| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes the way an I-PDU is saved in case it needs to be sent
again. It is now copied using pskb_copy() and not simply referenced
using skb_get() since it could be modified by the driver.
digital_in_send_saved_skb() and digital_tg_send_saved_skb() still get a
reference on the saved skb which is re-sent but release it if the send
operation fails. That way the caller doesn't have to take care about skb
ref in case of error.
RTOX supervisor PDU must not be saved as this can override a previously
saved I-PDU that should be re-sent later on.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
irq 17: nobody cared (try booting with the "irqpoll" option)
handlers:
[<ffffffff81374370>] pcie_isr
[<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
[<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
Disabling IRQ #17
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Apply nvidia_bugs quirk only on root bus
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Reintroduce scanning of secondary buses
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the following commit:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
... early quirks are only applied to devices on the root bus.
The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.
We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This is to fix some conflicts in iwlwifi.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
drivers/net/wireless/intel/iwlwifi/mvm/scan.c
|
|
This showed up as "6Failed to access..." here.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 1b74dde7c47c ("x86/cpu: Convert printk(KERN_<LEVEL> ...) to pr_<level>(...)")
Link: http://lkml.kernel.org/r/1468170841-17045-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull MIPS fix from Ralf Baechle:
"Another week with just a single 4.7 fix.
This fixes a possible 'loss' of the huge page bit from pmd on
permission change"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix page table corruption on THP permission changes.
|
|
Mathieu Desnoyers reported that the STACK_FRAME_NON_STANDARD macro
wasn't working with the lttng_filter_interpret_bytecode() function in
the lttng-modules code.
Usually the relocation created by STACK_FRAME_NON_STANDARD creates a
reference to a section symbol like this:
Offset Type Value Addend Name
000000000000000000 X86_64_64 000000000000000000 +3136 .text
But in this case it created a reference to a function symbol:
Offset Type Value Addend Name
000000000000000000 X86_64_64 0x00000000000003a0 +0 lttng_filter_interpret_bytecode
To be honest I have no idea what causes gcc to decide to do one over the
other. But both are valid ELF, so add support for the function symbol.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lttng-dev@lists.lttng.org
Link: http://lkml.kernel.org/r/9cee42843bc6d94e990a152e4e0319cfdf6756ef.1466023450.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the prep work I did before enabling BH while handling socket backlog,
I missed two points in DCCP :
1) dccp_v4_ctl_send_reset() uses bh_lock_sock(), assuming BH were
blocked. It is not anymore always true.
2) dccp_v4_route_skb() was using __IP_INC_STATS() instead of
IP_INC_STATS()
A similar fix was done for TCP, in commit 47dcc20a39d0
("ipv4: tcp: ip_send_unicast_reply() is not BH safe")
Fixes: 7309f8821fd6 ("dccp: do not assume DCCP code is non preemptible")
Fixes: 5413d1babe8f ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)
Fixes: d67b8c616b48 ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb11ccb ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_forward_change() runs with RTNL held.
We are allowed to sleep if required.
If we use __in_dev_get_rtnl() instead of __in_dev_get_rcu(),
we no longer have to use GFP_ATOMIC allocations in
inet_netconf_notify_devconf(), meaning we are less likely to miss
notifications under memory pressure, and wont touch precious memory
reserves either and risk dropping incoming packets.
inet_netconf_get_devconf() can also use GFP_KERNEL allocation.
Fixes: edc9e748934c ("rtnl/ipv4: use netconf msg to advertise forwarding status")
Fixes: 9e5511106f99 ("rtnl/ipv4: add support of RTM_GETNETCONF")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jon Mason says:
====================
net: ethernet: bgmac: Add platform device support
David Miller, Please consider including patches 1-5 in net-next
Florian Fainelli, Please consider including patches 6 & 7 in
devicetree/next
Changes in v2:
* Made device tree binding changes suggested by Sergei Shtylyov,
Ray Jui, Rob Herring, Florian Fainelli, and Arnd Bergmann
* Removed devm_* error paths in the bgmac_platform.c suggested by
Florian Fainelli
* Added Arnd Bergmann's Acked-by to the first 5 (there were changes
outlined in the bullets above, but I believe them to be minor enough
for him to not revoke his acks)
This patch series adds support for other, non-bcma iProc SoC's to the
bgmac driver. This series only adds NSP support, but we are interested
in adding support for the Cygnus and NS2 families (with more possible
down the road).
