| Age | Commit message (Collapse) | Author |
|---|
|
Pull drm regression fix from Dave Airlie:
"This one fixes a sleep while locked regression that was introduced
earlier in 3.8."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try
|
|
In wl18xx, we use a new ACX command in order to set the remote
supported rates, once we know it (ie. after association). The wl12xx
firmware doesn't support changing the rates after the STA is started,
so we need to use all supported rates.
Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using
wlvif->rate_set when starting the STA role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Add back-off settings to the wl18xx_mac_and_phy_params. We had an
empty space where the new parameters are added, so this change doesn't
affect backwards-compatibility with older firmwares.
Update WL18XX_CONF_VERSION accordingly.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
There's no need to hide the actual error that was reported when
booting fails. For instance, on I/O error, we were returing
-EINVALID, which doesn't make sense at all.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The platform data is used not only by wlcore-based drivers, but also
by wl1251. Move it up in the directory hierarchy to reflect this.
Additionally, make it truly optional. At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
The platform devices can be created by both wlcore_sdio and
wlcore_spi. Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We can't pass pointers from the platform data to the modules, because
with DT it cannot be done. Those pointers are not set by the board
files anyway. It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.
Create a new structure that the bus modules pass to wlcore. This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
There is no platform-specific set_power method anymore. Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.
Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version. Fix this by using the
single-role version for everything except multi-role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In commit 6509141f9c2ba74df6cc72ec35cd1865276ae3a4 ("usbnet: add new
flag FLAG_NOARP for usb net devices"), the newly added flag NOARP was
using an already defined value, which broke drivers using flag
MULTI_PACKET.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew Savchenko reported a DNS failure and we diagnosed that
some UDP sockets were unable to send more packets because their
sk_wmem_alloc was corrupted after a while (tx_queue column in
following trace)
$ cat /proc/net/udp
sl local_address rem_address st tx_queue rx_queue tr tm->when retrnsmt uid timeout inode ref pointer drops
...
459: 00000000:0270 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4507 2 ffff88003d612380 0
466: 00000000:0277 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4802 2 ffff88003d613180 0
470: 076A070A:007B 00000000:0000 07 FFFF4600:00000000 00:00000000 00000000 123 0 5552 2 ffff880039974380 0
470: 010213AC:007B 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4986 2 ffff88003dbd3180 0
470: 010013AC:007B 00000000:0000 07 00000000:00000000 00:00000000 00000000 0 0 4985 2 ffff88003dbd2e00 0
470: 00FCA8C0:007B 00000000:0000 07 FFFFFB00:00000000 00:00000000 00000000 0 0 4984 2 ffff88003dbd2a80 0
...
Playing with skb->truesize is tricky, especially when
skb is attached to a socket, as we can fool memory charging.
Just remove this code, its not worth trying to be ultra
precise in xmit path.
Reported-by: Andrew Savchenko <bircoph@gmail.com>
Tested-by: Andrew Savchenko <bircoph@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Attention linux-next maintainer, you will hit a merge conflict between
this merge and the mips tree, the resolution is to preserve the removal
of uses of nvram_geenv() and nvram_parse_macaddr() from the net-next
side.
Hauke Mehrtens says:
====================
These patches are adding support for the Ethernet core found in the
BCM4705/BCM4785 SoC.
This is based on current master of davem/net-next.git.
v4:
* move setting of DMA_RWCTRL_ONE_DMA
v3:
* combined first two patches into one patch
v2:
* use of struct sprom in ssb_gige_get_macaddr() instead of accessing
the nvram directly
* add return value to ssb_gige_get_macaddr()
* try to read the mac address from ssb core before accessing the own
registers.
* fix two checkpatch warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM4785 or sometimes named BMC4705 is a Broadcom SoC which a
Gigabit 5750 Ethernet core. The core is connected via PCI with the rest
of the SoC, but it uses some extension.
This core does not use a firmware or an eeprom.
Some devices only have a switch which supports 100MBit/s, this
currently does not work with this driver.
This patch was original written by Michael Buesch <m@bues.ch> and is in
OpenWrt for some years now.
