| Age | Commit message (Collapse) | Author |
|---|
|
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to respond
to the request causes failure to exit L1 PM Substate (Jianjun Wang)
* remotes/lorenzo/pci/mediatek-gen3:
PCI: mediatek-gen3: Disable DVFSRC voltage request
|
|
- Assert PERST# for 100ms to allow power and clock to stabilize (qizhong
cheng)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Assert PERST# for 100ms for power and clock to stabilize
|
|
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode DT
properties (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
PCI: keystone: Use phandle argument from "ti,syscon-pcie-id"/"ti,syscon-pcie-mode"
dt-bindings: PCI: ti,am65: Fix "ti,syscon-pcie-id"/"ti,syscon-pcie-mode" to take argument
|
|
- Add hv-internal interfaces to encapsulate arch IRQ dependencies (Sunil
Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
* pci/host/hv:
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
|
|
- Return failure from pci_epc_set_msi() if no interrupts are available (Li
Chen)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Return -EINVAL when interrupts num is smaller than 1
|
|
- Don't ioremap NULL when DT lacks ATU resource (Tim Harvey)
- Drop redundant qcom-ep error message for platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Add i.MX8MM support (Richard Zhu)
- Use DWC common ops instead of layerscape-specific link-up functions (Hou
Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: layerscape: Change to use the DWC common link-up check function
PCI: imx: Add the imx8mm pcie support
dt-bindings: imx6q-pcie: Add PHY phandles and name properties
PCI: qcom-ep: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Do not remap invalid res
|
|
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors and not
fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding (Jim
Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected devices
(Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is added or
removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup devices
(Jim Quinlan)
* pci/host/brcmstb:
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
|
|
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
* remotes/lorenzo/pci/apple:
PCI: apple: Fix REFCLK1 enable/poll logic
PCI: apple: Enable clock gating
|
|
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2, DEVSTA2,
LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2 registers
(Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali Rohár)
- Mask all interrupts when unbinding host controller driver (Pali Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali Rohár)
- Disable common PHY when unbinding host controller driver (Pali Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix checking for MEM resource type
PCI: aardvark: Disable common PHY when unbinding driver
PCI: aardvark: Disable link training when unbinding driver
PCI: aardvark: Assert PERST# when unbinding driver
PCI: aardvark: Fix memory leak in driver unbind
PCI: aardvark: Mask all interrupts when unbinding driver
PCI: aardvark: Disable bus mastering when unbinding driver
PCI: aardvark: Comment actions in driver remove method
PCI: aardvark: Clear all MSIs at setup
PCI: aardvark: Add support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2 registers on emulated bridge
PCI: pci-bridge-emul: Add definitions for missing capabilities registers
PCI: pci-bridge-emul: Add description for class_revision field
|
|
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller so it
can work with an IOMMU (Yifeng Li)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
|
|
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and initialized for
every call (Kelvin Cao)
* pci/switchtec:
PCI/switchtec: Declare local state_names[] as static
PCI/switchtec: Add Gen4 automotive device IDs
|
|
- Always write Intel I210 ROM BAR on update to work around device defect
(Bjorn Helgaas)
* pci/resource:
PCI: Work around Intel I210 ROM BAR overlap defect
|
|
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
- Optimize by using percpu_ref_tryget_live_rcu() inside RCU critical
section (Christophe JAILLET)
* pci/p2pdma:
PCI/P2PDMA: Use percpu_ref_tryget_live_rcu() inside RCU critical section
MAINTAINERS: Add Logan Gunthorpe as P2PDMA maintainer
|
|
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power management to
generic power management (Vaibhav Gupta)
* pci/legacy-pm-removal:
via-agp: convert to generic power management
sis-agp: convert to generic power management
amd64-agp: convert to generic power management
|
|
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas Wunner)
- Removed commented-out ibmphp functions (Vihas Mak)
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
* pci/hotplug:
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
PCI: ibmphp: Remove commented-out functions
PCI: pciehp: Fix infinite loop in IRQ handler upon power fault
|
|
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups (Greg
Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum (Rajat
Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
* pci/enumeration:
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
PCI/sysfs: Use default_groups in kobj_type for slot attrs
PCI: Convert pci_dev_present() stub to static inline
PCI: Use pci_find_vsec_capability() when looking for TBT devices
|
|
- Calculate link L0s and L1 exit latencies when needed instead of caching
them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed instead
of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
* pci/aspm:
PCI/ASPM: Remove struct aspm_latency
PCI/ASPM: Stop caching device L0s, L1 acceptable exit latencies
PCI/ASPM: Stop caching link L0s, L1 exit latencies
PCI/ASPM: Move pci_function_0() upward
|
|
There is a spelling mistake in a pr_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
To pick the changes from:
d341db8f48ea4331 ("x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature flag")
This only causes these perf files to be rebuilt:
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o
And addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Cc: Huang Rui <ray.huang@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Picking the changes from:
43d5ac7d07023cd1 ("drm: document DRM_IOCTL_MODE_GETFB2")
It is just a comment, so no changes and silences these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
mem memcpy'
To bring in the change made in this cset:
f94909ceb1ed4bfd ("x86: Prepare asm files for straight-line-speculation")
It silences these perf tools build warnings, no change in the tools:
Warning: Kernel ABI header at 'tools/arch/x86/lib/memcpy_64.S' differs from latest version at 'arch/x86/lib/memcpy_64.S'
diff -u tools/arch/x86/lib/memcpy_64.S arch/x86/lib/memcpy_64.S
Warning: Kernel ABI header at 'tools/arch/x86/lib/memset_64.S' differs from latest version at 'arch/x86/lib/memset_64.S'
diff -u tools/arch/x86/lib/memset_64.S arch/x86/lib/memset_64.S
The code generated was checked before and after using 'objdump -d /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o',
no changes.
