| Age | Commit message (Collapse) | Author |
|---|
|
Get rid of the local copies and pointers of intel_dp->DP and
instead just poke at it directly. Makes it much easier to see
where it actually gets used/modified.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Setting DP_PORT_EN in intel_dp->DP is already handled by
intel_dp_enable_port() so there is no point in setting it also
from the link training code.
For DDI platforms a bit with that name doesn't even exist. The
counterpart is DDI_BUF_CTL_ENABLE, which is already set up by
intel_ddi_prepare_link_retrain(). Fortunately it is the same bit
so there was no harm in doing this from the platform independent
code as well. But it's just confusing when platform independent
code sets platform specific bits in intel_dp->DP. Just get rid
of it.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak.intel.com>
|
|
I want intel_dp->DP to be fully populated by the time the
initial vswing programming happens. To that end move the
intel_ddi_init_dp_buf_reg() call to an earlier spot.
Additionally we don't want intel_ddi_init_dp_buf_reg() to
set DDI_BUF_CTL_ENABLE since the port should only get enabled
at the start of link training (see intel_ddi_prepare_link_retrain()).
So any earlier write to the register should not set the enable bit.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Currently we clear the leftover vswing/preemphasis values only
at the start of link training. That means the initial vswing
programming performed during modeset is going to use stale values
left over from the previous link training sequence, and then at
the start of link training we're going to reset the levels back
to 0. Seems much better to make sure we start with level 0 from
the get go.
Additionally if LTTPRs are present the leftover vswing/preemphasis
values are those of the last link in the chain, so not the values
that our PHY is even using after a successful link training sequence.
So let's make sure everything is cleared up before we start
programming anything.
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
With patch "drm/i915/vbt: Fix backlight parsing for VBT 234+"
the size of bdb_lfp_backlight_data structure has been increased,
causing if-statement in the parse_lfp_backlight function
that comapres this structure size to the one retrieved from BDB,
always to fail for older revisions.
This patch calculates expected size of the structure for a given
BDB version and compares it with the value gathered from BDB.
Tested on Chromebook Pixelbook (Nocturne) (reports bdb->version = 221)
Fixes: d381baad29b4 ("drm/i915/vbt: Fix backlight parsing for VBT 234+")
Tested-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134606.227234-1-lma@semihalf.com
|
|
PCI_DMA_BIDIRECTIONAL
Replace direction definition PCI_DMA_BIDIRECTIONAL
with DMA_BIDIRECTIONAL, because it helps to enhance readability
and avoid possible inconsistency.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210925124613.144-1-caihuoqing@baidu.com
|
|
If CONFIG_OF is disabled, devm_drm_of_get_bridge won't be compiled in
and drivers using that function will fail to build.
Add an inline stub so that we can still build-test those cases.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://patchwork.freedesktop.org/patch/msgid/20210928181333.1176840-1-maxime@cerno.tech
|
|
Ensure i915_vma_pin_iomap and vma_unpin are done with dpt->obj lock held.
I don't think there's much of a point in merging intel_dpt_pin() with
intel_pin_fb_obj_dpt(), they touch different objects.
Changes since v1:
- Fix using the wrong pointer to retrieve error code (Julia)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929085950.3063191-1-maarten.lankhorst@linux.intel.com
|
|
Let's not configure the single transcoder's TRANSCONF multiple
times with bigjoiner. No real harm I suppose but since we already
have the bigjoiner if statement directly above might as well suck
this in there and skip the redundant programming.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
|
|
Adjust the HSW+ transcoder state readout to just read through
all the possible transcoders for the pipe, and stuff the results
in a bitmask.
We can conveniently cross check the bitmask for invalid
combinations of enabled transcoders, and later we can easily
extend the bitmask readout to handle the bigjoiner case.
One slight change in behaviour is that we no longer read out
the AONOFF->force_pfit.pfit bit for all the enabled "panel
transcoders". But having more than one enabled would anyway
be illegal so no big loss. Also the AONOFF selection should
only ever be used on HSW, which only has the EDP transcoder
an no DSI transcoders.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-10-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
|
|
FBC+Yf tiling seems to work just fine, and unlike with linear
the hardware does appear to correctly calculate the CFB stride
with using the override stride on both cfl and glk. So no need
for any additional tweaks.
