| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.5, 2nd round:
- Fix i.MX93 ANATOP 'reg' resource size to avoid overlapping with TMU
memory area.
- Fix RTC interrupt level on imx6qdl-phytec-mira board.
- Remove LDB endpoint from from the common imx6sx.dtsi as it causes
regression for boards that has the LCDIF connected directly to
a parallel display.
- Drop CSI1 PHY reference clock configuration from i.MX8MM/N device tree
to avoid overclocking.
- Set a proper default tuning step for i.MX6SX and i.MX7D uSDHC to fix
a tuning failure seen with some SD cards.
* tag 'imx-fixes-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx93: Fix anatop node size
ARM: dts: imx: Set default tuning step for imx6sx usdhc
arm64: dts: imx8mm: Drop CSI1 PHY reference clock configuration
arm64: dts: imx8mn: Drop CSI1 PHY reference clock configuration
ARM: dts: imx: Set default tuning step for imx7d usdhc
ARM: dts: imx6: phytec: fix RTC interrupt level
ARM: dts: imx6sx: Remove LDB endpoint
Link: https://lore.kernel.org/r/20230809100034.GS151430@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm irq fixes from Jarkko Sakkinen:
"These change the probing and enabling of interrupts advertised by the
platform firmware (i.e. ACPI, Device Tree) to be an opt-in for tpm_tis,
which can be set from the kernel command-line.
Note that the opt-in change is only for the PC MMIO tpm_tis module. It
does not affect other similar drivers using IRQs, like tpm_tis_spi and
synquacer"
* tag 'tpmdd-v6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm_tis: Opt-in interrupts
tpm: tpm_tis: Fix UPX-i11 DMI_MATCH condition
|
|
Pull rdma fixes from Jason Gunthorpe:
"A few small bugs:
- Fix longstanding mlx5 bug where ODP would fail with certain MR
alignments
- cancel work to prevent a hfi1 UAF
- MAINTAINERS update
- UAF, missing mutex_init and an error unwind bug in bnxt_re"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/bnxt_re: Initialize dpi_tbl_lock mutex
RDMA/bnxt_re: Fix error handling in probe failure path
RDMA/bnxt_re: Properly order ib_device_unalloc() to avoid UAF
MAINTAINERS: Remove maintainer of HiSilicon RoCE
IB/hfi1: Fix possible panic during hotplug remove
RDMA/umem: Set iova in ODP flow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fix from Damien Le Moal:
- The switch to using iomap for executing a direct synchronous write to
sequential files using a zone append BIO overlooked cases where the
BIO built by iomap is too large and needs splitting, which is not
allowed with zone append.
Fix this by using regular write commands instead. The use of zone
append commands will be reintroduced later with proper support from
iomap.
* tag 'zonefs-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: fix synchronous direct writes to sequential files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix sporadic comunication errors in pmbus/bel-pfe and
aquacomputer_d5next drivers
* tag 'hwmon-for-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (aquacomputer_d5next) Add selective 200ms delay after sending ctrl report
hwmon: (pmbus/bel-pfe) Enable PMBUS_SKIP_STATUS_CHECK for pfe1100
|
|
Cc: stable@vger.kernel.org # v6.4+
Link: https://lore.kernel.org/linux-integrity/CAHk-=whRVp4h8uWOX1YO+Y99+44u4s=XxMK4v00B6F1mOfqPLg@mail.gmail.com/
Fixes: e644b2f498d2 ("tpm, tpm_tis: Enable interrupt test")
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The patch which made it to the kernel somehow changed the
match condition from
DMI_MATCH(DMI_PRODUCT_NAME, "UPX-TGL01")
to
DMI_MATCH(DMI_PRODUCT_VERSION, "UPX-TGL")
Revert back to the correct match condition to disable the
interrupt mode on the board.
