summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2022-04-25spi: cadence-quadspi: drop cqspi_set_protocol()Matthias Schiffer
As suggested, this removes the whole cqspi_set_protocol() function, as it is not actually needed: - Checks for unsupported operations are already handled by supports_op(), removing the need to distinguish DTR and non-DTR modes in the buswidth setup - supports_op() ensures that the DTR flags match for all relevant parts of an operation, so op->cmd.dtr can be used instead of copying the flag to the cqspi_flash_pdata - The logic in cqspi_set_protocol() is moved to cqspi_calc_rdreg() and cqspi_write_setup() (with a helper macro CQSPI_OP_WIDTH()) The helper macro checks nbytes instead of buswidth for 0, for consistency with supports_op() etc. Suggested-by: Pratyush Yadav <p.yadav@ti.com> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Link: https://lore.kernel.org/r/20220420155616.281730-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: spi-tegra20-sflash: using pm_runtime_resume_and_get instead of ↵Minghao Chi
pm_runtime_get_sync Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220418110103.2558955-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: rockchip: fix missing error on unsupported SPI_CS_HIGHLuca Ceresoli
The hardware (except for the ROCKCHIP_SPI_VER2_TYPE2 version) does not support active-high native chip selects. However if such a CS is configured the core does not error as it normally should, because the 'ctlr->use_gpio_descriptors = true' line in rockchip_spi_probe() makes the core set SPI_CS_HIGH in ctlr->mode_bits. In such a case the spi-rockchip driver operates normally but produces an active-low chip select signal without notice. There is no provision in the current core code to handle this situation. Fix by adding a check in the ctlr->setup function (similarly to what spi-atmel.c does). This cannot be done reading the SPI_CS_HIGH but in ctlr->mode_bits because that bit gets always set by the core for master mode (see above). Fixes: eb1262e3cc8b ("spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods") Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Link: https://lore.kernel.org/r/20220421213251.1077899-1-luca.ceresoli@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: spi-omap2-mcspi: using pm_runtime_resume_and_get instead of ↵Minghao Chi
pm_runtime_get_sync Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220414085433.2541670-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: mxs: using pm_runtime_resume_and_get instead of pm_runtime_get_syncMinghao Chi
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220420090420.2588868-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: spi-imx: using pm_runtime_resume_and_get instead of pm_runtime_get_syncMinghao Chi
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220414085343.2541608-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: spi-sprd: using pm_runtime_resume_and_get instead of pm_runtime_get_syncMinghao Chi
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220414085506.2541732-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: ingenic: Add support for new Ingenic SoCs.周琰杰 (Zhou Yanjie)
1.Since it would be dangerous to specify a newer SoC's compatible string as the fallback of an older SoC's compatible string, we add support for the "ingenic,jz4775-spi" compatible string in the driver. This will permit to support the JZ4775 by having: compatible = "ingenic,jz4775-spi"; Instead of doing: compatible = "ingenic,jz4775-spi", "ingenic,jz4780-spi"; 2.Add support for probing the spi-ingenic driver on the X1000 SoC from Ingenic. From the X1000 SoC onwards, the maximum frequency allowed by the SSI module of Ingenic SoCs has been changed from 54MHz to 50MHz. So "max_speed_hz" is introduced in "jz_soc_info" to set different maximum frequency values. 3.Add support for probing the spi-ingenic driver on the X2000 SoC from Ingenic. The X2000 SoC has only one native chip select line, so "max_native_cs" is introduced in "jz_soc_info" to set different maximum number of native chip select lines. 4.Because of the introduction of support for the X-series SoCs, the current driver is not only applicable to the JZ-series SoCs, so the description texts has been modified to avoid misunderstanding. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/1650724725-93758-4-git-send-email-zhouyanjie@wanyeetech.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: Add bindings for new Ingenic SoCs.周琰杰 (Zhou Yanjie)