Cc: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick up fixes and get in line with other trees, powerpc kernel
mostly this time, but BPF as well.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
We encountered some crashes caused by the race between SMC-R
link access and link clear that triggered by abnormal link
group termination, such as port error.
Here is an example of this kind of crashes:
BUG: kernel NULL pointer dereference, address: 0000000000000000
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_llc_flow_initiate+0x44/0x190 [smc]
Call Trace:
<TASK>
? __smc_buf_create+0x75a/0x950 [smc]
smcr_lgr_reg_rmbs+0x2a/0xbf [smc]
smc_listen_work+0xf72/0x1230 [smc]
? process_one_work+0x25c/0x600
process_one_work+0x25c/0x600
worker_thread+0x4f/0x3a0
? process_one_work+0x600/0x600
kthread+0x15d/0x1a0
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
smc_listen_work() __smc_lgr_terminate()
---------------------------------------------------------------
| smc_lgr_free()
| |- smcr_link_clear()
| |- memset(lnk, 0)
smc_listen_rdma_reg() |
|- smcr_lgr_reg_rmbs() |
|- smc_llc_flow_initiate() |
|- access lnk->lgr (panic) |
These crashes are similarly caused by clearing SMC-R link
resources when some functions is still accessing to them.
This patch tries to fix the issue by introducing reference
count of SMC-R links and ensuring that the sensitive resources
of links won't be cleared until reference count reaches zero.
The operation to the SMC-R link reference count can be concluded
as follows:
object [hold or initialized as 1] [put]
--------------------------------------------------------------------
links smcr_link_init() smcr_link_clear()
connections smc_conn_create() smc_conn_free()
Through this way, the clear of SMC-R links is later than the
free of all the smc connections above it, thus avoiding the
unsafe reference to SMC-R links.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is no longer suitable to identify whether a smc connection
is registered in a link group through checking if conn->lgr
is NULL, because conn->lgr won't be reset even the connection
is unregistered from a link group.
So this patch introduces a new helper smc_conn_lgr_valid() and
replaces all the check of conn->lgr in original implementation
with the new helper to judge if conn->lgr is valid to use.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both fields can be read/written without synchronization,
add proper accessors and documentation.
Fixes: d5dd88794a13 ("inet: fix various use-after-free in defrags units")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wen Gu says:
====================
net/smc: Fixes for race in smc link group termination
We encountered some crashes recently and they are caused by the
race between the access and free of link/link group in abnormal
smc link group termination. The crashes can be reproduced in
frequent abnormal link group termination, like setting RNICs up/down.
This set of patches tries to fix this by extending the life cycle
of link/link group to ensure that they won't be referred to after
cleared or freed.
v1 -> v2:
- Improve some comments.
- Move codes of waking up lgrs_deleted wait queue from smc_lgr_free()
to __smc_lgr_free().
- Move codes of waking up links_deleted wait queue from smcr_link_clear()
to __smcr_link_clear().
- Move codes of smc_ibdev_cnt_dec() and put_device() from smcr_link_clear()
to __smcr_link_clear()
- Move smc_lgr_put() to the end of __smcr_link_clear().
- Call smc_lgr_put() after 'out' tag in smcr_link_init() when link
initialization fails.
- Modify the location where smc connection holds the lgr or link.
before:
* hold lgr in smc_lgr_register_conn().
* hold link in smcr_lgr_conn_assign_link().
after:
* hold both lgr and link in smc_conn_create().
