| Age | Commit message (Collapse) | Author |
|---|
|
Hayes Wang says:
====================
r8152: fix rx issues
The two patched are used to fix rx issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set rx mode before calling netif_wake_queue() when linking on to avoid
the device missing the receiving packets.
The transmission may start after calling netif_wake_queue(), and the
packets of resopnse may reach before calling rtl8152_set_rx_mode()
which let the device could receive packets. Then, the packets of
response would be missed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device could only check the checksum of TCP and UDP packets. Therefore,
for the IPv4 packets excluding TCP and UDP, the check of checksum is necessary,
even though the IP checksum is correct.
Take ICMP for example, The IP checksum may be correct, but the ICMP checksum
may be wrong.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data pointer in the config space TLV parser already includes
NFP_NET_CFG_TLV_BASE, it should not be added again. Incorrect
offset values were only used in printed user output, rendering
the bug merely cosmetic.
Fixes: 73a0329b057e ("nfp: add TLV capabilities to the BAR")
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter
- make JMicron JMB38x controllers work with IOMMU-equipped systems
- IP-over-1394: allow user-configured MTU of up to 4096 bytes
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire-ohci: work around oversized DMA reads on JMicron controllers
firewire: net: max MTU off by one
|
|
The declaration for swsusp_arch_resume marks it as 'asmlinkage', but the
definition in x86-32 does not, and it fails to include the header with the
declaration. This leads to a warning when building with
link-time-optimizations:
kernel/power/power.h:108:23: error: type of 'swsusp_arch_resume' does not match original declaration [-Werror=lto-type-mismatch]
extern asmlinkage int swsusp_arch_resume(void);
^
arch/x86/power/hibernate_32.c:148:0: note: 'swsusp_arch_resume' was previously declared here
int swsusp_arch_resume(void)
This moves the declaration into a globally visible header file and fixes up
both x86 definitions to match it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lkml.kernel.org/r/20180202145634.200291-2-arnd@arndb.de
|
|
In some configurations, 'partial' does not get initialized, as shown by
this gcc-8 warning:
arch/x86/kernel/dumpstack.c: In function 'show_trace_log_lvl':
arch/x86/kernel/dumpstack.c:156:4: error: 'partial' may be used uninitialized in this function [-Werror=maybe-uninitialized]
show_regs_if_on_stack(&stack_info, regs, partial);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This initializes it to false, to get the previous behavior in this case.
Fixes: a9cdbe72c4e8 ("x86/dumpstack: Fix partial register dumps")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Link: https://lkml.kernel.org/r/20180202145634.200291-1-arnd@arndb.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.16 kernel cycle.
Like with GPIO it is actually a bit calm this time.
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and
pinctrl_force_sleep() reprogram the states into the hardware of any
hogged pins, even if they are already in the desired state.
This only apply to hogged pins since groups of pins owned by
drivers need to be managed by each driver, lest they could not do
things like runtime PM and put pins to sleeping state even if the
system as a whole is not in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is a
mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for
routers, repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
has multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels
etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes"
* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
pinctrl: mcp23s08: fix irq setup order
pinctrl: Forward declare struct device
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
pinctrl: stm32: add STM32F769 MCU support
pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
pinctrl: sx150x: Register pinctrl before adding the gpiochip
pinctrl: sx150x: Unregister the pinctrl on release
pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
pinctrl: uniphier: refactor drive strength get/set functions
pinctrl: imx7ulp: constify struct imx_cfg_params_decode
pinctrl: imx: constify struct imx_pinctrl_soc_info
pinctrl: imx7d: simplify imx7d_pinctrl_probe
pinctrl: imx: use struct imx_pinctrl_soc_info as a const
pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
pinctrl: qcom: Add msm8998 pinctrl driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle. I've pushed the at32ap700x removal late but it is
unlikely to cause any issues.
