| Age | Commit message (Collapse) | Author |
|---|
|
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
|
|
result is always zero when comes here.
Signed-off-by: Yao Dongdong <yaodongdong@huawei.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
When a subdriver is rmmod-ed then re-insmod-ed, the hid device is not
destroyed as it is owned by the transport layer.
So when we re-probed the device, the hid device is assumed to be already
claimed, and can lead to page faults if hid-core tries to forward the
emitted data to the to-be-created claimed node.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
Just wiring up the bpf system call.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up bpf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
|
|
Tracing for a workload begins before the comm event is seen, which
results in the initial comm having a string of the form ":<pid>" (e.g.
":12345").
In order to export the correct string, defer the export until the new
script 'flush' callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-8-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add the ability to export detailed information about paired calls and
returns to Python db export and the export-to-postgresql.py script.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-7-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Make it possible for the database export API to use the enhanced thread
stack and export detailed information about paired calls and returns.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-6-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add branch_type and in_tx to Python db export and the
export-to-postgresql.py script.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-4-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add the ability to export branch types through the database export
facility.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds CONFIG_X86_VSYSCALL_EMULATION, guarded by CONFIG_EXPERT.
Turning it off completely disables vsyscall emulation, saving ~3.5k
for vsyscall_64.c, 4k for vsyscall_emu_64.S (the fake vsyscall
page), some tiny amount of core mm code that supports a gate area,
and possibly 4k for a wasted pagetable. The latter is because the
vsyscall addresses are misaligned and fit poorly in the fixmap.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/406db88b8dd5f0cbbf38216d11be34bbb43c7eae.1414618407.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
vsyscall_64.c is just vsyscall emulation. Tidy it up accordingly.
[ tglx: Preserved the original copyright notices ]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/9c448d5643d0fdb618f8cde9a54c21d2bcd486ce.1414618407.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
I see no point in having an unusable read-only page sitting at
0xffffffffff600000 when vsyscall=none. Instead, skip mapping it and
remove it from /proc/PID/maps.
I kept the ratelimited warning when programs try to use a vsyscall
in this mode, since it may help admins avoid confusion.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/0dddbadc1d4e3bfbaf887938ff42afc97a7cc1f2.1414618407.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Enhance the thread stack to output detailed information about paired
calls and returns.
The enhanced processing consumes sample information via
thread_stack__process() and outputs information about paired calls /
returns via a call-back.
While the call-back makes it possible for the facility to be used by
arbitrary tools, a subsequent patch will provide the information to
Python scripting via the db-export interface.
An important part of the call/return information is the
call path which provides a structure that defines a context
sensitive call graph.
Note that there are now two ways to use the thread stack.
For simply providing a call stack (like you would get from the perf
record -g option) the interface consists of thread_stack__event() and
thread_stack__sample().
Whereas the enhanced interface consists of call_return_processor__new()
and thread_stack__process().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-5-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Steffen Klassert says:
====================
ipv6: Fix iflink setting for ipv6 tunnels
The ipv6 tunnels do the dev->iflink setting too early, it gets
overwritten by register_netdev(). So set dev->iflink from within
a ndo_init function to keep the configured setting.
This patchset fixes this for ip6_tunnel, vti6, sit and gre6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipip6_tunnel_init() sets the dev->iflink via a call to
ipip6_tunnel_bind_dev(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the
ndo_init function. Then ipip6_tunnel_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vti6_dev_init() sets the dev->iflink via a call to
vti6_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for vti6 tunnels. Fix this by using vti6_dev_init() as the
ndo_init function. Then vti6_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a thread stack for synthesizing call chains from call and return
events.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1414678188-14946-2-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4f5 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On i.MX6SX sdb platform, there has two same enet MACs, after system up,
just eth0 is up, and then do suspend/resume test:
[ 50.437967] PM: Syncing filesystems ... done.
[ 50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done.
[ 50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done.
