| Age | Commit message (Collapse) | Author |
|---|
|
'asoc/fix/sti' into asoc-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-04-25
this is a pull request of three patches for net/master.
There are two patches by Stephane Grosjean for that add a new variant to the
PCAN-Chip USB driver. The other patch is by Maksim Salau, which swtiches the
memory for USB transfers from heap to stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: dd248f1bc65b ("sfc: Add PCI ID for Solarflare 8000 series 10/40G NIC")
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY. Drop these
superfluous flags for fixing the behavior.
Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:
BUG: scheduling while atomic: systemd-sleep/3144/0x00000003
Call Trace:
dump_stack+0x5c/0x7a
__schedule_bug+0x55/0x70
__schedule+0x63c/0x8c0
schedule+0x3d/0x90
schedule_timeout+0x16b/0x320
? del_timer_sync+0x50/0x50
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? remove_wait_queue+0x60/0x60
? sst_prepare_and_post_msg+0x275/0x960 [snd_intel_sst_core]
? sst_pause_stream+0x9b/0x110 [snd_intel_sst_core]
....
This patch addresses these appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.1+
|
|
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb48c ("macvlan: Fix potential use-after free for...")
Reported-by: Joe Ghalam <Joe.Ghalam@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the PL-27A1 by adding the appropriate
USB ID's. This chip is used in the goobay Active USB 3.0 Data Link
and Unitek Y-3501 cables.
Signed-off-by: Roman Spychała <roed@onet.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a text line in the help section of the CAN_PEAK_USB
config item describing the support of the PCAN-USB X6 adapter, which is
already included in the Kernel since 4.9.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds the support of the PCAN-Chip USB, a stamp module for
customer hardware designs, which communicates via USB 2.0 with the
hardware. The integrated CAN controller supports the protocols CAN 2.0 A/B
as well as CAN FD. The physical CAN connection is determined by external
wiring. The Stamp module with its single-sided mounting and plated
half-holes is suitable for automatic assembly.
Note that the chip is equipped with the same logic than the PCAN-USB FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 97b50a654d5d ("virtio_blk: make SCSI passthrough support configurable")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We're probably going to be stuck quirking APST off on an over-broad
range of devices for 4.11. Let's make it easy to override the quirk
for testing.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Debugging APST is currently a bit of a pain. This gives optional
simple log messages that describe the APST state.
The easiest way to use this is probably with the nvme_core.dyndbg=+p
module parameter.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
There was a typo in the description of the timeout heuristic.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
Clevo P650RS and other similar devices require i8042 to be reset in order
to detect Synaptics touchpad.
Reported-by: Paweł Bylica <chfast@gmail.com>
Tested-by: Ed Bordin <edbordin@gmail.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=190301
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Florian Fainelli says:
====================
net: dsa: b53: BCM58xx devices fixes
This patch series contains fixes for the 58xx devices (Broadcom Northstar
Plus), which were identified thanks to the help of Eric Anholt.
====================
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb4645 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the correct software reset sequence for 58xx devices by
setting all 3 reset bits and polling for the SW_RST bit to clear itself
without a given timeout. We cannot use is58xx() here because that would
also include the 7445/7278 Starfighter 2 which have their own driver
doing the reset earlier on due to the HW specific integration.
Fixes: 991a36bb4645 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Broadcom tags are not enabled in b53 (DSA_PROTO_TAG_NONE), we need
to make sure that the IMP/CPU port is included in the forwarding
decision.
Without this change, switching between non-management ports would work,
but not between management ports and non-management ports thus breaking
the default state in which DSA switch are brought up.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Our final fix before the 4.12 release (hopefully).
It's an error leg again: the fix to not bug on empty DMA transfers is
returning the wrong code and confusing the block layer"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: return correct blkprep status code in case scsi_init_io() fails.
|
|
Pull MIPS fixes from Ralf Baechle:
"Another round of 4.11 for the MIPS architecture. This time around it's
mostly arch but little platforms-specific code.