Modify the location to symmetrical with the place where smc connections
put the lgr or link, which is smc_conn_free().
- Initialize conn->freed as zero in smc_conn_create().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We encountered some crashes caused by the race between the access
and the termination of link groups.
Here are some of panic stacks we met:
1) Race between smc_clc_wait_msg() and __smc_lgr_terminate()
BUG: kernel NULL pointer dereference, address: 00000000000002f0
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_clc_wait_msg+0x3eb/0x5c0 [smc]
Call Trace:
<TASK>
? smc_clc_send_accept+0x45/0xa0 [smc]
? smc_clc_send_accept+0x45/0xa0 [smc]
smc_listen_work+0x783/0x1220 [smc]
? finish_task_switch+0xc4/0x2e0
? process_one_work+0x1ad/0x3c0
process_one_work+0x1ad/0x3c0
worker_thread+0x4c/0x390
? rescuer_thread+0x320/0x320
kthread+0x149/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
smc_listen_work() abnormal case like port error
---------------------------------------------------------------
| __smc_lgr_terminate()
| |- smc_conn_kill()
| |- smc_lgr_unregister_conn()
| |- set conn->lgr = NULL
smc_clc_wait_msg() |
|- access conn->lgr (panic) |
2) Race between smc_setsockopt() and __smc_lgr_terminate()
BUG: kernel NULL pointer dereference, address: 00000000000002e8
RIP: 0010:smc_setsockopt+0x17a/0x280 [smc]
Call Trace:
<TASK>
__sys_setsockopt+0xfc/0x190
__x64_sys_setsockopt+0x20/0x30
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
smc_setsockopt() abnormal case like port error
--------------------------------------------------------------
| __smc_lgr_terminate()
| |- smc_conn_kill()
| |- smc_lgr_unregister_conn()
| |- set conn->lgr = NULL
mod_delayed_work() |
|- access conn->lgr (panic) |
There are some other panic places and they are caused by the
similar reason as described above, which is accessing link
group after termination, thus getting a NULL pointer or invalid
resource.
Currently, there seems to be no synchronization between the
link group access and a sudden termination of it. This patch
tries to fix this by introducing reference count of link group
and not freeing link group until reference count is zero.
Link group might be referred to by links or smc connections. So
the operation to the link group reference count can be concluded
as follows:
object [hold or initialized as 1] [put]
-------------------------------------------------------------------
link group smc_lgr_create() smc_lgr_free()
connections smc_conn_create() smc_conn_free()
links smcr_link_init() smcr_link_clear()
Througth this way, we extend the life cycle of link group and
ensure it is longer than the life cycle of connections and links
above it, so that avoid invalid access to link group after its
termination.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
timeout in settings is used by each case under the same directory, so
it should adapt to the maximum runtime.
A normally running net/fib_nexthops.sh may be killed by this unsuitable
timeout. Furthermore, since the defect[1] of kselftests framework,
net/fib_nexthops.sh which might take at least (300 * 4) seconds would
block the whole kselftests framework previously.
$ git grep -w 'sleep 300' tools/testing/selftests/net
tools/testing/selftests/net/fib_nexthops.sh: sleep 300
tools/testing/selftests/net/fib_nexthops.sh: sleep 300
tools/testing/selftests/net/fib_nexthops.sh: sleep 300
tools/testing/selftests/net/fib_nexthops.sh: sleep 300
Enlarge the timeout by plus 300 based on the obvious largest runtime
to avoid the blocking.
[1]: https://www.spinics.net/lists/kernel/msg4185370.html
Signed-off-by: Zhou Jie <zhoujie2011@fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit b39648079db4 ("net: mscc: ocelot: disable flow control on
NPI interface"), flow control should be disabled on the DSA CPU port
when used in NPI mode.
However, the commit blamed in the Fixes: tag below broke this, because
it allowed felix_phylink_mac_link_up() to overwrite SYS_PAUSE_CFG_PAUSE_ENA
for the DSA CPU port.
This issue became noticeable since the device tree update from commit
8fcea7be5736 ("arm64: dts: ls1028a: mark internal links between Felix
and ENETC as capable of flow control").
The solution is to check whether this is the currently configured NPI
port from ocelot_phylink_mac_link_up(), and to not modify the statically
disabled PAUSE frame transmission if it is.
When the port is configured for lossless mode as opposed to tail drop
mode, but the link partner (DSA master) doesn't observe the transmitted
PAUSE frames, the switch termination throughput is much worse, as can be
seen below.