[ 50.559771] ------------[ cut here ]------------
[ 50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c()
[ 50.572475] Modules linked in:
[ 50.575578] CPU: 0 PID: 575 Comm: sh Not tainted 3.18.0-rc2-next-20141031-00007-gf61135b #21
[ 50.584031] Backtrace:
[ 50.586550] [<80011ecc>] (dump_backtrace) from [<8001206c>] (show_stack+0x18/0x1c)
[ 50.594136] r6:808a7a54 r5:00000000 r4:00000000 r3:00000000
[ 50.599920] [<80012054>] (show_stack) from [<806ab3c0>] (dump_stack+0x80/0x9c)
[ 50.607187] [<806ab340>] (dump_stack) from [<8002a3e8>] (warn_slowpath_common+0x6c/0x8c)
[ 50.615294] r5:00000353 r4:00000000
[ 50.618940] [<8002a37c>] (warn_slowpath_common) from [<8002a42c>] (warn_slowpath_null+0x24/0x2c)
[ 50.627738] r8:00000000 r7:be144c44 r6:be015600 r5:80070013 r4:be015600
[ 50.634573] [<8002a408>] (warn_slowpath_null) from [<804f8d4c>] (__clk_disable+0x60/0x6c)
[ 50.642777] [<804f8cec>] (__clk_disable) from [<804f8e5c>] (clk_disable+0x2c/0x38)
[ 50.650359] r4:be015600 r3:00000000
[ 50.654006] [<804f8e30>] (clk_disable) from [<80420ab4>] (fec_enet_clk_enable+0xc4/0x258)
[ 50.662196] r5:be3cb620 r4:be3cb000
[ 50.665838] [<804209f0>] (fec_enet_clk_enable) from [<80421178>] (fec_suspend+0x30/0x180)
[ 50.674026] r7:be144c44 r6:be144c10 r5:8037f5a4 r4:be3cb000
[ 50.679802] [<80421148>] (fec_suspend) from [<8037f5d8>] (platform_pm_suspend+0x34/0x64)
[ 50.687906] r10:00000000 r9:00000000 r8:00000000 r7:be144c44 r6:be144c10 r5:8037f5a4
[ 50.695852] r4:be144c10 r3:80421148
[ 50.699511] [<8037f5a4>] (platform_pm_suspend) from [<8038784c>] (dpm_run_callback.isra.14+0x34/0x6c)
[ 50.708764] [<80387818>] (dpm_run_callback.isra.14) from [<80387f00>] (__device_suspend+0x12c/0x2a4)
[ 50.717909] r9:8098ec8c r8:80973bec r6:00000002 r5:811c7038 r4:be144c10
[ 50.724746] [<80387dd4>] (__device_suspend) from [<803894fc>] (dpm_suspend+0x64/0x224)
[ 50.732675] r8:80973bec r7:be144c10 r6:8098ec24 r5:811c7038 r4:be144cc4
[ 50.739509] [<80389498>] (dpm_suspend) from [<8038999c>] (dpm_suspend_start+0x60/0x68)
[ 50.747438] r10:8082fa24 r9:00000000 r8:00000004 r7:00000003 r6:00000000 r5:8116ec80
[ 50.755386] r4:00000002
[ 50.757969] [<8038993c>] (dpm_suspend_start) from [<800679d8>] (suspend_devices_and_enter+0x90/0x3ec)
[ 50.767202] r4:00000003 r3:8116eca0
[ 50.770843] [<80067948>] (suspend_devices_and_enter) from [<80067f40>] (pm_suspend+0x20c/0x2a4)
[ 50.779553] r8:00000004 r7:00000003 r6:00000000 r5:8116ec8c r4:00000003
[ 50.786394] [<80067d34>] (pm_suspend) from [<80066858>] (state_store+0x70/0xc0)
[ 50.793718] r6:8116ec90 r5:00000003 r4:bd88a800 r3:0000006d
[ 50.799496] [<800667e8>] (state_store) from [<802b0384>] (kobj_attr_store+0x1c/0x28)
[ 50.807251] r10:bd399f78 r8:00000000 r7:bd88a800 r6:bd88a800 r5:00000004 r4:bd085680
[ 50.815219] [<802b0368>] (kobj_attr_store) from [<80153090>] (sysfs_kf_write+0x54/0x58)
[ 50.823252] [<8015303c>] (sysfs_kf_write) from [<80151fd8>] (kernfs_fop_write+0xd0/0x194)
[ 50.831441] r6:00000004 r5:bd08568c r4:bd085680 r3:8015303c
[ 50.837220] [<80151f08>] (kernfs_fop_write) from [<800eddb4>] (vfs_write+0xb8/0x1a8)
[ 50.844975] r10:00000000 r9:00000000 r8:00000000 r7:bd399f78 r6:01336408 r5:00000004
[ 50.852924] r4:bc584dc0
[ 50.855505] [<800edcfc>] (vfs_write) from [<800ee0b8>] (SyS_write+0x48/0x88)
[ 50.862567] r10:00000000 r8:00000000 r7:01336408 r6:00000004 r5:bc584dc0 r4:bc584dc0
[ 50.870537] [<800ee070>] (SyS_write) from [<8000eb00>] (ret_fast_syscall+0x0/0x48)
[ 50.878120] r9:bd398000 r8:8000ecc4 r7:00000004 r6:76f42b48 r5:01336408 r4:00000004
[ 50.885983] ---[ end trace 7545115d752a316a ]---
[ 50.890765] ------------[ cut here ]------------
The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still
call .fec_enet_clk_enable() to disable clock.
To avoid the broken, let it check network device up status by calling .netif_running()