Cc: stable@vger.kernel.org # v6.4+
Fixes: edb13d7bb034 ("tpm: tpm_tis: Disable interrupts *only* for AEON UPX-i11")
Link: https://lore.kernel.org/lkml/20230524085844.11580-1-peter.ujfalusi@linux.intel.com/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"14 hotfixes. 11 of these are cc:stable and the remainder address
post-6.4 issues, or are not considered suitable for -stable
backporting"
* tag 'mm-hotfixes-stable-2023-08-11-13-44' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/damon/core: initialize damo_filter->list from damos_new_filter()
nilfs2: fix use-after-free of nilfs_root in dirtying inodes via iput
selftests: cgroup: fix test_kmem_basic false positives
fs/proc/kcore: reinstate bounce buffer for KCORE_TEXT regions
MAINTAINERS: add maple tree mailing list
mm: compaction: fix endless looping over same migrate block
selftests: mm: ksm: fix incorrect evaluation of parameter
hugetlb: do not clear hugetlb dtor until allocating vmemmap
mm: memory-failure: avoid false hwpoison page mapped error info
mm: memory-failure: fix potential unexpected return value from unpoison_memory()
mm/swapfile: fix wrong swap entry type for hwpoisoned swapcache page
radix tree test suite: fix incorrect allocation size for pthreads
crypto, cifs: fix error handling in extract_iter_to_sg()
zsmalloc: fix races between modifications of fullness and isolated
|
|
Commit
522b1d69219d ("x86/cpu/amd: Add a Zenbleed fix")
provided a fix for the Zen2 VZEROUPPER data corruption bug affecting
a range of CPU models, but the AMD Custom APU 0405 found on SteamDeck
was not listed, although it is clearly affected by the vulnerability.
Add this CPU variant to the Zenbleed erratum list, in order to
unconditionally enable the fallback fix until a proper microcode update
is available.
Fixes: 522b1d69219d ("x86/cpu/amd: Add a Zenbleed fix")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230811203705.1699914-1-cristian.ciocaltea@collabora.com
|
|
The WinSystems WS16C48 I/O address region spans offsets 0x0 through 0xA,
which is a total of 11 bytes. Fix the WS16C48_EXTENT define to the
correct value of 11 so that access to necessary device registers is
properly requested in the ws16c48_probe() callback by the
devm_request_region() function call.
Fixes: 2c05a0f29f41 ("gpio: ws16c48: Implement and utilize register structures")
Cc: stable@vger.kernel.org
Cc: Paul Demetrotion <pdemetrotion@winsystems.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Rework the handling of interrupt overrides on AMD Zen-based machines
to avoid recently introduced regressions (Hans de Goede).
Note that this is intended as a short-term mitigation for 6.5 and the
long-term approach will be to attempt to use the configuration left by
the BIOS, but it requires more investigation"
* tag 'acpi-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Add IRQ override quirk for PCSpecialist Elimina Pro 16 M
ACPI: resource: Honor MADT INT_SRC_OVR settings for IRQ1 on AMD Zen
ACPI: resource: Always use MADT override IRQ settings for all legacy non i8042 IRQs
ACPI: resource: revert "Remove "Zen" specific match and quirks"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an amd-pstate cpufreq driver issues and recently introduced
hibernation-related breakage.
Specifics:
- Make amd-pstate use device_attributes as expected by the CPU root
kobject (Thomas Weißschuh)
- Restore the previous behavior of resume_store() when hibernation is
not available which is to return the full number of bytes that were
to be written by user space (Vlastimil Babka)"
* tag 'pm-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: amd-pstate: fix global sysfs attribute type
PM: hibernate: fix resume_store() return value when hibernation not available
|
|
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d83767c ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3f4 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 9b9c8195f3f0 ("tty: n_gsm: fix UAF in gsm_cleanup_mux"), the UAF
problem is not completely fixed. There is a race condition in
gsm_cleanup_mux(), which caused this UAF.
The UAF problem is triggered by the following race:
task[5046] task[5054]
----------------------- -----------------------
gsm_cleanup_mux();
dlci = gsm->dlci[0];
mutex_lock(&gsm->mutex);
gsm_cleanup_mux();
dlci = gsm->dlci[0]; //Didn't take the lock
gsm_dlci_release(gsm->dlci[i]);
gsm->dlci[i] = NULL;
mutex_unlock(&gsm->mutex);
mutex_lock(&gsm->mutex);
dlci->dead = true; //UAF
Fix it by assigning values after mutex_lock().
