| Age | Commit message (Collapse) | Author |
|---|
|
As of commit ba470de43188cdbff795b5da43a1474523c6c2fb ("map: handle
mlocked pages during map, remap, unmap") we now use the 'vma' variable
at the end of mmap_region() to handle the page-in of newly mapped
mlocked pages.
However, if we merged adjacent vma's together, the vma we're using may
be stale. We historically consciously avoided using it after the merge
operation, but that got overlooked when redoing the locked page
handling.
This commit simplifies mmap_region() by doing any vma merges early,
avoiding the issue entirely, and 'vma' will always be valid. As pointed
out by Hugh Dickins, this depends on any drivers that change the page
offset of flags to have set one of the VM_SPECIAL bits (so that they
cannot trigger the early merge logic), but that's true in general.
Reported-and-tested-by: Maksim Yevmenkin <maksim.yevmenkin@gmail.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix inverted logic
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 0f0ca340e57bd7446855fefd07a64249acf81223 ("phy: power
management support") caused a regression in the gianfar driver.
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a memory leak identified by Rusty Russell during LCA09 by
kfree'ing the lg object instead of just clearing it when the
launcher closes.
Signed-off-by: Mark Wallis <mwallis@serialmonkey.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Makes all the warnings go away when compiling lguest on Ubuntu on
Intrepid or greater.
Signed-off-by: Timothy R Ansell <mithro@mithis.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
3 points
lguest_asm.S => i386_head.S
LHCALL_BREAK => LHREQ_BREAK
perferred => preferred
Signed-off-by: Atsushi SAKAI <sakaia@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537
Free memory.
Signed-off-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon a report from Michael Tokarev <mjt@tls.msk.ru>:
Just saw in dmesg:
ioctl32(kvm:4408): Unknown cmd fd(9) cmd(800454cf){t:'T';sz:4} arg(ffc668e4) on /dev/net/tun
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Benjamin Zores <benjamin.zores@alcatel-lucent.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This documentation is old. Add a short note to describe why aliases
are no long necessary, and remove the old contact/edit info.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It oopsd for me in skb_seq_read. addr2line said it was
linux-2.6/net/core/skbuff.c:2228, which is this line:
while (st->frag_idx < skb_shinfo(st->cur_skb)->nr_frags) {
I added some printks in there and it looks like we hit this:
} else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
st->frag_idx = 0;
goto next_skb;
}
Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.
if (abs_offset < block_limit) {
- *data = st->cur_skb->data + abs_offset;
+ *data = st->cur_skb->data + (abs_offset - st->stepped_offset);
I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -
It hit this if condition -
if (st->cur_skb->next) {
st->cur_skb = st->cur_skb->next;
st->frag_idx = 0;
goto next_skb;
And so, now the st pointer is shifted to the next skb whereas actually
it should have hit the second else if first since the data is in the
frag_list.
else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
goto next_skb;
}
Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches.
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch ensures that memory gets properly mapped into the PCI
address space. Without this patch, the memory window BAR is left
at whatever value happened to be loaded into the BAR when Linux
was booted. Without this patch, memory could end up getting mapped
at any of the 1G address boundaries instead of at '0' where Linux
expects it.
Similarly, this patch also ensures that the internally memory mapped
registers (IMMR) are mapped to the correct PCI address range.
Without this patch, PCI appears to work correctly until a PCI
device is inserted which DMAs into memory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The frag_list handling was broken in skb_seq_read:
1) We didn't add the stepped offset when looking at the head
are of fragments other than the first.
2) We didn't take the stepped offset away when setting the data
pointer in the head area.
3) The frag index wasn't reset.
This patch fixes both issues.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348b4d5f1353e1d7feae30880b8b3e342
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes two issues with the sanity check loop when processing
the country IE:
1. Do not use frequency for the current subband channel check,
this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
on each subband as was done with a recent patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch fixes memcpy to NULL address when the ucode DMA allocation failure.
This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
His email address keeps bouncing, and he's not interested in mac80211
patches etc. anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
as per https://bugs.launchpad.net/bugs/294391. These got one sample of
each iPod generation going. However there still occurred I/O stalls
with the 3rd generation iPod which remain undiagnosed at the time of
this writing.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
According to https://bugs.launchpad.net/bugs/294391
- 3rd generation iPods need the "fix capacity" workaround after all
(apparently they crash after the last sector was accessed),
- 2nd generation iPods need the "128 kB maximum request size"
workaround.
Alas both iPod generations feature the same model ID in the config ROM,
hence we can only define a shared quirks list entry for them. Luckily
the fix capacity workaround did not show a negative effect in Jarod's
tests with 2nd gen. iPod.
A side note: Apple computers in target mode (or at least an x86 Mac
mini) don't have firmware_version and model_id, hence none of the iPod
quirks list entries is active for them.
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
|
|
|
|
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f8595a064b3f1a1837fea2177902589ac3 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes. Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
1: make "target_kb" only accept and produce a memory size in kilobytes.