This was tested on a Linksys WRT610N V1 and older versions of this patch
were tested by other people on different devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In OpenWrt we currently use a switch driver which uses the ioctls to
configure the switch in the phy. We have to provide the phy_id to do
so, but without this patch this is not possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac address is already stored in the sprom structure by the
platform code of the SoC this Ethernet core is found on, it just has to
be fetched from this structure instead of accessing the nvram here.
This patch also adds a return value to indicate if a mac address could
be fetched from the sprom structure.
When CONFIG_SSB_DRIVER_GIGE is not set the header file now also declares
ssb_gige_get_macaddr().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of calling 3 times ntohs(random->param_hdr.length), 2 times
ntohs(hmacs->param_hdr.length), and 3 times ntohs(chunks->param_hdr.length)
within the same function, we only call each once and store it in a
variable.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For sensitive data like keying material, it is common practice to zero
out keys before returning the memory back to the allocator. Thus, use
kzfree instead of kfree.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch into openvswitch
Jesse Gross says:
====================
One bug fix for net/3.8 for a long standing problem that was reported a few
times recently.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.8.0-rc5+ #82 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&fep->hw_lock)->rlock){..-...}, at: [<8034e2f8>] fec_enet_start_xmit+0x48/0x 2cc
but this lock took another, SOFTIRQ-unsafe lock in the past:
(prepare_lock){+.+.+.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(prepare_lock);
local_irq_disable()
lock(&(&fep->hw_lock)->rlock);
lock(prepare_lock);
<Interrupt>
lock(&(&fep->hw_lock)->rlock);
*** DEADLOCK ***
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Old method will cause init spinlock twice.
New method will avoid init spinlock twice and fix miss init spinlock
at fec_restart.
BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
[<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
[<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
[<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
r5:805f6f8c r4:bfae0f8c
[<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0 )
r5:806b4950 r4:bfae0f8c
[<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs ave+0x18/0x20)
[<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_ cyclecounter+0x3c/0x120)
r4:bfae0f8c r3:00000002
[<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta rt+0x56c/0x5f8)
r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
[<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix issue in Mellanox driver related to BQL. netdev_tx_reset_queue
was not being called in certain situations where the device was
being start and stopped. Moved netdev_tx_reset_queue from the reset
device path to mlx4_en_free_tx_buf which is where the rings are
cleaned in a reset (specifically from device being stopped).
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ian Campbell says:
====================
The Xen netback implementation contains a couple of flaws which can
allow a guest to cause a DoS in the backend domain, potentially
affecting other domains in the system.
CVE-2013-0216 is a failure to sanity check the ring producer/consumer
pointers which can allow a guest to cause netback to loop for an
extended period preventing other work from occurring.
CVE-2013-0217 is a memory leak on an error path which is guest
triggerable.
The following series contains the fixes for these issues, as previously
included in Xen Security Advisory 39:
http://lists.xen.org/archives/html/xen-announce/2013-02/msg00001.html
Changes in v2:
- Typo and block comment format fixes
- Added stable Cc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A buggy or malicious frontend should not be able to confuse netback.
If we spot anything which is not as it should be then shutdown the
device and don't try to continue with the ring in a potentially
hostile state. Well behaved and non-hostile frontends will not be
penalised.
As well as making the existing checks for such errors fatal also add a
new check that ensures that there isn't an insane number of requests
on the ring (i.e. more than would fit in the ring). If the ring
contains garbage then previously is was possible to loop over this
insane number, getting an error each time and therefore not generating
any more pending requests and therefore not exiting the loop in
xen_netbk_tx_build_gops for an externded period.
Also turn various netdev_dbg calls which no precipitate a fatal error
into netdev_err, they are rate limited because the device is shutdown
afterwards.
This fixes at least one known DoS/softlockup of the backend domain.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
This series from Yan Burman adds support for unicast MAC address filtering and
ndo FDB operations. It also includes some optimizations to loopback related
decisions and checks in the TX/RX fast path and one cleanup, all in separate
patches.