Cc: Uma Shankar <uma.shankar@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924141330.1515-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Stop using HBR2/3 support as a proxy for TPS3/4 support.
The two are no longer 1:1 in the hardware, arguably they
never were due to HSW ULX which does support TPS3 while
being limited to HBR1.
In more recent times GLK gained support for TPS4 while
being limited to HBR2. And on CNL+ some ports support
HBR3 while others are limited to HBR2, but all ports
support TPS4.
v2: s/INTEL_GEN/DISPLAY_VER/
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929162404.6717-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
We don't support dsi displays without a fixed mode, so drop
all the pointless checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
When using a panel with a fixed mode we don't change the refresh
rate of the display. Reject any user requested mode which doesn't
match that fixed refresh rate.
Unfortunately when Xorg sees the scaling_mode property on the
connecor it likes to automagically cook up modes whose refresh
rate is a fair bit off from the fixed refresh rate we use. So
we have to give it some extra latitude so that we don't start to
reject all of it.
v2: sDVO now uses intel_panel_compute_config() too
v3: Add a debug message to inform the user what happened
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929184536.8332-1-ville.syrjala@linux.intel.com
|
|
Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.
Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.
v2: Use intel_panel_compute_config() with sDVO
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
When using a fixed mode we won't change the refresh rate ever.
So filter out all modes that don't match the fixed_mode's refresh
rate.
I'm going to declare the "rounded to nearest Hz refresh
rates must match" approach good enough for now.
Note that we could start supporting multiple refresh rates
with panels that can do it, but that would mean replacing
the single fixed mode concept with a list of fixed modes.
Then we could look for the closest match to the user's
requested refresh rate and use that. But all of that would
be a fair bit of work so we'll leave it for later.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
All fixed mode panels should behave the same way when it comes to mode
filtering. Reuse the intel_panel_mode_valid() for all of them.
This changes the behaviour to match what we do for eDP, ie.
reject anything that doesn't exactly match the fixed mode
dimensions. Users can still manually provide different
sized modes which will be handled by the panel fitter just
as before. The difference is that we can no longer report
funny modes in the connector's mode list.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Extract intel_panel_mode_valid() from the eDP code to a generic helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch is to add cyan_skillfish asic header files.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To support libdrm tests.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Handle all DMA IOMMU group related dependencies before the
group is removed and we try to access it after free.
v2:
Move the actul handling function to TTM
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We use the number_instance index that we get from the fw discovery blob
to index into an array for example.
Update error messages (Alex)
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The two AMD drivers have their own custom offsetof() implementation
that now triggers a warning with recent versions of clang:
drivers/gpu/drm/radeon/radeon_atombios.c:133:14: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
Change all the instances to use the normal offsetof() provided
by the kernel that does not have this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use resource_size function on resource object
instead of explicit computation.
Clean up coccicheck warning:
./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:905:10-13: ERROR: Missing
resource_size with res
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The overflow check in amdgpu_bo_list_create() causes a warning with
clang-14 on 64-bit architectures, since the limit can never be
exceeded.
drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:74:18: error: result of comparison of constant 256204778801521549 with expression of type 'unsigned int' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (num_entries > (SIZE_MAX - sizeof(struct amdgpu_bo_list))
~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The check remains useful for 32-bit architectures, so just avoid the
warning by using size_t as the type for the count.
Fixes: 920990cb080a ("drm/amdgpu: allocate the bo_list array after the list")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GFX9+, format modifiers are always enabled and ensure the
frame-buffers can be scanned out at ADDFB2 time.
On GFX8-, format modifiers are not supported and no other check
is performed. This means ADDFB2 IOCTLs will succeed even if the
tiling isn't supported for scan-out, and will result in garbage
displayed on screen [1].
Fix this by adding a check for tiling flags for GFX8 and older.
The check is taken from radeonsi in Mesa (see how is_displayable
is populated in gfx6_compute_surface).
