Age | Commit message (Collapse) | Author |
|
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 0e674aeb0b77 ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Tx side sets EOP and RS bits on descriptors to indicate that a
particular descriptor is the last one and needs to generate an irq when
it was sent. These bits should not be checked on completion path
regardless whether it's the Tx or the Rx. DD bit serves this purpose and
it indicates that a particular descriptor is either for Rx or was
successfully Txed. EOF is also set as loopback test does not xmit
fragmented frames.
Look at (DD | EOF) bits setting in ice_lbtest_receive_frames() instead
of EOP and RS pair.
Fixes: 0e674aeb0b77 ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver currently does not allow two VSIs in the same PF domain
to have the same unicast MAC address. This is incorrect in the sense
that a policy decision is being made in the driver when it must be
left to the user. This approach was causing issues when rebooting
the system with VFs spawned not being able to change their MAC addresses.
Such errors were present in dmesg:
[ 7921.068237] ice 0000:b6:00.2 ens2f2: Unicast MAC 6a:0d:e4:70:ca:d1 already
exists on this PF. Preventing setting VF 7 unicast MAC address to 6a:0d:e4:70:ca:d1
Fix that by removing this restriction. Doing this also allows
us to remove some additional code that's checking if a unicast MAC
filter already exists.
Fixes: 47ebc7b02485 ("ice: Check if unicast MAC exists before setting VF MAC")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.
Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect
Offload params: td_offset, cd_tunnel_params were
corrupted, due to l4 header pointing wrong address. NIC would then drop
those packets internally, due to incorrect TX descriptor data,
which increased GLV_TEPC register.
Fixes: 69e66c04c672 ("ice: Add mpls+tso support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Legacy VLAN implementation allows for untrusted VF to have 8 VLAN
filters, not counting VLAN 0 filters. Current VLAN_V2 implementation
lowers available filters for VF, by counting in VLAN 0 filter for both
TPIDs.
Fix this by counting only non zero VLAN filters.
Without this patch, untrusted VF would not be able to access 8 VLAN
filters.
Fixes: cc71de8fa133 ("ice: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Trying to use 'queue' statement in ingress (for example)
triggers a splat on reinject:
WARNING: CPU: 3 PID: 1345 at net/netfilter/nf_queue.c:291
... because nf_reinject cannot find the ruleset head.
The netdev family doesn't support async resume at the moment anyway,
so disallow loading such rulesets with a more appropriate
error message.
v2: add 'validate' callback and also check hook points, v1 did
allow ingress use in 'table inet', but that doesn't work either. (Pablo)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add explicit rescheduling points during ruleset walk.
Switching to a faster algorithm is possible but this is a much
smaller change, suitable for nf tree.
Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1460
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
offset
Domingo Dirutigliano and Nicola Guerrera report kernel panic when
sending nf_queue verdict with 1-byte nfta_payload attribute.
The IP/IPv6 stack pulls the IP(v6) header from the packet after the
input hook.
If user truncates the packet below the header size, this skb_pull() will
result in a malformed skb (skb->len < 0).
Fixes: 7af4cc3fa158 ("[NETFILTER]: Add "nfnetlink_queue" netfilter queue handler over nfnetlink")
Reported-by: Domingo Dirutigliano <pwnzer0tt1@proton.me>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fix from Alexander GordeevL
- Prevent relatively slow PRNO TRNG random number operation from being
called from interrupt context. That could for example cause some
network loads to timeout.
* tag 's390-5.19-7' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/archrandom: prevent CPACF trng invocations in interrupt context
|
|
The vmf->page can be NULL when the wp_page_reuse() is invoked by
wp_pfn_shared(), it will cause the following panic:
BUG: kernel NULL pointer dereference, address: 000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 18 PID: 923 Comm: Xorg Not tainted 5.19.0-rc8.bm.1-amd64 #263
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g14
RIP: 0010:_compound_head+0x0/0x40
[...]
Call Trace:
wp_page_reuse+0x1c/0xa0
do_wp_page+0x1a5/0x3f0
__handle_mm_fault+0x8cf/0xd20
handle_mm_fault+0xd5/0x2a0
do_user_addr_fault+0x1d0/0x680
exc_page_fault+0x78/0x170
asm_exc_page_fault+0x22/0x30
To fix it, this patch performs a NULL pointer check before dereferencing
the vmf->page.