Add the SPI bindings for the JZ4775 SoC, the X1000 SoC, and the X2000 SoC from Ingenic. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/1650724725-93758-3-git-send-email-zhouyanjie@wanyeetech.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25spi: ingenic: Add support for use GPIO as chip select line.周琰杰 (Zhou Yanjie)
Add support for using GPIOs as chip select lines on Ingenic SoCs. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/1650724725-93758-2-git-send-email-zhouyanjie@wanyeetech.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25regulator: richtek,rt4801: parse GPIOs per regulatorKrzysztof Kozlowski
Having one enable-gpios property for all regulators is discouraged and instead, similarly to regulator core ena_gpiod feature, each GPIO should be present in each regulator node. Add support for parsing such GPIOs, keeping backwards compatibility. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: ChiYuan Huang <cy_huang@richtek.com> Link: https://lore.kernel.org/r/20220425072455.27356-3-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod featureKrzysztof Kozlowski
The binding and driver duplicated regulator core feature of controlling regulators with GPIOs (of_parse_cb + ena_gpiod) and created its own enable-gpios property with multiple GPIOs. This is a less preferred way, because enable-gpios should enable only one element, not multiple. It also duplicates existing solution. Deprecate the original 'enable-gpios' and add per-regulator property. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220425072455.27356-2-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25regmap: cache: set max_register with reg_strideJeongtae Park
Current logic does not consider multi-stride cases, the max_register have to calculate with reg_stride because it is a kind of address range. Signed-off-by: Jeongtae Park <jtp.park@samsung.com> Link: https://lore.kernel.org/r/20220425114613.15934-1-jtp.park@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25ASoC: dmaengine: Restore NULL prepare_slave_config() callbackCodrin Ciubotariu
As pointed out by Sascha Hauer, this patch changes: if (pmc->config && !pcm->config->prepare_slave_config) <do nothing> to: if (pmc->config && !pcm->config->prepare_slave_config) snd_dmaengine_pcm_prepare_slave_config() This breaks the drivers that do not need a call to dmaengine_slave_config(). Drivers that still need to call snd_dmaengine_pcm_prepare_slave_config(), but have a NULL pcm->config->prepare_slave_config should use snd_dmaengine_pcm_prepare_slave_config() as their prepare_slave_config callback. Fixes: 9a1e13440a4f ("ASoC: dmaengine: do not use a NULL prepare_slave_config() callback") Reported-by: Sascha Hauer <sha@pengutronix.de> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220421125403.2180824-1-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25ASoC: atmel: mchp-pdmc: set prepare_slave_configCodrin Ciubotariu
Since a pointer to struct snd_dmaengine_pcm_config is passed, snd_dmaengine_pcm_prepare_slave_config() is no longer called unless it's explicitly set in prepare_slave_config. Fixes: 50291652af52 ("ASoC: atmel: mchp-pdmc: add PDMC driver") Suggested-by: Sascha Hauer <sha@pengutronix.de> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220421125403.2180824-2-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25ASoC: max98090: Generate notifications on changes for custom controlMark Brown
The max98090 driver has some custom controls which share a put() function which returns 0 unconditionally, meaning that events are not generated when the value changes. Fix that. Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20220420193454.2647908-2-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25ASoC: max98090: Reject invalid values in custom control put()Mark Brown
The max98090 driver has a custom put function for some controls which can only be updated in certain circumstances which makes no effort to validate that input is suitable for the control, allowing out of spec values to be written to the hardware and presented to userspace. Fix this by returning an error when invalid values are written. Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20220420193454.2647908-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-25timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick ↵Nicholas Piggin
is stopped When tick_nohz_stop_tick() stops the tick and high resolution timers are disabled, then the clock event device is not put into ONESHOT_STOPPED mode. This can lead to spurious timer interrupts with some clock event device drivers that don't shut down entirely after firing. Eliminate these by putting the device into ONESHOT_STOPPED mode at points where it is not being reprogrammed. When there are no timers active, then tick_program_event() with KTIME_MAX can be used to stop the device. When there is a timer active, the device can be stopped at the next tick (any new timer added by timers will reprogram the tick). Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220422141446.915024-1-npiggin@gmail.com