Before:
root@debian:~# iperf3 -c 192.168.100.2
Connecting to host 192.168.100.2, port 5201
[ 5] local 192.168.100.1 port 37504 connected to 192.168.100.2 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 28.4 MBytes 238 Mbits/sec 357 22.6 KBytes
[ 5] 1.00-2.00 sec 33.6 MBytes 282 Mbits/sec 426 19.8 KBytes
[ 5] 2.00-3.00 sec 34.0 MBytes 285 Mbits/sec 343 21.2 KBytes
[ 5] 3.00-4.00 sec 32.9 MBytes 276 Mbits/sec 354 22.6 KBytes
[ 5] 4.00-5.00 sec 32.3 MBytes 271 Mbits/sec 297 18.4 KBytes
^C[ 5] 5.00-5.06 sec 2.05 MBytes 270 Mbits/sec 45 19.8 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.06 sec 163 MBytes 271 Mbits/sec 1822 sender
[ 5] 0.00-5.06 sec 0.00 Bytes 0.00 bits/sec receiver
After:
root@debian:~# iperf3 -c 192.168.100.2
Connecting to host 192.168.100.2, port 5201
[ 5] local 192.168.100.1 port 49470 connected to 192.168.100.2 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 112 MBytes 941 Mbits/sec 259 143 KBytes
[ 5] 1.00-2.00 sec 110 MBytes 920 Mbits/sec 329 144 KBytes
[ 5] 2.00-3.00 sec 112 MBytes 936 Mbits/sec 255 144 KBytes
[ 5] 3.00-4.00 sec 110 MBytes 927 Mbits/sec 355 105 KBytes
[ 5] 4.00-5.00 sec 110 MBytes 926 Mbits/sec 350 156 KBytes
[ 5] 5.00-6.00 sec 110 MBytes 925 Mbits/sec 305 148 KBytes
[ 5] 6.00-7.00 sec 110 MBytes 924 Mbits/sec 320 143 KBytes
[ 5] 7.00-8.00 sec 110 MBytes 925 Mbits/sec 273 97.6 KBytes
[ 5] 8.00-9.00 sec 109 MBytes 913 Mbits/sec 299 141 KBytes
[ 5] 9.00-10.00 sec 110 MBytes 922 Mbits/sec 287 146 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.08 GBytes 926 Mbits/sec 3032 sender
[ 5] 0.00-10.00 sec 1.08 GBytes 925 Mbits/sec receiver
Fixes: de274be32cb2 ("net: dsa: felix: set TX flow control according to the phylink_mac_link_up resolution")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointer skb is redundant, it is assigned a value that is never
read and hence can be removed. Cleans up clang scan warning:
drivers/atm/iphase.c:205:18: warning: Although the value stored
to 'skb' is used in the enclosing expression, the value is never
actually read from 'skb' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The uapi headers are missing the ceph definition. Move it there so
userland apps can ID cephfs.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
The newcaps has already included the Ls, no need to check it again.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
CephFS is a bit unlike most other filesystems in that it only
conditionally does buffered I/O based on the caps that it gets from the
MDS. In most cases, unless there is contended access for an inode the
MDS does give Fbc caps to the client, so the unbuffered codepaths are
only infrequently traveled and are difficult to test.
At one time, the "-o sync" mount option would give you this behavior,
but that was removed in commit 7ab9b3807097 ("ceph: Don't use
ceph-sync-mode for synchronous-fs.").
Add a new mount option to tell the client to ignore Fbc caps when doing
I/O, and to use the synchronous codepaths exclusively, even on
non-O_DIRECT file descriptors. We already have an ioctl that forces this
behavior on a per-file basis, so we can just always set the CEPH_F_SYNC
flag in the file description on such mounts.
Additionally, this patch also changes the client to not request Fbc when
doing direct I/O. We aren't using the cache with O_DIRECT so we don't
have any need for those caps.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Acked-by: Greg Farnum <gfarnum@redhat.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
玮文 胡 reported seeing the WARN_RATELIMIT pop when writing to an
inode that had been transplanted into the stray dir. The client was
trying to look up the quotarealm info from the parent and that tripped
the warning.
Change the ceph_vino_is_reserved helper to not throw a warning for
MDS stray directories (0x100 - 0x1ff), only for reserved dirs that
are not in that range.
Also, fix ceph_has_realms_with_quotas to return false when encountering
a reserved inode.
URL: https://tracker.ceph.com/issues/53180
Reported-by: Hu Weiwen <sehuww@mail.scut.edu.cn>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
This pops every second and isn't very useful.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Don't populate the const array spaces on the stack but make it static
const and make the pointer an array to remove a dereference. Shrinks
object code a little too. Also clean up intent, currently it is spaces
and should be a tab.