Link: https://syzkaller.appspot.com/text?tag=CrashReport&x=176188b5a80000
Cc: stable <stable@kernel.org>
Fixes: 9b9c8195f3f0 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Fixes: aa371e96f05d ("tty: n_gsm: fix restart handling via CLD command")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Signed-off-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Link: https://lore.kernel.org/r/20230811031121.153237-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fixes for request_queue state (Ming)
- Another uuid quirk (August)
- RCU poll fix for NVMe (Ming)
- Fix for an IO stall with polled IO (me)
- Fix for blk-iocost stats enable/disable accounting (Chengming)
- Regression fix for large pages for zram (Christoph)
* tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux:
nvme: core: don't hold rcu read lock in nvme_ns_chr_uring_cmd_iopoll
blk-iocost: fix queue stats accounting
block: don't make REQ_POLLED imply REQ_NOWAIT
block: get rid of unused plug->nowait flag
zram: take device and not only bvec offset into account
nvme-pci: add NVME_QUIRK_BOGUS_NID for Samsung PM9B1 256G and 512G
nvme-rdma: fix potential unbalanced freeze & unfreeze
nvme-tcp: fix potential unbalanced freeze & unfreeze
nvme: fix possible hang when removing a controller during error recovery
|
|
Pull io_uring fixes from Jens Axboe:
"A followup fix for the parisc/SHM_COLOUR fix, also from Helge, which
is heading to stable.
And then just the io_uring equivalent of the RESOLVE_CACHED fix in
commit a0fc452a5d7f from last week for build_open_flags()"
* tag 'io_uring-6.5-2023-08-11' of git://git.kernel.dk/linux:
io_uring/parisc: Adjust pgoff in io_uring mmap() for parisc
io_uring: correct check for O_TMPFILE
|
|
In
6524c798b727 ("driver core: cpu: Make cpu_show_not_affected() static")
I fat-fingered the name of cpu_show_gds(). Usually, I'd rebase but since
those are extraordinary embargoed times, the commit above was already
pulled into another tree so no no.
Therefore, fix it ontop.
Fixes: 6524c798b727 ("driver core: cpu: Make cpu_show_not_affected() static")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230811095831.27513-1-bp@alien8.de
|
|
Merge a cpufreq fix for 6.5-rc6.
This makes amd-pstate use device_attributes as expected by the CPU root
kobject.
* pm-cpufreq:
cpufreq: amd-pstate: fix global sysfs attribute type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Add Manivannan Sadhasivam as DesignWare PCIe driver co-maintainer
(Krzysztof Wilczyński)
- Revert "PCI: dwc: Wait for link up only if link is started" to fix a
regression on Qualcomm platforms that don't reach interconnect sync
state if the slot is empty (Johan Hovold)
- Revert "PCI: mvebu: Mark driver as BROKEN" so people can use
pci-mvebu even though some others report problems (Bjorn Helgaas)
- Avoid a NULL pointer dereference when using acpiphp for root bus
hotplug to fix a regression added in v6.5-rc1 (Igor Mammedov)
* tag 'pci-v6.5-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus
Revert "PCI: mvebu: Mark driver as BROKEN"
Revert "PCI: dwc: Wait for link up only if link is started"
MAINTAINERS: Add Manivannan Sadhasivam as DesignWare PCIe driver maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- Fixes for a pair of kexec_file_load() failures
- A fix to ensure the direct mapping is PMD-aligned
- A fix for CPU feature detection on SMP=n
- The MMIO ordering fences have been strengthened to ensure ordering
WRT delay()
- Fixes for a pair of -Wmissing-variable-declarations warnings
- A fix to avoid PUD mappings in vmap on sv39
- flush_cache_vmap() now flushes the TLB to avoid issues on systems
that cache invalid mappings
* tag 'riscv-for-linus-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Implement flush_cache_vmap()
riscv: Do not allow vmap pud mappings for 3-level page table
riscv: mm: fix 2 instances of -Wmissing-variable-declarations
riscv,mmio: Fix readX()-to-delay() ordering
riscv: Fix CPU feature detection with SMP disabled
riscv: Start of DRAM should at least be aligned on PMD size for the direct mapping
riscv/kexec: load initrd high in available memory
riscv/kexec: handle R_RISCV_CALL_PLT relocation type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"A bugfix in the LWS code, which used different lock words than the
parisc lightweight spinlock checks. This inconsistency triggered false
positives when the lightweight spinlock checks checked the locks of
mutexes.
