| Age | Commit message (Collapse) | Author |
|---|
|
At the moment we have the following interrupt enabling sequence:
1. irq preinstall hook
2. enabling the interrupt handler and calling irq postinstall hook
3. enable rps interrupts from the async work
And the folliwing disable sequence:
1. disabling the interrupt handler and calling the uninstall hook
2. disabling the rps interrupt
Since the postinstall hook now always sets up PMIIR, PMIER and PMIMR
to known-good states there no way for an interrupt to sneak in in the
enable sequence, so we can reinstate the WARN lost in
commit eda63ffb906c2fb3b609a0e87aeb63c0f25b9e6b
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
Note that there's some room for future cleanups since most of the
interrupt register clearing in the disable function is rather
redundant. But that's better done in follow-up patches, if at all.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The VECS enabling required some changes to how rps interrupts are
enabled/disabled since VECS interrupts are handling with the PM
interrupt registers.
But now that the pre/postinstall sequences is identical for all
platforms with rps support (snb, ivb, hsw, vlv) we can also use the
exact same sequence to actually enable the rps interrupts. Strictly
speaking using spinlocks is overkill on snb/ivb & vlv since they have
no VECS ring, but imo that's more than made up by the common code.
Hence this just unifies the vlv code with the snb-hsw code which
matched exactly before the VECS enabling. See
commit eda63ffb906c2fb3b609a0e87aeb63c0f25b9e6b
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:26 2013 -0700
drm/i915: Add PM regs to pre/post install
and
commit 4848405cced3b46f4ec7d404b8ed5873171ae10a
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:27 2013 -0700
drm/i915: make PM interrupt writes non-destructive
for why the gen6 code (shared between snb, ivb and hsw) needed to be
changed originally.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Again extract a common helper. For the postinstall hook things are a
bit more complicated since we have more cases on ilk-hsw/vlv here.
But since vlv was clearly broken by failing to initialize
dev_priv->gt_irq_mask correctly the shared code is clearly justified.
Also kill the PMIER setting in the async rps enable work. I should
have been save, but also clearly looked rather fragile. PMIER setup is
now all down in the irq pre/postinstall hooks.
With this we now have the usual interrupt register sequence for GT/PM
irq registers:
- IER is setup once with all the interrupts we ever need in the
postinstall hook and never touched again. Exceptions are SDEIER,
which is touched in the preinstall hook (when the irq handler isn't
enabled) and then only from the irq handler. And DEIER/VLV_IER with
is used in the irq handler but also written to once in the
postinstall hook. But since that write is essentially what enables
the interrupt and we should always have MSI interrupts we should be
save. In case we ever have non-MSI interrupts we'd be screwed.
- IIR is cleared in the postinstall hook before we enable/unmask the
respective interrupt sources. Hence we can't steal an interrupt
event an accidentally trigger the spurious interrupt logic in the
core kernel. Note that after some discussion with Ben Widawsky we
think that we actually should clear the IIR registers in the
preinstall hook. But doing that is a much larger patch series.
- IMR regs are (usually) all masked off. Those are the only regs
changed at runtime, which is all protected by dev_priv->irq_lock.
This unification also kills the cargo-culted read-modify-write PM
register setup for VECS. Interrupt setup is done without userspace
being able to interfere, so we better know what values we want to put
into those registers. RMW cycles otoh are really good at papering over
races, until stuff magically blows up and no one has a clue why.
v2: Touch the gen6+ PM interrupt registers only on gen6+.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a comment to explain why the l3 parity interrupt is
special.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip.
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since the addition of VECS we have a slightly different enable
sequence for PM interrupts on ivb/hsw vs snb and vlv. Usually that
will end up in hard to track down surprises.
Hence unifiy things and since we have copies of this code in 3 places
now, extract it into its own little helper.
Note that this changes the irq preinstall sequence a bit for snb and
vlv: We now also clear the PM registers in the preinstall hook, in
addition to the PM register clearing/setup already done when actually
enabling rps. So this doesn't fix a bug but simply unifies the code
across all platforms. After the postinstall hook is similarly unified
we can rip out the then redundant PM interrupt setup from the rps
code.
v3: Rebase on top of the retained double-GTIIR clearing. Also
resurrect the masking/disabling of the gen6+ PM interrupts as spotted
by Ben Widaswky.
v4: Move the DE interrupt reset code out of gen5_gt_irq_preinstall
back to ironlake_irq_preinstall where it really belongs. Spotted by
Paulo.
v3: Improve the commit message to more clearly spell out why we want
to unify the code and what exactly changes.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: s/GT/PM/ to fix up a comment which Ben spotted while
reviewing.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
To make users life a little easier figuring out what they have on their
system.