2: add a second "target" file which produces output in bytes, and will accept
memparse input (scaled bytes)
This fixes the rather irritating problem that writing the same value
read back into target_kb would end up shrinking the domain by a factor
of 1024, with generally bad results.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: "dan.magenheimer@oracle.com" <dan.magenheimer@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
streaming.
Resetting the streaming flag on disconnection prevented the URBs to be freed
when streaming was active.
Also, USBs cannot be killed after disconnection (oops in [usbcore] unlink1).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Pre-emption Disabled
Trace: (Provided by Douglas)
BUG: sleeping function called from invalid context at drivers/usb/core/urb.c:558
in_atomic():0, irqs_disabled():1
Pid: 4918, comm: sox Not tainted 2.6.27.5 #1
[<c04246d8>] __might_sleep+0xc6/0xcb
[<c058c8b0>] usb_kill_urb+0x1a/0xd8
[<c0488e68>] ? __kmalloc+0x9b/0xfc
[<c0488e85>] ? __kmalloc+0xb8/0xfc
[<c058cd5a>] ? usb_alloc_urb+0xf/0x31
[<f8dd638c>] em28xx_isoc_audio_deinit+0x2f/0x6c [em28xx_alsa]
[<f8dd6573>] em28xx_cmd+0x1aa/0x1c5 [em28xx_alsa]
[<f8dd65e1>] snd_em28xx_capture_trigger+0x53/0x68 [em28xx_alsa]
[<f8aa8674>] snd_pcm_do_start+0x1c/0x23 [snd_pcm]
[<f8aa85d7>] snd_pcm_action_single+0x25/0x4b [snd_pcm]
[<f8aa9833>] snd_pcm_action+0x6a/0x76 [snd_pcm]
[<f8aa98f5>] snd_pcm_start+0x14/0x16 [snd_pcm]
[<f8aae10e>] snd_pcm_lib_read1+0x66/0x273 [snd_pcm]
[<f8aac5a3>] ? snd_pcm_kernel_ioctl+0x46/0x5f [snd_pcm]
[<f8aae4a7>] snd_pcm_lib_read+0xbf/0xcd [snd_pcm]
[<f8aad774>] ? snd_pcm_lib_read_transfer+0x0/0xaf [snd_pcm]
[<f89feeb6>] snd_pcm_oss_read3+0x99/0xdc [snd_pcm_oss]
[<f89fef9c>] snd_pcm_oss_read2+0xa3/0xbf [snd_pcm_oss]
[<c064169d>] ? _cond_resched+0x8/0x32
[<f89ff0be>] snd_pcm_oss_read+0x106/0x150 [snd_pcm_oss]
[<f89fefb8>] ? snd_pcm_oss_read+0x0/0x150 [snd_pcm_oss]
[<c048c6e2>] vfs_read+0x81/0xdc
[<c048c7d6>] sys_read+0x3b/0x60
[<c04039bf>] sysenter_do_call+0x12/0x34
=======================
The culprit in the trace is snd_pcm_action() which invokes a spin lock
which disables pre-emption which disables an IRQ which causes the
__might_sleep() function to fail the irqs_disabled() test. Since
pre-emption is enabled then it is safe to de-allocate the memory if
you first unlink each URB. In this instance you are safe since
pre-emption is disabled. If pre-emption and irqs are not disabled then
call usb_kill_urb(), else call usb_unlink_urb().
Thanks to Douglas for tracking down this bug originally!!!
[dougsland@redhat.com: Fixed codyingstyle]
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Move radio->muted and radio->stereo in section where radio mutex is
locked to avoid possible race condition problems or access to memory.
Thanks to David Ellingsworth <david@identd.dyndns.org> for pointing to
this weak place in driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
These days TUNER_SET_CONFIG is broadcast to the other i2c devices
and that triggers a fw load on the cx25840. Ignore this command
since cx25840 isn't a tuner and you really do not want to load
the firmware that early.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
First control messages to the stick timeouts very often due to probable
hw bug. Repeat first message few times if it fails as workaround.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Bug causes 2nd FE MPEG TS buffer size to be zero and therefore no picture
when 2nd FE was enabled. Configure correct buffer size also for 2nd FE.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
paging request at ffffffff
I'm using a "Hauppauge WinTV-NOVA-T DVB card" of PCI id "13c2:1005" with
kernel 2.6.27.9.
I've recently experienced the following fairly consistent kernel oops on
startup in grundig_29504_401_tuner_set_params from budget.c. As you
might expect, following this failure, the card doesn't work.
I'm not a kernel developer, nevertheless I seem to have managed to track
this down to a non-existent initialisation of
budget->dvb_frontend->tuner_priv.
The attached patch fixes the problem for me (and I've managed to tune
the card successfully as a result), but I don't know of anyone else
using the driver so I can't test it on other people.
