| Age | Commit message (Collapse) | Author |
|---|
|
When a bad checksum is found and if the filesystem has a mirror of the
damaged data, we read the correct data from the mirror and writes it to
damaged blocks. This however, violates the sequential write constraints
of a zoned block device.
We can consider three methods to repair an IO failure in zoned filesystems:
(1) Reset and rewrite the damaged zone
(2) Allocate new device extent and replace the damaged device extent to
the new extent
(3) Relocate the corresponding block group
Method (1) is most similar to a behavior done with regular devices.
However, it also wipes non-damaged data in the same device extent, and
so it unnecessary degrades non-damaged data.
Method (2) is much like device replacing but done in the same device. It
is safe because it keeps the device extent until the replacing finish.
However, extending device replacing is non-trivial. It assumes
"src_dev->physical == dst_dev->physical". Also, the extent mapping
replacing function should be extended to support replacing device extent
position in one device.
Method (3) invokes relocation of the damaged block group and is
straightforward to implement. It relocates all the mirrored device
extents, so it potentially is a more costly operation than method (1) or
(2). But it relocates only used extents which reduce the total IO size.
Let's apply method (3) for now. In the future, we can extend device-replace
and apply method (2).
For protecting a block group gets relocated multiple time with multiple
IO errors, this commit introduces "relocating_repair" bit to show it's
now relocating to repair IO failures. Also it uses a new kthread
"btrfs-relocating-repair", not to block IO path with relocating process.
This commit also supports repairing in the scrub process.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently fallocate() is disabled on a zoned filesystem. Since current
relocation process relies on preallocation to move file data extents, it
must be handled differently.
On a zoned filesystem, we just truncate the inode to the size that we
wanted to pre-allocate. Then, we flush dirty pages on the file before
finishing the relocation process. run_delalloc_zoned() will handle all
the allocations and submit IOs to the underlying layers.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is 4/4 patch to implement device-replace on zoned filesystems.
Even after the copying is done, the write pointers of the source device
and the destination device may not be synchronized. For example, when
the last allocated extent is freed before device-replace process, the
extent is not copied, leaving a hole there.
Synchronize the write pointers by writing zeroes to the destination
device.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is 3/4 patch to implement device-replace on zoned filesystems.
This commit implements copying. To do this, it tracks the write pointer
during the device replace process. As device-replace's copy process is
smart enough to only copy used extents on the source device, we have to
fill the gap to honor the sequential write requirement in the target
device.
The device-replace process on zoned filesystems must copy or clone all
the extents in the source device exactly once. So, we need to ensure
allocations started just before the dev-replace process to have their
corresponding extent information in the B-trees.
finish_extent_writes_for_zoned() implements that functionality, which
basically is the removed code in the commit 042528f8d840 ("Btrfs: fix
block group remaining RO forever after error during device replace").
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is 2/4 patch to implement device replace for zoned filesystems.
In zoned mode, a block group must be either copied (from the source
device to the target device) or cloned (to both devices).
Implement the cloning part. If a block group targeted by an IO is marked
to copy, we should not clone the IO to the destination device, because
the block group is eventually copied by the replace process.
This commit also handles cloning of device reset.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is the 1/4 patch to support device-replace on zoned filesystems.
We have two types of IOs during the device replace process. One is an IO
to "copy" (by the scrub functions) all the device extents from the source
device to the destination device. The other one is an IO to "clone" (by
handle_ops_on_dev_replace()) new incoming write IOs from users to the
source device into the target device.
Cloning incoming IOs can break the sequential write rule in on target
device. When a write is mapped in the middle of a block group, the IO is
directed to the middle of a target device zone, which breaks the
sequential write requirement.
However, the cloning function cannot be disabled since incoming IOs
targeting already copied device extents must be cloned so that the IO is
executed on the target device.
We cannot use dev_replace->cursor_{left,right} to determine whether a bio
is going to a not yet copied region. Since we have a time gap between
finishing btrfs_scrub_dev() and rewriting the mapping tree in
btrfs_dev_replace_finishing(), we can have a newly allocated device extent
which is never cloned nor copied.
So the point is to copy only already existing device extents. This patch
introduces mark_block_group_to_copy() to mark existing block groups as a
target of copying. Then, handle_ops_on_dev_replace() and dev-replace can
check the flag to do their job.
Also, btrfs_finish_block_group_to_copy() will check if the copied stripe
is the last stripe in the block group. With the last stripe copied,
the to_copy flag is finally disabled. Afterwards we can safely clone
incoming IOs on this block group.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
On zoned filesystems, btrfs uses per-fs zoned_meta_io_lock to serialize
the metadata write IOs.