The other patches are trivial cleanups and most of them fix sparse
warnings.
Summary:
- Fix LWS code to use same lock words as for the parisc lightweight
spinlocks
- Use PTR_ERR_OR_ZERO() in pdt init code
- Fix lots of sparse warnings"
* tag 'parisc-for-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: perf: Make cpu_device variable static
parisc: ftrace: Add declaration for ftrace_function_trampoline()
parisc: boot: Nuke some sparse warnings in decompressor
parisc: processor: Include asm/smp.h for init_per_cpu()
parisc: unaligned: Include linux/sysctl.h for unaligned_enabled
parisc: Move proc_mckinley_root and proc_runway_root to sba_iommu
parisc: dma: Add prototype for pcxl_dma_start
parisc: parisc_ksyms: Include libgcc.h for libgcc prototypes
parisc: ucmpdi2: Fix no previous prototype for '__ucmpdi2' warning
parisc: firmware: Mark pdc_result buffers local
parisc: firmware: Fix sparse context imbalance warnings
parisc: signal: Fix sparse incorrect type in assignment warning
parisc: ioremap: Fix sparse warnings
parisc: fault: Use C99 arrary initializers
parisc: pdt: Use PTR_ERR_OR_ZERO() to simplify code
parisc: Fix lightweight spinlock checks to not break futexes
|
|
Mike Travis has retired. His expertise will be sorely missed.
Remove Mike's entry under SGI XP/XPC/XPNET DRIVER.
Replace Mike's entry under UV HPE SUPERDOME FLEX.
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Joel Granados <j.granados@samsung.com>
Link: https://lore.kernel.org/all/20230801155756.22308-1-justin.ernst%40hpe.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull cpuidle psci fixes from Ulf Hansson:
"A couple of cpuidle-psci fixes. Usually, this is managed by arm-soc
maintainers or Rafael, although due to a busy period I have stepped in
to help out:
- Fix the error path to prevent reverting from OSI back to PC mode"
* tag 'cpuidle-psci-v6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
cpuidle: psci: Move enabling OSI mode after power domains creation
cpuidle: dt_idle_genpd: Add helper function to remove genpd topology
|
|
Pull drm fixes from Dave Airlie:
"This week's fixes, as expected amdgpu is probably a little larger
since it skipped a week, but otherwise a few nouveau fixes, a couple
of bridge, rockchip and ivpu fixes.
amdgpu:
- S/G display workaround for platforms with >= 64G of memory
- S0i3 fix
- SMU 13.0.0 fixes
- Disable SMU 13.x OD features temporarily while the interface is
reworked to enable additional functionality
- Fix cursor gamma issues on DCN3+
- SMU 13.0.6 fixes
- Fix possible UAF in CS IOCTL
- Polaris display regression fix
- Only enable CP GFX shadowing on SR-IOV
amdkfd:
- Raven/Picasso KFD regression fix
bridge:
- it6505: runtime PM fix
- lt9611: revert Do not generate HFP/HBP/HSA and EOT packet
nouveau:
- enable global memory loads for helper invocations for userspace
driver
- dp 1.3 dpcd+ workaround fix
- remove unused function
- revert incorrect NULL check
accel/ivpu:
- Add set_pages_array_wc/uc for internal buffers
rockchip:
- Don't spam logs in atomic check"
* tag 'drm-fixes-2023-08-11' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/shmem-helper: Reset vma->vm_ops before calling dma_buf_mmap()
drm/amdkfd: disable IOMMUv2 support for Raven
drm/amdkfd: disable IOMMUv2 support for KV/CZ
drm/amdkfd: ignore crat by default
drm/amdgpu/gfx11: only enable CP GFX shadowing on SR-IOV
drm/amd/display: Fix a regression on Polaris cards
drm/amdgpu: fix possible UAF in amdgpu_cs_pass1()
drm/amd/pm: Fix SMU v13.0.6 energy reporting
drm/amd/display: check attr flag before set cursor degamma on DCN3+
drm/amd/pm: disable the SMU13 OD feature support temporarily
drm/amd/pm: correct the pcie width for smu 13.0.0
drm/amd/display: Don't show stack trace for missing eDP
drm/amdgpu: Match against exact bootloader status
drm/amd/pm: skip the RLC stop when S0i3 suspend for SMU v13.0.4/11
drm/amd: Disable S/G for APUs when 64GB or more host memory
drm/rockchip: Don't spam logs in atomic check
accel/ivpu: Add set_pages_array_wc/uc for internal buffers
drm/nouveau/disp: Revert a NULL check inside nouveau_connector_get_modes
Revert "drm/bridge: lt9611: Do not generate HFP/HBP/HSA and EOT packet"
drm/nouveau: remove unused tu102_gr_load() function
...
