| Age | Commit message (Collapse) | Author |
|---|
|
We face some regressions on a few IXP42x systems when
accessing flash, the following unrelated error prints
appear from the PCI driver:
ixp4xx-pci c0000000.pci: PCI: abort_handler addr = 0xff9ffb5f,
isr = 0x0, status = 0x22a0
ixp4xx-pci c0000000.pci: imprecise abort
(...)
It turns out that while bit 7 is masked "reserved" it is
not unused, so masking it off as zero is dangerous, and
breaks flash access on some systems such as the NSLU2.
Be more careful and avoid masking off any of the reserved
bits 7, 8, 9 or 30. Only keep masking EXP_WORD (bit 2)
on IXP43x which is necessary in some setups.
Fixes: 1c953bda90ca ("bus: ixp4xx: Add a driver for IXP4xx expansion bus")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221122134411.2030372-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
After commit cbfecb927f42 ("fs: record I_DIRTY_TIME even if inode
already has I_DIRTY_INODE") writeback_single_inode can push inode with
I_DIRTY_TIME set to b_dirty_time list. In case of freeing inode with
I_DIRTY_TIME set this can happen after deletion of inode from i_io_list
at evict. Stack trace is following.
evict
fat_evict_inode
fat_truncate_blocks
fat_flush_inodes
writeback_inode
sync_inode_metadata(inode, sync=0)
writeback_single_inode(inode, wbc) <- wbc->sync_mode == WB_SYNC_NONE
This will lead to use after free in flusher thread.
Similar issue can be triggered if writeback_single_inode in the
stack trace update inode->i_io_list. Add explicit check to avoid it.
Fixes: cbfecb927f42 ("fs: record I_DIRTY_TIME even if inode already has I_DIRTY_INODE")
Reported-by: syzbot+6ba92bd00d5093f7e371@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Svyatoslav Feldsherov <feldsherov@google.com>
Link: https://lore.kernel.org/r/20221115202001.324188-1-feldsherov@google.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
nf_flow_table_block_setup and the driver TC_SETUP_FT call can modify the flow
block cb list while they are being traversed elsewhere, causing a crash.
Add a write lock around the calls to protect readers
Fixes: c29f74e0df7a ("netfilter: nf_flow_table: hardware offload support")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The commit 510841da1fcc ("netfilter: ipset: enforce documented limit to
prevent allocating huge memory") was too strict and prevented to add up to
64 clashing elements to a hash:net,iface type of set. This patch fixes the
issue and now the type behaves as documented.
Fixes: 510841da1fcc ("netfilter: ipset: enforce documented limit to prevent allocating huge memory")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a new amd pstate driver command line option to enable driver passive
working mode via MSR and shared memory interface to request desired
performance within abstract scale and the power management firmware
(SMU) convert the perf requests into actual hardware pstates.
Also the `disable` parameter can disable the pstate driver loading by
adding `amd_pstate=disable` to kernel command line.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce the `amd_pstate` driver new working mode with
`amd_pstate=passive` added to kernel command line.
If there is no passive mode enabled by user, amd_pstate driver will be
disabled by default for now.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the amd_pstate driver is built-in users still need a method to be
able enable or disable it depending upon their circumstance.
Add support for an early parameter to do this.
There is some performance degradation on a number of ASICs in the
passive mode. This performance issue was originally discovered in
shared memory systems but it has been proven that certain workloads
on MSR systems also suffer performance issues.
Set the amd-pstate driver as disabled by default to temporarily
mitigate the performance problem.
1) with `amd_pstate=disable`, pstate driver will be disabled to load at
kernel booting.
2) with `amd_pstate=passive`, pstate driver will be enabled and loaded
as non-autonomous working mode supported in the low-level power
management firmware.
3) If neither parameter is specified, the driver will be disabled by
default to avoid triggering performance regressions in certain ASICs
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently when the amd-pstate and acpi_cpufreq are both built into
kernel as module driver, amd-pstate will not be loaded by default
in this case.