Summary:
Subsystem:
- Move ABI documentation to Documentation/ABI
New driver:
- NXP i.MX53 SRTC
- Chrome OS EC RTC
Drivers:
- Remove at32ap700x
- Many fixes in various error paths"
* tag 'rtc-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: remove rtc-at32ap700x
Documentation: rtc: move iotcl interface documentation to ABI
Documentation: rtc: add sysfs file permissions
Documentation: rtc: move sysfs documentation to ABI
rtc: mxc_v2: remove __exit annotation
rtc: mxc_v2: Remove unnecessary platform_get_resource() error check
rtc: add mxc driver for i.MX53 SRTC
dt-bindings: rtc: add bindings for i.MX53 SRTC
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_set_time
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_read_time
rtc: omap: fix unbalanced clk_prepare_enable/clk_disable_unprepare
rtc: ac100: Fix multiple race conditions
rtc: sun6i: ensure rtc is kfree'd on error
rtc: cros-ec: add cros-ec-rtc driver.
mfd: cros_ec: Introduce RTC commands and events definitions.
rtc: stm32: Fix copyright
rtc: Remove unused RTC_DEVICE_NAME_SIZE
rtc: r9701: Remove r9701_remove function
rtc: brcmstb-waketimer: fix error handling in brcmstb_waketmr_probe()
|
|
Fixes: 117cc7a908c83 ("x86/retpoline: Fill return stack buffer on vmexit")
Signed-off-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180202191220.blvgkgutojecxr3b@starbug-vm.ie.oracle.com
|
|
I'm seeing build failures from the two newly introduced arrays that
are marked 'const' and '__initdata', which are mutually exclusive:
arch/x86/kernel/cpu/common.c:882:43: error: 'cpu_no_speculation' causes a section type conflict with 'e820_table_firmware_init'
arch/x86/kernel/cpu/common.c:895:43: error: 'cpu_no_meltdown' causes a section type conflict with 'e820_table_firmware_init'
The correct annotation is __initconst.
Fixes: fec9434a12f3 ("x86/pti: Do not enable PTI on CPUs which are not vulnerable to Meltdown")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180202213959.611210-1-arnd@arndb.de
|
|
A NULL pointer reference kernel bug was observed when
acpi_nfit_add_dimm() called in acpi_nfit_register_dimms() failed. This
error path does not set nfit_mem->nvdimm, but the 2nd
list_for_each_entry() loop in the function assumes it's always set. Add
a check to nfit_mem->nvdimm.
Cc: <stable@vger.kernel.org>
Fixes: ba9c8dd3c222 ("acpi, nfit: add dimm device notification support")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"A few small fixes and clean ups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix crash if pthread_create races with signal delivery
alpha: fix formating of stack content
alpha: fix reboot on Avanti platform
alpha: deprecate pci_get_bus_and_slot()
alpha: Fix mixed up args in EXC macro in futex operations
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
alpha: make thread_saved_pc static
alpha: make XTABS equivalent to TAB3
|
|
Sync tools/arch/x86/include/asm/{cpu,disabled-,required-}features.h with
the changes in:
2961298efe1e ("x86/cpufeatures: Clean up Spectre v2 related CPUID flags")
20ffa1caecca ("x86/speculation: Add basic IBPB (Indirect Branch Prediction Barrier) support")
5d10cbc91d9e ("x86/cpufeatures: Add AMD feature bits for Speculation Control")
fc67dd70adb7 ("x86/cpufeatures: Add Intel feature bits for Speculation Control")
95ca0ee86360 ("x86/cpufeatures: Add CPUID_7_EDX CPUID leaf")
a511e7935378 ("x86/intel_rdt: Enumerate L2 Code and Data Prioritization (CDP) feature")
4fdec2034b75 ("x86/cpufeature: Move processor tracing out of scattered features")
c995efd5a740 ("x86/retpoline: Fill RSB on context switch for affected CPUs")
76b043848fd2 ("x86/retpoline: Add initial retpoline support")
99c6fa2511d8 ("x86/cpufeatures: Add X86_BUG_SPECTRE_V[12]")
de791821c295 ("x86/pti: Rename BUG_CPU_INSECURE to BUG_CPU_MELTDOWN")
6cff64b86aaa ("x86/mm: Use INVPCID for __native_flush_tlb_single()")
None will entail changes in the tools/perf/, synchronizing to elliminate
these perf build warnings:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/disabled-features.h' differs from latest version at 'arch/x86/include/asm/disabled-features.h'
