| Age | Commit message (Collapse) | Author |
|---|
|
Convert Spitz to use software nodes for specifying GPIOs for the audio
chip.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240628180852.1738922-7-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert the Spitz to use software nodes for specifying SPI CS. Because
the SPI core can figure out the number of chipselects from the number
of GPIO handles specified in properties, setting "num-cs" property is
no longer needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240628180852.1738922-6-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
platform_device_register_full() to instantiate SPI controller in one go
instead of allocating it, creating a software node, and registering the
platform device as separate steps.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240628180852.1738922-5-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Switch vbus gpios from using a custom GPIO lookup table to software
properties using PROPERTY_ENTRY_GPIO() constructs which closely mimic
device tree gpio properties.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240628180852.1738922-4-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The platform data for the GPIO controllers for the boards using non-DT
setup is the same between PXA25x (gumstix) and PXA27x (Spitz) devices.
Move it into devices.c to consolidate code. It will help with conversion
to software nodes/properties.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240628180852.1738922-3-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
GPIOs controlling backlight on Spitz and Akita are coming from GPIO
expanders, not the pxa27xx-gpio block, correct it.
Additionally GPIO lookup tables operate with pin numbers rather than
legacy GPIO numbers, fix that as well. Use raw numbers instead of legacy
GPIO names to avoid confusion.
Fixes: ee0c8e494cc3 ("backlight: corgi: Convert to use GPIO descriptors")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20240628180852.1738922-2-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/arm
ARM: tegra: Core changes for v6.11-rc1
Uses software nodes to describe rfkill instead of using a GPIO lookup
table.
* tag 'tegra-for-6.11-arm-core' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: paz00: Use software nodes to describe GPIOs for WiFi rfkill
Link: https://lore.kernel.org/r/20240628210818.3627404-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add depend on WATCHDOG, otherwise modpost fails with
ERROR: modpost: "watchdog_init_timeout" [drivers/platform/cznic/turris-omnia-mcu.ko] undefined!
ERROR: modpost: "devm_watchdog_register_device" [drivers/platform/cznic/turris-omnia-mcu.ko] undefined!
Fixes: ab89fb5fb92c ("platform: cznic: turris-omnia-mcu: Add support for MCU watchdog")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407040711.g19y3cWq-lkp@intel.com/
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240708114002.4285-3-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add depend on OF, otherwise the compilation fails with
error: no member named 'of_gpio_n_cells' in 'struct gpio_chip'
error: no member named 'of_xlate' in 'struct gpio_chip'
Fixes: dfa556e45ae9 ("platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407031646.trNSwajF-lkp@intel.com/
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240708114002.4285-2-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When SMP is enabled and spinlocks are actually functional then there is
a deadlock with the 'statelock' spinlock between ks8851_start_xmit_spi
and ks8851_irq:
watchdog: BUG: soft lockup - CPU#0 stuck for 27s!
call trace:
queued_spin_lock_slowpath+0x100/0x284
do_raw_spin_lock+0x34/0x44
ks8851_start_xmit_spi+0x30/0xb8
ks8851_start_xmit+0x14/0x20
netdev_start_xmit+0x40/0x6c
dev_hard_start_xmit+0x6c/0xbc
sch_direct_xmit+0xa4/0x22c
__qdisc_run+0x138/0x3fc
qdisc_run+0x24/0x3c
net_tx_action+0xf8/0x130
handle_softirqs+0x1ac/0x1f0
__do_softirq+0x14/0x20
____do_softirq+0x10/0x1c
call_on_irq_stack+0x3c/0x58
do_softirq_own_stack+0x1c/0x28
__irq_exit_rcu+0x54/0x9c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x50
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x64/0x68
__netif_schedule+0x6c/0x80
netif_tx_wake_queue+0x38/0x48
ks8851_irq+0xb8/0x2c8
irq_thread_fn+0x2c/0x74
irq_thread+0x10c/0x1b0
kthread+0xc8/0xd8
ret_from_fork+0x10/0x20
This issue has not been identified earlier because tests were done on
a device with SMP disabled and so spinlocks were actually NOPs.