Fixes: 6c287605fd56 ("mm: remember exclusively mapped anonymous pages with PG_anon_exclusive")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When booting a kernel compiled with clang's CFI protection
(CONFIG_CFI_CLANG), there is a CFI failure in
drm_simple_kms_crtc_mode_valid() when trying to call
simpledrm_simple_display_pipe_mode_valid() through ->mode_valid():
[ 0.322802] CFI failure (target: simpledrm_simple_display_pipe_mode_valid+0x0/0x8):
...
[ 0.324928] Call trace:
[ 0.324969] __ubsan_handle_cfi_check_fail+0x58/0x60
[ 0.325053] __cfi_check_fail+0x3c/0x44
[ 0.325120] __cfi_slowpath_diag+0x178/0x200
[ 0.325192] drm_simple_kms_crtc_mode_valid+0x58/0x80
[ 0.325279] __drm_helper_update_and_validate+0x31c/0x464
...
The ->mode_valid() member in 'struct drm_simple_display_pipe_funcs'
expects a return type of 'enum drm_mode_status', not 'int'. Correct it
to fix the CFI failure.
Cc: stable@vger.kernel.org
Fixes: 11e8f5fd223b ("drm: Add simpledrm driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1647
Reported-by: Tomasz Paweł Gajc <tpgxyz@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220725233629.223223-1-nathan@kernel.org
|
|
After commit b6c02ef54913 ("bridge: Netlink interface fix."),
br_fill_ifinfo() started to send an empty IFLA_AF_SPEC attribute when a
bridge vlan dump is requested but an interface does not have any vlans
configured.
iproute2 ignores such an empty attribute since commit b262a9becbcb
("bridge: Fix output with empty vlan lists") but older iproute2 versions as
well as other utilities have their output changed by the cited kernel
commit, resulting in failed test cases. Regardless, emitting an empty
attribute is pointless and inefficient.
Avoid this change by canceling the attribute if no AF_SPEC data was added.
Fixes: b6c02ef54913 ("bridge: Netlink interface fix.")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220725001236.95062-1-bpoirier@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The double `if' is duplicated in line 104, remove one.
Signed-off-by: Xin Gao <gaoxin@cdjrlc.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220722194639.18545-1-gaoxin@cdjrlc.com
|
|
Add checks verifying number of inodes stored in the superblock matches
the number computed from number of inodes per group. Also verify we have
at least one block worth of inodes per group. This prevents crashes on
corrupted filesystems.
Reported-by: syzbot+d273f7d7f58afd93be48@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Subbaraya Sundeep says:
====================
Octeontx2 minor tc fixes
This patch set fixes two problems found in tc code
wrt to ratelimiting and when installing UDP/TCP filters.
Patch 1: CN10K has different register format compared to
CN9xx hence fixes that.
Patch 2: Check flow mask also before installing a src/dst
port filter, otherwise installing for one port installs for other one too.
====================
Link: https://lore.kernel.org/r/1658650874-16459-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.
Fixes: 1d4d9e42c240 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.
Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.
Fixes: e638a83f167e ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since commit 27b3a5c51b50 ("kill-the-bkl/reiserfs: drop the fs race
watchdog from _get_block_create_0()"), which removed a label that may
have the pointer 'p' touched in its control flow, related if statements
now eval to constant value now. Just remove them.
Assigning value NULL to p here
293 char *p = NULL;
In the following conditional expression, the value of p is always NULL,
As a result, the kunmap() cannot be executed.
308 if (p)
309 kunmap(bh_result->b_page);
355 if (p)
356 kunmap(bh_result->b_page);
366 if (p)
367 kunmap(bh_result->b_page);
Also, the kmap() cannot be executed.
399 if (!p)
400 p = (char *)kmap(bh_result->b_page);
[JK: Removed unnecessary initialization of 'p' to NULL]
Signed-off-by: Zeng Jingxiang <linuszeng@tencent.com>
Signed-off-by: Kairui Song <kasong@tencent.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220720083029.1065578-1-zengjx95@gmail.com
|
|
There are sleep in atomic context bugs in timer handlers of sctp
such as sctp_generate_t3_rtx_event(), sctp_generate_probe_event(),
sctp_generate_t1_init_event(), sctp_generate_timeout_event(),
sctp_generate_t3_rtx_event() and so on.