Change amd-pstate driver as built-in type, it will resolve the loading
sequence problem to allow user to make amd-pstate driver as the default
cpufreq scaling driver.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Fixes: ec437d71db77 ("cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
init
MSR_AMD_PERF_CTL is guaranteed to be 0 on a cold boot. However, on a
kexec boot, for instance, it may have a non-zero value (if the cpu was
in a non-P0 Pstate). In such cases, the cores with non-P0 Pstates at
boot will never be pushed to P0, let alone boost frequencies.
Kexec is a common workflow for reboot on Linux and this creates a
regression in performance. Fix it by explicitly setting the
MSR_AMD_PERF_CTL to 0 during amd_pstate driver init.
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit 6d5afdc97ea71958287364a1f1d07e59ef151b11.
On a Pixel 6 device, it is observed that this commit increases
latency by approximately 50ms, or 20%, in migrating a task
that requires full CPU utilization from a LITTLE CPU to Fmax
on a big CPU. Reverting this change restores the latency back
to its original baseline value.
Fixes: 6d5afdc97ea7 ("cpufreq: schedutil: Move max CPU capacity to sugov_policy")
Signed-off-by: Sam Wu <wusamuel@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The blamed commit introduced the following smatch warning in the
function lan9662_otp_wait_flag_clear:
drivers/nvmem/lan9662-otpc.c:43 lan9662_otp_wait_flag_clear() warn: signedness bug returning '(-110)'
Fix this by changing the return type of the function
lan9662_otp_wait_flag_clear() to be int instead of bool.
Fixes: 9e8f208ad5229d ("nvmem: lan9662-otp: add support")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221118063840.6357-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error, the function memremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: 5a3fa75a4d9c ("nvmem: Add driver to expose reserved memory as nvmem")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221118063840.6357-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fix for v6.1-rc
This contains a tiny fix to align the driver compatible string in the
binding documentation with the one used in DTS.
- dt-bindings: interconnect: qcom,msm8998-bwmon: Correct SC7280 CPU compatible
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
dt-bindings: interconnect: qcom,msm8998-bwmon: Correct SC7280 CPU compatible
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
"3rd set of IIO fixes for the 6.1 cycle.
Usual mixed bunch of driver fixes.
* sw-triggers
- Fix failure to cleanup up list registration in an error path.
* aspeed,adc
- Drop the trim valid dts property as it doesn't account for unprogrammed
OTP and that can be easily detected without it.
* avago,apds9960:
- Fix register address for gesture gain.
* bosch,bma400
- Fix a memory leak in an error path.
* rohm,rpr0521
- Fix missing dependency on IIO_BUFFER/IIO_TRIGGERED_BUFFER.
* ti,afe4403/4404
- Fix out of band read by moving reads down to where they are
used."
* tag 'iio-fixes-for-6.1c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
dt-bindings: iio: adc: Remove the property "aspeed,trim-data-valid"
iio: adc: aspeed: Remove the trim valid dts property.
iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
iio: accel: bma400: Fix memory leak in bma400_get_steps_reg()
iio: light: rpr0521: add missing Kconfig dependencies
iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
iio: health: afe4403: Fix oob read in afe4403_read_raw
iio: light: apds9960: fix wrong register for gesture gain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into work-linus
Xu writes:
FPGA Manager changes for 6.1-final
Intel m10 bmc secure update
- Russ's change fixes Kconfig dependencies
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-6.1 branch)
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: m10bmc-sec: Fix kconfig dependencies
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20221118224540.619276-573-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-574-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-575-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-576-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-577-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-578-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-579-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221118224540.619276-580-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-581-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-582-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221118224540.619276-583-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-584-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-585-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
gether_disconnect+0x2c/0x1f8
rndis_disable+0x4c/0x74
composite_disconnect+0x74/0xb0
configfs_composite_disconnect+0x60/0x7c
usb_gadget_disconnect+0x70/0x124
usb_gadget_unregister_driver+0xc8/0x1d8
gadget_dev_desc_UDC_store+0xec/0x1e4
(2) rm /config/usb_gadget/g1/configs/b.1/f1
rndis_deregister+0x28/0x54
rndis_free+0x44/0x7c
usb_put_function+0x14/0x1c
config_usb_cfg_unlink+0xc4/0xe0
configfs_unlink+0x124/0x1c8
vfs_unlink+0x114/0x1dc
(3) rmdir /config/usb_gadget/g1/functions/rndis.gs4
panic+0x1fc/0x3d0
do_page_fault+0xa8/0x46c
do_mem_abort+0x3c/0xac
el1_sync_handler+0x40/0x78
0xffffff801138f880
rndis_close+0x28/0x34
eth_stop+0x74/0x110
dev_close_many+0x48/0x194
rollback_registered_many+0x118/0x814
unregister_netdev+0x20/0x30
gether_cleanup+0x1c/0x38
rndis_attr_release+0xc/0x14
kref_put+0x74/0xb8
configfs_rmdir+0x314/0x374
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
=======================================================================
Fixes: 0a55187a1ec8 ("USB: gadget core: Issue ->disconnect() callback from usb_gadget_disconnect()")
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: TaoXue <xuetao09@huawei.com>
Link: https://lore.kernel.org/r/20221121130805.10735-1-water.zhangjiantao@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently this driver triggers extcon and typec state update in its
probe function, to read out current state reported by the chip and
report the correct state to upper layers. This synchronization is
performed correctly, but only in case the chip indicates a pending
interrupt in reg09 register.
This fails to cover the situation where all interrupts reported by
the chip were already handled by Linux before reboot, then the system
rebooted, and then Linux starts again. In this case, the TUSB320 no
longer reports any interrupts in reg09, and the state update does not
perform any update as it depends on that interrupt indication.
Fix this by turning tusb320_irq_handler() into a thin wrapper around
tusb320_state_update_handler(), where the later now contains the bulk
of the code of tusb320_irq_handler(), but adds new function parameter
"force_update". The "force_update" parameter can be used by the probe
function to assure that the state synchronization is always performed,
independent of the interrupt indicated in reg09. The interrupt handler
tusb320_irq_handler() callback uses force_update=false to avoid state
updates on potential spurious interrupts and retain current behavior.
Fixes: 06bc4ca115cdd ("extcon: Add driver for TI TUSB320")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221120141509.81012-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A request to Manish Narani (see Link) asked for clarification of the
reference to the config ARCH_VERSAL in the support of Xilinx SoCs with
DesignWare Core USB3 IP.
As there is no response, clean up the reference to the non-existing config
symbol. While at it, follow up on Felipe Balbi's request to add the
alternative COMPILE_TEST dependency.
Link: https://lore.kernel.org/all/CAKXUXMwgWfX8+OvY0aCwRNukencwJERAZzU7p4eOLXQ2zv6rAg@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221116110444.8340-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Probe for omap2430 glue layer is now broken for interrupt resources in
all cases.
Commit 239071064732 ("partially Revert "usb: musb: Set the DT node on the
child device"") broke probing for SoCs using ti-sysc interconnect target
module as the dt node is not found.
Commit a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from
DT core") caused omap3 to fail with error "-ENXIO: IRQ mc not found" as
the IRQ resources are no longer automatically populated from devicetree.
Let's fix the issues by calling device_set_of_node_from_dev() only if the
SoC has been updated to probe with ti-sysc. And for legacy SoCs, let's
populate the resources manually as needed.
Note that once we have updated the SoCs to probe with proper devicetree
data in all cases, this is no longer needed. But doing that requires
patching both devicetree and SoC code, so let's fix the probe issues first.