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/required-features.h' differs from latest version at 'arch/x86/include/asm/required-features.h'
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-dbdjack1k92xar5ccuq4el1h@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To get the tools copy updated with the changes in 34be39305a77
("sched/deadline: Implement "runtime overrun signal" support"), that
cause no effect on the tools, will be used when we start copying the
sched_attr struct argument to the sched_get/setattr syscalls.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-8rododhs87x8hv9k83qcdtne@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The changes in the 3214d01f139b ("KVM: PPC: Book3S: Provide information
about hardware/firmware CVE workarounds") commit right now will not
produce any change in the tools, but that is because we still need to
improve tools/perf/trace/beauty/kvm_ioctl.sh to build per arch string
tables, so that we avoid assigning multiple times to the same command
string entry, i.e. multiple defines, for different arches, have the same
value, causing this:
In file included from trace/beauty/ioctl.c:82:0:
/tmp/build/perf/trace/beauty/generated/ioctl/kvm_ioctl_array.c: In function ‘ioctl__scnprintf_kvm_cmd’:
/tmp/build/perf/trace/beauty/generated/ioctl/kvm_ioctl_array.c:76:11: error: initialized field overwritten [-Werror=override-init]
/tmp/build/perf/trace/beauty/generated/ioctl/kvm_ioctl_array.c:88:11: note: (near initialization for ‘kvm_ioctl_cmds[165]’)
/tmp/build/perf/trace/beauty/generated/ioctl/kvm_ioctl_array.c:90:11: error: initialized field overwritten [-Werror=override-init]
[0xa6] = "PPC_GET_SMMU_INFO",
^~~~~~~~~~~~~~~~~~~
So the onlye effect of updating the tools/ copy of ppc's kvm.h header
is to silence these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
Warning: Kernel ABI header at 'tools/arch/powerpc/include/uapi/asm/kvm.h' differs from latest version at 'arch/powerpc/include/uapi/asm/kvm.h'
At some point we should do what we did for the errno tables and create
per-arch string translation tables for the KVM ioctl commands for the
architectures supporting KVM, such as s/390, PowerPC, x86_64 and ARM.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-jmcf78tqiudgn46zqfw2tgt2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The 35b3fde6203b ("KVM: s390: wire up bpb feature") was noticed by the
perf build process:
Warning: Kernel ABI header at 'tools/arch/s390/include/uapi/asm/kvm.h' differs from latest version at 'arch/s390/include/uapi/asm/kvm.h'
The changes in this cset don't cause or require changes in tools/perf/,
so just update the copy to silence the build warning.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-kif2fdkcaewj8iqw6lwyil8s@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick up the changes from this cset:
823dbb6eb08a ("ALSA: pcm: add SNDRV_PCM_FORMAT_{S,U}20")
It doesn't affect how the tools are built, this os done just to silence
this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
Right now tools/perf uses this header to generate string tables to
translate ioctl commands in 'perf trace', see
tools/perf/trace/beauty/sndrv_pcm_ioctl.sh, here is an example
of a strace like system wide session, for one second:
# perf trace -a -e ioctl sleep 1
0.000 ( 0.019 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
0.081 ( 0.006 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
0.092 ( 0.006 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_STATUS_EXT, arg: 0x7f6745ec4ae0) = 0
10.178 ( 0.013 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
10.229 ( 0.005 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
10.238 ( 0.013 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_STATUS_EXT, arg: 0x7f6745ec4ae0) = 0
10.368 ( 0.009 ms): threaded-ml/26440 ioctl(fd: 141<socket:[111353]>, cmd: TIOCLINUX, arg: 0x7f8f70d2e1a4) = 0
10.495 ( 0.018 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
10.526 ( 0.005 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
19.695 ( 0.018 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