Even with this serialization, write bios sent from btree_write_cache_pages
can be reordered by async checksum workers as these workers are per CPU
and not per zone.
To preserve write bio ordering, we disable async metadata checksum on a
zoned filesystem. This does not result in lower performance with HDDs as
a single CPU core is fast enough to do checksum for a single zone write
stream with the maximum possible bandwidth of the device. If multiple
zones are being written simultaneously, HDD seek overhead lowers the
achievable maximum bandwidth, resulting again in a per zone checksum
serialization not affecting the performance.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When truncating a file, file buffers which have already been allocated
but not yet written may be truncated. Truncating these buffers could
cause breakage of a sequential write pattern in a block group if the
truncated blocks are for example followed by blocks allocated to another
file. To avoid this problem, always wait for write out of all unwritten
buffers before proceeding with the truncate execution.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We cannot use zone append for writing metadata, because the B-tree nodes
have references to each other using logical address. Without knowing
the address in advance, we cannot construct the tree in the first place.
So we need to serialize write IOs for metadata.
We cannot add a mutex around allocation and submission because metadata
blocks are allocated in an earlier stage to build up B-trees.
Add a zoned_meta_io_lock and hold it during metadata IO submission in
btree_write_cache_pages() to serialize IOs.
Furthermore, this adds a per-block group metadata IO submission pointer
"meta_write_pointer" to ensure sequential writing, which can break when
attempting to write back blocks in an unfinished transaction. If the
writing out failed because of a hole and the write out is for data
integrity (WB_SYNC_ALL), it returns EAGAIN.
A caller like fsync() code should handle this properly e.g. by falling
back to a full transaction commit.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If more than one IO is issued for one file extent, these IO can be
written to separate regions on a device. Since we cannot map one file
extent to such a separate area on a zoned filesystem, we need to follow
the "one IO == one ordered extent" rule.
The normal buffered, uncompressed and not pre-allocated write path (used
by cow_file_range()) sometimes does not follow this rule. It can write a
part of an ordered extent when specified a region to write e.g., when
its called from fdatasync().
Introduce a dedicated (uncompressed buffered) data write path for zoned
filesystems, that will COW the region and write it at once.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Likewise to buffered IO, enable zone append writing for direct IO when
its used on a zoned block device.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Enable zone append writing for zoned mode. When using zone append, a
bio is issued to the start of a target zone and the device decides to
place it inside the zone. Upon completion the device reports the actual
written position back to the host.
Three parts are necessary to enable zone append mode. First, modify the
bio to use REQ_OP_ZONE_APPEND in btrfs_submit_bio_hook() and adjust the
bi_sector to point the beginning of the zone.
Second, record the returned physical address (and disk/partno) to the
ordered extent in end_bio_extent_writepage() after the bio has been
completed. We cannot resolve the physical address to the logical address
because we can neither take locks nor allocate a buffer in this end_bio
context. So, we need to record the physical address to resolve it later
in btrfs_finish_ordered_io().
And finally, rewrite the logical addresses of the extent mapping and
checksum data according to the physical address using btrfs_rmap_block.
If the returned address matches the originally allocated address, we can
skip this rewriting process.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A following patch will add another caller of
btrfs_lookup_ordered_extent(), but from a bio's endio context.
btrfs_lookup_ordered_extent() uses spin_lock_irq() which unconditionally
disables interrupts. Change this to spin_lock_irqsave() so interrupts
aren't disabled and re-enabled unconditionally.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
On a zoned filesystem, cache if a block group is on a sequential write
only zone.
On sequential write only zones, we can use REQ_OP_ZONE_APPEND for
writing data, therefore provide btrfs_use_zone_append() to figure out if
IO is targeting a sequential write only zone and we can use
REQ_OP_ZONE_APPEND for data writing.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_rmap_block currently reverse-maps the physical addresses on all
devices to the corresponding logical addresses.
Extend the function to match to a specified device. The old functionality
of querying all devices is left intact by specifying NULL as target
device.
A block_device instead of a btrfs_device is passed into btrfs_rmap_block,
as this function is intended to reverse-map the result of a bio, which
only has a block_device.
Also export the function for later use.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
To ensure that an ordered extent maps to a contiguous region on disk, we
need to maintain a "one bio == one ordered extent" rule.
Ensure that constructing bio does not span more than an ordered extent.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
For a zone append write, the device decides the location the data is being
written to. Therefore we cannot ensure that two bios are written
consecutively on the device. In order to ensure that an ordered extent
maps to a contiguous region on disk, we need to maintain a "one bio ==
one ordered extent" rule.