Ideally, I'd really like to report LLC size, but it turned out to be a
bit of a pain. Maybe I'll revisit it in the future.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
DRI clients really should be using MOCS to get fine grained streaming
cache controls. With that note, I *hope* that this patch doesn't improve
performance overwhelmingly, because if it does - it means there is a
problem elsewhere.
In any case, the kernel, and old userspace should get some benefit from
this, so let's do it. eLLC is always a good default, and really not
using it is the special case for MOCS.
References: http://www.intel.com/newsroom/kits/restricted/ha$well!/pdfs/4th_Gen_Intel_Core_PressBriefing_5-29.pdf (page 57)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The eLLC cannot be determined by PCIID because as far as we know, even
machines supporting eLLC may not have it enabled, or fused off or
whatever. It's possible this isn't actually true, and at that point we
can switch to a DEV_INFO flag instead.
I've defined everything where the docs are clear, and left the rest as
magic.
But we need it before we set the pte_encode function pointers, which
happens really early, in gtt_init.
The problem with just doing the normal sequence earlier is we don't have
the ability to use forcewake until after the pte functions have been set
up.
Since all solutions are somewhat ugly (barring rewriting all the init
ordering), I've opted to do the detection really early, and the enabling
later - since the register to detect doesn't require forcewake.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Move dev_priv->ellc_size away from the dri1 dungeon to a nice
place right next to the l3 parity stuff. Also squash in the follow-up
commit to read out the eLLC size a bit earlier.]
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The EDRAM present register isn't really defined in the docs. It just
says check to see if it's set to 1. So I haven't defined the 1 value not
knowing what it actually means.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The cacheability controls have changed, and the bits have been
rearranged in general.
Note that age 0 is the oldest (most likely to get evicted) and age 3
is the youngest (most likely to stick around for a bit). We've picked
0 for no reason, but atm it shouldn't matter anyway (since we don't
yet try to differentiate between different objects).
v2: Remove comments for snb/ivb cache leves, that's a separate change.
v3: Resolve conflicts due to patch series reordering.
v4: Rebased on top of Kenneth Graunke's ->pte_encode refactoring.
v5: Removed eLLC bits for separate patch.
In the internal repository this was:
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add comment about cache ages as requested by Ben provoked due
to a question from Damien.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Although it is unlikley that physical package id is set to some
arbitary number, it is better to prevent in anycase. Since package
temp zones use this in thermal zone type and for allocation, added
a limit.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Fixup for commit "uvesafb: Clean up MTRR code"
(63e28a7a5ffce59b645ca9cbcc01e1e8be56bd75)
Signed-off-by: Sylvain "ythier" Hitier <sylvain.hitier@gmail.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Also-spotted-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
More DPM fixes, r6xx DMA fix for bo moving, UVD fixes,
one major regression fix on bootup on some machine (ttm backoff missing)
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
radeon kms: do not flush uninitialized hotplug work
drm/radeon/dpm/sumo: handle boost states properly when forcing a perf level
drm/radeon: align VM PTBs (Page Table Blocks) to 32K
drm/radeon: allow selection of alignment in the sub-allocator
drm/radeon: never unpin UVD bo v3
drm/radeon: fix UVD fence emit
drm/radeon: add fault decode function for CIK
drm/radeon: add fault decode function for SI (v2)
drm/radeon: add fault decode function for cayman/TN (v2)
drm/radeon: use radeon device for request firmware
drm/radeon: add missing ttm_eu_backoff_reservation to radeon_bo_list_validate
drm/radeon: use CP DMA on r6xx for bo moves
drm/radeon: implement bo copy callback using CP DMA (v2)
drm/radeon: Disable dma rings for bo moves on r6xx
drm/radeon/dpm: disable gfx PG on PALM
drm/radeon/hdmi: make sure we have an afmt block assigned
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix regmap crash for async operation on busless maps
This fixes a crash if something tries to do an asynchronous operation
on busless maps which was introduced during the merge window"
* tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: cache: bail in regmap_async_complete() for bus-less maps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of things missed during the v3.11 work here:
- The spi-bitbang core requires a setup() function even if it does
nothing which caused breakage when some empty setup functions were
removed after their contents were factored out into the core.
While this is clearly silly and will be fixed for v3.12 for now we
just restore the functions.
