| Age | Commit message (Collapse) | Author |
|---|
|
The RXFC register is the only one being read using 8-bit accessors.
To make it easier to support the 16-bit accesses used by the parallel
bus variant of KS8851, use 16-bit accessor to read RXFC register as
well as neighboring RXFCTR register.
Remove ks8851_rdreg8() as it is not used anywhere anymore.
There should be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the SPI variant of KS8851, the MAC address can be programmed with
either 8/16/32-bit writes. To make it easier to support the 16-bit
parallel option of KS8851 too, switch both the MAC address programming
and readout to 16-bit operations.
Remove ks8851_wrreg8() as it is not used anywhere anymore.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851_rdreg32() is used only in one place, to read two registers
using a single read. To make it easier to support 16-bit accesses via
parallel bus later on, replace this single read with two 16-bit reads
from each of the registers and drop the ks8851_rdreg32() altogether.
If this has noticeable performance impact on the SPI variant of KS8851,
then we should consider using regmap to abstract the SPI and parallel
bus options and in case of SPI, permit regmap to merge register reads
of neighboring registers into single, longer, read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which
works for both SPI and platform drivers. This is done in preparation
for unifying the KS8851 SPI and parallel bus drivers.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use device managed version of alloc_etherdev() to simplify the code.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver probe function already has a struct device *dev pointer
and can easily derive of_node pointer from it, pass the of_node pointer as
a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev.
This is the only reference to spidev in the function, so get rid of it.
This is done in preparation for unifying the KS8851 SPI and parallel bus
drivers.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev
in the interrupt handler. This is the only place which uses the spidev
in this function, so replace it with netdev_err() to get rid of it. This
is done in preparation for unifying the KS8851 SPI and parallel drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ndev variable to netdev for the sake of consistency.
No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull out the spi->dev into one common place in the function instead of
having it repeated over and over again. This is done in preparation for
unifying ks8851 and ks8851-mll drivers. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ronak Doshi says:
====================
vmxnet3: upgrade to version 4
vmxnet3 emulation has recently added several new features which includes
offload support for tunnel packets, support for new commands the driver
can issue to emulation, change in descriptor fields, etc. This patch
series extends the vmxnet3 driver to leverage these new features.
Compatibility is maintained using existing vmxnet3 versioning mechanism as
follows:
- new features added to vmxnet3 emulation are associated with new vmxnet3
version viz. vmxnet3 version 4.
- emulation advertises all the versions it supports to the driver.
- during initialization, vmxnet3 driver picks the highest version number
supported by both the emulation and the driver and configures emulation
to run at that version.
In particular, following changes are introduced:
Patch 1:
This patch introduces utility macros for vmxnet3 version 4 comparison
and updates Copyright information.
Patch 2:
This patch implements get_rss_hash_opts and set_rss_hash_opts methods
to allow querying and configuring different Rx flow hash configurations
which can be used to support UDP/ESP RSS.
Patch 3:
This patch introduces segmentation and checksum offload support for
encapsulated packets. This avoids segmenting and calculating checksum
for each segment and hence gives performance boost.
Patch 4:
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
with this patch, the driver can configure emulation to run at vmxnet3
version 4.
Changes in v3 -> v4:
- Replaced BUG_ON() with WARN_ON_ONCE()
Changes in v2 -> v3:
- fixed get_rss_hash_opts to return correct values for udp rss
Changes in v2:
- Fixed compilation issue due to missing closed brace
- added fallthrough comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 4, provided
the emulation advertises support for version 4.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vmxnet3 version 3 device supports checksum/TSO offload. Thus, vNIC to
pNIC traffic can leverage hardware checksum/TSO offloads. However,
vmxnet3 does not support checksum/TSO offload for Geneve/VXLAN
encapsulated packets. Thus, for a vNIC configured with an overlay, the
guest stack must first segment the inner packet, compute the inner
checksum for each segment and encapsulate each segment before
transmitting the packet via the vNIC. This results in significant
performance penalty.
This patch will enhance vmxnet3 to support Geneve/VXLAN TSO as well as
checksum offload.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With vmxnet3 version 4, the emulation supports multiqueue(RSS) for
UDP and ESP traffic. A guest can enable/disable RSS for UDP/ESP over
IPv4/IPv6 by issuing commands introduced in this patch. ESP ipv6 is
not yet supported in this patch.
This patch implements get_rss_hash_opts and set_rss_hash_opts
methods to allow querying and configuring different Rx flow hash
configurations.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vmxnet3 is currently at version 3 and this patch initiates the
preparation to accommodate changes for version 4. Introduced utility
macros for vmxnet3 version 4 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A straightforward conversion of the ehci-mv binding to DT schema format
using json-schema.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[robh: add unevaluatedProperties]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
A straightforward conversion of the the spi-pxa2xx binding to DT schema
format using json-schema.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[robh: add unevaluatedProperties]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert the marvell,mmp2-ccic binding to DT schema format using
json-schema. While at that this drops the "func" and "phy" clocks.
The driver consumes clocks with those names, but it's not clear
what are they for and they are not used in DT systems. "phy" is
probably a clock for the sensor and it would belong in the sensor
node.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[robh: add additionalProperties]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The kbuild test robot is firing a warning over a missing prototype. The
function can just be static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
GCC warns about this comparison, which is unnecessary.