|
|
Add 4 new Dell Dolphin Systems, same configuration as older systems.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230811123044.1045651-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now nvme_ns_chr_uring_cmd_iopoll() has switched to request based io
polling, and the associated NS is guaranteed to be live in case of
io polling, so request is guaranteed to be valid because blk-mq uses
pre-allocated request pool.
Remove the rcu read lock in nvme_ns_chr_uring_cmd_iopoll(), which
isn't needed any more after switching to request based io polling.
Fix "BUG: sleeping function called from invalid context" because
set_page_dirty_lock() from blk_rq_unmap_user() may sleep.
Fixes: 585079b6e425 ("nvme: wire up async polling for io passthrough commands")
Reported-by: Guangwu Zhang <guazhang@redhat.com>
Cc: Kanchan Joshi <joshi.k@samsung.com>
Cc: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Guangwu Zhang <guazhang@redhat.com>
Link: https://lore.kernel.org/r/20230809020440.174682-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Enabling tmpfs "direct IO" exposes it to invalidate_inode_pages2_range(),
which when swapping can hit the VM_BUG_ON_FOLIO(!folio_contains()): the
folio has been moved from page cache to swap cache (with folio->mapping
reset to NULL), but the folio_index() embedded in folio_contains() sees
swapcache, and so returns the swapcache_index() - whereas folio->index
would be the right one to check against the index from mapping's xarray.
There are different ways to fix this, but my preference is just to order
the checks in invalidate_inode_pages2_range() the same way that they are
in __filemap_get_folio() and find_lock_entries() and filemap_fault():
check folio->mapping before folio_contains().
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <f0b31772-78d7-f198-6482-9f25aab8c13f@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Depending upon your philosophical viewpoint, either tmpfs always does
direct IO, or it cannot ever do direct IO; but whichever, if tmpfs is to
stand in for a more sophisticated filesystem, it can be helpful for tmpfs
to support O_DIRECT. So, give tmpfs a shmem_file_open() method, to set
the FMODE_CAN_ODIRECT flag: then unchanged shmem_file_read_iter() and new
shmem_file_write_iter() do the work (without any shmem_direct_IO() stub).
Perhaps later, once the direct_IO method has been eliminated from all
filesystems, generic_file_write_iter() will be such that tmpfs can again
use it, even for O_DIRECT.
xfstests auto generic which were not run on tmpfs before but now pass:
036 091 113 125 130 133 135 198 207 208 209 210 211 212 214 226 239 263
323 355 391 406 412 422 427 446 451 465 551 586 591 609 615 647 708 729
with no new failures.
LTP dio tests which were not run on tmpfs before but now pass:
dio01 through dio30, except for dio04 and dio10, which fail because
tmpfs dio read and write allow odd count: tmpfs could be made stricter,
but would that be an improvement?
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <6f2742-6f1f-cae9-7c5b-ed20fc53215@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Our ABI opts to provide future proofing by defining a much larger
SVE_VQ_MAX than the architecture actually supports. Since we use
this define to control the size of our vector data buffers this results
in a lot of overhead when we initialise which can be a very noticable
problem in emulation, we fill buffers that are orders of magnitude
larger than we will ever actually use even with virtual platforms that
provide the full range of architecturally supported vector lengths.
Define and use the actual architecture maximum to mitigate this.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810-arm64-syscall-abi-perf-v1-1-6a0d7656359c@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add the LSE and various features check in the set of hwcap tests.
