| Age | Commit message (Collapse) | Author |
|---|
|
Document the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
It's controlled by using system configuration registers (SYSCFG).
Introduce two compatibles as the booster regulator is controlled by:
- a unique register/bit in STM32H7
- a set/clear register pair in STM32MP1
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
This regulator is supplied by vdda. It's controlled by using SYSCFG:
- STM32H7 has a unique register to set/clear the booster enable bit
- STM32MP1 has separate set and clear registers to configure it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: 30846090a746 ("xfrm: policy: add sequence count to sync with hash resize")
Cc: Florian Westphal <fw@strlen.de>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this Alienware branded Primax mouse as well.
Daniel Schepler (@dschepler) reported and tested the quirk.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/15
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add the product ID for the 2nd Generation Intuos Pro
Small to the touchring coordinate adjustment block.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Rename the HID documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
While here, fix the sysfs example from hid-sensor.txt, that
has a lot of "?" instead of the proper UTF-8 characters that
are produced by the tree command.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
paranoid_exit needs to restore CR3 before GSBASE. Doing it in the opposite
order crashes if the exception came from a context with user GSBASE and
user CR3 -- RESTORE_CR3 cannot resture user CR3 if run with user GSBASE.
This results in infinitely recursing exceptions if user code does SYSENTER
with TF set if both FSGSBASE and PTI are enabled.
The old code worked if user code just set TF without SYSENTER because #DB
from user mode is special cased in idtentry and paranoid_exit doesn't run.
Fix it by cleaning up the spaghetti code. All that paranoid_exit needs to
do is to disable IRQs, handle IRQ tracing, then restore CR3, and restore
GSBASE. Simply do those actions in that order.
Fixes: 708078f65721 ("x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: https://lkml.kernel.org/r/59725ceb08977359489fbed979716949ad45f616.1562035429.git.luto@kernel.org
|
|
It's only used if !CONFIG_IA32_EMULATION, so disable it in normal
configs. This will save a few bytes of text and reduce confusion.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "BaeChang Seok" <chang.seok.bae@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Bae, Chang Seok" <chang.seok.bae@intel.com>
Link: https://lkml.kernel.org/r/0f7dafa72fe7194689de5ee8cfe5d83509fabcf5.1562035429.git.luto@kernel.org
|
|
Make sure that both variants of the nasty TF-in-compat-syscall are
exercised regardless of what vendor's CPU is running the tests.
Also change the intentional signal after SYSCALL to use ud2, which
is a lot more comprehensible.
This crashes the kernel due to an FSGSBASE bug right now.
This test *also* detects a bug in KVM when run on an Intel host. KVM
people, feel free to use it to help debug. There's a bunch of code in this
test to warn instead of going into an infinite looping when the bug gets
triggered.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "BaeChang Seok" <chang.seok.bae@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: "Bae, Chang Seok" <chang.seok.bae@intel.com>
Link: https://lkml.kernel.org/r/5f5de10441ab2e3005538b4c33be9b1965d1bb63.1562035429.git.luto@kernel.org
|
|
Fix sparse warnings:
lib/reed_solomon/test_rslib.c:313:5: warning: symbol 'ex_rs_helper' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:349:5: warning: symbol 'exercise_rs' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:407:5: warning: symbol 'exercise_rs_bc' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <ferdinand.blomqvist@gmail.com>
Link: https://lkml.kernel.org/r/20190702061847.26060-1-yuehaibing@huawei.com
|
|
Catherine Sullivan says:
====================
Add gve driver
This patch series adds the gve driver which will support the
Compute Engine Virtual NIC that will be available in the future.
v2:
- Patch 1:
- Remove gve_size_assert.h and use static_assert instead.