Changes in v2: use drm_WARN_ONCE instead of drm_WARN (Michel)
[1]: https://github.com/swaywm/wlroots/issues/3185
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Michel Dänzer <mdaenzer@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The commit 2766534b766e1b12e0fa0a4e2e26929e808fde71 added the offset
header but didn't add the masks. This adds the masks based on what
was selected for the offsets.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path
[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Recently debugging efforts have involved setting/checking the
X.Y value used during payload allocation. Current output for
Y was calculated with incorrect bitshift. Y value is also not
human readable.
[How]
Refactor logging into separate function. Fix Y calculation error
and format output to be human readable.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why/How]
Theoretically rare corner case where ceil(Y) results in rounding
up to an integer. If this happens, the 1 should be carried over to
the X value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
There is a chance verified link cap can be greater than max link cap.
This causes software hang because we cannot power up PHY with link rate
that cannot handle.
The change is to guard verfieid link cap from becoming larger than max link cap
our PHy can support.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data
[How]
Initialize the variable to false
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The PHY ownership release->AUX PW disable steps during a modeset
disable->PHY disconnect sequence can hang the system if the PHY
disconnect happens after disabling the PHY's PLL. The spec doesn't
require a specific order for these two steps, so this issue is still
being root caused by HW/FW teams. Until that is found, let's make
sure the disconnect happens before the PLL is disabled, and do this on
all platforms for consistency.
v2: Add a TODO comment to remove the w/a once the issue is root
caused/fixed. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-7-imre.deak@intel.com
|
|
After the previous patch the driver holds a power domain blocking
TC-cold whenever the port is locked, so we can remove the extra blocking
around the lock/unlock sequence.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-13-imre.deak@intel.com
|
|
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
|
|
While a TypeC port mode is locked a DISPLAY_CORE power domain reference
is held, which implies a runtime PM ref. By removing the ICL !legacy
port special casing, a TC_COLD_OFF power domain reference will be taken
for such ports, which also translates to a runtime PM ref on that
platform. A follow-up change will stop holding the DISPLAY_CORE power
domain while the port is locked.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-11-imre.deak@intel.com
|
|
For the ADL-P TBT mode the spec doesn't require blocking TC-cold by
using the legacy AUX power domain. To avoid the timeouts that this would
cause during PHY disconnect/reconnect sequences (which will be more
frequent after a follow-up change) use the TC_COLD_OFF power domain in
TBT mode on all platforms. On TGL this power domain blocks TC-cold via a
PUNIT command, while on other platforms the domain just takes a runtime
PM reference.
If the HPD live status indicates that the port mode needs to be reset
- for instance after switching from TBT to a DP-alt sink - still take
the AUX domain, since the IOM firmware handshake requires this.
v2: Rebased on v2 of the previous patch.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-5-imre.deak@intel.com
|
|
A follow-up change will select the TC-cold blocking power domain based
on the TypeC mode, prepare for that here.
Also bring intel_tc_cold_requires_aux_pw() earlier to its logical place
for readability.
No functional change.
v2: Add code comment about IOM reg accesses in TCCOLD. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-4-imre.deak@intel.com
|
|
A follow-up change will start to disconnect/re-connect PHYs around AUX
transfers and modeset enable/disables. To prepare for that add a new
TypeC PHY disconnected mode, to help tracking the TC-cold blocking power
domain status (no power domain in disconnected state, mode dependent
power domain in connected state).
v2: Move the !disconnected mode and phy-owned asserts in
__intel_tc_port_lock() later in the patchset, when the asserts will
hold. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-3-imre.deak@intel.com
|
|
A follow-up patch will disconnect/reconnect PHYs around AUX transfers
and modeset enable/disables. To prepare for that and make things
consistent for all TypeC modes stop connecting the PHY in legacy mode
without a sink being connected. This was done before since in legacy
mode the PHY is dedicated to display usage, so there was no point in
disconnecting it. However after the follow-up changes the TC-cold
blocking power domains will be held as long as the PHY is in the
connected state, so we'll need to disconnect/re-connect the PHY in all
TypeC modes to allow for power saving.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-7-imre.deak@intel.com
|
|
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
|
|
On ADL-P the PHY ready/complete flag is always set even in TBT-alt mode.