2022-04-25m68k: defconfig: Update defconfigs for v5.18-rc1Geert Uytterhoeven
- Drop CONFIG_BINFMT_AOUT=m (no longer available since commit 19e8b701e258701b ("a.out: Stop building a.out/osf1 support on alpha and m68k")), - Enable modular build of the SM3 digest algorithm (no longer auto-selected since commit 114004696bf23499 ("crypto: sm2 - make dependent on sm3 library")), - Drop CONFIG_CRC64=m (auto-selected since commit a7d4383f17e10f33 ("block: add pi for extended integrity")), - Drop CONFIG_TEST_OVERFLOW=m (replaced by auto-modular CONFIG_OVERFLOW_KUNIT_TEST in commit 617f55e20743fc50 ("lib: overflow: Convert to Kunit")), - Drop CONFIG_TEST_STACKINIT=m (replaced by auto-modular CONFIG_STACKINIT_KUNIT_TEST in commit 02788ebcf521fe78 ("lib: stackinit: Convert to KUnit")). Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Link: https://lore.kernel.org/r/2ca38d8de70fc9fad5ad17fb81d04736effa181d.1649066720.git.geert@linux-m68k.org
2022-04-25s390: add KCSAN instrumentation to barriers and spinlocksIlya Leoshkevich
test_barrier fails on s390 because of the missing KCSAN instrumentation for several synchronization primitives. Add it to barriers by defining __mb(), __rmb(), __wmb(), __dma_rmb() and __dma_wmb(), and letting the common code in asm-generic/barrier.h do the rest. Spinlocks require instrumentation only on the unlock path; notify KCSAN that the CPU cannot move memory accesses outside of the spin lock. In reality it also cannot move stores inside of it, but this is not important and can be omitted. Reported-by: Tobias Huschle <huschle@linux.ibm.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/pci: add error record for CC 2 retriesNiklas Schnelle
Currently it is not detectable from within Linux when PCI instructions are retried because of a busy condition. Detecting such conditions and especially how long they lasted can however be quite useful in problem determination. This patch enables this by adding an s390dbf error log when a CC 2 is first encountered as well as after the retried instruction. Despite being unlikely it may be possible that these added debug messages drown out important other messages so allow setting the debug level in zpci_err_insn*() and set their level to 1 so they can be filtered out if need be. Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/pci: add PCI access type and length to error recordsNiklas Schnelle
Currently when a PCI instruction returns a non-zero condition code it can be very hard to tell from the s390dbf logs what kind of instruction was executed. In case of PCI memory I/O (MIO) instructions it is even impossible to tell if we attempted a load, store or block store or how large the access was because only the address is logged. Improve this by adding an indicator byte for the instruction type to the error record and also store the length of the access for MIO instructions where this can not be deduced from the request. We use the following indicator values: - 'l': PCI load - 's': PCI store - 'b': PCI store block - 'L': PCI load (MIO) - 'S': PCI store (MIO) - 'B': PCI store block (MIO) - 'M': MPCIFC - 'R': RPCIT Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/pci: don't log availability events as errorsNiklas Schnelle
Availability events are logged in s390dbf in s390dbf/pci_error/hex_ascii even though they don't indicate an error condition. They have also become redundant as commit 6526a597a2e85 ("s390/pci: add simpler s390dbf traces for events") added an s390dbf/pci_msg/sprintf log entry for availability events which contains all non reserved fields of struct zpci_ccdf_avail. On the other hand the availability entries in the error log make it easy to miss actual errors and may even overwrite error entries if the message buffer wraps. Thus simply remove the availability events from the error log thereby establishing the rule that any content in s390dbf/pci_error indicates some kind of error. Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/pci: make better use of zpci_dbg() levelsNiklas Schnelle