- Loop forever instead of bugging if the device won't reset
- Use module_pci_driver
- Patch 2:
- Use be16_to_cpu in the RX Seq No define
- Remove unneeded ndo_change_mtu
- Patch 3:
- No Changes
- Patch 4:
- Instead of checking netif_carrier_ok in ethtool stats, just make sure
v3:
- Patch 1:
- Remove X86 dep
- Patch 2:
- No changes
- Patch 3:
- No changes
- Patch 4:
- Remove unneeded memsets in ethtool stats
v4:
- Patch 1:
- Use io[read|write]32be instead of [read|write]l(cpu_to_be32())
- Explicitly add padding to gve_adminq_set_driver_parameter
- Use static where appropriate
- Patch 2:
- Use u64_stats_sync
- Explicity add padding to gve_adminq_create_rx_queue
- Fix some enianness typing issues found by kbuild
- Use static where appropriate
- Remove unused variables
- Patch 3:
- Use io[read|write]32be instead of [read|write]l(cpu_to_be32())
- Patch 4:
- Use u64_stats_sync
- Use static where appropriate
Warnings reported by:
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the following ethtool commands:
ethtool -s|--change devname [msglvl N] [msglevel type on|off]
ethtool -S|--statistics devname
ethtool -i|--driver devname
ethtool -l|--show-channels devname
ethtool -L|--set-channels devname
ethtool -g|--show-ring devname
ethtool --reset devname
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the workqueue to handle management interrupts and
support for resets.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for passing traffic.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a driver framework for the Compute Engine Virtual NIC that will be
available in the future.
At this point the only functionality is loading the driver.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mahesh Bandewar says:
====================
blackhole device to invalidate dst
When we invalidate dst or mark it "dead", we assign 'lo' to
dst->dev. First of all this assignment is racy and more over,
it has MTU implications.
The standard dev MTU is 1500 while the Loopback MTU is 64k. TCP
code when dereferencing the dst don't check if the dst is valid
or not. TCP when dereferencing a dead-dst while negotiating a
new connection, may use dst device which is 'lo' instead of
using the correct device. Consider the following scenario:
A SYN arrives on an interface and tcp-layer while processing
SYNACK finds a dst and associates it with SYNACK skb. Now before
skb gets passed to L3 for processing, if that dst gets "dead"
(because of the virtual device getting disappeared & then reappeared),
the 'lo' gets assigned to that dst (lo MTU = 64k). Let's assume
the SYN has ADV_MSS set as 9k while the output device through
which this SYNACK is going to go out has standard MTU of 1500.
The MTU check during the route check passes since MIN(9K, 64K)
is 9k and TCP successfully negotiates 9k MSS. The subsequent
data packet; bigger in size gets passed to the device and it
won't be marked as GSO since the assumed MTU of the device is
9k.
This either crashes the NIC and we have seen fixes that went
into drivers to handle this scenario. 8914a595110a ('bnx2x:
disable GSO where gso_size is too big for hardware') and
2b16f048729b ('net: create skb_gso_validate_mac_len()') and
with those fixes TCP eventually recovers but not before
few dropped segments.
Well, I'm not a TCP expert and though we have experienced
these corner cases in our environment, I could not reproduce
this case reliably in my test setup to try this fix myself.
However, Michael Chan <michael.chan@broadcom.com> had a setup
where these fixes helped him mitigate the issue and not cause
the crash.
The idea here is to not alter the data-path with additional
locks or smb()/rmb() barriers to avoid racy assignments but
to create a new device that has really low MTU that has
.ndo_start_xmit essentially a kfree_skb(). Make use of this
device instead of 'lo' when marking the dst dead.
First patch implements the blackhole device and second
patch uses it in IPv4 and IPv6 stack while the third patch
is the self test that ensures the sanity of this device.
v1->v2
fixed the self-test patch to handle the conflict
v2 -> v3
fixed Kconfig text/string.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since this is not really a device with all capabilities, this test
ensures that it has *enough* to make it through the data path
without causing unwanted side-effects (read crash!).
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use blackhole_netdev instead of 'lo' device with lower MTU when marking
dst "dead".
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Tested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a blackhole net device that can be used for "dead"
dst entries instead of loopback device. This blackhole device differs
from loopback in few aspects: (a) It's not per-ns. (b) MTU on this
device is ETH_MIN_MTU (c) The xmit function is essentially kfree_skb().
and (d) since it's not registered it won't have ifindex.
Lower MTU effectively make the device not pass the MTU check during
the route check when a dst associated with the skb is dead.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Rename r8153b_queue_wake() to r8153_queue_wake().
2. Correct the setting. The enable bit should be 0xd38c bit 0. Besides,
the 0xd38a bit 0 and 0xd398 bit 8 have to be cleared for both enabled
and disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unneeded memset as alloc_etherdev is using kvzalloc which uses
__GFP_ZERO flag
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ilias Apalodimas says:
====================
net: netsec: Add XDP Support
This is a respin of https://www.spinics.net/lists/netdev/msg526066.html
Since page_pool API fixes are merged into net-next we can now safely use
it's DMA mapping capabilities.