To support non-bcma enabled SoCs, we need to add the standard device
tree "platform device" support. Unfortunately, this driver is very
tighly coupled with the bcma bus and much unwinding is needed. I tried
to break this up into a number of patches to make it more obvious what
was being done to add platform device support. I was able to verify
that the bcma code still works using a 53012K board (NS SoC), and that
the platform code works using a 58625K board (NSP SoC).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcma portion of the driver has been split off into a bcma specific
driver. This has been mirrored for the platform driver. The last
references to the bcma core struct have been changed into a generic
function call. These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver. In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct. In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus. This will help with the upcoming BCMA
removal from the bgmac driver. Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.
Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present. In
addition to the moving of the driver, this reset function is added.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. So,
simply change all of the bgmac_* prints to their dev_* counterparts. In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.
Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hayes Wang says:
====================
r8152: remove the redundant code
Remove the unnacessary code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 90186af404ad ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Horman says:
====================
net: support MPLS in IPv4 and UDP
This short series provides support for MPLS in IPv4 (RFC4023), and by
virtue of FOU, MPLS in UDP (RFC7510).
The changes are as follows:
1. Teach tunnel4.c about AF_MPLS, it already understands AF_INET and
AF_INET6
2. Enhance IPIP and SIT to handle MPLS. Both already handle IPv4.
SIT also already handles IPv6.
3. Trivially enhance MPLS to allow routes over SIT and IPIP tunnels.
A corresponding patch set for iproute2 has also been provided.
Changes since v1
* Correct inverted IPIP protocol logic in SIT patch
* Provide usage example below
Sample configuration follows:
* The following creates a tunnel and routes MPLS packets whose outermost
label is 100 over it. The forwarded packets will have the outermost label
stack entry, 100, removed and two label stack entries added, the
outermost having label 200 and the next having label 300.
The local end-point for the tunnel is 10.0.99.192 and the remote
endpoint is 10.0.99.193.
The local address for encapsulated packets is 10.0.98.192 and the
remote address is 10.0.98.193.
# Create an MPLS over IPv4 tunnel using the IPIP driver
ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
ttl 225 mode mplsip
# Bring the tunnel up and an add an IPv4 address and route
ip link set up dev tun1
ip addr add 10.0.98.192/24 dev tun1
# Set MPLS route
# Allow MPLS forwarding of packets recieved on eth0
echo 1 > /proc/sys/net/mpls/conf/eth0/input
# Larger than label to be routed (100)
echo 101 > /proc/sys/net/mpls/platform_labels
ip -f mpls route add 100 as 200/300 via inet 10.0.98.193
* For FOU (in this case MPLS over UDP) a tunnel may created using:
# Packets recieved on UDP port 6635 are MPLS over UDP (IP proto 137)
ip fou add port 6635 ipproto 137
# Create the tunnel netdev
ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
ttl 225 mode mplsip encap fou encap-sport auto encap-dport 6635
IPv4 address, link and route, and MPLS routing commands are as per
the MPLS over IPv4 example
* To use the SIT driver instead of the IPIP driver "ipip" may be substituted
for "sit" in the above examples.
* To create a tunnel that forwards and receives all supported
inner-protocols "mplsip" may be substituted for "any" in the above
examples.
For the IPIP driver this configures both IPv4 and MPLS over IPv4.
For the SIT driver this configures IPv6, IPv4 and MPLS over IPv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow MPLS routes on IPIP and SIT devices now that they
support forwarding MPLS packets.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the IPIP driver to support MPLS over IPv4. The implementation is an
extension of existing support for IPv4 over IPv4 and is based of multiple
inner-protocol support for the SIT driver.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the SIT driver to support MPLS over IPv4. This implementation
extends existing support for IPv6 over IPv4 and IPv4 over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend tunnel support to MPLS over IPv4. The implementation extends the
existing differentiation between IPIP and IPv6 over IPv4 to also cover MPLS
over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Falcon says:
====================
ibmvnic driver bugfixes and improvements
Miscellaneous fixes and improvements on the ibmvnic driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.