19.757 ( 0.006 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_HWSYNC, arg: 0x107b) = 0
19.767 ( 0.005 ms): alsa-sink-HDMI/4219 ioctl(fd: 47</dev/snd/pcmC0D8p>, cmd: SNDRV_PCM_STATUS_EXT, arg: 0x7f6745ec4ae0) = 0
<BIG SNIP>
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-sfpeesn8w0pyn3fe7vf2xmfl@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
|
|
Pull ARM updates from Russell King:
- StrongARM SA1111 updates to modernise and remove cruft
- Add StrongARM gpio drivers for board GPIOs
- Verify size of zImage is what we expect to avoid issues with
appended DTB
- nommu updates from Vladimir Murzin
- page table read-write-execute checking from Jinbum Park
- Broadcom Brahma-B15 cache updates from Florian Fainelli
- Avoid failure with kprobes test caused by inappropriately
placed kprobes
- Remove __memzero optimisation (which was incorrectly being
used directly by some drivers)
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8745/1: get rid of __memzero()
ARM: 8744/1: don't discard memblock for kexec
ARM: 8743/1: bL_switcher: add MODULE_LICENSE tag
ARM: 8742/1: Always use REFCOUNT_FULL
ARM: 8741/1: B15: fix unused label warnings
ARM: 8740/1: NOMMU: Make sure we do not hold stale data in mem[] array
ARM: 8739/1: NOMMU: Setup VBAR/Hivecs for secondaries cores
ARM: 8738/1: Disable CONFIG_DEBUG_VIRTUAL for NOMMU
ARM: 8737/1: mm: dump: add checking for writable and executable
ARM: 8736/1: mm: dump: make the page table dumping seq_file
ARM: 8735/1: mm: dump: make page table dumping reusable
ARM: sa1100/neponset: add GPIO drivers for control and modem registers
ARM: sa1100/assabet: add BCR/BSR GPIO driver
ARM: 8734/1: mm: idmap: Mark variables as ro_after_init
ARM: 8733/1: hw_breakpoint: Mark variables as __ro_after_init
ARM: 8732/1: NOMMU: Allow userspace to access background MPU region
ARM: 8727/1: MAINTAINERS: Update brcmstb entries to cover B15 code
ARM: 8728/1: B15: Register reboot notifier for KEXEC
ARM: 8730/1: B15: Add suspend/resume hooks
ARM: 8726/1: B15: Add CPU hotplug awareness
...
|
|
Pull microblaze updates from Michal Simek:
- Fix endian handling and Kconfig dependency
- Fix iounmap prototype
* tag 'microblaze-4.16-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Setup proper dependency for optimized lib functions
microblaze: fix iounmap prototype
microblaze: fix endian handling
|
|
skd includes slab_def.h to get access to the slab cache object size.
However, including this header breaks when we use SLUB or SLOB instead of
the SLAB allocator, since the structure layout is completely different,
as shown by this warning when we build this driver in one of the invalid
configurations with link-time optimizations enabled:
include/linux/slab.h:715:0: error: type of 'kmem_cache_size' does not match original declaration [-Werror=lto-type-mismatch]
unsigned int kmem_cache_size(struct kmem_cache *s);
mm/slab_common.c:77:14: note: 'kmem_cache_size' was previously declared here
unsigned int kmem_cache_size(struct kmem_cache *s)
^
mm/slab_common.c:77:14: note: code may be misoptimized unless -fno-strict-aliasing is used
include/linux/slab.h:147:0: error: type of 'kmem_cache_destroy' does not match original declaration [-Werror=lto-type-mismatch]
void kmem_cache_destroy(struct kmem_cache *);
mm/slab_common.c:858:6: note: 'kmem_cache_destroy' was previously declared here
void kmem_cache_destroy(struct kmem_cache *s)
^
mm/slab_common.c:858:6: note: code may be misoptimized unless -fno-strict-aliasing is used
include/linux/slab.h:140:0: error: type of 'kmem_cache_create' does not match original declaration [-Werror=lto-type-mismatch]
struct kmem_cache *kmem_cache_create(const char *name, size_t size,
mm/slab_common.c:534:1: note: 'kmem_cache_create' was previously declared here
kmem_cache_create(const char *name, size_t size, size_t align,
^
This removes the header inclusion and instead uses the kmem_cache_size()
interface to get the size in a reliable way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It's expensive to set buffer flags that are already set, because that
causes a costly cache line transition.