Please let me know if this works for you or if I've done something
terribly wrong ;-(
BUG: unable to handle kernel paging request at ffffffff
IP: [<f8981e11>] :budget:grundig_29504_401_tuner_set_params+0x3b/0xf8
*pde = 007e0067 *pte = 00000000
Oops: 0000 [#1] SMP
Modules linked in: bridge stp bnep rfcomm l2cap asb100 hwmon_vid hwmon
fuse ipt_REJECT nf_conntrack_ipv4 iptable_filter ip_tables ip6t_REJECT
xt_tcpudp nf_conntrack_ipv6 xt_state nf_conntrack ip6table_filter
ip6_tables x_tables ipv6 loop dm_multipath scsi_dh ppdev snd_cmipci
gameport snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq
snd_pcm_oss snd_mixer_oss l64781 snd_pcm snd_page_alloc snd_opl3_lib
snd_timer parport_pc snd_hwdep parport btusb snd_mpu401_uart budget
budget_core snd_rawmidi bluetooth saa7146 snd_seq_device ttpci_eeprom
snd soundcore sr_mod i2c_sis96x cdrom dvb_core sis900 i2c_core floppy
pcspkr mii sata_sil sg dm_snapshot dm_zero dm_mirror dm_log dm_mod
pata_sis ata_generic pata_acpi libata sd_mod scsi_mod crc_t10dif ext3
jbd mbcache uhci_hcd ohci_hcd ehci_hcd [last unloaded: microcode]
Pid: 2319, comm: kdvb-fe-0 Not tainted (2.6.27.9-73.fc9.i686 #1)
EIP: 0060:[<f8981e11>] EFLAGS: 00010286 CPU: 0
EIP is at grundig_29504_401_tuner_set_params+0x3b/0xf8 [budget]
EAX: f6417f00 EBX: f6f53808 ECX: 00000000 EDX: ffffffff
ESI: f6f94404 EDI: f6417f00 EBP: f6417f10 ESP: f6417ef0
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process kdvb-fe-0 (pid: 2319, ti=f6417000 task=f642b2c0 task.ti=f6417000)
Stack: f6e39800 00000000 00000004 f6417f00 c064523c f6f53808 f6f53800 f6f94404
f6417f54 f8b2e45a f6417f24 00000286 f6417f4c f6417f38 00000000 00000286
f6417f3c c064520f f642b2c0 f6417f6c c064456f 00000001 f6f94400 00000001
Call Trace:
[<c064523c>] ? _spin_lock_irqsave+0x29/0x30
[<f8b2e45a>] ? apply_frontend_param+0x27/0x357 [l64781]
[<c064520f>] ? _spin_lock_irq+0x1c/0x20
[<c064456f>] ? __down_common+0x91/0xbf
[<f894f25d>] ? dvb_frontend_swzigzag_autotune+0x17d/0x1a4 [dvb_core]
[<f894f780>] ? dvb_frontend_swzigzag+0x1ac/0x209 [dvb_core]
[<f894fcc8>] ? dvb_frontend_thread+0x2eb/0x3b3 [dvb_core]
[<c043c166>] ? autoremove_wake_function+0x0/0x33
[<f894f9dd>] ? dvb_frontend_thread+0x0/0x3b3 [dvb_core]
[<c043bec3>] ? kthread+0x3b/0x61
[<c043be88>] ? kthread+0x0/0x61
[<c040494b>] ? kernel_thread_helper+0x7/0x10
=======================
Code: ec 14 8b 80 00 02 00 00 8b 93 08 02 00 00 8d 7d e4 8b 40 20 89 45
e0 31 c0 85 d2 f3 ab 8d 45 f0 66 c7 45 e8 04 00 89 45 ec 74 09 <0f> b6
02 66 89 45 e4 eb 06 66 c7 45 e4 61 00 8b 0e be 0a 8b 02
EIP: [<f8981e11>] grundig_29504_401_tuner_set_params+0x3b/0xf8 [budget]
SS:ESP 0068:f6417ef0
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
kerneloops.org is reporting a lot of these warnings that come due to
vmware not setting up any MTRRs for emulated CPUs:
| Reported 709 times (14696 total reports)
| BIOS bug (often in VMWare) where the MTRR's are set up incorrectly
| or not at all
|
| This warning was last seen in version 2.6.29-rc2-git1, and first
| seen in 2.6.24.
|
| More info:
| http://www.kerneloops.org/searchweek.php?search=mtrr_trim_uncached_memory
Keep a one-liner KERN_INFO about it - so that we have so notice if empty
MTRRs are caused by native hardware/BIOS weirdness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Revert a change made in change 9743 which resulted in a kernel panic in some
cases on shutdown of the audio stream.
First discovered when working on the Pinnacle 880e support, and later
reproduced by a user on the mailing list with the HVR-900 as well.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix for KWorld 330U AC97
Many thanks to Devin and Mauro again!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx: Fix audio URB transfer buffer memory leak and race
condition/corruption of capture pointer
Leak fix kindly contributed by Pádraig Brady.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
With the conversion to v4l2_subdev one bit of code was accidentally dropped:
on receiving the first command the driver has to load the fw. A new init()
command was introduced to do that explicitly for bridge drivers that are
converted to use v4l2_subdev, but old drivers that are not yet converted
no longer worked.
This patch fixes this regression for these old drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
