state.
Fixes: 1bab0de0274f ("dm-mpath, scsi_dh: don't let dm detach device handlers")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.
Just return from mvs_slot_task_free when passed with NULL slot.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Sergei Shtylyov says:
====================
sh_eth: RX buffer alignment fixes
Here's a set of 2 patches against DaveM's 'net.git' repo which are the
fixes to the RX buffer size calculation.
[1/2] sh_eth: fix RX buffer size alignment
[2/2] sh_eth: fix RX buffer size calculation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
We should not trace digicolor_timer_sched_read() function. Fix this by adding
the notrace attribute to this function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
We should not trace the ftm_read_sched_clock() function.
Fix this by adding the notrace attribute to this function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
We should not trace the pit_read_sched_clock() function. Fix this by adding a
notrace attribute to this function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently prima2 timer can be used as a scheduler clock. We properly
marked sirfsoc_read_sched_clock() as notrace but we then call another
function sirfsoc_timer_read() that _wasn't_ notrace.
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
Fix this by adding notrace attribute to the sirfsoc_timer_read() function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently samsung_pwm_timer can be used as a scheduler clock. We properly
marked samsung_read_sched_clock() as notrace but we then call another
function samsung_clocksource_read() that _wasn't_ notrace.
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
Fix this by adding notrace attribute to the samsung_clocksource_read()
function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently pistachio can be used as a scheduler clock. We properly marked
pistachio_read_sched_clock() as notrace but we then call another function
pistachio_clocksource_read_cycles() that _wasn't_ notrace.
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
Fix this by adding notrace attribute to the pistachio_clocksource_read_cycles()
function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently arm_global_timer can be used as a scheduler clock. We properly
marked gt_sched_clock_read() as notrace but we then call another function
gt_counter_read() that _wasn't_ notrace.
Having a traceable function in the sched_clock() path leads to a recursion
within ftrace and a kernel crash.
Fix this by adding an extra notrace function to keep other users of
gt_counter_read() traceable.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
button bits
commit 92bac83dd79e ("Input: alps - non interleaved V2 dualpoint has
separate stick button bits") assumes that all alps v2 non-interleaved
dual point setups have the separate stick button bits.
Later we limited this to Dell laptops only because of reports that this
broke things on non Dell laptops. Now it turns out that this breaks things
on the Dell Latitude D600 too. So it seems that only the Dell Latitude
D420/430/620/630, which all share the same touchpad / stick combo,
have these separate bits.
This patch limits the checking of the separate bits to only these models
fixing regressions with other models.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 4857c91f0d19 changed the way how irq affinity is setup in
setup_ioapic_dest() from using the core helper function to
unconditionally calling the irq_set_affinity() callback of the
underlying irq chip.
That results in a NULL pointer dereference for the rare case where the
underlying irq chip is lapic_chip which has no irq_set_affinity()
callback. lapic_chip is occasionally used for the timer interrupt (irq
0).
The fix is simple: Check the availability of the callback instead of
calling it unconditionally.
Fixes: 4857c91f0d19 "x86/ioapic: Force affinity setting in setup_ioapic_dest()"
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two late fixes for the AMD IOMMU driver:
- add an additional check to the io page-fault handler to avoid a
BUG_ON being hit in handle_mm_fault()
- fix a problem with devices writing to the system management area
and were blocked by the IOMMU because the driver wrongly cleared
out the DTE flags allowing that access"
* tag 'iommu-fixes-v4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Don't clear DTE flags when modifying it
iommu/amd: Fix BUG when faulting a PROT_NONE VMA
|
|
Pull md fixes from Neil Brown:
"Some raid1/raid10 fixes.
I meant to get this to you before -rc7, but what with all the travel
plans..
Two fixes for bugs that are in both raid1 and raid10. Both related to
bad-block-lists and at least one needs to be back ported to 3.1.
Also a revision for the "new" layout in raid10. This "new" code
(which aims to improve robustness) actually reduces robustness in some
cases. It probably isn't in use at all as not public user-space code
makes use of these new layouts. However just in case someone has
their own code, it would be good to get the WARNing out for them
sooner"
* tag 'md/4.3-rc6-fixes' of git://neil.brown.name/md:
md/raid10: fix the 'new' raid10 layout to work correctly.
md/raid10: don't clear bitmap bit when bad-block-list write fails.
md/raid1: don't clear bitmap bit when bad-block-list write fails.
md/raid10: submit_bio_wait() returns 0 on success
md/raid1: submit_bio_wait() returns 0 on success
|
|
Pull drm fixes from Dave Airlie:
"Last fixes from me: one amdgpu/radeon suspend resume and one leak fix,
along with one vmware fix for some issues when command submission
fails"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: don't try to recreate sysfs entries on resume
drm/radeon: don't try to recreate sysfs entries on resume
drm/amdgpu: stop leaking page flip fence
drm/vmwgfx: Stabilize the command buffer submission code
|
|
Currently memremap checks if the range is "System RAM" and returns the
kernel linear address. This is broken for highmem platforms where a
range may be "System RAM", but is not part of the kernel linear mapping.
Fallback to ioremap_cache() in these cases, to let the arch code attempt
to handle it.
Note that ARM ioremap will WARN when attempting to remap ram, and in
that case the caller needs to be fixed. For this reason, existing
ioremap_cache() usages for ARM are already trained to avoid attempts to
remap ram.
The impact of this bug is low for now since the pmem driver is the only
user of memremap(), but this is important to fix before more conversions
to memremap arrive in 4.4.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
It's annoying to see error or help message when command has many options
like in perf record, report or top. So setup pager when print parser
error or help message - it should be OK since no UI is enabled at the
parsing time. The usage_with_options() already disables it by calling
exit_browser() anyway.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445701767-12731-3-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
So that it can be more consistent with other --show-* options. The old
name (--showcpuutilization) is provided only for compatibility.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445701767-12731-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently if an option name is ambiguous it only prints first two
matched option names but no help. It'd be better it could show all
possible names and help messages too.
Before:
$ perf report --show
Error: Ambiguous option: show (could be --show-total-period or
--show-ref-call-graph)
Usage: perf report [<options>]
After:
$ perf report --show
Error: Ambiguous option: show (could be --show-total-period or
--show-ref-call-graph)
Usage: perf report [<options>]
-n, --show-nr-samples
Show a column with the number of samples
--showcpuutilization
Show sample percentage for different cpu modes
-I, --show-info Display extended information about perf.data file
--show-total-period
Show a column with the sum of periods
--show-ref-call-graph
Show callgraph from reference event
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445701767-12731-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