- PCI: Register controllers in the right order to aoid a PCI error
- KGDB: Use kernel context for sleeping threads
- smp-cps: Fix potentially uninitialised value of core
- KASLR: Fix build
- ELF: Fix BUG() warning in arch_check_elf
- Fix modversioning of _mcount symbol
- fix out-of-tree defconfig target builds
- cevt-r4k: Fix out-of-bounds array access
- perf: fix deadlock
- Malta: Fix i8259 irqchip setup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: PCI: add controllers before the specified head
MIPS: KGDB: Use kernel context for sleeping threads
MIPS: smp-cps: Fix potentially uninitialised value of core
MIPS: KASLR: Add missing header files
MIPS: Avoid BUG warning in arch_check_elf
MIPS: Fix modversioning of _mcount symbol
MIPS: generic: fix out-of-tree defconfig target builds
MIPS: cevt-r4k: Fix out-of-bounds array access
MIPS: perf: fix deadlock
MIPS: Malta: Fix i8259 irqchip setup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-04-22
This series contains some mlx5 fixes for net.
For your convenience, the series doesn't introduce any conflict with
the ongoing net-next pull request.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: E-Switch, Correctly deal with inline mode on ConnectX-5") kernels >= 4.10
("net/mlx5e: Fix ETHTOOL_GRXCLSRLALL handling") kernels >= 4.8
("net/mlx5e: Fix small packet threshold") kernels >= 4.7
("net/mlx5: Fix driver load bad flow when having fw initializing timeout") kernels >= 4.4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When arp_notify is set to 1 for either a specific interface or for 'all'
interfaces, gratuitous arp requests are sent. Since ndisc_notify is the
ipv6 equivalent to arp_notify, it should follow the same semantics.
Commit 4a6e3c5def13 ("net: ipv6: send unsolicited NA on admin up") sends
the NA on admin up. The final piece is checking devconf_all->ndisc_notify
in addition to the per device setting. Add it.
Fixes: 5cb04436eef6 ("ipv6: add knob to send unsolicited ND on link-layer address change")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If skb_put_padto() fails then it frees the skb. I shifted that code
up a bit to make my error handling a little simpler.
Fixes: a0d2f20650e8 ("Renesas Ethernet AVB PTP clock driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise, UDP checksum offloads could corrupt ESP packets by attempting
to calculate UDP checksum when this inner UDP packet is already protected
by IPsec.
One way to reproduce this bug is to have a VM with virtio_net driver (UFO
set to ON in the guest VM); and then encapsulate all guest's Ethernet
frames in Geneve; and then further encrypt Geneve with IPsec. In this
case following symptoms are observed:
1. If using ixgbe NIC, then it will complain with following error message:
ixgbe 0000:01:00.1: partial checksum but l4 proto=32!
2. Receiving IPsec stack will drop all the corrupted ESP packets and
increase XfrmInStateProtoError counter in /proc/net/xfrm_stat.
3. iperf UDP test from the VM with packet sizes above MTU will not work at
all.
4. iperf TCP test from the VM will get ridiculously low performance because.
Signed-off-by: Ansis Atteka <aatteka@ovn.org>
Co-authored-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David reported that doing the following:
ip li add red type vrf table 10
ip link set dev eth1 vrf red
ip addr add 127.0.0.1/8 dev red
ip link set dev eth1 up
ip li set red up
ping -c1 -w1 -I red 127.0.0.1
ip li del red
when either policy routing IP rules are present or the local table
lookup ip rule is before the l3mdev lookup results in a hang with
these messages:
unregister_netdevice: waiting for red to become free. Usage count = 1
The problem is caused by caching the dst used for sending the packet
out of the specified interface on a local route with a different
nexthop interface. Thus the dst could stay around until the route in
the table the lookup was done is deleted which may be never.
Address the problem by not forcing output device to be the l3mdev in
the flow's output interface if the lookup didn't use the l3mdev. This
then results in the dst using the right device according to the route.
Changes in v2:
- make the dev_out passed in by __ip_route_output_key_hash correct
instead of checking the nh dev if FLOWI_FLAG_SKIP_NH_OIF is set as
suggested by David.
Fixes: 5f02ce24c2696 ("net: l3mdev: Allow the l3mdev to be a loopback")
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Suggested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We dereference "skb" to get "skb->len" so we should probably do that
step before freeing the skb.
Fixes: eea221ce4880 ("tc35815 driver update (take 2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have observed a sudden spike in rx/tx_packets and rx/tx_bytes
reported under /proc/net/dev. There is a race in mlx5e_update_stats()
and some of the get-stats functions (the one that we hit is the
mlx5e_get_stats() which is called by ndo_get_stats64()).
In particular, the very first thing mlx5e_update_sw_counters()
does is 'memset(s, 0, sizeof(*s))'. For example, if mlx5e_get_stats()
is unlucky at one point, rx_bytes and rx_packets could be 0. One second
later, a normal (and much bigger than 0) value will be reported.