- A missing case handled in the s3c64xx driver"
* tag 'spi-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: revert master->setup function removal for altera and nuc900
spi/xilinx: Revert master->setup function removal
spi: s3c64xx: add missing check for polling mode
|
|
There are CPUs which have errata causing RDMSR of a nonexistent MSR to
not fault. We would then try to WRMSR to restore the value of that
MSR, causing a crash. Specifically, some Pentium M variants would
have this problem trying to save and restore the non-existent EFER,
causing a crash on resume.
Work around this by making sure we can write back the result at
suspend time.
Huge thanks to Christian Sünkenberg for finding the offending erratum
that finally deciphered the mystery.
Reported-and-tested-by: Johan Heinrich <onny@project-insanity.org>
Debugged-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/51DDC972.3010005@student.kit.edu
Cc: <stable@vger.kernel.org> # v3.7+
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We should use CONFIG_STACK_TRACER to guard readme text
of stack tracer related file, not CONFIG_STACKTRACE.
Link: http://lkml.kernel.org/r/51E3B3A2.8080609@huawei.com
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
During large unlink operations on files with extents, we can use a lot
of CPU time. This adds a cond_resched() call when starting to examine
the next level of a multi-level extent tree. Multi-level extent trees
are rare in the first place, and this should rarely be executed.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
My static checker marks everything from ntohl() as untrusted and it
complains we could have an underflow problem doing:
return (u32 *)&ary->wc_array[nchunks];
Also on 32 bit systems the upper bound check could overflow.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Fix the error pathway if rpcauth_create() fails.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Fix a warning from lockdep caused by calling flush_work() for
uninitialized hotplug work. Initialize hotplug_work, audio_work
and reset_work upon successful radeon_irq_kms_init() completion
and thus perform hotplug flush_work only when rdev->irq.installed
is true.
[ 4.790019] [drm] Loading CEDAR Microcode
[ 4.790943] r600_cp: Failed to load firmware "radeon/CEDAR_smc.bin"
[ 4.791152] [drm:evergreen_startup] *ERROR* Failed to load firmware!
[ 4.791330] radeon 0000:01:00.0: disabling GPU acceleration
[ 4.792633] INFO: trying to register non-static key.
[ 4.792792] the code is fine but needs lockdep annotation.
[ 4.792953] turning off the locking correctness validator.
[ 4.793114] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.11.0-rc0-dbg-10676-gfe56456-dirty #1816
[ 4.793314] Hardware name: Acer Aspire 5741G /Aspire 5741G , BIOS V1.20 02/08/2011
[ 4.793507] ffffffff821fd810 ffff8801530b9a18 ffffffff8160434e 0000000000000002
[ 4.794155] ffff8801530b9ad8 ffffffff810b8404 ffff8801530b0798 ffff8801530b0000
[ 4.794789] ffff8801530b9b00 0000000000000046 00000000000004c0 ffffffff00000000
[ 4.795418] Call Trace:
[ 4.795573] [<ffffffff8160434e>] dump_stack+0x4e/0x82
[ 4.795731] [<ffffffff810b8404>] __lock_acquire+0x1a64/0x1d30
[ 4.795893] [<ffffffff814a87f0>] ? dev_vprintk_emit+0x50/0x60
[ 4.796034] [<ffffffff810b8fb4>] lock_acquire+0xa4/0x200
[ 4.796216] [<ffffffff8106cd75>] ? flush_work+0x5/0x280
[ 4.796375] [<ffffffff8106cdad>] flush_work+0x3d/0x280
[ 4.796520] [<ffffffff8106cd75>] ? flush_work+0x5/0x280
[ 4.796682] [<ffffffff810b659d>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 4.796862] [<ffffffff8131d775>] ? delay_tsc+0x95/0xf0
[ 4.797024] [<ffffffff8141bb8b>] radeon_irq_kms_fini+0x2b/0x70
[ 4.797186] [<ffffffff814557c9>] evergreen_init+0x2a9/0x2e0
[ 4.797347] [<ffffffff813ebb1f>] radeon_device_init+0x5ef/0x700
[ 4.797511] [<ffffffff81335bc7>] ? pci_find_capability+0x47/0x50
[ 4.797672] [<ffffffff813edaed>] radeon_driver_load_kms+0x8d/0x150
[ 4.797843] [<ffffffff813ce426>] drm_get_pci_dev+0x166/0x280
[ 4.798007] [<ffffffff8116cff5>] ? kfree+0xf5/0x2e0
[ 4.798168] [<ffffffff813ea298>] ? radeon_pci_probe+0x98/0xd0
[ 4.798329] [<ffffffff813ea2aa>] radeon_pci_probe+0xaa/0xd0
[ 4.798489] [<ffffffff81339404>] pci_device_probe+0x84/0xe0
[ 4.798644] [<ffffffff814ac7d6>] driver_probe_device+0x76/0x240
[ 4.798805] [<ffffffff814aca73>] __driver_attach+0x93/0xa0