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert the i.MX thermal binding to DT schema format using json-schema
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Added a check such that only singleton IOMMU groups can pin pages.
>From the point when vendor driver pins any pages, consider IOMMU group
dirty page scope to be limited to pinned pages.
To optimize to avoid walking list often, added flag
pinned_page_dirty_scope to indicate if all of the vfio_groups for each
vfio_domain in the domain_list dirty page scope is limited to pinned
pages. This flag is updated on first pinned pages request for that IOMMU
group and on attaching/detaching group.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Added migration capability in IOMMU info chain.
User application should check IOMMU info chain for migration capability
to use dirty page tracking feature provided by kernel module.
User application must check page sizes supported and maximum dirty
bitmap size returned by this capability structure for ioctls used to get
dirty bitmap.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
DMA mapped pages, including those pinned by mdev vendor drivers, might
get unpinned and unmapped while migration is active and device is still
running. For example, in pre-copy phase while guest driver could access
those pages, host device or vendor driver can dirty these mapped pages.
Such pages should be marked dirty so as to maintain memory consistency
for a user making use of dirty page tracking.
To get bitmap during unmap, user should allocate memory for bitmap, set
it all zeros, set size of allocated memory, set page size to be
considered for bitmap and set flag VFIO_DMA_UNMAP_FLAG_GET_DIRTY_BITMAP.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
VFIO_IOMMU_DIRTY_PAGES ioctl performs three operations:
- Start dirty pages tracking while migration is active
- Stop dirty pages tracking.
- Get dirty pages bitmap. Its user space application's responsibility to
copy content of dirty pages from source to destination during migration.
To prevent DoS attack, memory for bitmap is allocated per vfio_dma
structure. Bitmap size is calculated considering smallest supported page
size. Bitmap is allocated for all vfio_dmas when dirty logging is enabled
Bitmap is populated for already pinned pages when bitmap is allocated for
a vfio_dma with the smallest supported page size. Update bitmap from
pinning functions when tracking is enabled. When user application queries
bitmap, check if requested page size is same as page size used to
populated bitmap. If it is equal, copy bitmap, but if not equal, return
error.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Fixed error reported by build bot by changing pgsize type from uint64_t
to size_t.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
IOMMU container maintains a list of all pages pinned by vfio_pin_pages API.
All pages pinned by vendor driver through this API should be considered as
dirty during migration. When container consists of IOMMU capable device and
all pages are pinned and mapped, then all pages are marked dirty.
Added support to start/stop dirtied pages tracking and to get bitmap of all
dirtied pages for requested IO virtual address range.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Calculate and cache pgsize_bitmap when iommu->domain_list is updated
and iommu->external_domain is set for mdev device.
Add iommu->lock protection when cached pgsize_bitmap is accessed.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
vfio_pfn.ref_count is always updated while holding iommu->lock, using
atomic variable is overkill.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
- Defined MIGRATION region type and sub-type.
- Defined vfio_device_migration_info structure which will be placed at the
0th offset of migration region to get/set VFIO device related
information. Defined members of structure and usage on read/write access.
- Defined device states and state transition details.
- Defined sequence to be followed while saving and resuming VFIO device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Convert the ingenic,jz4780-nand.txt doc file to ingenic,nand.yaml.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Convert the ingenic,jz4780-nemc.txt doc file to ingenic,nemc.yaml.
The ingenic,jz4725b-nemc compatible string was added in the process,
with a fallback to ingenic,jz4740-nemc.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
With 'commit 461c1a7d4733 ("gpiolib: override irq_enable/disable")' gpiolib
overrides irqchip's irq_enable and irq_disable callbacks. If irq_disable
callback is implemented then genirq takes unlazy path to disable irq.
Underlying irqchip may not want to implement irq_disable callback to lazy
disable irq when client drivers invokes disable_irq(). By overriding
irq_disable callback, gpiolib ends up always unlazy disabling IRQ.
Allow gpiolib to lazy disable IRQs by overriding irq_disable callback only
if irqchip implemented irq_disable. In cases where irq_disable is not
implemented irq_mask is overridden. Similarly override irq_enable callback
only if irqchip implemented irq_enable otherwise irq_unmask is overridden.
Fixes: 461c1a7d4733 ("gpiolib: override irq_enable/disable")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/1590253873-11556-2-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert the MXS GPIO binding to DT schema format using json-schema.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Document Device Tree bindings for the Renesas EMMA Mobile UART
Interface.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Convert the Renesas DDR Bus Controller Device Tree binding documentation
to json-schema.
Drop referrals to driver behavior.
Make power-domains required, as it is present for all current users.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
A generic GIC block embedded in an SoC may be connected to an on-SoC
reset controller. Hence allow the DTS writer to describe this relation,
by documenting the optional presence of a "reset" property.
This gets rid of "make dtbs_check" warnings like:
arch/arm/boot/dts/r8a7791-porter.dt.yaml: interrupt-controller@f1001000: 'resets' does not match any of the regexes: '^v2m@[0-9a-f]+$', 'pinctrl-[0-9]+'
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
|