While the zpci_dbg() macro offers a level parameter this is currently largely unused. The only instance with higher importance than 3 is the UID checking change debug message which is not actually more important as the UID uniqueness guarantee is already exposed in sysfs so this should rather be 3 as well. On the other hand the "add ..." message which shows what devices are visible at the lowest level is essential during problem determination. By setting its level to 1, lowering the debug level can act as a filter to only show the available functions. On the error side the default level is set to 6 while all existing messages are printed at level 0. This is inconsistent and means there is no room for having messages be invisible on the default level so instead set the default level to 3 like for errors matching the default for debug messages. Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/vfio-ap: remove superfluous MODULE_DEVICE_TABLE declarationThomas Huth
The vfio_ap module tries to register for the vfio_ap bus - but that's the interface that it provides itself, so this does not make much sense, thus let's simply drop this statement now. Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com> Link: https://lore.kernel.org/r/20220413094416.412114-1-thuth@redhat.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/vdso: add vdso randomizationSven Schnelle
Randomize the address of vdso if randomize_va_space is enabled. Note that this keeps the vdso address on the same PMD as the stack to avoid allocating an extra page table just for vdso. Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/vdso: map vdso above stackSven Schnelle
In the current code vdso is mapped below the stack. This is problematic when programs mapped to the top of the address space are allocating a lot of memory, because the heap will clash with the vdso. To avoid this map the vdso above the stack and move STACK_TOP so that it all fits into three level paging. Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/vdso: move vdso mapping to its own functionSven Schnelle
This is a preparation patch for adding vdso randomization to s390. It adds a function vdso_size(), which will be used later in calculating the STACK_TOP value. It also moves the vdso mapping into a new function vdso_map(), to keep the code similar to other architectures. Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/mmap: increase stack/mmap gap to 128MBSven Schnelle
This basically reverts commit 9e78a13bfb16 ("[S390] reduce miminum gap between stack and mmap_base"). 32MB is not enough space between stack and mmap for some programs. Given that compat task aren't common these days, lets revert back to 128MB. Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/zcrypt: code cleanupHarald Freudenberger
This patch tries to fix as much as possible of the checkpatch.pl --strict findings: CHECK: Logical continuations should be on the previous line CHECK: No space is necessary after a cast CHECK: Alignment should match open parenthesis CHECK: 'useable' may be misspelled - perhaps 'usable'? WARNING: Possible repeated word: 'is' CHECK: spaces preferred around that '*' (ctx:VxV) CHECK: Comparison to NULL could be written "!msg" CHECK: Prefer kzalloc(sizeof(*zc)...) over kzalloc(sizeof(struct...)...) CHECK: Unnecessary parentheses around resp_type->work CHECK: Avoid CamelCase: <xcRB> There is no functional change comming with this patch, only code cleanup, renaming, whitespaces, indenting, ... but no semantic change in any way. Also the API (zcrypt and pkey header file) is semantically unchanged. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/zcrypt: cleanup CPRB struct definitionsHarald Freudenberger
This patch does a little cleanup on the CPRBX struct in zcrypt.h and the redundant CPRB struct definition in zcrypt_msgtype6.c. Especially some of the misleading fields from the CPRBX struct have been removed. There is no semantic change coming with this patch. The field names changed in the XCRB struct are only related to reserved fields which should never been used. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/ap: uevent on apmask/aqpmask changeHarald Freudenberger
This patch introduces user space notifications for changes on the apmask or aqmask attributes. So it could be possible to write a udev rule to load/unload the vfio_ap kernel module based on changes of these masks. On chance of the apmask or aqmask an AP change event will be produced with an uevent environment variable showing the new APMASK or AQMASK mask. So a change on the apmask triggers an uvevent like this: KERNEL[490.160396] change /devices/ap (ap) ACTION=change DEVPATH=/devices/ap SUBSYSTEM=ap APMASK=0xffffffdfffffffffffffffffffffffffffffffffffffffffffffffffffffffff SEQNUM=13367 and a change on the aqmask looks like this: KERNEL[283.217642] change /devices/ap (ap) ACTION=change DEVPATH=/devices/ap SUBSYSTEM=ap AQMASK=0xfbffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff SEQNUM=13348 Only real changes to the masks are processed - the old and new masks are compared and no action is done if the values are equal (and thus no uevent). The emit of the uevent is the very last action done when a mask change is processed. However, there is no guarantee that all unbind/bind actions caused by the apmask/aqmask changes are completed when the apmask/aqmask change uevent is received in userspace. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Tested-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/cio: simplify the calculation of variablesHaowen Bai