Today, when adding macvlan devices, the NIC goes into promiscuous mode, since
unicast MAC filtering is not supported. With these changes, macvlan devices can
be added without the penalty of promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Also, now it is possible to have bridge under multi-function configuration that include
PF and VFs. In order to use bridge over PF/VFs, VM MAC fdb entries must be added e.g.
using 'bridge fdb add' command.
Changes from v1 - based on more comments from Eric Dumazet:
* added failure handling when adding unicast address filter
Changes from v0 - based on comments from Eric Dumazet:
* Removed unneeded synchronize_rcu()
* Use kfree_rcu() instead of synchronize_rcu() + kfree()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for setting embedded switch fdb in case of SRIOV, by
implementing ndo_fdb_{add, del, dump}. This will allow to use
bridged configuration with multi-function. In order to add VM MAC
to the eSwitch fdb, the following command may be used over the relevant function interface:
bridge fdb add <MAC> permanent self dev <IFACE>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement and advertise unicast MAC filtering, such that setting macvlan
instance over mlx4_en interfaces will not require the networking core
to put mlx4_en devices in promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation step for supporting multiple unicast addresses, store MAC addresses in hash table.
Remove the radix tree for MAC addresses per QP, as it's not in use.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to having more than one unicast MAC per port, we need to keep track
of the previous MAC address in the flow of ndo_set_mac_address,
so that mlx4_en_replace_mac will know what to replace.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, mlx4_en_do_set_multicast serves as the ndo_set_rx_mode entry for mlx4_en,
doing all related work. Split it to few calls, one per required functionality
(e.g multicast, promiscuous, etc) and rename some structures and calls
to use rx_mode notation instead of multicast.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.
Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp
To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the code consistent in regard to error messages
not spanning multiple lines.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, RX path code that does RX filtering is not optimized
and does an expensive conversion. In order to use ether_addr_equal_64bits
which is optimized for such cases, we need the MAC address kept by the device
to be in the form of unsigned char array instead of u64. Store the MAC address
as unsigned char array and convert to/from u64 out of the fast path when needed.
Side effect of this is that we no longer need priv->mac, since it's the same
as dev->dev_addr.
This optimization was suggested by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fix from Rusty Russell:
"Obviously I forgot to push this before linux.conf.au..."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_console: Don't access uninitialized data.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull IB regression fixes from Roland Dreier:
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix for broken sparse warning fix
mlx4_core: Fix advertisement of wrong PF context behaviour
IPoIB: Fix crash due to skb double destruct
|
|
defined(@array) is deprecated in Perl and gives off a warning.
Restructure the code to remove that warning.
[ hpa: it would be interesting to revert to the timeconst.bc script.
It appears that the failures reported by akpm during testing of
that script was due to a known broken version of make, not a problem
with bc. The Makefile rules could probably be restructured to avoid
the make bug, or it is probably old enough that it doesn't matter. ]
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've got corner cases for updating i_size that ceph was hitting,
error handling for quotas when we run out of space, a very subtle
snapshot deletion race, a crash while removing devices, and one
deadlock between subvolume creation and the sb_internal code (thanks
lockdep)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: move d_instantiate outside the transaction during mksubvol
Btrfs: fix EDQUOT handling in btrfs_delalloc_reserve_metadata
Btrfs: fix possible stale data exposure
Btrfs: fix missing i_size update
Btrfs: fix race between snapshot deletion and getting inode
Btrfs: fix missing release of the space/qgroup reservation in start_transaction()
Btrfs: fix wrong sync_writers decrement in btrfs_file_aio_write()
Btrfs: do not merge logged extents if we've removed them from the tree
btrfs: don't try to notify udev about missing devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull late pinctrl fixes from Linus Walleij:
"Two patches appeared as of late, one was completely news to me, the
other one was rotated in -next for the next merge window but turned
out to be a showstopper.
- Exynos Kconfig fixup
- SIRF DT translation bug"
* tag 'pinctrl-for-v3.8-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sirf: replace of_gpio_simple_xlate by sirf specific of_xlate
pinctrl: exynos: change PINCTRL_EXYNOS option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"This has two fixes. One is a security fix wherein we would spam the
kernel printk buffer if one of the guests was misbehaving. The other
is much tamer and it was us only checking for one type of error from
the IRQ subsystem (when allocating new IRQs) instead of for all of
them.