The root cause is sctp_sched_prio_init_sid() with GFP_KERNEL parameter
that may sleep could be called by different timer handlers which is in
interrupt context.
One of the call paths that could trigger bug is shown below:
(interrupt context)
sctp_generate_probe_event
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_outq_teardown
sctp_outq_init
sctp_sched_set_sched
n->init_sid(..,GFP_KERNEL)
sctp_sched_prio_init_sid //may sleep
This patch changes gfp_t parameter of init_sid in sctp_sched_set_sched()
from GFP_KERNEL to GFP_ATOMIC in order to prevent sleep in atomic
context bugs.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/20220723015809.11553-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to an invalid conflict resolution on my side while working on 2
different series (LAG FDBs and FDB isolation), dsa_switch_do_lag_fdb_add()
does not store the database associated with a dsa_mac_addr structure.
So after adding an FDB entry associated with a LAG, dsa_mac_addr_find()
fails to find it while deleting it, because &a->db is zeroized memory
for all stored FDB entries of lag->fdbs, and dsa_switch_do_lag_fdb_del()
returns -ENOENT rather than deleting the entry.
Fixes: c26933639b54 ("net: dsa: request drivers to perform FDB isolation")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220723012411.1125066-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the inability to bring an interface up on a setup with
only MSI interrupts enabled (no MSI-X).
Solution is to add a default number of QPs = 1. This is enough,
since without MSI-X support driver enables only a basic feature set.
Fixes: bc6d33c8d93f ("i40e: Fix the number of queues available to be mapped for use")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220722175401.112572-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit d11219ad53dc ("amdgpu: disable powerpc support for the newer
display engine") disabled the DCN driver for all of powerpc due to
unresolved build failures with some compilers.
Further digging shows that the build failures only occur with compilers
that default to 64-bit long double.
Both the ppc64 and ppc64le ABIs define long double to be 128-bits, but
there are compilers in the wild that default to 64-bits. The compilers
provided by the major distros (Fedora, Ubuntu) default to 128-bits and
are not affected by the build failure.
There is a compiler flag to force 128-bit long double, which may be the
correct long term fix, but as an interim fix only allow building the DCN
driver if long double is 128-bits by default.
The bisection in commit d11219ad53dc must have gone off the rails at
some point, the build failure occurs all the way back to the original
commit that enabled DCN support on powerpc, at least with some
toolchains.
Depends-on: d11219ad53dc ("amdgpu: disable powerpc support for the newer display engine")
Fixes: 16a9dea110a6 ("amdgpu: Enable initial DCN support on POWER")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Dan Horák <dan@danny.cz>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2100
Link: https://lore.kernel.org/r/20220725123918.1903255-1-mpe@ellerman.id.au
|
|
Commit 32d4fd5751ea ("cpuidle,intel_idle: Fix CPUIDLE_FLAG_IRQ_ENABLE")
uses raw_local_irq_enable/local_irq_disable() around call to
__intel_idle() in intel_idle_irq().
With interrupt enabled, timer tick interrupt can happen and a
subsequently call to __do_softirq() may change the lockdep hardirqs state
of a debug kernel back to 'on'. This will result in a mismatch between
the cpu hardirqs state (off) and the lockdep hardirqs state (on) causing
a number of false positive "WARNING: suspicious RCU usage" splats.
Fix that by using local_irq_disable() to disable interrupt in
intel_idle_irq().
Fixes: 32d4fd5751ea ("cpuidle,intel_idle: Fix CPUIDLE_FLAG_IRQ_ENABLE")
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For execlists backend, current implementation of Wa_22011802037 is to
stop the CS before doing a reset of the engine. This WA was further
extended to wait for any pending MI FORCE WAKEUPs before issuing a
reset. Add the extended steps in the execlist path of reset.
In addition, extend the WA to gen11.
v2: (Tvrtko)
- Clarify comments, commit message, fix typos
- Use IS_GRAPHICS_VER for gen 11/12 checks
v3: (Daneile)
- Drop changes to intel_ring_submission since WA does not apply to it
- Log an error if MSG IDLE is not defined for an engine
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Fixes: f6aa0d713c88 ("drm/i915: Add Wa_22011802037 force cs halt")
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621192105.2100585-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 0667429ce68e0b08f9f1fec8fd0b1f57228f605e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Kuniyuki Iwashima says:
====================
sysctl: Fix data-races around ipv4_net_table (Round 6, Final).