Now use spin_(un)lock_bh for TX queue related locking to avoid execution
of softirq work synchronously that would lead to a deadlock.
Fixes: 3dc5d4454545 ("net: ks8851: Fix TX stall caused by TX buffer overrun")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <horms@kernel.org>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240706101337.854474-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert the Atmel GPIO controller binding document to DT schema format
using json-schema.
The at91 pinctrl driver uses "atmel,at91rm9200-gpio" compatible string
to find the number of active GPIO banks and identify the pinmux nodes.
"atmel,at91sam9x5-gpio" and "microchip,sam9x60-gpio" have additional
registers to handle drive-strength, slew-rate, pull-down to drive the
pinmux configs.
The new compatible string "microchip,sam9x7-gpio" is added.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240709092354.191643-5-manikandan.m@microchip.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Merge the pmdomain fixes for v6.10-rc[n] into the next branch, to allow them
to get tested together with the new changes that are targeted for v6.11.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
'struct meson_secure_pwrc_domain_desc' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4909 4072 0 8981 2315 drivers/pmdomain/amlogic/meson-secure-pwrc.o
After:
=====
text data bss dec hex filename
8605 392 0 8997 2325 drivers/pmdomain/amlogic/meson-secure-pwrc.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/871d6b708de8bb42e1fabd8a601dc9a9a217cf00.1719863475.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The Venus driver requires vcodec GDSC to be ON in SW mode for clock
operations and move it back to HW mode to gain power benefits. Earlier,
as there is no interface to switch the GDSC mode from GenPD framework,
the GDSC is moved to HW control mode as part of GDSC enable callback and
venus driver is writing to its POWER_CONTROL register to keep the GDSC ON
from SW whereever required. But the POWER_CONTROL register addresses
are not constant and can vary across the variants.
Also as per the HW recommendation, the GDSC mode switching needs to be
controlled from respective GDSC register and this is a uniform approach
across all the targets. Hence use dev_pm_genpd_set_hwmode() API which
controls GDSC mode switching using its respective GDSC register.
In venus V6 variants, the vcodec gdsc gets enabled in SW mode by default
with new HW_CTRL_TRIGGER flag and there is no need to switch it to SW
mode again after enable, hence add check to avoid switching gdsc to SW mode
again after gdsc enable. Similarly add check to avoid switching GDSC to HW
mode before disabling the GDSC, so GDSC gets enabled in SW mode in the next
enable.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240624044809.17751-6-quic_jkona@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For Venus V6 variant SoCs(sm8250, sc7280), the venus driver uses the newly
introduced dev_pm_genpd_set_hwmode() API to switch the vcodec GDSC to
HW/SW control modes at runtime. Hence use HW_CTRL_TRIGGER flag for vcodec
GDSC's on sm8250, sc7280 to register the set_hwmode_dev & get_hwmode_dev
callbacks for vcodec GDSC and allow the GDSC mode to be changed using
dev_pm_genpd_set_hwmode() API.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240624044809.17751-5-quic_jkona@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some GDSC client drivers require the GDSC mode to be switched dynamically
to HW mode at runtime to gain the power benefits. Typically such client
drivers require the GDSC to be brought up in SW mode initially to enable
the required dependent clocks and configure the hardware to proper state.
Once initial hardware set up is done, they switch the GDSC to HW mode to
save power. At the end of usecase, they switch the GDSC back to SW mode
and disable the GDSC.
Introduce HW_CTRL_TRIGGER flag to register the set_hwmode_dev and
get_hwmode_dev callbacks for GDSC's whose respective client drivers
require the GDSC mode to be switched dynamically at runtime using
dev_pm_genpd_set_hwmode() API.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240624044809.17751-4-quic_jkona@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Now that genpd supports dynamically switching the control for an
attached device between hardware- and software-mode, let's add this
information to the genpd summary under managed by column in debugfs.
Suggested-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240624044809.17751-3-quic_jkona@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some power-domains may be capable of relying on the HW to control the power
for a device that's hooked up to it. Typically, for these kinds of
configurations the consumer driver should be able to change the behavior of
power domain at runtime, control the power domain in SW mode for certain
configurations and handover the control to HW mode for other usecases.