First patch changes the buffer allocation from napi/netdev_alloc_frag()
to page_pool API. Although this will lead to slightly reduced performance
(on raw packet drops only) we can use the API for XDP buffer recycling.
Another side effect is a slight increase in memory usage, due to using a
single page per packet.
The second patch adds XDP support on the driver.
There's a bunch of interesting options that come up due to the single
Tx queue.
Locking is needed(to avoid messing up the Tx queues since ndo_xdp_xmit
and the normal stack can co-exist). We also need to track down the
'buffer type' for TX and properly free or recycle the packet depending
on it's nature.
Changes since RFC:
- Bug fixes from Jesper and Maciej
- Added page pool API to retrieve the DMA direction
Changes since v1:
- Use page_pool_free correctly if xdp_rxq_info_reg() failed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interface only supports 1 Tx queue so locking is introduced on
the Tx queue if XDP is enabled to make sure .ndo_start_xmit and
.ndo_xdp_xmit won't corrupt Tx ring
- Performance (SMMU off)
Benchmark XDP_SKB XDP_DRV
xdp1 291kpps 344kpps
rxdrop 282kpps 342kpps
- Performance (SMMU on)
Benchmark XDP_SKB XDP_DRV
xdp1 167kpps 324kpps
rxdrop 164kpps 323kpps
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the dma direction is stored in page pool params, offer an API
helper for driver that choose not to keep track of it locally
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use page_pool and it's DMA mapping capabilities for Rx buffers instead
of netdev/napi_alloc_frag()
Although this will result in a slight performance penalty on small sized
packets (~10%) the use of the API will allow to easily add XDP support.
The penalty won't be visible in network testing i.e ipef/netperf etc, it
only happens during raw packet drops.
Furthermore we intend to add recycling capabilities on the API
in the future. Once the recycling is added the performance penalty will
go away.
The only 'real' penalty is the slightly increased memory usage, since we
now allocate a page per packet instead of the amount of bytes we need +
skb metadata (difference is roughly 2kb per packet).
With a minimum of 4BG of RAM on the only SoC that has this NIC the
extra memory usage is negligible (a bit more on 64K pages)
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 86029d10af18 ("tls: zero the crypto information from tls_context
before freeing") added memzero_explicit() calls to clear the key material
before freeing struct tls_context, but it missed tls_device.c has its
own way of freeing this structure. Replace the missing free.
Fixes: 86029d10af18 ("tls: zero the crypto information from tls_context before freeing")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neither drivers nor the tls offload code currently supports TLS
version 1.3. Check the TLS version when installing connection
state. TLS 1.3 will just fallback to the kernel crypto for now.
Fixes: 130b392c6cd6 ("net: tls: Add tls 1.3 support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roman Mashak says:
====================
Fix batched event generation for mirred action
When adding or deleting a batch of entries, the kernel sends upto
TCA_ACT_MAX_PRIO entries in an event to user space. However it does not
consider that the action sizes may vary and require different skb sizes.
For example :
% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"
$TC actions flush action mirred
for i in `seq 1 $1`;
do
cmd="action mirred egress redirect dev lo index $i "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
patch 1 adds callback in tc_action_ops of mirred action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().
patch 2 updates the TDC test suite with relevant test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cong Wang says:
====================
idr: fix overflow cases on 32-bit CPU
idr_get_next_ul() is problematic by design, it can't handle
the following overflow case well on 32-bit CPU:
u32 id = UINT_MAX;
idr_alloc_u32(&id);
while (idr_get_next_ul(&id) != NULL)
id++;
when 'id' overflows and becomes 0 after UINT_MAX, the loop
goes infinite.
Fix this by eliminating external users of idr_get_next_ul()
and migrating them to idr_for_each_entry_continue_ul(). And
add an additional parameter for these iteration macros to detect
overflow properly.
Please merge this through networking tree, as all the users
are in networking subsystem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly, other callers of idr_get_next_ul() suffer the same
overflow bug as they don't handle it properly either.
Introduce idr_for_each_entry_continue_ul() to help these callers
iterate from a given ID.
cls_flower needs more care here because it still has overflow when
does arg->cookie++, we have to fold its nested loops into one
and remove the arg->cookie++.