Implement splitting of an ordered extent and extent map on bio submission
to adhere to the rule.
extract_ordered_extent() hooks into btrfs_submit_data_bio() and splits the
corresponding ordered extent so that the ordered extent's region fits into
one bio and the corresponding device limits.
Several sanity checks need to be done in extract_ordered_extent() e.g.
- We cannot split once end_bio'd ordered extent because we cannot divide
ordered->bytes_left for the split ones
- We do not expect a compressed ordered extent
- We should not have checksum list because we omit the list splitting.
Since the function is called before btrfs_wq_submit_bio() or
btrfs_csum_one_bio(), this should be always ensured.
We also need to split an extent map by creating a new one. If not,
unpin_extent_cache() complains about the difference between the start of
the extent map and the file's logical offset.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Zoned filesystems use REQ_OP_ZONE_APPEND bios for writing to actual
devices.
Let btrfs_end_bio() and btrfs_op be aware of it, by mapping
REQ_OP_ZONE_APPEND to BTRFS_MAP_WRITE and using btrfs_op() instead of
bio_op().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A zoned device has its own hardware restrictions e.g. max_zone_append_size
when using REQ_OP_ZONE_APPEND. To follow these restrictions, use
bio_add_zone_append_page() instead of bio_add_page(). We need target device
to use bio_add_zone_append_page(), so this commit reads the chunk
information to cache the target device to btrfs_io_bio(bio)->device.
Caching only the target device is sufficient here as zoned filesystems
only supports the single profile at the moment. Once more profiles will be
supported btrfs_io_bio can hold an extent_map to be able to check for the
restrictions of all devices the btrfs_bio will be mapped to.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Factor out adding a page to a bio from submit_extent_page(). The page
is added only when bio_flags are the same, contiguous and the added page
fits in the same stripe as pages in the bio.
Condition checks are reordered to allow early return to avoid possibly
heavy btrfs_bio_fits_in_stripe() calling.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We must reset the zones of a deleted unused block group to rewind the
zones' write pointers to the zones' start.
To do this, we can use the DISCARD_SYNC code to do the reset when the
filesystem is running on zoned devices.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Since the allocation info of a tree log node is not recorded in the extent
tree, calculate_alloc_pointer() cannot detect this node, so the pointer
can be over a tree node.
Replaying the log calls btrfs_remove_free_space() for each node in the
log tree.
So, advance the pointer after the node to not allocate over it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Tree manipulating operations like merging nodes often release
once-allocated tree nodes. Such nodes are cleaned so that pages in the
node are not uselessly written out. On zoned volumes, however, such
optimization blocks the following IOs as the cancellation of the write
out of the freed blocks breaks the sequential write sequence expected by
the device.
Introduce a list of clean and unwritten extent buffers that have been
released in a transaction. Redirty the buffers so that
btree_write_cache_pages() can send proper bios to the devices.
Besides it clears the entire content of the extent buffer not to confuse
raw block scanners e.g. 'btrfs check'. By clearing the content,
csum_dirty_buffer() complains about bytenr mismatch, so avoid the
checking and checksum using newly introduced buffer flag
EXTENT_BUFFER_NO_CHECK.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Implement a sequential extent allocator for zoned filesystems. This
allocator only needs to check if there is enough space in the block group
after the allocation pointer to satisfy the extent allocation request.
Therefore the allocator never manages bitmaps or clusters. Also, add
assertions to the corresponding functions.
As zone append writing is used, it would be unnecessary to track the
allocation offset, as the allocator only needs to check available space.
But by tracking and returning the offset as an allocated region, we can
skip modification of ordered extents and checksum information when there
is no IO reordering.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In a zoned filesystem a once written then freed region is not usable
until the underlying zone has been reset. So we need to distinguish such
unusable space from usable free space.
Therefore we need to introduce the "zone_unusable" field to the block
group structure, and "bytes_zone_unusable" to the space_info structure
to track the unusable space.
Pinned bytes are always reclaimed to the unusable space. But, when an
allocated region is returned before using e.g., the block group becomes
read-only between allocation time and reservation time, we can safely
return the region to the block group. For the situation, this commit
introduces "btrfs_add_free_space_unused". This behaves the same as
btrfs_add_free_space() on regular filesystem. On zoned filesystems, it
rewinds the allocation offset.
Because the read-only bytes tracks free but unusable bytes when the block
group is read-only, we need to migrate the zone_unusable bytes to
read-only bytes when a block group is marked read-only.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Conventional zones do not have a write pointer, so we cannot use it to
determine the allocation offset for sequential allocation if a block
group contains a conventional zone.