To allow a consumer driver to change the behaviour of the PM domain for its
device, let's provide a new function, dev_pm_genpd_set_hwmode(). Moreover,
let's add a corresponding optional genpd callback, ->set_hwmode_dev(),
which the genpd provider should implement if it can support switching
between HW controlled mode and SW controlled mode. Similarly, add the
dev_pm_genpd_get_hwmode() to allow consumers to read the current mode and
its corresponding optional genpd callback, ->get_hwmode_dev(), which the
genpd provider can also implement to synchronize the initial HW mode
state in genpd_add_device() by reading back the mode from the hardware.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240624044809.17751-2-quic_jkona@quicinc.com
|
|
Add support for the A5 power controller, whose registers are
in the secure domain and should be accessed via SMC.
Signed-off-by: Hongyu Chen <hongyu.chen1@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240627-a5_secpower-v1-2-1f47dde1270c@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Merge the immutable branch dt into next, to allow the DT bindings to be
tested together with changes that are targeted for v6.11.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add devicetree binding document and related header file for
Amlogic A5 secure power domains.
Signed-off-by: Hongyu Chen <hongyu.chen1@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240627-a5_secpower-v1-1-1f47dde1270c@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
rvu_check_rsrc_availability()
In rvu_check_rsrc_availability() in case of invalid SSOW req, an incorrect
data is printed to error log. 'req->sso' value is printed instead of
'req->ssow'. Looks like "copy-paste" mistake.
Fix this mistake by replacing 'req->sso' with 'req->ssow'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 746ea74241fa ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240705095317.12640-1-amishin@t-argos.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the cases where the power domain connected to logics is allowed to
transition from a level(L)-->power collapse(0)-->retention(1) or
vice versa retention(1)-->power collapse(0)-->level(L) will cause the
logic to lose the configurations. The ARC does not support retention
to collapse transition on MxC rails.
The targets from SM8450 onwards the PLL logics of clock controllers are
connected to MxC rails and the recommended configurations are carried
out during the clock controller probes. The MxC transition as mentioned
above should be skipped to ensure the PLL settings are intact across
clock controller power on & off.
On older targets that do not split MX into MxA and MxC does not collapse
the logic and it is parked always at RETENTION, thus this issue is never
observed on those targets.
Cc: stable@vger.kernel.org # v5.17
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240625-avoid_mxc_retention-v2-1-af9c2f549a5f@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
HP 250 G7 has a mute LED that can be made to work using quirk
ALC269_FIXUP_HP_LINE1_MIC1_LED. Enable already existing quirk.
Signed-off-by: Nazar Bilinskyi <nbilinskyi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240709080546.18344-1-nbilinskyi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
bnxt doesn't check if a ring is used by RSS contexts when reducing
ring count. Core performs a similar check for the drivers for
the main context, but core doesn't know about additional contexts,
so it can't validate them. bnxt_fill_hw_rss_tbl_p5() uses ring
id to index bp->rx_ring[], which without the check may end up
being out of bounds.
BUG: KASAN: slab-out-of-bounds in __bnxt_hwrm_vnic_set_rss+0xb79/0xe40
Read of size 2 at addr ffff8881c5809618 by task ethtool/31525
Call Trace:
__bnxt_hwrm_vnic_set_rss+0xb79/0xe40
bnxt_hwrm_vnic_rss_cfg_p5+0xf7/0x460
__bnxt_setup_vnic_p5+0x12e/0x270
__bnxt_open_nic+0x2262/0x2f30
bnxt_open_nic+0x5d/0xf0
ethnl_set_channels+0x5d4/0xb30
ethnl_default_set_doit+0x2f1/0x620
Core does track the additional contexts in net-next, so we can
move this validation out of the driver as a follow up there.
Fixes: b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20240705020005.681746-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Not all registers in PMU_ALIVE block support atomic set/clear operations.
GS101_SYSIP_DAT0 and GS101_SYSTEM_CONFIGURATION registers are two regs
where attempting atomic access fails.
As documentation on exactly which registers support atomic operations is
not forthcoming. We default to atomic access, unless the register is
explicitly added to the tensor_is_atomic() function. Update the comment
to reflect this as well.