Fixes: 01683a146999 ("net: sched: refactor flower walk to iterate over idr")
Fixes: 12d6066c3b29 ("net/mlx5: Add flow counters idr")
Reported-by: Li Shuang <shuali@redhat.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Chris Mi <chrism@mellanox.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
idr_for_each_entry_ul() is buggy as it can't handle overflow
case correctly. When we have an ID == UINT_MAX, it becomes an
infinite loop. This happens when running on 32-bit CPU where
unsigned long has the same size with unsigned int.
There is no better way to fix this than casting it to a larger
integer, but we can't just 64 bit integer on 32 bit CPU. Instead
we could just use an additional integer to help us to detect this
overflow case, that is, adding a new parameter to this macro.
Fortunately tc action is its only user right now.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Reported-by: Li Shuang <shuali@redhat.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Chris Mi <chrism@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
People are inclined to stuff random things into cb->args[n] because it
looks like an array of integers. Sometimes people even put u64s in there
with comments noting that a certain member takes up two slots. The
horror! Really this should mirror the usage of skb->cb, which are just
48 opaque bytes suitable for casting a struct. Then people can create
their usual casting macros for accessing strongly typed members of a
struct.
As a plus, this also gives us the same amount of space on 32bit and 64bit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro TIPC_BC_RETR_LIM is always used in combination with 'jiffies',
so we can just as well perform the addition in the macro itself. This
way, we get a few shorter code lines and one less line break.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stefano Garzarella says:
====================
vsock/virtio: several fixes in the .probe() and .remove()
During the review of "[PATCH] vsock/virtio: Initialize core virtio vsock
before registering the driver", Stefan pointed out some possible issues
in the .probe() and .remove() callbacks of the virtio-vsock driver.
This series tries to solve these issues:
- Patch 1 adds RCU critical sections to avoid use-after-free of
'the_virtio_vsock' pointer.
- Patch 2 stops workers before to call vdev->config->reset(vdev) to
be sure that no one is accessing the device.
- Patch 3 moves the works flush at the end of the .remove() to avoid
use-after-free of 'vsock' object.
v2:
- Patch 1: use RCU to protect 'the_virtio_vsock' pointer
- Patch 2: no changes
- Patch 3: flush works only at the end of .remove()
- Removed patch 4 because virtqueue_detach_unused_buf() returns all the buffers
allocated.
v1: https://patchwork.kernel.org/cover/10964733/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the flush of works after vdev->config->del_vqs(vdev),
because we need to be sure that no workers run before to free the
'vsock' object.
Since we stopped the workers using the [tx|rx|event]_run flags,
we are sure no one is accessing the device while we are calling
vdev->config->reset(vdev), so we can safely move the workers' flush.
Before the vdev->config->del_vqs(vdev), workers can be scheduled
by VQ callbacks, so we must flush them after del_vqs(), to avoid
use-after-free of 'vsock' object.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before to call vdev->config->reset(vdev) we need to be sure that
no one is accessing the device, for this reason, we add new variables
in the struct virtio_vsock to stop the workers during the .remove().
This patch also add few comments before vdev->config->reset(vdev)
and vdev->config->del_vqs(vdev).
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some callbacks used by the upper layers can run while we are in the
.remove(). A potential use-after-free can happen, because we free
the_virtio_vsock without knowing if the callbacks are over or not.
To solve this issue we move the assignment of the_virtio_vsock at the
end of .probe(), when we finished all the initialization, and at the
beginning of .remove(), before to release resources.
For the same reason, we do the same also for the vdev->priv.
We use RCU to be sure that all callbacks that use the_virtio_vsock
ended before freeing it. This is not required for callbacks that
use vdev->priv, because after the vdev->config->del_vqs() we are sure
that they are ended and will no longer be invoked.
We also take the mutex during the .remove() to avoid that .probe() can
run while we are resetting the device.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__vxlan_dev_create() destroys FDB using specific pointer which indicates
a fdb when error occurs.
But that pointer should not be used when register_netdevice() fails because
register_netdevice() internally destroys fdb when error occurs.
This patch makes vxlan_fdb_create() to do not link fdb entry to vxlan dev
internally.
Instead, a new function vxlan_fdb_insert() is added to link fdb to vxlan
dev.
vxlan_fdb_insert() is called after calling register_netdevice().