[ 4.798948] [<ffffffff814ac9e0>] ? __device_attach+0x40/0x40
[ 4.799126] [<ffffffff814aa82b>] bus_for_each_dev+0x6b/0xb0
[ 4.799272] [<ffffffff814ac2be>] driver_attach+0x1e/0x20
[ 4.799434] [<ffffffff814abec0>] bus_add_driver+0x1f0/0x280
[ 4.799596] [<ffffffff814ad0e4>] driver_register+0x74/0x150
[ 4.799758] [<ffffffff8133923d>] __pci_register_driver+0x5d/0x60
[ 4.799936] [<ffffffff81d16efc>] ? ttm_init+0x67/0x67
[ 4.800081] [<ffffffff813ce655>] drm_pci_init+0x115/0x130
[ 4.800243] [<ffffffff81d16efc>] ? ttm_init+0x67/0x67
[ 4.800405] [<ffffffff81d16f98>] radeon_init+0x9c/0xba
[ 4.800586] [<ffffffff810002ca>] do_one_initcall+0xfa/0x150
[ 4.800746] [<ffffffff81073f60>] ? parse_args+0x120/0x330
[ 4.800909] [<ffffffff81cdafae>] kernel_init_freeable+0x111/0x191
[ 4.801052] [<ffffffff81cda87a>] ? do_early_param+0x88/0x88
[ 4.801233] [<ffffffff815fb670>] ? rest_init+0x140/0x140
[ 4.801393] [<ffffffff815fb67e>] kernel_init+0xe/0x180
[ 4.801556] [<ffffffff8160dcac>] ret_from_fork+0x7c/0xb0
[ 4.801718] [<ffffffff815fb670>] ? rest_init+0x140/0x140
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Need to properly enable/disable boost states when forcing a performance
level.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Covers requirements of all current asics.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.11
The biggest change here is the OMAP change, these are larger than I'd
have liked but make the driver actually usable - during the merge window
OMAP removed support for non-DT OMAP4 boards but in doing so removed the
method of accessing DMA channels used by the ASoC drivers rendering them
unusuable.
Otherwise nothing exciting, the symmetric rates change for WM8978 is a
fix for the information we expose to userspace.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
While the conversion of BKL to mutex in commit 645ef9ef, the mutex
definition was put in a wrong place inside #ifdef WSND_DEBUG, which
leads to the build error. Just move it outside the ifdef.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If krealloc() returns NULL, it doesn't free the original. So any code
of the form 'foo = krealloc(foo, ...);' is almost certainly a bug.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
On systems with no package MSR support this caused crash as there
is a bug in the logic to check presence of DTHERM and PTS feature
together. Added a change so that when there is no PTS support, module
doesn't get loaded. Even if some CPU comes online with the PTS
feature disabled, and other CPUs has this support, this patch
will still prevent such MSR accesses.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Various regression and bug fixes for ext4"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't allow ext4_free_blocks() to fail due to ENOMEM
ext4: fix spelling errors and a comment in extent_status tree
ext4: rate limit printk in buffer_io_error()
ext4: don't show usrquota/grpquota twice in /proc/mounts
ext4: fix warning in ext4_evict_inode()
ext4: fix ext4_get_group_number()
ext4: silence warning in ext4_writepages()
|
|
Some callers of ext4_es_remove_extent() and ext4_es_insert_extent()
may not be completely robust against ENOMEM failures (or the
consequences of reflecting ENOMEM back up to userspace may lead to
xfstest or user application failure).
To mitigate against this, when trying to insert an entry in the extent
status tree, try to shrink the inode's extent status tree before
returning ENOMEM. If there are entries which don't record information
about extents under delayed allocations, freeing one of them is
preferable to returning ENOMEM.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
|
|
In ext4_ext_map_blocks(), if we have successfully allocated the data
blocks, but then run into trouble inserting the extent into the extent
tree, most likely due to an ENOSPC condition, determine the arguments
to ext4_free_blocks() in a simpler way which is easier to prove to be
correct.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Previously ext4_ext_truncate() was ignoring potential error returns
from ext4_es_remove_extent() and ext4_ext_remove_space(). This can
lead to the on-diks extent tree and the extent status tree cache
getting out of sync, which is particuarlly bad, and can lead to file
system corruption and potential data loss.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