Reviewed-by: Will McVicker <willmcvicker@google.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240628223506.1237523-4-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240702063514.6215-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into soc/drivers
Memory controller drivers for v6.11
Make the Freescale IFC driver selectable because it is used now by two
drivers: Freescale NAND and generic NOR flash. The patches adjusting
defconfig are waiting on the mailing lists to be picked up.
* tag 'memory-controller-drv-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: fsl: replace maintainer
memory: fsl_ifc: Make FSL_IFC config visible and selectable
Link: https://lore.kernel.org/r/20240702070212.8291-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/drivers
Allwinner SoC driver changes for 6.11
- DT binding addition of regulator node under SRAM node
- Cleanup of unused list in SRAM driver
* tag 'sunxi-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
dt-bindings: sram: sunxi-sram: Add regulators child
soc: sunxi: sram: Remove unused list 'claimed_sram'
Link: https://lore.kernel.org/r/ZoQZguQ6taJziJ11@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
soc/drivers
Reset controller updates for v6.11, part 2
This tag adds USB VBUS regulator control for Renesas RZ/G2L SoCs,
which also touches PHY driver and device tree, and pulls in a new
regulator_hardware_enable() helper.
The Tegra BPMP reset driver can be compiled under COMPILE_TEST now.
* tag 'reset-for-v6.11-2' of git://git.pengutronix.de/pza/linux:
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
phy: renesas: phy-rcar-gen3-usb2: Control VBUS for RZ/G2L SoCs
reset: renesas: Add USB VBUS regulator device as child
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document USB VBUS regulator
reset: tegra-bpmp: allow building under COMPILE_TEST
regulator: core: Add helper for allow HW access to enable/disable regulator
Link: https://lore.kernel.org/r/20240703100809.2773890-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
Qualcomm driver updates for v6.11
Support for Shared Memory (shm) Bridge is added, which provides a
stricter interface for handling of buffers passed to TrustZone.
The X1Elite platform is added to uefisecapp allow list, to instantiate
the efivars implementation.
A new in-kernel implementation of the pd-mapper (or servreg) service is
introduced, to replace the userspace dependency for USB Type-C and
battery management.
Support for sharing interrupts across multiple bwmon instances is added,
and a refcount imbalance issue is corrected.
The LLCC support for recent platforms is corrected, and SA8775P support
is added.
A new interface is added to SMEM, to expose "feature codes". One example
of the usecase for this is to indicate to the GPU driver which
frequencies are available on the given device.
The interrupt consumer and provider side of SMP2P is updated to provide
more useful names in interrupt stats.
Support for using the mailbox binding and driver for outgoing IPC
interrupt in the SMSM driver is introduced.
socinfo driver learns about SDM670 and IPQ5321, as well as get some
updates to the X1E PMICs.
pmic_glink is bumped to now support managing 3 USB Type-C ports.
* tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (48 commits)
soc: qcom: smp2p: Use devname for interrupt descriptions
soc: qcom: smsm: Add missing mailbox dependency to Kconfig
soc: qcom: add missing pd-mapper dependencies
soc: qcom: icc-bwmon: Allow for interrupts to be shared across instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Add X1E80100 BWMON instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Remove opp-table from the required list
firmware: qcom: tzmem: export devm_qcom_tzmem_pool_new()
soc: qcom: add pd-mapper implementation
soc: qcom: pdr: extract PDR message marshalling data
soc: qcom: pdr: fix parsing of domains lists
soc: qcom: pdr: protect locator_addr with the main mutex
firmware: qcom: scm: clarify the comment in qcom_scm_pas_init_image()
firmware: qcom: scm: add support for SHM bridge memory carveout
firmware: qcom: tzmem: enable SHM Bridge support
firmware: qcom: scm: add support for SHM bridge operations
firmware: qcom: qseecom: convert to using the TZ allocator
firmware: qcom: scm: make qcom_scm_qseecom_app_get_id() use the TZ allocator
firmware: qcom: scm: make qcom_scm_lmh_dcvsh() use the TZ allocator
firmware: qcom: scm: make qcom_scm_ice_set_key() use the TZ allocator
firmware: qcom: scm: make qcom_scm_assign_mem() use the TZ allocator
...