before disable/enable clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Herbert Xu says:
====================
tun: Fix csum_start and TUN_PKT_STRIP
The first patch fixes a serious problem that breaks checksum offload
in VMs while the second patch fixes a problem that probably affects
no one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place. The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.
Fixes: 6680ec68eff4 ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we run out of blocks for a given multi-block allocation, we obviously
did not reserve enough. We should reserve more blocks for the next
reservation to reduce fragmentation. This patch increases the size hint
for reservations when they run out.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
If an application does a sequence of (1) big write, (2) little write
we don't necessarily want to reset the size hint based on the smaller
size. The fact that they did any big writes implies they may do more,
and therefore we should try to allocate bigger block reservations, even
if the last few were small writes. Therefore this patch changes function
gfs2_size_hint so that the size hint can only grow; it cannot shrink.
This is especially important where there are multiple writers.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This patch tries to use the journal numbers to evenly distribute
which node prefers which resource group for block allocations. This
is to help performance.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
No need to store gfs2_dir_check result and test it before returning.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
* report the fixed per-transponder symbolrate instead of per-TS ones
* add output TS-ID report
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
list_for_each_entry_safe() is necessary if list objects are deleted from
the list while traversing it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Remove legacy support for at91sam9rl boards.
This include board files removal plus all legacy code for non DT boards
support.
Use the Device Tree for running this board with newer kernels.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: Add sentence about DT]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Remove legacy support for at91sam9g45/9m10 boards.
This include board files removal plus all legacy code for non DT boards
support (i.e. at91sam9g45.c and at91sam9g45_devices.c).
Use the Device Tree for running this board with newer kernels.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: Add sentence about DT, removed defconfig]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
As there is currently no-one to take care of this old !MMU target and as its
support in recent kernels is a bit rotten, remove this at91x40 support and the
board file associated with it (at91eb01).
There are modern ARM !MMU in Mainline now so this target is not interesting for
building tests anymore. It would be better to start from these modern ARM !MMU
platforms to reintroduce at91x40 support if needed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
The makefile for sanitizing kernel headers uses the kbuild file
to determine which files to do. Several networking related headers
were missing. Without these headers iproute2 build would break.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
error: implicit declaration of function 'csum_ipv6_magic'
csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1
Seen with powerpc:allmodconfig.
Fixes: 523b929d5446 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
All function dealing with operating modes use unsigned int for modes
so change max77802_map_mode() function signature for consistency.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