This patch is to use a 'struct mlx5e_sw_stats temp' to avoid
a direct memset zero on priv->stats.sw.
mlx5e_update_vport_counters() has a similar race. Hence, addressed
together. However, memset zero is removed instead because
it is not needed.
I am lucky enough to catch this 0-reset in rx multicast:
eth0: 41457665 76804 70 0 0 70 0 47085 15586634 87502 3 0 0 0 3 0
eth0: 41459860 76815 70 0 0 70 0 47094 15588376 87516 3 0 0 0 3 0
eth0: 41460577 76822 70 0 0 70 0 0 15589083 87521 3 0 0 0 3 0
eth0: 41463293 76838 70 0 0 70 0 47108 15595872 87538 3 0 0 0 3 0
eth0: 41463379 76839 70 0 0 70 0 47116 15596138 87539 3 0 0 0 3 0
v2: Remove memset zero from mlx5e_update_vport_counters()
v1: Use temp and memcpy
Fixes: 9218b44dcc05 ("net/mlx5e: Statistics handling refactoring")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace ifdefs with SIMPLE_DEV_PM_OPS helper macro.
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Update lpfc version to reflect this set of changes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The older sli4 adapters only supported the 64 byte WQE entry size.
The new adapter (fw) support both 64 and 128 byte WQE entry sizies.
The Express lane WQ was not being created with the 128 byte WQE sizes
when it was supported.
Not having the right WQE size created for the express lane work queue
caused the the firmware to overwrite the lun indentifier in the FCP header.
This patch correctly creates the express lane work queue with the
supported size.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The driver with nvme had this routine stubbed.
Right now XRI_ABORTED_CQE is not handled and the FC NVMET
Transport has a new API for the driver.
Missing code path, new NVME abort API
Update ABORT processing for NVMET
There are 3 new FC NVMET Transport API/ template routines for NVMET:
lpfc_nvmet_xmt_fcp_release
This NVMET template callback routine called to release context
associated with an IO This routine is ALWAYS called last, even
if the IO was aborted or completed in error.
lpfc_nvmet_xmt_fcp_abort
This NVMET template callback routine called to abort an exchange that
has an IO in progress
nvmet_fc_rcv_fcp_req
When the lpfc driver receives an ABTS, this NVME FC transport layer
callback routine is called. For this case there are 2 paths thru the
driver: the driver either has an outstanding exchange / context for the
XRI to be aborted or not. If not, a BA_RJT is issued otherwise a BA_ACC
NVMET Driver abort paths:
There are 2 paths for aborting an IO. The first one is we receive an IO and
decide not to process it because of lack of resources. An unsolicated ABTS
is immediately sent back to the initiator as a response.
lpfc_nvmet_unsol_fcp_buffer
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
The second one is we sent the IO up to the NVMET transport layer to
process, and for some reason the NVME Transport layer decided to abort the
IO before it completes all its phases. For this case there are 2 paths
thru the driver:
the driver either has an outstanding TSEND/TRECEIVE/TRSP WQE or no
outstanding WQEs are present for the exchange / context.
lpfc_nvmet_xmt_fcp_abort
if (LPFC_NVMET_IO_INP)
lpfc_nvmet_sol_fcp_issue_abort (ABORT_WQE)
lpfc_nvmet_sol_fcp_abort_cmp
else
lpfc_nvmet_unsol_fcp_issue_abort
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
lpfc_nvmet_unsol_fcp_abort_cmp
Context flags:
LPFC_NVMET_IOP - his flag signifies an IO is in progress on the exchange.
LPFC_NVMET_XBUSY - this flag indicates the IO completed but the firmware
is still busy with the corresponding exchange. The exchange should not be
reused until after a XRI_ABORTED_CQE is received for that exchange.
LPFC_NVMET_ABORT_OP - this flag signifies an ABORT_WQE was issued on the
exchange.
LPFC_NVMET_CTX_RLS - this flag signifies a context free was requested,
but we are deferring it due to an XBUSY or ABORT in progress.
A ctxlock is added to the context structure that is used whenever these
flags are set/read within the context of an IO.
The LPFC_NVMET_CTX_RLS flag is only set in the defer_relase routine when
the transport has resolved all IO associated with the buffer. The flag is
cleared when the CTX is associated with a new IO.
An exchange can has both an LPFC_NVMET_XBUSY and a LPFC_NVMET_ABORT_OP
condition active simultaneously. Both conditions must complete before the
exchange is freed.