Link: https://lore.kernel.org/r/20240705034410.13968-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add SCMI ARM REGULATOR configuration for stm32.
Signed-off-by: Pascal Paillet <p.paillet@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240705134554.2833835-1-alexandre.torgue@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/drivers
TI SoC driver updates for v6.11
- Update TISCI protocol URL link which was dead
- socinfo: Add j721E SR 2.0 detection support
- MAINTAINER list additions: ti,pruss.yaml and ti,j721e-system-controller.yaml
- pm33xx: log statement improvement
- knav_qmss: minor data structure optimization
* tag 'ti-driver-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
dt-bindings: soc: ti: Move ti,j721e-system-controller.yaml to soc/ti
MAINTAINERS: Add entry for ti,pruss.yaml to TI KEYSTONE MULTICORE NAVIGATOR DRIVERS
soc: ti: k3-socinfo: Add J721E SR2.0
soc: ti: knav_qmss: Constify struct knav_range_ops
firmware: ti_sci: fix TISCI protocol URL link
dt-bindings: ti: fix TISCI protocol URL link
soc: ti: pm33xx: Fix missing newlines in log statements
Link: https://lore.kernel.org/r/20240705151449.s4rngkehjn73favn@stream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers
RISC-V firmware drivers for v6.11
Microchip:
Support for writing "bitstream info" to the flash using the auto-update
driver. At this point the "bitstream info" is a glorified dtbo wrapper,
but there's plans to add more info there in the future. Additionally,
rework some allocations in the driver and use scope-based cleanup on
them.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-firmware-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
firmware: microchip: use scope-based cleanup where possible
firmware: microchip: move buffer allocation into mpfs_auto_update_set_image_address()
firmware: microchip: support writing bitstream info to flash
Link: https://lore.kernel.org/r/20240707-lukewarm-film-8a9da40a1c27@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers
RISC-V cache drivers for v6.11
StarFive:
A new driver for the cache controller on the jh8100, which didn't
implement Zicbom and thus needs an implementation of non-standard cache
management operations.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-cache-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
MAINTAINERS: add microchip soc binding directory to microchip soc driver entry
MAINTAINERS: add cache binding directory to cache driver entry
cache: Add StarFive StarLink cache management
dt-bindings: cache: Add docs for StarFive Starlink cache controller
Link: https://lore.kernel.org/r/20240707-whoever-undesired-c5f6e96ae403@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into soc/dt
RISC-V Devicetrees for v6.11
Sopgho:
Add clock support for SG2042.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
* tag 'riscv-sophgo-dt-for-v6.11' of https://github.com/sophgo/linux:
riscv: dts: add clock generator for Sophgo SG2042 SoC
Link: https://lore.kernel.org/r/PN1P287MB281861EA2B1706B430D2FA3EFEDB2@PN1P287MB2818.INDP287.PROD.OUTLOOK.COM
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
These are two additional boards, the Xunlong Orange Pi 3B and
the Add Radxa ROCK 3B.
* tag 'v6.11-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
Link: https://lore.kernel.org/r/2191200.GUh0CODmnK@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When running BPF selftests (./test_progs -t sockmap_basic) on a Loongarch
platform, the following kernel panic occurs:
[...]
Oops[#1]:
CPU: 22 PID: 2824 Comm: test_progs Tainted: G OE 6.10.0-rc2+ #18
Hardware name: LOONGSON Dabieshan/Loongson-TC542F0, BIOS Loongson-UDK2018
... ...
ra: 90000000048bf6c0 sk_msg_recvmsg+0x120/0x560
ERA: 9000000004162774 copy_page_to_iter+0x74/0x1c0
CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
PRMD: 0000000c (PPLV0 +PIE +PWE)
EUEN: 00000007 (+FPE +SXE +ASXE -BTE)
ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
BADV: 0000000000000040
PRID: 0014c011 (Loongson-64bit, Loongson-3C5000)
Modules linked in: bpf_testmod(OE) xt_CHECKSUM xt_MASQUERADE xt_conntrack
Process test_progs (pid: 2824, threadinfo=0000000000863a31, task=...)