This series fixes data-races around 11 knobs after tcp_pacing_ss_ratio
ipv4_net_table, and this is the final round for ipv4_net_table.
While at it, other data-races around these related knobs are fixed.
- decnet_mem
- decnet_rmem
- tipc_rmem
There are still 58 tables possibly missing some fixes under net/.
$ grep -rnE "struct ctl_table.*?\[\] =" net/ | wc -l
60
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_fib_notify_on_flag_change, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 680aea08e78c ("net: ipv4: Emit notification when fib hardware flags are changed")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tcp_reflect_tos, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: ac8f1710c12b ("tcp: reflect tos value received in SYN to the socket")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tcp_comp_sack_nr, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 9c21d2fc41c0 ("tcp: add tcp_comp_sack_nr sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tcp_comp_sack_slack_ns, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: a70437cc09a1 ("tcp: add hrtimer slack to sack compression")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tcp_comp_sack_delay_ns, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 6d82aa242092 ("tcp: add tcp_comp_sack_delay_ns sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading these sysctl variables, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- .sysctl_rmem
- .sysctl_rwmem
- .sysctl_rmem_offset
- .sysctl_wmem_offset
- sysctl_tcp_rmem[1, 2]
- sysctl_tcp_wmem[1, 2]
- sysctl_decnet_rmem[1]
- sysctl_decnet_wmem[1]
- sysctl_tipc_rmem[1]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While reading sysctl_tcp_pacing_(ss|ca)_ratio, they can be changed
concurrently. Thus, we need to add READ_ONCE() to their readers.
Fixes: 43e122b014c9 ("tcp: refine pacing rate determination")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mld_{query | report}_work() processes queued events.
If there are too many events in the queue, it re-queue a work.
And then, it returns without in6_dev_put().
But if queuing is failed, it should call in6_dev_put(), but it doesn't.
So, a reference count leak would occur.
THREAD0 THREAD1
mld_report_work()
spin_lock_bh()
if (!mod_delayed_work())
in6_dev_hold();
spin_unlock_bh()
spin_lock_bh()
schedule_delayed_work()
spin_unlock_bh()
Script to reproduce(by Hangbin Liu):
ip netns add ns1
ip netns add ns2
ip netns exec ns1 sysctl -w net.ipv6.conf.all.force_mld_version=1
ip netns exec ns2 sysctl -w net.ipv6.conf.all.force_mld_version=1
ip -n ns1 link add veth0 type veth peer name veth0 netns ns2
ip -n ns1 link set veth0 up
ip -n ns2 link set veth0 up
for i in `seq 50`; do
for j in `seq 100`; do
ip -n ns1 addr add 2021:${i}::${j}/64 dev veth0
ip -n ns2 addr add 2022:${i}::${j}/64 dev veth0
done
done
modprobe -r veth
ip -a netns del
splat looks like:
unregister_netdevice: waiting for veth0 to become free. Usage count = 2
leaked reference.
ipv6_add_dev+0x324/0xec0
addrconf_notify+0x481/0xd10
raw_notifier_call_chain+0xe3/0x120
call_netdevice_notifiers+0x106/0x160
register_netdevice+0x114c/0x16b0
veth_newlink+0x48b/0xa50 [veth]
rtnl_newlink+0x11a2/0x1a40
rtnetlink_rcv_msg+0x63f/0xc00
netlink_rcv_skb+0x1df/0x3e0
netlink_unicast+0x5de/0x850
netlink_sendmsg+0x6c9/0xa90
____sys_sendmsg+0x76a/0x780
__sys_sendmsg+0x27c/0x340
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: f185de28d9ae ("mld: add new workqueues for process mld events")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macsec_add_txsa()
init_rx_sa() allocates relevant resource for rx_sa->stats and rx_sa->
key.tfm with alloc_percpu() and macsec_alloc_tfm(). When some error
occurs after init_rx_sa() is called in macsec_add_rxsa(), the function
released rx_sa with kfree() without releasing rx_sa->stats and rx_sa->
key.tfm, which will lead to a resource leak.
