| Age | Commit message (Collapse) | Author |
|---|
|
The Mecer Xtreme Mini S6 features a wireless module, based on a
Realtek 8723BS, which provides WLAN and Bluetooth connectivity via
SDIO and UART interfaces respectively.
Define a simple MMC power sequence that declares the GPIO pins
connected to the module's WLAN Disable and Bluetooth Disable pins
as active low reset signals, because both signals must be deasserted
for WLAN radio operation.
Configure the host's SDIO interface for High Speed mode with 1.8v
I/O signalling and IRQ detection over a 4-bit wide bus.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200406135006.23759-1-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
'bus-width' and pinctrl containing the bus-pins
should be in the same file, so add them to
all mmc nodes in 'px30.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200416183053.6045-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
There are 2 identical '#include' for 'rk3288-power.h',
so remove one of them.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200403180159.13387-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm/boot/dts/rk3188-radxarock.dt.yaml: gpio-leds:
'blue', 'green', 'sleep'
do not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The mmc-controller.yaml didn't explicitly say disable-wp is
for SD card slot only, but that is what it was designed for
in the first place.
Remove all disable-wp from emmc or sdio controllers.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20191219121954.2450-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm64/boot/dts/rockchip/rk3368-r88.dt.yaml: gpio-leds:
'work' does not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: pd_vio@15:
'pd_tcpc0@RK3399_PD_TCPC0', 'pd_tcpc1@RK3399_PD_TCPC1'
do not match any of the regexes:
'.*-names$', '.*-supply$', '^#.*-cells$',
'^#[a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$',
'^__.*__$', 'pinctrl-[0-9]+'
Fix error by replacing the wrong defines by the ones
mentioned in 'rk3399-power.h'.
make -k ARCH=arm64 dtbs_check
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428203003.3318-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy@1:
'#phy-cells' is a required property
The phy nodename is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy@1:
'#phy-cells' is a required property
The rtl8211e node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: phy@0:
'#phy-cells' is a required property
The rtl8211f node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Rockchip dtsi and dts files have been bulk-converted for the
remaining raw gpio numbers into their descriptive counterparts and
also got rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x
mappings, so remove the unused defines in 'rockchip.h' to prevent
that someone start using them again.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200512203524.7317-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The defines RK_FUNC_1 and RK_FUNC_2 are deprecated,
so replace them with the preferred form.
Restyle properties in the same line.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200512203524.7317-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The lack of unique context in '0f1decaa83b7 ("arm64: dts: qcom: sc7180:
Support ETMv4 power management")' caused the patch to be applied
off-by-one. Move the "arm,coresight-loses-context-with-cpu" properties
down one node, so that it applies to the ETMs and not the replicator.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The SRAM DT binding requires child nodes to use a certain node name
scheme.
Change the naming from scp-shmem to scp-sram to comply with that.
Link: https://lore.kernel.org/r/20200513103016.130417-19-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The common LED binding wants the LED node names to start with led- and
then have just a single number.
Changing the naming for the 8 user LEDs from using user<x> to led-<x>.
Also there is no default-trigger named "mmc0" in the kernel, so use the
more generic "disk-activity".
Link: https://lore.kernel.org/r/20200513103016.130417-18-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Mali binding insists on the GPU interrupts to be in ordered as: job,
mmu, gpu.
Sort the GPU interrupts and interrupt-names properties accordingly.
Link: https://lore.kernel.org/r/20200513103016.130417-17-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Most Arm Ltd. boards are employing a layered bus structure, to map
the hardware design (SoC, motherboard, IOFPGA) and structure the DTs.
The "simple-bus" nodes only allow a limited set of node names. Switch
to use *-bus to be binding compliant.
This relies on a pending dt-schema.git fix for now:
https://github.com/devicetree-org/dt-schema/pull/38
Link: https://lore.kernel.org/r/20200513103016.130417-16-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The SMMU name in the RevC FVP DT file was not fully binding compliant.
Adjust the node name to match the binding's list of allowed names, also
shuffle the order of the interrupts to comply with the expected order.
Link: https://lore.kernel.org/r/20200513103016.130417-15-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The UARTs for all Arm Ltd. boards were using "uart" as their node name
stub.