[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1
Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The controller device attributes are not used and expose no valuable
information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The connection link attributes are not used and expose no valuable
information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
cpufeatures.h currently defines X86_BUG(9) twice on 32-bit:
#define X86_BUG_NULL_SEG X86_BUG(9) /* Nulling a selector preserves the base */
...
#ifdef CONFIG_X86_32
#define X86_BUG_ESPFIX X86_BUG(9) /* "" IRET to 16-bit SS corrupts ESP/RSP high bits */
#endif
I think what happened was that this added the X86_BUG_ESPFIX, but
in an #ifdef below most of the bugs:
58a5aac53313 x86/entry/32: Introduce and use X86_BUG_ESPFIX instead of paravirt_enabled
Then this came along and added X86_BUG_NULL_SEG, but collided
with the earlier one that did the bug below the main block
defining all the X86_BUG()s.
7a5d67048745 x86/cpu: Probe the behavior of nulling out a segment at boot time
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160618001503.CEE1B141@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When we introduced GSO support, if using auth the auth chunk was being
left queued on the packet even after the final segment was generated.
Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed
the packet len while not accounting for this left-over. This caused more
space to be used the next packet due to the chunk still being queued,
but space which wasn't allocated as its size wasn't accounted.
The fix is to only queue it back when we know that we are going to
generate another segment.
Fixes: 90017accff61 ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This code generates as static checker warning because htons(ETH_P_IPV6)
is always true. From the context it looks like the && was intended to
be !=.
Fixes: 94758f8de037 ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.
Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.
This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The referenced change added a netlink notifier for processing
device queue size events. These events are fired for all devices
but the registered callback assumed they only occurred for tun
devices. This fix adds a check (borrowed from macvtap.c) to discard
non-tun device events.
For reference, this fixes the following splat:
[ 71.505935] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 71.513870] IP: [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[ 71.519906] PGD 3f41f56067 PUD 3f264b7067 PMD 0
[ 71.524497] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 71.529374] gsmi: Log Shutdown Reason 0x03
[ 71.533417] Modules linked in:[ 71.533826] mlx4_en: eth1: Link Up
[ 71.539616] bonding w1_therm wire cdc_acm ehci_pci ehci_hcd mlx4_en ib_uverbs mlx4_ib ib_core mlx4_core
[ 71.549282] CPU: 12 PID: 7915 Comm: set.ixion-haswe Not tainted 4.7.0-dbx-DEV #8
[ 71.556586] Hardware name: Intel Grantley,Wellsburg/Ixion_IT_15, BIOS 2.58.0 05/03/2016
[ 71.564495] task: ffff887f00bb20c0 ti: ffff887f00798000 task.ti: ffff887f00798000
[ 71.571894] RIP: 0010:[<ffffffff8153c1a0>] [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[ 71.580327] RSP: 0018:ffff887f0079bbd8 EFLAGS: 00010202
[ 71.585576] RAX: fffffffffffffae8 RBX: ffff887ef6d03378 RCX: 0000000000000000
[ 71.592624] RDX: 0000000000000000 RSI: 0000000000000028 RDI: 0000000000000000
[ 71.599675] RBP: ffff887f0079bc48 R08: 0000000000000000 R09: 0000000000000001
[ 71.606730] R10: 0000000000000004 R11: 0000000000000000 R12: 0000000000000010
[ 71.613780] R13: 0000000000000000 R14: 0000000000000001 R15: ffff887f0079bd00
[ 71.620832] FS: 00007f5cdc581700(0000) GS:ffff883f7f700000(0000) knlGS:0000000000000000