A common case is setting the "verified" flag during ext4 writes.
This patch checks for the flag being set first.
With the AIM7/creat-clo benchmark testing on a 48G ramdisk based-on ext4
file system, we see 3.3%(15431->15936) improvement of aim7.jobs-per-min on
a 2-sockets broadwell platform.
What the benchmark does is: it forks 3000 processes, and each process do
the following:
a) open a new file
b) close the file
c) delete the file
until loop=100*1000 times.
The original patch is contributed by Andi Kleen.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Kemi Wang <kemi.wang@intel.com>
Signed-off-by: Kemi Wang <kemi.wang@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
[dwmw2: Use ARRAY_SIZE]
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1517484441-1420-3-git-send-email-dwmw@amazon.co.uk
|
|
There's no point in building init code with retpolines, since it runs before
any potentially hostile userspace does. And before the retpoline is actually
ALTERNATIVEd into place, for much of it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: karahmed@amazon.de
Cc: peterz@infradead.org
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1517484441-1420-2-git-send-email-dwmw@amazon.co.uk
|
|
The added documentation explains how generated codes may differ
between clang bpf target and default target, and when to use
each target.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Intermittently security.ima is not being written for new files. This
patch re-initializes the new slab iint->atomic_flags field before
freeing it.
Fixes: commit 0d73a55208e9 ("ima: re-introduce own integrity cache lock")
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Adding James Bottomley as the new maintainer for trusted keys.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
The arbitrary 4MB minimum namespace size turns out to be too large for
some environments. Quoting Cheng-mean Liu:
In the case of emulated NVDIMM devices in the VM environment, there
are scenarios that NVDIMM device with much smaller sizes are
desired, for example, we might use a single enumerated NVDIMM DAX
device for representing each container layer, which in some cases
could be just a few KBs size.
PAGE_SIZE is the minimum where we can still support DAX of at least
a single page.
Cc: Matthew Wilcox <willy@infradead.org>
Reported-by: Cheng-mean Liu <soccerl@microsoft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
gcc thinks that interpreting a multiplication result as a bool
is confusing:
drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c: In function 'read_pll':
drivers/gpu/drm/nouveau/nvkm/subdev/clk/gt215.c:133:8: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
Adding a temporary variable to contain the divisor helps make
it clear what is going on and avoids that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This adds the NvPmEnableGating config option to nouveau, which can be
used to enable or disable clockgating for supported chipsets. Enabling
can be done by passing
config=NvPmEnableGating=1
To nouveau. If your chipset supports it, you'll see a message in your
kernel log indicating that clockgating is enabled. Since clockgating has
only had limited testing thus far, we leave this option disabled by
default for now.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
That's right, there's still more power saving to go! Starting with
kepler 2, nvidia hardware has an additional level of clockgating known
as second level clockgating. The details of this are not exact, but it
seems to work by waiting for a collection of dependent hardware blocks
to be gated before taking affect. As with the previous series, this
results in another noticeable drop in power consumption and is
programmed in the same manner.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Same as the previous patch, but for Kepler2 now
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This enables BLCG optimization for kepler1. When using clockgating,
nvidia's firmware has a set of registers which are initially programmed
by the vbios with various engine delays and other mysterious settings
that are safe enough to bring up the GPU. However, the values used by
the vbios are more power hungry then they need to be, so the nvidia driver
writes it's own more optimized set of BLCG settings before enabling
CG_CTRL. This adds support for programming the optimized BLCG values
during engine/subdev init, which enables rather significant power
savings.