But instead, we can consider the end of the highest addressed extent in
the block group for the allocation offset.
For new block group, we cannot calculate the allocation offset by
consulting the extent tree, because it can cause deadlock by taking
extent buffer lock after chunk mutex, which is already taken in
btrfs_make_block_group(). Since it is a new block group anyways, we can
simply set the allocation offset to 0.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A zoned filesystem must allocate blocks at the zones' write pointer. The
device's write pointer position can be mapped to a logical address within
a block group. To facilitate this, add an "alloc_offset" to the
block-group to track the logical addresses of the write pointer.
This logical address is populated in btrfs_load_block_group_zone_info()
from the write pointers of corresponding zones.
For now, zoned filesystems the single profile. Supporting non-single
profile with zone append writing is not trivial. For example, in the DUP
profile, we send a zone append writing IO to two zones on a device. The
device reply with written LBAs for the IOs. If the offsets of the
returned addresses from the beginning of the zone are different, then it
results in different logical addresses.
We need fine-grained logical to physical mapping to support such separated
physical address issue. Since it should require additional metadata type,
disable non-single profiles for now.
This commit supports the case all the zones in a block group are
sequential. The next patch will handle the case having a conventional
zone.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Add a check in verify_one_dev_extent() to ensure that a device extent on
a zoned block device is aligned to the respective zone boundary.
If it isn't, mark the filesystem as unclean.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Implement a zoned chunk and device extent allocator. One device zone
becomes a device extent so that a zone reset affects only this device
extent and does not change the state of blocks in the neighbor device
extents.
To implement the allocator, we need to extend the following functions for
a zoned filesystem.
- init_alloc_chunk_ctl
- dev_extent_search_start
- dev_extent_hole_check
- decide_stripe_size
init_alloc_chunk_ctl_zoned() is mostly the same as regular one. It always
set the stripe_size to the zone size and aligns the parameters to the zone
size.
dev_extent_search_start() only aligns the start offset to zone boundaries.
We don't care about the first 1MB like in regular filesystem because we
anyway reserve the first two zones for superblock logging.
dev_extent_hole_check_zoned() checks if zones in given hole are either
conventional or empty sequential zones. Also, it skips zones reserved for
superblock logging.
With the change to the hole, the new hole may now contain pending extents.
So, in this case, loop again to check that.
Finally, decide_stripe_size_zoned() should shrink the number of devices
instead of stripe size because we need to honor stripe_size == zone_size.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Run a zoned filesystem on non-zoned devices. This is done by "slicing up"
the block device into static sized chunks and fake a conventional zone on
each of them. The emulated zone size is determined from the size of device
extent.
This is mainly aimed at testing of zoned filesystems, i.e. the zoned
chunk allocator, on regular block devices.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The implementation of fitrim depends on space cache, which is not used
and disabled for zoned extent allocator. So the current code does not
work with zoned filesystem.
In the future, we can implement fitrim for zoned filesystems by enabling
space cache (but, only for fitrim) or scanning the extent tree at fitrim
time. For now, disallow fitrim on zoned filesystems.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Don't set the zoned flag in fs_info as soon as we're encountering the
incompat filesystem flag for a zoned filesystem on mount. The zoned flag
in fs_info is in a union together with the zone_size, so setting it too
early will result in setting an incorrect zone_size as well.
Once the correct zone_size is read from the device, we can rely on the
zoned flag in fs_info as well to determine if the filesystem is zoned.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Since we have no write pointer in conventional zones, we cannot
determine the allocation offset from it. Instead, we set the allocation
offset after the highest addressed extent. This is done by reading the
extent tree in btrfs_load_block_group_zone_info().
However, this function is called from btrfs_read_block_groups(), so the
read lock for the tree node could be recursively taken.
To avoid this unsafe locking scenario, release the path before reading
the extent tree to get the allocation offset.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A zoned filesystem currently has a superblock at the beginning of the
superblock logging zones if the zones are conventional. This difference
in superblock position causes a chicken-and-egg problem for filesystems
with emulated zones. Since the device is a regular (non-zoned) device,
we cannot know if the filesystem is regular or zoned while reading the
superblock. But, to load the superblock, we need to see if it is
emulated zoned or not.
Place the superblocks at the same location as they are on regular
filesystem on regular devices to solve the problem. It is possible
because it's ensured that all the superblock locations are at an
(emulated) conventional zone on regular devices.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is a preparation patch to implement zone emulation on a regular
device.