This routine can avoid situation that ->ndo_uninit() destroys fdb entry
in error path of register_netdevice().
Hence, error path of __vxlan_dev_create() routine can have an opportunity
to destroy default fdb entry by hand.
Test command
ip link add bonding_masters type vxlan id 0 group 239.1.1.1 \
dev enp0s9 dstport 4789
Splat looks like:
[ 213.392816] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 213.401257] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 213.402178] CPU: 0 PID: 1414 Comm: ip Not tainted 5.2.0-rc5+ #256
[ 213.402178] RIP: 0010:vxlan_fdb_destroy+0x120/0x220 [vxlan]
[ 213.402178] Code: df 48 8b 2b 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 06 01 00 00 4c 8b 63 08 48 b8 00 00 00 00 00 fc d
[ 213.402178] RSP: 0018:ffff88810cb9f0a0 EFLAGS: 00010202
[ 213.402178] RAX: dffffc0000000000 RBX: ffff888101d4a8c8 RCX: 0000000000000000
[ 213.402178] RDX: 1bd5a00000000040 RSI: ffff888101d4a8c8 RDI: ffff888101d4a8d0
[ 213.402178] RBP: 0000000000000000 R08: fffffbfff22b72d9 R09: 0000000000000000
[ 213.402178] R10: 00000000ffffffef R11: 0000000000000000 R12: dead000000000200
[ 213.402178] R13: ffff88810cb9f1f8 R14: ffff88810efccda0 R15: ffff88810efccda0
[ 213.402178] FS: 00007f7f6621a0c0(0000) GS:ffff88811b000000(0000) knlGS:0000000000000000
[ 213.402178] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 213.402178] CR2: 000055746f0807d0 CR3: 00000001123e0000 CR4: 00000000001006f0
[ 213.402178] Call Trace:
[ 213.402178] __vxlan_dev_create+0x3a9/0x7d0 [vxlan]
[ 213.402178] ? vxlan_changelink+0x740/0x740 [vxlan]
[ 213.402178] ? rcu_read_unlock+0x60/0x60 [vxlan]
[ 213.402178] ? __kasan_kmalloc.constprop.3+0xa0/0xd0
[ 213.402178] vxlan_newlink+0x8d/0xc0 [vxlan]
[ 213.402178] ? __vxlan_dev_create+0x7d0/0x7d0 [vxlan]
[ 213.554119] ? __netlink_ns_capable+0xc3/0xf0
[ 213.554119] __rtnl_newlink+0xb75/0x1180
[ 213.554119] ? rtnl_link_unregister+0x230/0x230
[ ... ]
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
/proc/sys/net/ipv6/flowlabel_reflect assumes written value to be in the
range of 0 to 3. Use proc_dointvec_minmax instead of proc_dointvec.
Fixes: 323a53c41292 ("ipv6: tcp: enable flowlabel reflection in some RST packets")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When user has configured a large number of virtual netdev, such
as 4K vlans, the carrier on/off operation of the real netdev
will also cause it's virtual netdev's link state to be processed
in linkwatch. Currently, the processing is done in a work queue,
which may cause rtnl locking starvation problem and worker
starvation problem for other work queue, such as irqfd_inject wq.
This patch releases the cpu when link watch worker has processed
a fixed number of netdev' link watch event, and schedule the
work queue again when there is still link watch event remaining.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It allocates the extended area for outbound streams only on sendmsg
calls, if they are not yet allocated. When using the priority
stream scheduler, this initialization may imply into a subsequent
allocation, which may fail. In this case, it was aborting the stream
scheduler initialization but leaving the ->ext pointer (allocated) in
there, thus in a partially initialized state. On a subsequent call to
sendmsg, it would notice the ->ext pointer in there, and trip on
uninitialized stuff when trying to schedule the data chunk.
The fix is undo the ->ext initialization if the stream scheduler
initialization fails and avoid the partially initialized state.
Although syzkaller bisected this to commit 4ff40b86262b ("sctp: set
chunk transport correctly when it's a new asoc"), this bug was actually
introduced on the commit I marked below.
Reported-by: syzbot+c1a380d42b190ad1e559@syzkaller.appspotmail.com
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations")
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the skb is associated with a new sock, just assigning
it to skb->sk is not sufficient, we have to set its destructor
to free the sock properly too.
Reported-by: syzbot+d6636a36d3c34bd88938@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