Stack : ...
Call Trace:
[<9000000004162774>] copy_page_to_iter+0x74/0x1c0
[<90000000048bf6c0>] sk_msg_recvmsg+0x120/0x560
[<90000000049f2b90>] tcp_bpf_recvmsg_parser+0x170/0x4e0
[<90000000049aae34>] inet_recvmsg+0x54/0x100
[<900000000481ad5c>] sock_recvmsg+0x7c/0xe0
[<900000000481e1a8>] __sys_recvfrom+0x108/0x1c0
[<900000000481e27c>] sys_recvfrom+0x1c/0x40
[<9000000004c076ec>] do_syscall+0x8c/0xc0
[<9000000003731da4>] handle_syscall+0xc4/0x160
Code: ...
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception
Kernel relocated by 0x3510000
.text @ 0x9000000003710000
.data @ 0x9000000004d70000
.bss @ 0x9000000006469400
---[ end Kernel panic - not syncing: Fatal exception ]---
[...]
This crash happens every time when running sockmap_skb_verdict_shutdown
subtest in sockmap_basic.
This crash is because a NULL pointer is passed to page_address() in the
sk_msg_recvmsg(). Due to the different implementations depending on the
architecture, page_address(NULL) will trigger a panic on Loongarch
platform but not on x86 platform. So this bug was hidden on x86 platform
for a while, but now it is exposed on Loongarch platform. The root cause
is that a zero length skb (skb->len == 0) was put on the queue.
This zero length skb is a TCP FIN packet, which was sent by shutdown(),
invoked in test_sockmap_skb_verdict_shutdown():
shutdown(p1, SHUT_WR);
In this case, in sk_psock_skb_ingress_enqueue(), num_sge is zero, and no
page is put to this sge (see sg_set_page in sg_set_page), but this empty
sge is queued into ingress_msg list.
And in sk_msg_recvmsg(), this empty sge is used, and a NULL page is got by
sg_page(sge). Pass this NULL page to copy_page_to_iter(), which passes it
to kmap_local_page() and to page_address(), then kernel panics.
To solve this, we should skip this zero length skb. So in sk_msg_recvmsg(),
if copy is zero, that means it's a zero length skb, skip invoking
copy_page_to_iter(). We are using the EFAULT return triggered by
copy_page_to_iter to check for is_fin in tcp_bpf.c.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Suggested-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/e3a16eacdc6740658ee02a33489b1b9d4912f378.1719992715.git.tanggeliang@kylinos.cn
|
|
The GPIO subsystem used to have a serious problem with undefined behavior
and use-after-free bugs on hot-unplug of GPIO chips. This can be
considered a corner-case by some as most GPIO controllers are enabled
early in the boot process and live until the system goes down but most
GPIO drivers do allow unbind over sysfs, many are loadable modules that
can be (force) unloaded and there are also GPIO devices that can be
dynamically detached, for instance CP2112 which is a USB GPIO expender.
Bugs can be triggered both from user-space as well as by in-kernel users.
We have the means of testing it from user-space via the character device
but the issues manifest themselves differently in the kernel.
This is a proposition of adding a new virtual driver - a configurable
GPIO consumer that can be configured over configfs (similarly to
gpio-sim) or described on the device-tree.
This driver is aimed as a helper in spotting any regressions in
hot-unplug handling in GPIOLIB.
Link: https://lore.kernel.org/r/20240708142912.120570-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The return value of __invalid_xchg_size() is assigned to tmp instead of
the return variable x. Assign it to x instead.
Fixes: 2501cf768e4009a0 ("m68k: Fix xchg/cmpxchg to fail to link if given an inappropriate pointer")
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20240702034116.140234-2-thorsten.blum@toblux.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The rebase of commit 09595e0c9d65 ("block: pass a phys_addr_t to
get_max_segment_size") lost adding the total to to the offset in
blk_bvec_map_sg. Add it back.