As stated in the ARM manual, the LSE2 feature allows for atomic access
to unaligned memory. Therefore, for processors that only have the LSE
feature, we register .sigbus_fn to test their ability to perform
unaligned access.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808134036.668954-6-zengheng4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Some enhanced features, such as the LSE2 feature, do not result in
SILLILL if LSE2 is missing and LSE is present, but will generate a
SIGBUS exception when atomic access unaligned.
Therefore, we add test item to test this type of features.
Notice that testing for SIGBUS only makes sense after make sure that
the instruction does not cause a SIGILL signal.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808134036.668954-5-zengheng4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add macro definition functions DEF_SIGHANDLER_FUNC() and
DEF_INST_RAISE_SIG() helpers.
Furthermore, there is no need to modify the default SIGILL handling
function throughout the entire testing lifecycle in the main() function.
It is reasonable to narrow the scope to the context of the sig_fn
function only.
This is a pre-patch for the subsequent SIGBUS handler patch.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808134036.668954-4-zengheng4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add the CRC32 feature check in the set of hwcap tests.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808134036.668954-3-zengheng4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add the FP feature check in the set of hwcap tests.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808134036.668954-2-zengheng4@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For a number of historical reasons, when handling SVCs we don't unmask
DAIF in el0_svc() or el0_svc_compat(), and instead do so later in
el0_svc_common(). This is unfortunate and makes it harder to make
changes to the DAIF management in entry-common.c as we'd like to do as
cleanup and preparation for FEAT_NMI support. We can move the DAIF
unmasking to entry-common.c as long as we also hoist the
fp_user_discard() logic, as reasoned below.
We converted the syscall trace logic from assembly to C in commit:
f37099b6992a0b81 ("arm64: convert syscall trace logic to C")
... which was intended to have no functional change, and mirrored the
existing assembly logic to avoid the risk of any functional regression.
With the logic in C, it's clear that there is currently no reason to
unmask DAIF so late within el0_svc_common():
* The thread flags are read prior to unmasking DAIF, but are not
consumed until after DAIF is unmasked, and we don't perform a
read-modify-write sequence of the thread flags for which we might need
to serialize against an IPI modifying the flags. Similarly, for any
thread flags set by other threads, whether DAIF is masked or not has
no impact.
The read_thread_flags() helpers performs a single-copy-atomic read of
the flags, and so this can safely be moved after unmasking DAIF.
* The pt_regs::orig_x0 and pt_regs::syscallno fields are neither
consumed nor modified by the handler for any DAIF exception (e.g.
these do not exist in the `perf_event_arm_regs` enum and are not
sampled by perf in its IRQ handler).
Thus, the manipulation of pt_regs::orig_x0 and pt_regs::syscallno can
safely be moved after unmasking DAIF.
Given the above, we can safely hoist unmasking of DAIF out of
el0_svc_common(), and into its immediate callers: do_el0_svc() and
do_el0_svc_compat(). Further:
* In do_el0_svc(), we sample the syscall number from
pt_regs::regs[8]. This is not modified by the handler for any DAIF
exception, and thus can safely be moved after unmasking DAIF.
As fp_user_discard() operates on the live FP/SVE/SME register state,
this needs to occur before we clear DAIF.IF, as interrupts could
result in preemption which would cause this state to become foreign.
As fp_user_discard() is the first function called within do_el0_svc(),
it has no dependency on other parts of do_el0_svc() and can be moved
earlier so long as it is called prior to unmasking DAIF.IF.
* In do_el0_svc_compat(), we sample the syscall number from
pt_regs::regs[7]. This is not modified by the handler for any DAIF
exception, and thus can safely be moved after unmasking DAIF.
Compat threads cannot use SVE or SME, so there's no need for
el0_svc_compat() to call fp_user_discard().
Given the above, we can safely hoist the unmasking of DAIF out of
do_el0_svc() and do_el0_svc_compat(), and into their immediate callers:
el0_svc() and el0_svc_compat(), so long a we also hoist
fp_user_discard() into el0_svc().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230808101148.1064172-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Use the generic fs_holder_ops to shut down the file system when the
log or RT device goes away instead of duplicating the logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Message-Id: <20230802154131.2221419-13-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Just like get_tree_bdev needs to drop s_umount when opening the main
device, we need to do the same for the xfs log and RT devices to avoid a
potential lock order reversal with s_unmount for the mark_dead path.