Signed-off-by: Colin Ian King <colin.i.king@googlemail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Problem:
The statfs reports incorrect free/available space for quota less then
CEPH_BLOCK size (4M).
Solution:
For quota less than CEPH_BLOCK size, smaller block size of 4K is used.
But if quota is less than 4K, it is decided to go with binary use/free
of 4K block. For quota size less than 4K size, report the
total=used=4K,free=0 when quota is full and total=free=4K,used=0
otherwise.
Signed-off-by: Kotresh HR <khiremat@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Add read-only module parameters for supported mount syntaxes. Primary
user is the user-space mount helper for catching v2 syntax bugs during
testing by cross verifying if the kernel supports v2 syntax on mount
failure.
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Note that the new monitors are just shown in /proc/mounts.
Ceph does not (re)connect to new monitors yet.
[ jlayton: s/printk\(KERN_NOTICE/pr_notice(/
s/strcmp/strcmp_null/ ]
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Old mount device syntax (source) has the following problems:
- mounts to the same cluster but with different fsnames
and/or creds have identical device string which can
confuse xfstests.
- Userspace mount helper tool resolves monitor addresses
and fill in mon addrs automatically, but that means the
device shown in /proc/mounts is different than what was
used for mounting.
New device syntax is as follows:
cephuser@fsid.mycephfs2=/path
Note, there is no "monitor address" in the device string.
That gets passed in as mount option. This keeps the device
string same when monitor addresses change (on remounts).
Also note that the userspace mount helper tool is backward
compatible. I.e., the mount helper will fallback to using
old syntax after trying to mount with the new syntax.
[ idryomov: drop CEPH_MON_ADDR_MNTOPT_DELIM ]
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
... as it is too generic. also, use __func__ when logging
rather than hardcoding the function name.
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
... and remove hardcoded function name in ceph_parse_ips().
[ idryomov: delim parameter, drop CEPH_ADDR_PARSE_DEFAULT_DELIM ]
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
The attach callback of struct Qdisc_ops is used by only a few qdiscs:
mq, mqprio and htb. qdisc_graft() contains the following logic
(pseudocode):
if (!qdisc->ops->attach) {
if (ingress)
do ingress stuff;
else
do egress stuff;
}
if (!ingress) {
...
if (qdisc->ops->attach)
qdisc->ops->attach(qdisc);
} else {
...
}
As we see, the attach callback is not called if the qdisc is being
attached to ingress (TC_H_INGRESS). That wasn't a problem for mq and
mqprio, since they contain a check that they are attached to TC_H_ROOT,
and they can't be attached to TC_H_INGRESS anyway.
However, the commit cited below added the attach callback to htb. It is
needed for the hardware offload, but in the non-offload mode it
simulates the "do egress stuff" part of the pseudocode above. The
problem is that when htb is attached to ingress, neither "do ingress
stuff" nor attach() is called. It results in an inconsistency, and the
following message is printed to dmesg:
unregister_netdevice: waiting for lo to become free. Usage count = 2
This commit addresses the issue by running "do ingress stuff" in the
ingress flow even in the attach callback is present, which is fine,
because attach isn't going to be called afterwards.
The bug was found by syzbot and reported by Eric.
Fixes: d03b195b5aa0 ("sch_htb: Hierarchical QoS hardware offload")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modem from ZTE MF286D is an Qualcomm MDM9250 based 3G/4G modem.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=19d2 ProdID=1485 Rev=52.87
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE Technologies MSM
S: SerialNumber=MF286DZTED000000
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Entries without dmi_table nor codec_hid field need to be placed after
entries with these two fields or they will be always selected.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/20220113105220.1114694-3-brent.lu@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add rules to select SOF driver for Jasper Lake systems if digital
microphone is present or the system is a Chromebook.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/20220113105220.1114694-2-brent.lu@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix cma_heap_buffer mutex locking critical section to protect vmap_cnt
and vaddr.
Fixes: a5d2d29e24be ("dma-buf: heaps: Move heap-helper logic into the cma_heap implementation")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220104073545.124244-1-o451686892@gmail.com
|
|
Add the visible flag to the toc_stack variable to make it visible for
assembly code and to avoid a sparse warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Clang static analysis reports this problem
dw-i3c-master.c:799:9: warning: The result of the left shift is
undefined because the left operand is negative
COMMAND_PORT_DEV_INDEX(pos) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~
pos can be negative because dw_i3c_master_get_free_pos() can return an
error. So check for an error.
Fixes: 1dd728f5d4d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220108150948.3988790-1-trix@redhat.com
|