Fixes: 09595e0c9d65 ("block: pass a phys_addr_t to get_max_segment_size")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Chaitanya Kulkarni <chaitanyak@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240709070126.3019940-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/defconfig
i.MX defconfig change for 6.11:
- Enable a few drivers needed by TQMa7x/MBa7x and i.MX53 QSB/QSRB in
imx_v6_v7_defconfig
- Enable IWLWIFI driver support in arm64 defconfig
* tag 'imx-defconfig-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: Enable the IWLWIFI driver
ARM: imx_v6_v7_defconfig: enable DRM_SII902X and DRM_DISPLAY_CONNECTOR
ARM: imx_v6_v7_defconfig: Enable drivers for TQMa7x/MBa7x
Link: https://lore.kernel.org/r/20240709012534.3106441-1-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Correct the parameter name in the comment of get_max_segment_size()
to fix following warning:-
block/blk-merge.c:220: warning: Function parameter or struct member 'len' not described in 'get_max_segment_size'
block/blk-merge.c:220: warning: Excess function parameter 'max_len' description in 'get_max_segment_size'
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240709045432.8688-1-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The block queue limits validation does this for us now.
The loop_configure() -> WARN_ON_ONCE() call is dropped, as an invalid
block size would trigger this now. We don't want userspace to be able to
directly trigger WARNs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240708091651.177447-6-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The block queue limits validation does this for us now.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240708091651.177447-5-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The block queue limits validation does this for us now.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240708091651.177447-4-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some drivers validate that their own logical block size. It is no harm to
always do this, so validate in blk_validate_limits().
This allows us to remove the validation in most of those drivers.
Add a comment to blk_validate_block_size() to inform users that self-
validation of LBS is usually unnecessary.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240708091651.177447-3-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we fail to read a logical block size in virtblk_read_limits() ->
virtio_cread_feature(), then we default to what is in
lim->logical_block_size, but that would be 0.
We can deal with lim->logical_block_size = 0 later in the
blk_mq_alloc_disk(), but the code in virtblk_read_limits() needs a proper
default, so give a default of SECTOR_SIZE.
Fixes: 27e32cd23fed ("block: pass a queue_limits argument to blk_mq_alloc_disk")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240708091651.177447-2-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
for-6.11/block
Pull NVMe updates from Keith:
"nvme updates for Linux 6.11
- Device initialization memory leak fixes (Keith)
- More constants defined (Weiwen)
- Target debugfs support (Hannes)
- PCIe subsystem reset enhancements (Keith)
- Queue-depth multipath policy (Redhat and PureStorage)
- Implement get_unique_id (Christoph)
- Authentication error fixes (Gaosheng)"
* tag 'nvme-6.11-2024-07-08' of git://git.infradead.org/nvme: (21 commits)
nvmet-auth: fix nvmet_auth hash error handling
nvme: implement ->get_unique_id
nvme-multipath: implement "queue-depth" iopolicy
nvme-multipath: prepare for "queue-depth" iopolicy
nvme-pci: do not directly handle subsys reset fallout
lpfc_nvmet: implement 'host_traddr'
nvme-fcloop: implement 'host_traddr'
nvmet-fc: implement host_traddr()
nvmet-rdma: implement host_traddr()
nvmet-tcp: implement host_traddr()
nvmet: add 'host_traddr' callback for debugfs
nvmet: add debugfs support
mailmap: add entry for Weiwen Hu
nvme: rename CDR/MORE/DNR to NVME_STATUS_*
nvme: fix status magic numbers
nvme: rename nvme_sc_to_pr_err to nvme_status_to_pr_err
nvme: split device add from initialization
nvme: fc: split controller bringup handling
nvme: rdma: split controller bringup handling
nvme: tcp: split controller bringup handling
...
|
|
Remove assignment from IS_ERR() argument.
This is detected by coccinelle.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240708080404.3859094-1-nichen@iscas.ac.cn
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Reinit PHY after cable test, otherwise link can't be established on
tested port. This issue is reproducible on LAN9372 switches with
integrated 100BaseT1 PHYs.
Fixes: 788050256c411 ("net: phy: microchip_t1: add cable test support for lan87xx phy")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240705084954.83048-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