This introduces the nvkm_therm_clkgate_init() helper, which we use to
program the optimized BLCG settings before enabling clockgating with
nvkm_therm_clkgate_enable.
As well, this commit shares a lot more code with Fermi since BLCG is
mostly the same there as far as we can tell. In the future, it's likely
we'll reformat the clkgate_packs for kepler1 so that they share a list
of mmio packs with Fermi.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This adds support for enabling automatic clockgating on nvidia GPUs for
Kepler1. While this is not technically a clockgating level, it does
enable clockgating using the clockgating values initially set by the
vbios (which should be safe to use).
This introduces two therm helpers for controlling basic clockgating:
nvkm_therm_clkgate_enable() - enables clockgating through
CG_CTRL, done after initializing the GPU fully
nvkm_therm_clkgate_fini() - prepares clockgating for suspend or
driver unload
A lot of this code was originally going to be based off of fermi;
however it turns out that while Fermi's the first line of GPUs that
introduced this kind of power saving, Fermi requires more fine tuned
control of the CG_CTRL registers from the driver while reclocking that
we don't entirely understand yet.
For the simple parts we will be sharing with Fermi for certain however,
we at least add those into a new subdev/therm/gf100.h header.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
We've still been directly using the legacy crtc gamma_set() hook even
after conversion to atomic modesetting.
For userspace clients this was fine, however, fbcon will use the atomic
property when it's running on an atomic driver, which means we miss its
colormap updates - which is particularly bad for 8bpp framebuffers!
This commit converts the driver to use the atomic property + the helper
function implementing the legacy hook on top of atomic.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
For some reason forgotten by history, we've been using a 1025-entry LUT
mode, and sparsely filling it with the 256-entry LUT we're handed.
Until we land support for the full atomic colour management properties,
this commit switches to using the 257-entry mode to fix colour mapping
with depth 30 framebuffers.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This is what was done prior to the big refactor in kernel 3.8, and what
was done by xf86-video-nv. Experimentally, it seems like there's some
sort of issue with the high-res lut to be used there. Tested on G92.
This ends up mattering because fbcon/fbdev chooses the C8 fb format for
low-vram systems, which can occur with some IGP-based configurations
with little "stolen" vram.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
We need to double-buffer LUTs to handle their update atomically.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This is a common, awkward sequence. Let's wrap it up!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Useful for debugging.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
|
|
It's entirely possibly that the other r375 code is relevant to r370 too,
but I've not confirmed this, so I'll leave it where it is for now.
NVIDIA's copyright headers maintained, as it's still all their code.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
|
|
gcc-8 reports
drivers/gpu/drm/nouveau/nvkm/engine/pm/base.c: In function 'nvkm_perfmon_mthd':
include/linux/string.h:265:9: error: '__builtin_strncpy' specified bound 64 equals destination size [-Werror=stringop-truncation]
We need one less byte or call strlcpy() to make it a
nul-terminated string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The kbuild test bot complained about a new coccinelle warning nearby,
which sparked a discussion about the assignment to 'memory' inside of
the conditional expression. See Link below for the original post.
Fix the assignment to silence the coccinelle warning and also make the
code look a little nicer.
Link: https://lists.freedesktop.org/archives/nouveau/2017-November/029242.html
Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
|
|
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Reverse mapping has had a while to soak, so remove the experimental tag.
Now that we've landed space metadata cross-referencing in scrub, the
feature actually has a purpose.
Reject rmap filesystems with an rt device until the code to support it
is actually implemented.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
|
|
We don't support realtime filesystems with reflink either, so fail
those mounts.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
|