To avoid taking the PHY ownership and the following spurious "PHY sudden
disconnect" messages on this platform when connecting the PHY in TBT
mode, check if there is any DP-alt or legacy sink connected before
taking the ownership.
v2: (Jose)
- Fix debug message clarifying that a TBT sink can be connected.
- Add comments describing the PHY complete HW flag semantic differences
between adl-p and other platforms.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-2-imre.deak@intel.com
|
|
Waiting for the PHY complete flag to clear when releasing the PHY
ownership was add in
commit ddec362724f9 ("drm/i915: Wait for TypeC PHY complete flag to clear in safe mode")
This isn't required by the spec, the vague idea was to make the
handshake with the firmware more robust, without actual evidence for
when it would be needed. Checking this again, the flag doesn't clear on
ICL until after the PHY's PLL is disabled and the flag is permanently
set on ADL-P. To avoid the spurious timeout messages in dmesg, just
remove this wait.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-4-imre.deak@intel.com
|
|
On ADL-P the PHY ready (aka status complete on other platforms) flag is
always set, besides when a DP-alt, legacy sink is connected also when a
TBT sink is connected or nothing is connected. So assume the PHY to be
connected when both the TBT live status and PHY ready flags are set.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-3-imre.deak@intel.com
|
|
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68d3 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
|
|
Display underrun in HDR mode when cursor is enabled.
RTL fix will be implemented CLKGATE_DIS_PSL_A bit 28-46520h.
As per W/A 1604331009, Disable cursor clock gating in HDR mode.
Bspec : 33451
Changes since V6:
- Address checkpatch warnings
- Bit ordering
Changes since V5:
- replace intel_de_read with intel_de_rmw - Jani
Changes since V4:
- Added WA needed check - Ville
- Replace BIT with REG_BIT - Ville
- Add WA enable/disable support back which was
added in V1 - Ville
Changes since V3:
- Disable WA when not in HDR mode or cursor plane
not active - Ville
- Extract required args from crtc_state - Ville
- Create HDR mode API using bdw_set_pipemisc ref - Ville
- Tested with HDR video as well full setmode, WA
applies and disables
Changes since V2:
- Made it general gen11 WA
- Removed WA needed check
- Added cursor plane active check
- Once WA enable, software will not disable
Changes since V1:
- Modified way CLKGATE_DIS_PSL bit 28 was modified
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929052442.2543054-1-tejaskumarx.surendrakumar.upadhyay@intel.com
|
|
In commit:
commit 667a50db0477d47fdff01c666f5ee1ce26b5264c
Author: Thomas Hellstrom <thellstrom@vmware.com>
Date: Fri Jan 3 11:17:18 2014 +0100
drm/ttm: Refuse to fault (prime-) imported pages
we introduced the restriction that imported pages should not be directly
mappable through TTM(this also extends to userptr). In the next patch we
want to introduce a shmem_tt backend, which should follow all the
existing rules with TTM_PAGE_FLAG_EXTERNAL, since it will need to handle
swapping itself, but with the above mapping restriction lifted.
v2(Christian):
- Don't OR together EXTERNAL and EXTERNAL_MAPPABLE in the definition
of EXTERNAL_MAPPABLE, just leave it the caller to handle this
correctly, otherwise we might encounter subtle issues.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132629.353541-3-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
Move it to inline kernel-doc, otherwise we can't add empty lines it
seems. Also drop the kernel-doc for pages_list, which doesn't seem to
exist.
v2(Christian):
- Add a note that FLAG_SWAPPED shouldn't need to be touched by drivers.
- Mention what FLAG_POPULATED does.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132629.353541-2-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
It covers more than just ttm_bo_type_sg usage, like with say dma-buf,
since one other user is userptr in amdgpu, and in the future we might
have some more. Hence EXTERNAL is likely a more suitable name.
v2(Christian):
- Rename these to TTM_TT_FLAGS_*
- Fix up all the holes in the flag values
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132629.353541-1-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