When the abort callback (lpfc_nvmet_xmt_fcp_abort) is envoked:
If there is an outstanding IO, the driver will issue an ABORT_WQE. This
should result in 3 completions for the exchange:
1) IO cmpl with XB bit set
2) Abort WQE cmpl
3) XRI_ABORTED_CQE cmpl
For this scenerio, after completion #1, the NVMET Transport IO rsp
callback is called. After completion #2, no action is taken with respect
to the exchange / context. After completion #3, the exchange context is
free for re-use on another IO.
If there is no outstanding activity on the exchange, the driver will send a
ABTS to the Initiator. Upon completion of this WQE, the exchange / context
is freed for re-use on another IO.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
NVMET didn't have any RSCN handling at all and
would not execute implicit LOGO when receiving a PLOGI
from an rport that NVMET had in state UNMAPPED.
Clean up the logic in lpfc_nlp_state_cleanup for
initiators (FCP and NVME). NVMET should not respond to
RSCN including allocating new ndlps so this code was
conditionalized when nvmet_support is true. The check
for NLP_RCV_PLOGI in lpfc_setup_disc_node was moved
below the check for nvmet_support to allow the NVMET
to recover initiator nodes correctly. The implicit
logo was introduced with lpfc_rcv_plogi when NVMET gets
a PLOGI on an ndlp in UNMAPPED state. The RSCN handling
was modified to not respond to an RSCN in NVMET. Instead
NVMET sends a GID_FT and determines if an NVMEP_INITIATOR
it has is UNMAPPED but no longer in the zone membership.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Adding support for Fabric assigned WWPN and WWNN.
Firmware sends first FLOGI to fabric with vendor version changes.
On link up driver gets updated service parameter with FAWWN assigned port
name. Driver sends 2nd FLOGI with updated fawwpn and modifies the
vport->fc_portname in driver.
Note:
Soft wwpn will not be allowed when fawwpn is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Cannot set NVME segment counts to a large number
The existing module parameter lpfc_sg_seg_cnt is used for both
SCSI and NVME.
Limit the module parameter lpfc_sg_seg_cnt to 128 with the
default being 64 for both NVME and NVMET, assuming NVME is enabled in the
driver for that port. The driver will set max_sgl_segments in the
NVME/NVMET template to lpfc_sg_seg_cnt + 1.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
When RPI is not available, driver sends WQE with invalid RPI value and
rejected by HBA.
lpfc 0000:82:00.3: 1:3154 BLS ABORT RSP failed, data: x3/xa0320008
and
lpfc :2753 PLOGI failure DID:FFFFFA Status:x3/xa0240008
In this case, driver accesses rpi_ids array out of bounds.
Fix:
Check return value of lpfc_sli4_alloc_rpi(). Do not allocate
lpfc_nodelist entry if RPI is not available.
When RPI is not available, we will get discovery timeouts and
command drops for some of the vports as seen below.
lpfc :0273 Unexpected discovery timeout, vport State x0
lpfc :0230 Unexpected timeout, hba link state x5
lpfc :0111 Dropping received ELS cmd Data: x0 xc90c55 x0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The symptom is that the driver will fail to login to the fabric.
The reason is because it is out of iocb resources.
There is a one to one relationship between MRQs
(receive buffers for NVMET-FC) and iocbs and the default number of
IOCBs was not accounting for the number of MRQs that were being created.
This fix aligns the number of MRQ resources with the total resources so
that it can handle fabric events when needed.
Also the initialization of ctxlock to be on FCP commands, NOT LS commands.
And modified log messages so that the log output can be correlated with
the analyzer trace.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Unnecessary lock is taken. ring lock should be sufficient to protect the
work queue submission.
This was noticed when doing performance testing. The hbalock is not
needed to issue io to the nvme work queue.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Fix nvme initiator handline when CONFIG_LPFC_NVME_INITIATOR is not enabled.
With update nvme upstream driver sources, loading
the driver with nvme enabled resulting in this Oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: lpfc_nvme_update_localport+0x23/0xd0 [lpfc]
PGD 0
Oops: 0000 [#1] SMP
CPU: 0 PID: 10256 Comm: lpfc_worker_0 Tainted
Hardware name: ...
task: ffff881028191c40 task.stack: ffff880ffdf00000
RIP: 0010:lpfc_nvme_update_localport+0x23/0xd0 [lpfc]
RSP: 0018:ffff880ffdf03c20 EFLAGS: 00010202
Cause: As the initiator driver completes discovery at different stages,
it call lpfc_nvme_update_localport to hint that the DID and role may have
changed. In the implementation of lpfc_nvme_update_localport, the driver
was not validating the localport or the lport during the execution
of the update_localport routine. With the recent upstream additions to
the driver, the create_localport routine didn't run and so the localport
was NULL causing the page-fault Oops.
