| Age | Commit message (Collapse) | Author |
|---|
|
Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mode
We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.
Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On x86_64 we have 3 holes in struct tbf_sched_data.
The member peak_present can be replaced with peak.rate_bytes_ps,
because peak.rate_bytes_ps is set only when peak is specified in
tbf_change(). tbf_peak_present() is introduced to test
peak.rate_bytes_ps.
The member max_size is moved to fill 32bit hole.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 9b2777d6089bc ("ieee802154: add TX power control to
wpan_phy") introduced the new function at86rf212_set_txpower() with
the questionable check of the return of __at86rf230_write() in the
exit path:
1) Both at86rf212_set_txpower() and __at86rf230_write() have the
same return type.
2) Whatever __at86rf230_write() returns becomes the return value of
at86rf212_set_txpower().
Thus, fix the exit path by getting rid of that check entirely.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a couple of patches fixing the same bug that
results in duplicated err = 0; assignment.
The patch removes one of them.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one. These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTT may be bogus with tall loss probe (TLP) when a packet
is retransmitted and latter (s)acked without TCPCB_SACKED_RETRANS flag.
For example, TLP calls __tcp_retransmit_skb() instead of
tcp_retransmit_skb(). The skb timestamps are updated but the sacked
flag is not marked with TCPCB_SACKED_RETRANS. As a result we'll
get bogus RTT in tcp_clean_rtx_queue() or in tcp_sacktag_one() on
spurious retransmission.
The fix is to apply the sticky flag TCP_EVER_RETRANS to enforce Karn's
check on RTT sampling. However this will disable F-RTO if timeout occurs
after TLP, by resetting undo_marker in tcp_enter_loss(). We relax this
check to only if any pending retransmists are still in-flight.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a sanity check and we never pass invalid values so this patch
doesn't change anything. However the node->time_in[] array has
HSR_MAX_SLAVE (2) elements and not HSR_MAX_DEV (3).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes, most of them SCHED_DEADLINE fallout"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Prevent rt_time growth to infinity
sched/deadline: Switch CPU's presence test order
sched/deadline: Cleanup RT leftovers from {inc/dec}_dl_migration
sched: Fix double normalization of vruntime
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull liblockdep fixes from Ingo Molnar:
"A handful of build fixes for liblockdep"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: Use realpath for srctree and objtree
tools/liblockdep: Add a stub for new rcu_is_watching
tools/liblockdep: Mark runtests.sh as executable
tools/liblockdep: Add include directory to allow tests to compile
tools/liblockdep: Fix include of asm/hash.h
tools/liblockdep: Fix initialization code path
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
There is a single framework fix that prevents dereferencing a NULL
pointer when calling clk_get. The range of fixes for clock driver
regressions spans memory leak fixes, touching the wrong registers that
cause things to explode, misconfigured clock rates that result in
non-responsive devices and even some boot failures. The most benign
fix is DT binding doc typo. It is a stable ABI exposed from the
kernel that was introduced in -rc1, so best to fix it now"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk:at91: Fix memory leak in of_at91_clk_master_setup()
clk: nomadik: fix multiplatform problem
clk: Correct handling of NULL clk in __clk_{get, put}
clk: shmobile: Fix typo in MSTP clock DT bindings
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent for all non-PLL clocks
clk: tegra124: remove gr2d and gr3d clocks
clk: tegra: Fix vic03 mux index
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent all non-PLL clocks
clk: tegra: use max divider if divider overflows
clk: tegra: cclk_lp has a pllx/2 divider
clk: tegra: fix sdmmc clks on Tegra1x4
clk: tegra: fix host1x clock on Tegra124
clk: tegra: PLLD2 fixes for hdmi
clk: tegra: Fix PLLD mnp table
clk: tegra: Fix PLLP rate table
clk: tegra: Correct clock number for UARTE
clk: tegra: Add missing Tegra20 fuse clks
ARM: keystone: dts: fix clkvcp3 control register address
...
|
|
In commit e2d265d3b587 (canfd: add support for CAN FD in CAN_RAW sockets)
CAN FD frames with a payload length up to 8 byte are passed to legacy
sockets where the CAN FD support was not enabled by the application.