Fix the following coccicheck warnings: ./arch/s390/include/asm/scsw.h:695:47-49: WARNING !A || A && B is equivalent to !A || B I apply a readable version just to get rid of a warning. Signed-off-by: Haowen Bai <baihaowen@meizu.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com> Link: https://lore.kernel.org/r/1649297808-5048-1-git-send-email-baihaowen@meizu.com Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Christian Borntraeger <borntraeger@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/smp: sort out physical vs virtual CPU0 lowcore pointerAlexander Gordeev
SPX instruction called from set_prefix() expects physical address of the lowcore to be installed, but instead the virtual address is passed. Note: this does not fix a bug currently, since virtual and physical addresses are identical. Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/zcrypt: add display of ASYM master key verification patternHarald Freudenberger
This patch extends the sysfs attribute mkvps for CCA cards to show the states and master key verification patterns for the old, current and new ASYM master key registers. With this patch now all relevant master key verification patterns related to a CCA HSM are available with the mkvps sysfs attribute. This is a requirement for some exploiters like the kubernetes cex plugin or initrd code needing to verify the master key verification patterns on HSMs before use. A sample output: cat /sys/devices/ap/card04/04.0005/mkvps AES NEW: empty 0x0000000000000000 AES CUR: valid 0xe9a49a58cd039bed AES OLD: valid 0x7d10d17bc8a409c4 APKA NEW: empty 0x0000000000000000 APKA CUR: valid 0x5f2f27aaa2d59b4a APKA OLD: valid 0x82a5e2cd5030d5ec ASYM NEW: empty 0x00000000000000000000000000000000 ASYM CUR: valid 0x650c25a89c27e716d0e692b6c83f10e5 ASYM OLD: valid 0xf8ae2acf8bfc57f0a0957c732c16078b Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Jörg Schmidbauer <jschmidb@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/kexec: set end-of-ipl flag in last diag308 callAlexander Egorenkov
If the facility IPL-complete-control is present then the last diag308 call made by kexec shall set the end-of-ipl flag in the subcode register to signal the hypervisor that this is the last diag308 call made by Linux. Only the diag308 calls made during a regular kexec need to set the end-of-ipl flag, in all other cases the hypervisor will ignore it. Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25s390/sclp: add detection of IPL-complete-control facilityAlexander Egorenkov
The presence of the IPL-complete-control facility can be derived from the hypervisor's SCLP info response. Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2022-04-25Revert "arm64: dts: tegra: Fix boolean properties with values"Arnd Bergmann
This reverts commit 1a67653de0dd, which caused a boot regression. The behavior of the "drive-push-pull" in the kernel does not match what the binding document describes. Revert Rob's patch to make the DT match the kernel again, rather than the binding. Link: https://lore.kernel.org/lkml/YlVAy95eF%2F9b1nmu@orome/ Reported-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-25tcp: make sure treq->af_specific is initializedEric Dumazet
syzbot complained about a recent change in TCP stack, hitting a NULL pointer [1] tcp request sockets have an af_specific pointer, which was used before the blamed change only for SYNACK generation in non SYNCOOKIE mode. tcp requests sockets momentarily created when third packet coming from client in SYNCOOKIE mode were not using treq->af_specific. Make sure this field is populated, in the same way normal TCP requests sockets do in tcp_conn_request(). [1] TCP: request_sock_TCPv6: Possible SYN flooding on port 20002. Sending cookies. Check SNMP counters. general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] CPU: 1 PID: 3695 Comm: syz-executor864 Not tainted 5.18.0-rc3-syzkaller-00224-g5fd1fe4807f9 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:tcp_create_openreq_child+0xe16/0x16b0 