Replace that with the required "serial" string, to comply with the PL011
DT binding.
Link: https://lore.kernel.org/r/20200513103016.130417-14-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The EHCI/OCHI DT binding requires to use "usb" as the node name stub.
Replace the existing name with "usb" to comply with the binding.
Link: https://lore.kernel.org/r/20200513103016.130417-13-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The sama5d2 SoC has two dedicated I2C IPs that are enabled on
sama5d2_xplained. Add alias for the i2c devices to not rely on
probe order for the i2c device numbering.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200518114802.253660-1-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This adds touchscreen support to the Ux500 Samsung
GT-S7710 "Skomer" mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200516212913.485365-1-linus.walleij@linaro.org
|
|
The GIC ITS nodes in the fastmodel DTS files were not fully binding
compliant.
Use one of the allowed node names, also add the required #msi-cells
property for the older model.
Link: https://lore.kernel.org/r/20200513103016.130417-12-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The GIC DT nodes for the fastmodels were not fully compliant with the
DT binding, which has certain expectations about child nodes and their
size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Since the .dts files share interrupt nexus nodes across different
interrupt controllers (GICv2 vs. GICv3), we need to use the only
commonly allowed #address-size value of <1> for both.
Link: https://lore.kernel.org/r/20200513103016.130417-11-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The GIC DT nodes for the Juno boards were not fully compliant with
the DT binding, which has certain expectations about child nodes and
their size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Link: https://lore.kernel.org/r/20200513103016.130417-10-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The GIC DT binding only allows certain combinations of DT compatible
strings. The somewhat awkward "arm,cortex-a15-gic", "arm,cortex-a9-gic"
is not among those.
Drop that combination of different "cortex" based strings used for the
models, and replace it with the more useful combination including
"arm,gic-400".
Link: https://lore.kernel.org/r/20200513103016.130417-9-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Juno's mem-timer DT node was not fully compliant with the DT binding,
which has certain expectation about child nodes and their size and
address cells values.
Use a cell size of 1, as the binding requests, and spell out the ranges
property to be binding compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-8-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the gpio keys to the
root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-7-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks to the root node, since they do not depend on any
busses.
Link: https://lore.kernel.org/r/20200513103016.130417-6-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, the leds and the config bus
subtree to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The sfp compatible should be 'sff,sfp', not 'sff,sfp+'. We used patched
kernel where the latter was working.
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the config bus subtree
to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Use sdhci-caps-mask to forbid SDR104 mode on the SDIO capable SDHCI
controller. Without this the device cannot pass electromagnetic
interference certifications.
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The NV+ v2 has a WH1602 LCD panel (which is just a rebranded HD44780),
similar to the Netgear RN104, just with different GPIO assignments.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds dts for the Check Point L-50 from 600/1100 series
routers.
Specification:
-CPU: Marvell Kirkwood 88F6821 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Move the max-link-speed property of the PCIe node from board specific
device tree files to the generic armada-37xx.dtsi.
Armada 37xx supports only PCIe gen2 speed so max-link-speed property
should be in the generic armada-37xx.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.
This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Update the SolidRun Armada 8040 platforms phy interface types from the
old 10gbase-kr to the newer and more correct 10gbase-r.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add musb nodes and usb2 phy nodes for MT2701
Signed-off-by: Min Guo <min.guo@mediatek.com>
Link: https://lore.kernel.org/r/20191211015446.11477-3-min.guo@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The MediaTek MT7623 SoC contains a Mali-450, so add a compatible for it
and define its own vendor-specific properties.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/efeadefe3895bcadf1d2e9847b82206dd8c7ec35.1563867856.git.ryder.lee@mediatek.com
[mb: move to yaml file]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add a node for Mali-450.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/af7b5a2e00eb3a4b6262807c378e43afd5f74779.1563867856.git.ryder.lee@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Dhrystone benchmark on Acer Chromebook R13 CB5-312T:
A72: 15698587 dps @ 1807 MHz
A53: 7598784 dps @ 1703 MHz
Signed-off-by: Ulrich Hecht <uli-qwV78thtvt0@public.gmane.org>
Link: https://lore.kernel.org/r/1563529816-3992-1-git-send-email-uli@fpond.eu
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