- Fix an IRQ allocation where we only check for a specific error (-1).
- CVE-2013-0231 / XSA-43. Make xen-pciback rate limit error messages
from xen_pcibk_enable_msi{,x}()"
* tag 'stable/for-linus-3.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: fix error handling path if xen_allocate_irq_dynamic fails
xen-pciback: rate limit error messages from xen_pcibk_enable_msi{,x}()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Mostly driver specific fixes here, though one of them uncovered the
issue Stephen Warren fixed with multiple OF matches getting upset due
to a lack of cleanup."
* tag 'regulator-v3.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: fix incorrect register for buck10
regulator: clear state each invocation of of_regulator_match
regulator: max8997: Fix using wrong dev argument at various places
regulator: max77686: Fix using wrong dev argument at various places
regulator: max8907: Fix using wrong dev argument for calling of_regulator_match
regulator: max8998: fix incorrect min_uV value for ldo10
regulator: tps65910: Fix using wrong dev argument for calling of_regulator_match
regulator: tps65217: Fix using wrong dev argument for calling of_regulator_match
|
|
This fixes up
commit e8e89622ed361c46bf90ba4828e685a8b603f7e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 18 22:25:11 2012 +0100
drm/ttm: fix fence locking in ttm_buffer_object_transfer
which leaves behind a might_sleep in atomic context, since the
fence_lock spinlock is held over a kmalloc(GFP_KERNEL) call. The fix
is to revert the above commit and only take the lock where we need it,
around the call to ->sync_obj_ref.
v2: Fixup things noticed by Maarten Lankhorst:
- Brown paper bag locking bug.
- No need for kzalloc if we clear the entire thing on the next line.
- check for bo->sync_obj (totally unlikely race, but still someone
else could have snuck in) and clear fbo->sync_obj if it's cleared
already.
Reported-by: Dave Airlie <airlied@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The old SRCU implementation loads sp->completed within an
RCU-sched section, courtesy of preempt_disable(). This was required
due to the use of synchronize_sched() in the old implemenation's
synchronize_srcu(). However, the new implementation does not rely
on synchronize_sched(), so it in turn does not require the load of
sp->completed and the ->c[] counter to be in a single preempt-disabled
region of code. This commit therefore moves the sp->completed access
outside of the preempt-disabled region and applies ACCESS_ONCE().
The resulting code is almost as the same as before, but it removes the
now-misleading rcu_dereference_index_check() call.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Because synchronize_srcu_expedited() no longer uses
synchronize_rcu_sched_expedited(), synchronize_srcu_expedited() no longer
indirectly acquires any CPU-hotplug-related locks. This commit therefore
updates the comments accordingly.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The core of SRCU is changed, but synchronize_srcu()'s comments describe
the old algorithm. This commit therefore updates them to match the
new algorithm.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
SRCU has its own statemachine and no longer relies on normal RCU.
Its read-side critical section can now be used by an offline CPU, so this
commit removes the check and the comments, reverting the SRCU portion
of ff195cb6 (rcu: Warn when srcu_read_lock() is used in an extended
quiescent state).
It also makes the codes match the comments in whatisRCU.txt:
g. Do you need read-side critical sections that are respected
even though they are in the middle of the idle loop, during
user-mode execution, or on an offlined CPU? If so, SRCU is the
only choice that will work for you.
[ paulmck: There is at least one remaining issue, namely use of lockdep
with tracing enabled. ]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
SRCU has its own statemachine and no longer relies on normal RCU.
Its read-side critical section can now be used by an offline CPU, so this
commit removes the check and the comments, reverting the SRCU portion
of c0d6d01b (rcu: Check for illegal use of RCU from offlined CPUs).
It also makes the code match the comments in whatisRCU.txt:
g. Do you need read-side critical sections that are respected
even though they are in the middle of the idle loop, during
user-mode execution, or on an offlined CPU? If so, SRCU is the
only choice that will work for you.
[ paulmck: There is at least one remaining issue, namely use of lockdep
with tracing enabled. ]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