Fix: Add the CONFIG_LPFC_NVME_INITIATOR preprocessor inclusions to
lpfc_nvme_update_localport to turn off all routine processing when
the running kernel does not have NVME configured. Add NULL pointer
checks on the localport and lport in lpfc_nvme_update_localport and
dump messages if they are NULL and just exit.
Also one alingment issue fixed.
Repalces the ifdef with the IS_ENABLED macro.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
There are two versions of a structure for queue creation and setup that the
driver shares with FW. The driver was only treating as version 0.
Verify WQ_CREATE with 128B WQEs in V0 and V1.
Code review of another bug showed the driver passing
128B WQEs and 8 pages in WQ CREATE and V0.
Code inspection/instrumentation showed that the driver
uses V0 in WQ_CREATE and if the caller passes queue->entry_size
128B, the driver sets the hdr_version to V1 so all is good.
When I tested the V1 WQ_CREATE, the mailbox failed causing
the driver to unload.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
There are couple of different load/unload issues fixed with this patch.
One of the issues was reported by Junichi Nomura, a patch was submitted
by Johannes Thumsrhirn which did fix one of the problems but the fix in
this patch separates the pring free from the queue free and does not set
the parameter passed in to NULL.
issues:
(1) driver could not be unloaded and reloaded without some Oops or
Panic occurring.
(2) The driver was panicking because of a corruption in the Memory
Manager when the iocb list was getting allocated.
Root cause for the memory corruption was a double free of the Work Queue
ring pointer memory - Freed once in the lpfc_sli4_queue_free when the CQ
was destroyed and again in lpfc_sli4_queue_free when the WQ was destroyed.
The pring free and the queue free were separated, the pring free was moved
to the wq destroy routine because it a better fit logically to delete the
ring with the wq.
The checkpatch flagged several alignmenet issues that were also corrected
with this patch.
The mboxq was never initialed correctly before it was used by the driver
this patch corrects that issue.
Reported-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
|
|
PRLI ACC from target is FCP oriented.
Word 0 was wrong. This was noticed by another nvmet-fc vendor that
was testing the lpfc nvme-fc initiator with their target.
Verified results with analyzer.
PRLI
BC B5 56 56 22 61 04 00 00 61 00 00 01 29 00 00 20 00 00 00
00 10 FF FF 00 00 00 00 20 14 00 18 28 00 00 00 00 00 00 00
00 00 00 00 00 00 00 20 00 00 00 00 9C D8 DA C9 BC 95 75 75
ACC
BC B5 56 56 23 61 00 00 00 61 04 00 01 98 00 00 30 00 00 00
00 10 00 18 00 00 00 00 02 14 00 18 28 00 01 00 00 00 00 00
00 00 00 00 00 00 00 18 00 00 00 00 B0 6B 07 57 BC B5 75 75
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
An extra blank line was being added the the rqpair printing.
Remove the extra line feed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The check for NULL ptr is not necessary, kfree will check it.
Removing NULL ptr check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
These defines for the posting of buffers for nvmet target were not used.
Removing the unused defines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Comment should have said Repost.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The xri resources are split into pools for NVME and FCP IO when NVME is
enabled. There was not message in the log that identified this allocation.
Added debug message to log XRI split.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
In the lpfc_nvme_io_cmd_wqe_cmpl routine the driver was printing two
pointers and the DID for the rport whenever an IO completed on a now
that had transitioned to a non active state.
There is no need to print the node pointer address for a node that
is not active the DID should be enough to debug.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
In this case, the NVME initiator is sending an LS REQ command on an NDLP
that is not MAPPED. The FW rejects it.
The lpfc_nvme_ls_req routine checks for a NULL ndlp pointer
but does not check the NDLP state. This allows the routine
to send an LS IO when the ndlp is disconnected.
Check the ndlp for NULL, actual node, Target and MAPPED
or Initiator and UNMAPPED. This avoids Fabric nodes getting
the Create Association or Create Connection commands. Initiators
are free to Reject either Create.
Also some of the messages numbers in lpfc_nvme_ls_req were changed because
they were already used in other log messages.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