[ 71.628826] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 71.634500] CR2: 0000000000000010 CR3: 0000003f3eb62000 CR4: 00000000001406e0
[ 71.641549] Stack:
[ 71.643533] ffff887f0079bc08 0000000000000246 000000000000001e ffff887ef6d00000
[ 71.650871] ffff887f0079bd00 0000000000000000 0000000000000000 ffffffff00000000
[ 71.658210] ffff887f0079bc48 ffffffff81d24070 00000000fffffff9 ffffffff81cec7a0
[ 71.665549] Call Trace:
[ 71.667975] [<ffffffff810eeb0d>] notifier_call_chain+0x5d/0x80
[ 71.673823] [<ffffffff816365d0>] ? show_tx_maxrate+0x30/0x30
[ 71.679502] [<ffffffff810eeb3e>] __raw_notifier_call_chain+0xe/0x10
[ 71.685778] [<ffffffff810eeb56>] raw_notifier_call_chain+0x16/0x20
[ 71.691976] [<ffffffff8160eb30>] call_netdevice_notifiers_info+0x40/0x70
[ 71.698681] [<ffffffff8160ec36>] call_netdevice_notifiers+0x16/0x20
[ 71.704956] [<ffffffff81636636>] change_tx_queue_len+0x66/0x90
[ 71.710807] [<ffffffff816381ef>] netdev_store.isra.5+0xbf/0xd0
[ 71.716658] [<ffffffff81638350>] tx_queue_len_store+0x50/0x60
[ 71.722431] [<ffffffff814a6798>] dev_attr_store+0x18/0x30
[ 71.727857] [<ffffffff812ea3ff>] sysfs_kf_write+0x4f/0x70
[ 71.733274] [<ffffffff812e9507>] kernfs_fop_write+0x147/0x1d0
[ 71.739045] [<ffffffff81134a4f>] ? rcu_read_lock_sched_held+0x8f/0xa0
[ 71.745499] [<ffffffff8125a108>] __vfs_write+0x28/0x120
[ 71.750748] [<ffffffff8111b137>] ? percpu_down_read+0x57/0x90
[ 71.756516] [<ffffffff8125d7d8>] ? __sb_start_write+0xc8/0xe0
[ 71.762278] [<ffffffff8125d7d8>] ? __sb_start_write+0xc8/0xe0
[ 71.768038] [<ffffffff8125bd5e>] vfs_write+0xbe/0x1b0
[ 71.773113] [<ffffffff8125c092>] SyS_write+0x52/0xa0
[ 71.778110] [<ffffffff817528e5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[ 71.784472] Code: 45 31 f6 48 8b 93 78 33 00 00 48 81 c3 78 33 00 00 48 39 d3 48 8d 82 e8 fa ff ff 74 25 48 8d b0 40 05 00 00 49 63 d6 41 83 c6 01 <49> 89 34 d4 48 8b 90 18 05 00 00 48 39 d3 48 8d 82 e8 fa ff ff
[ 71.803655] RIP [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[ 71.809769] RSP <ffff887f0079bbd8>
[ 71.813213] CR2: 0000000000000010
[ 71.816512] ---[ end trace 4db6449606319f73 ]---
Fixes: 1576d9860599 ("tun: switch to use skb array for tx")
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two more fixes:
* handle allocation failures in new(ish) A-MSDU decapsulation
* don't leak memory on nl80211 ACL parse errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Improve conn/call lookup and fix call number generation [ver #3]
I've fixed a couple of patch descriptions and excised the patch that
duplicated the connections list for reconsideration at a later date.
For reference, the excised patch is sitting on the rxrpc-experimental
branch of my git tree, based on top of the rxrpc-rewrite branch. Diffing
it against yesterday's tag shows no differences.
Would you prefer the patch set to be emailed afresh instead of a git-pull
request?
David
---
Here's the next part of the AF_RXRPC rewrite. The two main purposes of
this set are to fix the call number handling and to make use of RCU when
looking up the connection or call to pass a received packet to.
Important changes in this set include:
(1) Avoidance of placing stack data into SG lists in rxkad so that kernel
stacks can become vmalloc'd (Herbert Xu).
(2) Calls cease pinning the connection they used as soon as possible,
which allows the connection to be discarded sooner and allows the call
channel on that connection to be reused earlier.
(3) Make each call channel on a connection have a separate and independent
call number space rather than having a shared number space for the
connection. Call numbers should increment monotonically per channel
on the client, and the server should ignore a call with a lower call
number for that channel than the latest it has seen. The RESPONSE
packet sets the minimum values of each call ID counter on a
connection.