It might be preferable to just drop s_umount over ->fill_super entirely,
but that will require a fairly massive audit first, so we'll do the easy
version here first.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Message-Id: <20230802154131.2221419-12-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Use the generic fs_holder_ops to shut down the file system when the
log device goes away instead of duplicating the logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230802154131.2221419-11-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Just like get_tree_bdev needs to drop s_umount when opening the main
device, we need to do the same for the ext4 log device to avoid a
potential lock order reversal with s_unmount for the mark_dead path.
It might be preferable to just drop s_umount over ->fill_super entirely,
but that will require a fairly massive audit first, so we'll do the easy
version here first.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Message-Id: <20230802154131.2221419-10-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Export fs_holder_ops so that file systems that open additional block
devices can use it as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Message-Id: <20230802154131.2221419-9-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
fs_mark_dead currently uses get_super to find the superblock for the
block device that is going away. This means it is limited to the
main device stored in sb->s_dev, leading to a lot of code duplication
for file systems that can use multiple block devices.
Now that the holder for all block devices used by file systems is set
to the super_block, we can instead look at that holder and then check
if the file system is born and active, so do that instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Message-Id: <20230802154131.2221419-8-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The file system type is not a very useful holder as it doesn't allow us
to go back to the actual file system instance. Pass the super_block instead
which is useful when passed back to the file system driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Message-Id: <20230802154131.2221419-7-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d91 ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 25266128fe16 ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe16 ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable multigrain timestamps, which should ensure that there is an
apparent change to the timestamp whenever it has been written after
being actively observed via getattr.
Beyond enabling the FS_MGTIME flag, this patch eliminates
update_time_for_write, which goes to great pains to avoid in-memory
stores. Just have it overwrite the timestamps unconditionally.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230807-mgctime-v7-13-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Enable multigrain timestamps, which should ensure that there is an
apparent change to the timestamp whenever it has been written after
being actively observed via getattr.
For ext4, we only need to enable the FS_MGTIME flag.
Acked-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230807-mgctime-v7-12-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Enable multigrain timestamps, which should ensure that there is an
apparent change to the timestamp whenever it has been written after
being actively observed via getattr.
Also, anytime the mtime changes, the ctime must also change, and those
are now the only two options for xfs_trans_ichgtime. Have that function
unconditionally bump the ctime, and ASSERT that XFS_ICHGTIME_CHG is
always set.
Acked-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230807-mgctime-v7-11-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Enable multigrain timestamps, which should ensure that there is an
apparent change to the timestamp whenever it has been written after
being actively observed via getattr.
tmpfs only requires the FS_MGTIME flag.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230807-mgctime-v7-10-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The VFS always uses coarse-grained timestamps when updating the ctime
and mtime after a change. This has the benefit of allowing filesystems
to optimize away a lot metadata updates, down to around 1 per jiffy,
even when a file is under heavy writes.
Unfortunately, this has always been an issue when we're exporting via
NFSv3, which relies on timestamps to validate caches. A lot of changes
can happen in a jiffy, so timestamps aren't sufficient to help the
client decide to invalidate the cache. Even with NFSv4, a lot of
exported filesystems don't properly support a change attribute and are
subject to the same problems with timestamp granularity. Other
applications have similar issues with timestamps (e.g backup
applications).
If we were to always use fine-grained timestamps, that would improve the
situation, but that becomes rather expensive, as the underlying
filesystem would have to log a lot more metadata updates.
What we need is a way to only use fine-grained timestamps when they are
being actively queried.
POSIX generally mandates that when the the mtime changes, the ctime must
also change. The kernel always stores normalized ctime values, so only
the first 30 bits of the tv_nsec field are ever used.
Use the 31st bit of the ctime tv_nsec field to indicate that something
has queried the inode for the mtime or ctime. When this flag is set,
on the next mtime or ctime update, the kernel will fetch a fine-grained
timestamp instead of the usual coarse-grained one.
Filesytems can opt into this behavior by setting the FS_MGTIME flag in
the fstype. Filesystems that don't set this flag will continue to use
coarse-grained timestamps.
Later patches will convert individual filesystems to use the new
infrastructure.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230807-mgctime-v7-9-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