Fixes: a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT core")
Fixes: 239071064732 ("partially Revert "usb: musb: Set the DT node on the child device"")
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Reported-by: Sicelo Mhlongo <absicsz@gmail.com>
Tested-by: Sicelo Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221118102532.34458-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While the code currently correctly calls tps6598x_disconnect before jumping
to the error cleanup label it's inconsistent compared to all the other cleanup
actions and prone to introduce bugs if any more resources are added.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-4-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
typec_unregister_port is only called for some error paths after
typec_register_port was successful. Ensure it's called in all
cases.
Fixes: 92440202a880 ("usb: typec: tipd: Only update power status on IRQ")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-3-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The err_role_put error path always calls fwnode_handle_put to release
the fwnode. This path can be reached after probe itself has already
released that fwnode though. Fix that by moving fwnode_handle_put in the
happy path to the very end.
Fixes: 18a6c866bb19 ("usb: typec: tps6598x: Add USB role switching logic")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-2-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can't just return if devm_tps6598_psy_register fails since previous
resources are not devres managed and have yet to be cleaned up.
Fixes: 10eb0b6ac63a ("usb: typec: tps6598x: Export some power supply properties")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is error log when add a usb3 root hub without ports:
"hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)"
so omit the shared hcd if either of the root hubs has no ports, but
usually there is no usb3 port.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221118110116.20165-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I got the following report while doing device(mt6370-tcpc) load
test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@34/tcpc/connector
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 5e85a04c8c0d ("usb: typec: add fwnode to tcpc")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document the SM8550 dwc3 compatible.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221116150600.3011160-1-abel.vesa@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
typec_altmode_exit checks if ops->enter is not NULL but then calls
ops->exit a few lines below. Fix that and check for the function
pointer it's about to call instead.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114165924.33487-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable l is just being accumulated and it's never used
anywhere else. The variable and the addition are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221111165724.557152-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit fff61d4ccf3d ("dt-bindings: usb: usb251xb: Convert to YAML schema")
converts usb251xb.txt to usb251xb.yaml, but misses to adjust its reference
in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Repair this file reference in MICROCHIP USB251XB DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115103153.28502-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to use an intermediate array for these memory allocations,
so, axe it.
While at it, turn a '== NULL' into a shorter '!' when testing memory
allocation failure.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/deab9696fc4000499470e7ccbca7c36fca17bd4e.1668458274.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The platform_get_irq() is necessary to use to get dynamic
IRQ resolution when instantiating the device from the
device tree. IRQs are not passed as resources in that
case.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-4-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds optional handling of the peripheral clock PCLK.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-3-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for an optional external PHY to the FOTG210
UDC driver.
Tested with the GPIO VBUS PHY driver on the Gemini SoC.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a local struct device *dev pointer and use dev_err()
etc to report status.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Faraday Technology FOTG210 USB2 Dual Role Controller is only present
on Cortina Systems Gemini SoCs. Hence add a dependency on ARCH_GEMINI,
to prevent asking the user about its drivers when configuring a kernel
without Cortina Systems Gemini SoC support.
Fixes: 1dd33a9f1b95ab59 ("usb: fotg210: Collect pieces of dual mode controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/a989b3b798ecaf3b45f35160e30e605636d66a77.1669044086.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel robot reports a link failure when activating the
FOTG210 host subdriver with =y on a system where the USB host
core is a module (CONFIG_USB=m).
This is a bit of special case, so mimic the Kconfig incantations
from DWC3: let the subdrivers for host or peripheral depend
on the host or gadget support being =y or the same as the
FOTG210 core itself.
This should ensure that either:
- The host (CONFIG_USB) or gadget (CONFIG_GADGET) is compiled
in and then the FOTG210 can be either module or compiled
in.
- The host or gadget is modular, and then the FOTG210 module
must be a module too, or we cannot resolve the symbols
at link time.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-usb/202211112132.0BUPGKCd-lkp@intel.com/
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221111144821.113665-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch modifies the TD_SIZE in TRB before ZLP TRB.
The TD_SIZE in TRB before ZLP TRB must be set to 1 to force
processing ZLP TRB by controller.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115092218.421267-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