(4) Look up calls by indexing the channel array on a connection rather
than by keeping calls in an rbtree on that connection. Also look up
calls using the channel array rather than using a hashtable.
The call hashtable can then be removed.
(5) Call terminal statuses are cached in the channel array for the last
call. It is assumed that if we the server have seen call N, then the
client no longer cares about call N-1 on the same channel.
This will allow retransmission of the terminal status in future
without the need to keep the rxrpc_call struct around.
(6) Peer lookups are moved out of common connection handling code and into
service connection handling code as client connections (a) must point
to a peer before they can be used and (b) are looked up by a
machine-unique connection ID directly, so we only need to look up the
peer first if we're going to deal with a service call.
(7) The reference count on a connection is held elevated by 1 whilst it is
alive (ie. idle unused connections have a refcount of 1). The reaper
will attempt to change the refcount from 1->0 and skip if this cannot
be done, whilst look ups only increment the refcount if it's non-zero.
This makes the implementation of RCU lookups easier as we don't have
to get a ref on the connection or a lock on the connection list to
prevent a connection being reaped whilst we're contemplating queueing
a packet that initiates a new service call upon it.
If we need to get a connection, but there's a dead connection in the
tree, we use rb_replace_node() to replace the dead one with a new one.
(8) Use a seqlock to validate the walk over the service connection rbtree
attached to a peer when it's being walked in RCU mode.
(9) Make the incoming call/connection packet handling code use RCU mode
and locks and make it only take a reference if the call/connection
gets queued on a workqueue.
The intention is that the next set will introduce the connection lifetime
management and capacity limits to prevent clients from overloading the
server.
There are some fixes too:
(1) Verifying that a packet coming in to a client connection came from the
expected source.
(2) Fix handling of connection failure in client call creation where we
don't reinitialise the list linkage block and a second attempt to
unlink the failed connection oopses and also we don't set the state
correctly, which causes an assertion failure.
(3) New service calls were being added to the socket's accept queue under
the wrong lock.
Changes:
(V2) In rxrpc_find_service_conn_rcu() initialised the sequence number to 0.
Fixed the RCU handling in conn_service.c by introducing and using
rb_replace_node_rcu() as an RCU-safe alternative in
rxrpc_publish_service_conn().
Modified and used rcu_dereference_raw() to avoid RCU sparse warnings
in rxrpc_find_service_conn_rcu().
Added in some missing RCU dereference wrappers. It seems to be
necessary to turn on CONFIG_PROVE_RCU_REPEATEDLY as well as
CONFIG_SPARSE_RCU_POINTER to get the static __rcu annotation checking
to happen.
Fixed some other sparse warnings, including a missing ntohs() in
jumbo packet processing.
(V3) Fixed some commit descriptions.
Excised the patch that duplicated the connection list to separate out
the procfs list for reconsideration at a later date.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd296 ("ppp: take reference on channels netns")
Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new APIs for eliminating a copy on the receive path. These new APIs also
help in minimizing the number of memory barriers we end up issuing (in the
ringbuffer code) since we can better control when we want to expose the ring
state to the host.
The patch is being resent to address earlier email issues.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hfsc_sched is huge (size: 920, cachelines: 15), but we can get it to 14
cachelines by placing level after filter_cnt (covering 4 byte hole) and
reducing period/nactive/flags to u32 (period is just a counter,
incremented when class becomes active -- 2**32 is plenty for this
purpose, also, long is only 32bit wide on 32bit platforms anyway).
cl_vtperiod is exported to userspace via tc_hfsc_stats, but its period
member is already u32, so no precision is lost there either.
Cc: Michal Soltys <soltys@ziu.info>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes. One is the qla24xx MSI regression, one is a theoretical
problem over blacklist matching, which would bite USB badly if it ever
triggered and one is a system hang with a particular type of IPR
device"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla2xxx: Fix NULL pointer deref in QLA interrupt
SCSI: fix new bug in scsi_dev_info_list string matching
ipr: Clear interrupt on croc/crocodile when running with LSI
|