net/ipv4/tcp_minisocks.c:534 Code: 48 c1 ea 03 80 3c 02 00 0f 85 e5 07 00 00 4c 8b b3 28 01 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7e 08 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 c9 07 00 00 48 8b 3c 24 48 89 de 41 ff 56 08 48 RSP: 0018:ffffc90000de0588 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffff888076490330 RCX: 0000000000000100 RDX: 0000000000000001 RSI: ffffffff87d67ff0 RDI: 0000000000000008 RBP: ffff88806ee1c7f8 R08: 0000000000000000 R09: 0000000000000000 R10: ffffffff87d67f00 R11: 0000000000000000 R12: ffff88806ee1bfc0 R13: ffff88801b0e0368 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f517fe58700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffcead76960 CR3: 000000006f97b000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> tcp_v6_syn_recv_sock+0x199/0x23b0 net/ipv6/tcp_ipv6.c:1267 tcp_get_cookie_sock+0xc9/0x850 net/ipv4/syncookies.c:207 cookie_v6_check+0x15c3/0x2340 net/ipv6/syncookies.c:258 tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:1131 [inline] tcp_v6_do_rcv+0x1148/0x13b0 net/ipv6/tcp_ipv6.c:1486 tcp_v6_rcv+0x3305/0x3840 net/ipv6/tcp_ipv6.c:1725 ip6_protocol_deliver_rcu+0x2e9/0x1900 net/ipv6/ip6_input.c:422 ip6_input_finish+0x14c/0x2c0 net/ipv6/ip6_input.c:464 NF_HOOK include/linux/netfilter.h:307 [inline] NF_HOOK include/linux/netfilter.h:301 [inline] ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:473 dst_input include/net/dst.h:461 [inline] ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] NF_HOOK include/linux/netfilter.h:301 [inline] ipv6_rcv+0x27f/0x3b0 net/ipv6/ip6_input.c:297 __netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5405 __netif_receive_skb+0x24/0x1b0 net/core/dev.c:5519 process_backlog+0x3a0/0x7c0 net/core/dev.c:5847 __napi_poll+0xb3/0x6e0 net/core/dev.c:6413 napi_poll net/core/dev.c:6480 [inline] net_rx_action+0x8ec/0xc60 net/core/dev.c:6567 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558 invoke_softirq kernel/softirq.c:432 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649 sysvec_apic_timer_interrupt+0x93/0xc0 arch/x86/kernel/apic/apic.c:1097 Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWATEric Dumazet
I had this bug sitting for too long in my pile, it is time to fix it. Thanks to Doug Porter for reminding me of it! We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"), but the issue is that TCP stack currently only generates EPOLLOUT from input path, when tp->snd_una has advanced and skb(s) cleaned from rtx queue. If a flow has a big RTT, and/or receives SACKs, it is possible that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0 and no more data can be sent until tp->snd_una finally advances. What is needed is to also check if POLLOUT needs to be generated whenever tp->snd_nxt is advanced, from output path. This bug triggers more often after an idle period, as we do not receive ACK for at least one RTT. tcp_notsent_lowat could be a fraction of what CWND and pacing rate would allow to send during this RTT. In a followup patch, I will remove the bogus call to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED) from tcp_check_space(). Fact that we have decided to generate an EPOLLOUT does not mean the application has immediately refilled the transmit queue. This optimistic call might have been the reason the bug seemed not too serious. Tested: 200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2] $ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat $ cat bench_rr.sh SUM=0 for i in {1..10} do V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"` echo $V SUM=$(($SUM + $V)) done echo SUM=$SUM Before patch: $ bench_rr.sh 130000000 80000000 140000000 140000000 140000000 140000000 130000000 40000000 90000000 110000000 SUM=1140000000 After patch: $ bench_rr.sh 430000000 590000000 530000000 450000000 450000000 350000000 450000000 490000000 480000000 460000000 SUM=4680000000 # This is 410 % of the value before patch. Fixes: c9bee3b7fdec ("tcp: TCP_NOTSENT_LOWAT socket option") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Doug Porter <dsp@fb.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25net: mscc: ocelot: don't add VID 0 to ocelot->vlans when leaving VLAN-aware ↵Vladimir Oltean