To emulate a zoned filesystem on a regular (non-zoned) device, we need to
decide an emulated zone size. Instead of making it a compile-time static
value, we'll make it configurable at mkfs time. Since we have one zone ==
one device extent restriction, we can determine the emulated zone size
from the size of a device extent. We can extend btrfs_get_dev_zone_info()
to show a regular device filled with conventional zones once the zone size
is decided.
The current call site of btrfs_get_dev_zone_info() during the mount process
is earlier than loading the file system trees so that we don't know the
size of a device extent at this point. Thus we can't slice a regular device
to conventional zones.
This patch introduces btrfs_get_dev_zone_info_all_devices to load the zone
info for all the devices. And, it places this function in open_ctree()
after loading the trees.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When attempting to link XDP prog with MTU larger than supported,
user is not informed why XDP linking fails. Adding proper
error message: "MTU too large to enable XDP".
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Consolidate the actions performed on the packet based on the XDP
program result into a separate function that is easier to read and
maintain. Simplify the i40e_construct_skb_zc function, so that the
input xdp buffer is always freed, regardless of whether the output
skb is successfully created or not. Simplify the behavior of the
i40e_clean_rx_irq_zc function, so that the current packet descriptor
is dropped when function i40_construct_skb_zc returns an error as
opposed to re-processing the same description on the next invocation.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For performance reasons, remove the redundant buffer info updates
(*bi = NULL). The buffers ready to be cleaned can easily be tracked
based on the ring next-to-clean variable, which is consistently
updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For performance reasons, remove the redundant updates of the cleaned_count
variable, as its value can be computed based on the ring next-to-clean
variable, which is consistently updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For performance reasons, avoid writing the ring next-to-clean pointer
value back to memory on every update, as it is not really necessary.
Instead, simply read it at initialization into a local copy, update
the local copy as necessary and write the local copy back to memory
after the last update.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
net: Add support for route offload failure notifications
Ido Schimmel says:
====================
This is a complementary series to the one merged in commit 389cb1ecc86e
("Merge branch 'add-notifications-when-route-hardware-flags-change'").
The previous series added RTM_NEWROUTE notifications to user space
whenever a route was successfully installed in hardware or when its
state in hardware changed. This allows routing daemons to delay
advertisement of routes until they are installed in hardware.
However, if route installation failed, a routing daemon will wait
indefinitely for a notification that will never come. The aim of this
series is to provide a failure notification via a new flag
(RTM_F_OFFLOAD_FAILED) in the RTM_NEWROUTE message. Upon such a
notification a routing daemon may decide to withdraw the route from the
FIB.
Series overview:
Patch #1 adds the new RTM_F_OFFLOAD_FAILED flag
Patches #2-#3 and #4-#5 add failure notifications to IPv4 and IPv6,
respectively
Patches #6-#8 teach netdevsim to fail route installation via a new knob
in debugfs
Patch #9 extends mlxsw to mark routes with the new flag
Patch #10 adds test cases for the new notification over netdevsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add cases to verify that when debugfs variable "fail_route_offload" is
set, notification with "rt_offload_failed" flag is received.
Extend the existing cases to verify that when sysctl
"fib_notify_on_flag_change" is set to 2, the kernel emits notifications
only for failed route installation.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv4 route offload failed [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
TEST: IPv6 route offload failed [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When FIB_EVENT_ENTRY_{REPLACE, APPEND} are triggered and route insertion
fails, FIB abort is triggered.
After aborting, set the appropriate hardware flag to make the kernel emit
RTM_NEWROUTE notification with RTM_F_OFFLOAD_FAILED flag.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add "fail_route_offload" flag to disallow offloading routes.
It is needed to test "offload failed" notifications.
Create the flag as part of nsim_fib_create() under fib directory and set
it to false by default.
When FIB_EVENT_ENTRY_{REPLACE, APPEND} are triggered and
"fail_route_offload" value is true, set the appropriate hardware flag to
make the kernel emit RTM_NEWROUTE notification with RTM_F_OFFLOAD_FAILED
flag.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the dummy FIB offload module after debugfs, so that the FIB
module could create its own directory there.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will add the ability to fail route offload controlled by
debugfs variable called "fail_route_offload".
If we vetoed the addition, we might get a delete or append notification
for a route we do not have. Therefore, do not warn if route was not found.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv6 routes, so that
users will have better visibility into the offload process.
'struct fib6_info' is extended with new field that indicates if route
offload failed. Note that the new field is added using unused bit and
therefore there is no need to increase struct size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv4 routes, so that
users will have better visibility into the offload process.
'struct fib_alias', and 'struct fib_rt_info' are extended with new field
that indicates if route offload failed. Note that the new field is added
using unused bit and therefore there is no need to increase structs size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