After some discussions with developers at a fair this well meant feature
leads to confusion as no clean switch for CAN / CAN FD is provided to the
application programmer. Additionally a compatibility like this for legacy
CAN_RAW sockets requires some compatibility handling for the sending, e.g.
make CAN2.0 frames a CAN FD frame with BRS at transmission time (?!?).
This will become a mess when people start to develop applications with
real CAN FD hardware. This patch reverts the bad compatibility code
together with the documentation describing the removed feature.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the soft reset into a seperate function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds the missing netif_napi_del() to the flexcan_remove() function.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch factors out freeze and unfreeze of the CAN core into seperate
functions. Experiments have shown that the transition from and to freeze mode
may take several microseconds, especially the time entering the freeze mode
depends on the current bitrate.
This patch adds a while loop which polls the Freeze Mode ACK bit (FRZ_ACK) that
indicates a successfull mode change. If the function runs into a timeout a
error value is returned.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the transceiver enable and disable into seperate functions,
where the NULL pointer check is hidden.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In flexcan_chip_enable() and flexcan_chip_disable() fixed delays are used.
Experiments have shown that the transition from and to low power mode may take
several microseconds.
This patch adds a while loop which polls the Low Power Mode ACK bit (LPM_ACK)
that indicates a successfull mode change. If the function runs into a timeout a
error value is returned.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If flexcan_chip_start() in flexcan_open() fails, the interrupt is not freed,
this patch adds the missing cleanup.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When shutting down the CAN interface (ifconfig canX down) during high CAN bus
loads, the CAN core might hang and freeze the whole CPU.
This patch fixes the shutdown sequence by first disabling the CAN core then
disabling all interrupts.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
Add the USB device ID for the D-Link DUB-1312 USB 3.0 to Gigabit Ethernet
Adapter to the AX88179/178A driver.
Signed-off-by: Gerry Demaret <gerry@tigron.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
net/mlx4: Mellanox driver update 27-02-2014
This patchset contains some fixes for small trivial bugs, and
compilation/syntactic parsers warnings
Patchset was applied and tested over commit 750f679 "Merge branch '6lowpan'"
Changes from V1:
-patch 5/9: Replace mlx4_en_mac_to_u64() with mlx4_mac_to_u64()
- Remove unnecessary define of ETH_ALEN
Changes from V0:
-patch 3/9: net/mlx4_en: Pad ethernet packets smaller than 17 bytes
- Make condition more efficient
- Didn't use canonical function to pad buffer since using bounce buffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlx4_en driver support also 1Gbit and 40Gbit Ethernet devices,
changed the driver description in the menuconfig to reflect that.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When BlueFlame is turned on, control segment of the TX WQE is changed,
and the second line of it is used for QPN.
Changed code to use a union in the mlx4_wqe_ctrl_seg instead of casting.
This makes the code clearer and solves the static checker warning:
drivers/net/ethernet/mellanox/mlx4/en_tx.c:839 mlx4_en_xmit()
warn: potential memory corrupting cast 4 vs 2 bytes
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch force conversion to u32 to fix the following sparse warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1822:53: warning: restricted __be32
degrades to integer
Casting to u32 is safe here, because token will be returned as is
from the hardware without any modification.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Connect-X devices selftest speed test shouldn't fail on 1G and 40G link
speeds.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the EN driver uses a private static function
mlx4_en_mac_to_u64(). Move it to a common include file (driver.h)
for mlx4_en and mlx4_ib for further use.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Give accurate counters and avoids cache misses when several rings
update the counters of stop/wake queue.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware can't accept packets smaller than 17 bytes. Therefore need to
pad with zeros.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify mlx4_en module parameters.
In case they are out of range - reset to default values.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User priority limit has to be less than MLX4_EN_NUM_UP.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Aring says:
====================
6lowpan: fix issues with byte ordering types
I got some mail from a "kbuild test robot" and it detected some byte
ordering issues with the tag and datagram size value of 6LoWPAN IEEE
802.15.4 fragmentation header.