We should call macsec_rxsa_put() instead of kfree() to decrease the ref
count of rx_sa and release the relevant resource if the refcount is 0.
The same bug exists in macsec_add_txsa() for tx_sa as well. This patch
fixes the above two bugs.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sabrina Dubroca says:
====================
macsec: fix config issues
The patch adding netlink support for XPN (commit 48ef50fa866a
("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)"))
introduced several issues, including a kernel panic reported at [1].
Reproducing those bugs with upstream iproute is limited, since iproute
doesn't currently support XPN. I'm also working on this.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=208315
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, MACSEC_SA_ATTR_PN is handled inconsistently, sometimes as a
u32, sometimes forced into a u64 without checking the actual length of
the attribute. Instead, we can use nla_get_u64 everywhere, which will
read up to 64 bits into a u64, capped by the actual length of the
attribute coming from userspace.
This fixes several issues:
- the check in validate_add_rxsa doesn't work with 32-bit attributes
- the checks in validate_add_txsa and validate_upd_sa incorrectly
reject X << 32 (with X != 0)
Fixes: 48ef50fa866a ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1AEbw-2013 (section 10.7.8) specifies that the maximum value
of the replay window is 2^30-1, to help with recovery of the upper
bits of the PN.
To avoid leaving the existing macsec device in an inconsistent state
if this test fails during changelink, reuse the cleanup mechanism
introduced for HW offload. This wasn't needed until now because
macsec_changelink_common could not fail during changelink, as
modifying the cipher suite was not allowed.
Finally, this must happen after handling IFLA_MACSEC_CIPHER_SUITE so
that secy->xpn is set.
Fixes: 48ef50fa866a ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The expected length is MACSEC_SALT_LEN, not MACSEC_SA_ATTR_SALT.
Fixes: 48ef50fa866a ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 48ef50fa866a added a test on tb_sa[MACSEC_SA_ATTR_PN], but
nothing guarantees that it's not NULL at this point. The same code was
added to macsec_add_txsa, but there it's not a problem because
validate_add_txsa checks that the MACSEC_SA_ATTR_PN attribute is
present.
Note: it's not possible to reproduce with iproute, because iproute
doesn't allow creating an SA without specifying the PN.
Fixes: 48ef50fa866a ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208315
Reported-by: Frantisek Sumsal <fsumsal@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a quirk for the Crucial P2.
Signed-off-by: Tobias Gruetzmacher <tobias-git@23.gs>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Merge v5.19-rc7 into fixes to bring in:
d11219ad53dc ("amdgpu: disable powerpc support for the newer display engine")
|
|
Since commit 1033990ac5b2 ("sctp: implement memory accounting on tx path"),
SCTP has supported memory accounting on tx path where 'sctp_wmem' is used
by sk_wmem_schedule(). So we should fix the description for this option in
ip-sysctl.rst accordingly.
v1->v2:
- Improve the description as Marcelo suggested.
Fixes: 1033990ac5b2 ("sctp: implement memory accounting on tx path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tls_device_down takes a reference on all contexts it's going to move to
the degraded state (software fallback). If sk_destruct runs afterwards,
it can reduce the reference counter back to 1 and return early without
destroying the context. Then tls_device_down will release the reference
it took and call tls_device_free_ctx. However, the context will still
stay in tls_device_down_list forever. The list will contain an item,
memory for which is released, making a memory corruption possible.
Fix the above bug by properly removing the context from all lists before
any call to tls_device_free_ctx.
Fixes: 3740651bf7e2 ("tls: Fix context leak on tls_device_down")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This code requires x509_load_certificate_list() to be built-in.
Fixes: 60050ffe3d77 ("certs: Move load_certificate_list() to be with the asymmetric keys code")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Link: https://lore.kernel.org/all/202206221515.DqpUuvbQ-lkp@intel.com/
Link: https://lore.kernel.org/all/20220712104554.408dbf42@gandalf.local.home/
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Borislav Petkov:
- Reorganize the perf LBR init code so that a TSX quirk is applied
early enough in order for the LBR MSR access to not #GP
* tag 'perf_urgent_for_v5.19_rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/lbr: Fix unchecked MSR access error on HSW
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
"A single fix to correct a wrong BUG_ON() condition for deboosted
tasks"
* tag 'sched_urgent_for_v5.19_rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix BUG_ON condition for deboosted tasks
|