This patch series should fix the issues with the byte ordering.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initialization of the tag value doesn't matter at begin of
fragmentation. This patch removes the initialization to zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Datagram size value is u16 because we convert it to host byte order
and we need to read it. Only the tag value belongs to __be16 type.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aaron Brown says:
====================
Mark updates ixgbe for LER / adapter removal. He restores the HW
address in the recovery path so the device is not perpetually removed,
fixes up some removed state ethtool results and adds checks related to
config space access.
Jacob adds support for the new SIOCGHWTSTAMP ioctl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the new SIOCGHWTSTAMP ioctl, which enables a
process to determine the current timestamp configuration. In order to
implement this, store a copy of the timestamp configuration. In
addition, we can remove the 'int cmd' parameter as the new set_ts_config
function doesn't use it. I also fixed a typo in the function
description.
-v2
* Only save the settings after validating them
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuration space reads should also be checked for removal. So
add some checks related to config space accesses.
v2:
* Fixed indent
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ethtool tests returned apparently good results when the
adapter was in a removed state. Fix that by checking for removal.
This also fixes two paths that could return uninitialized memory
in data[4].
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hw_addr needs to be restored in the pcie recovery path or
else the device will be perpetually removed. Also restore the
value in the resume path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch b44_check_phy() was called when the phy called the
adjust callback. This method only change the mac duplex mode when the
carrier was off. When the phy changed the duplex mode after the carrier
was on the mac was not changed. This happened when an external phy was
used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When support for external phys was added to b44, the calls to start and
stop the phy were missing in the mac driver. This adds the calls to
phy_start() and phy_stop().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Not a huge amount happening, some MAINTAINERS updates, radeon, vmwgfx
and tegra fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: avoid null pointer dereference at failure paths
drm/vmwgfx: Make sure backing mobs are cleared when allocated. Update driver date.
drm/vmwgfx: Remove some unused surface formats
drm/radeon: enable speaker allocation setup on dce3.2
drm/radeon: change audio enable logic
drm/radeon: fix audio disable on dce6+
drm/radeon: free uvd ring on unload
drm/radeon: disable pll sharing for DP on DCE4.1
drm/radeon: fix missing bo reservation
drm/radeon: print the supported atpx function mask
MAINTAINERS: update drm git tree entry
MAINTAINERS: add entry for drm radeon driver
drm/tegra: Add guard to avoid double disable/enable of RGB outputs
gpu: host1x: do not check previously handled gathers
drm/tegra: fix typo 'CONFIG_TEGRA_DRM_FBDEV'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 2 USB patches for 3.14-rc5, one a new device id, and the
other fixes a reported problem with threaded irqs and the USB EHCI
driver"
* tag 'usb-3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: ehci: fix deadlock when threadirqs option is used
USB: ftdi_sio: add Cressi Leonardo PID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull sysfs fix from Greg KH:
"Here is a single sysfs fix for 3.14-rc5. It fixes a reported problem
with the namespace code in sysfs"
* tag 'driver-core-3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: fix namespace refcnt leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a few IIO fixes, and a new device id for a staging driver for
3.14-rc5. All have been in linux-next for a while, I did a final
merge to get the IIO fixes into this tree, they were incorrectly in
the char-misc tree for a few weeks, and I forgot to tell you to pull
them from there. This makes it a single pull request for you"
* tag 'staging-3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID
staging:iio:adc:MXS:LRADC: fix touchscreen statemachine
iio:gyro: bug on L3GD20H gyroscope support
iio: cm32181: Change cm32181 ambient light sensor driver
iio: cm36651: Fix read/write integration time function.
|
|
into drm-fixes
more radeon fixes
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: enable speaker allocation setup on dce3.2
drm/radeon: change audio enable logic
drm/radeon: fix audio disable on dce6+
drm/radeon: free uvd ring on unload
drm/radeon: disable pll sharing for DP on DCE4.1
drm/radeon: fix missing bo reservation
drm/radeon: print the supported atpx function mask
|