bridge DSA, through dsa_port_bridge_leave(), first notifies the port of the fact that it left a bridge, then, if that bridge was VLAN-aware, it notifies the port of the change in VLAN awareness state, towards VLAN-unaware mode. So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on that port. In a way this structure correctly reflects the reality, but by design, VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge VLAN list of the driver, but managed separately. Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on several sanity checks that did not expect to have this VID there. For example, after we leave a VLAN-aware bridge and we re-join it, we can no longer program egress-tagged VLANs to hardware: # ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up # ip link set swp0 master br0 # ip link set swp0 nomaster # ip link set swp0 master br0 # bridge vlan add dev swp0 vid 100 Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs. But this configuration is in fact supported by the hardware, since we could use OCELOT_PORT_TAG_NATIVE. According to its comment: /* all VLANs except the native VLAN and VID 0 are egress-tagged */ yet when assessing the eligibility for this mode, we do not check for VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0 doesn't have a bridge VLAN structure. The way I identify the problem is that ocelot_port_vlan_filtering(false) only means to call ocelot_add_vlan_unaware_pvid() when we dynamically turn off VLAN awareness for a bridge we are under, and the PVID changes from the bridge PVID to a reserved PVID based on the bridge number. Since OCELOT_STANDALONE_PVID is statically added to the VLAN table during ocelot_vlan_init() and never removed afterwards, calling ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve any purpose. Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0) when we're resetting VLAN awareness after leaving the bridge, to become a standalone port. Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25net: mscc: ocelot: ignore VID 0 added by 8021q moduleVladimir Oltean
Both the felix DSA driver and ocelot switchdev driver declare dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*, so the 8021q module will add VID 0 to our RX filter when the port goes up, to ensure 802.1p traffic is not dropped. We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which deliberately does not have a struct ocelot_bridge_vlan associated with it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init(). If we allow external calls to modify VID 0, we reach the following situation: # ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up # ip link set swp0 master br0 # ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false bridge vlan port vlan-id swp0 1 PVID Egress Untagged # the bridge also adds VID 1 br0 1 PVID Egress Untagged # bridge vlan add dev swp0 vid 100 untagged Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN. This configuration should have been accepted, because ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE. Yet it isn't, because we have an entry in ocelot->vlans which says VID 0 should be egress-tagged, something the hardware can't do. Fix this by suppressing additions/deletions on VID 0 and managing this VLAN exclusively using OCELOT_STANDALONE_PVID. *DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware bridge. Ocelot declares it unconditionally for some reason. Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25net: dsa: flood multicast to CPU when slave has IFF_PROMISCVladimir Oltean
Certain DSA switches can eliminate flooding to the CPU when none of the ports have the IFF_ALLMULTI or IFF_PROMISC flags set. This is done by synthesizing a call to dsa_port_bridge_flags() for the CPU port, a call which normally comes from the bridge driver via switchdev. The bridge port flags and IFF_PROMISC|IFF_ALLMULTI have slightly different semantics, and due to inattention/lack of proper testing, the IFF_PROMISC flag allows unknown unicast to be flooded to the CPU, but not unknown multicast. This must be fixed by setting both BR_FLOOD (unicast) and BR_MCAST_FLOOD in the synthesized dsa_port_bridge_flags() call, since IFF_PROMISC means that packets should not be filtered regardless of their MAC DA. Fixes: 7569459a52c9 ("net: dsa: manage flooding on the CPU ports") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25x86/mce: Add messages for panic errors in AMD's MCE gradingCarlos Bilbao
When a machine error is graded as PANIC by the AMD grading logic, the MCE handler calls mce_panic(). The notification chain does not come into effect so the AMD EDAC driver does not decode the errors. In these cases, the messages displayed to the user are more cryptic and miss information that might be relevant, like the context in which the error took place. Add messages to the grading logic for machine errors so that it is clear what error it was. [ bp: Massage commit message. ] Signed-off-by: Carlos Bilbao <carlos.bilbao@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com> Link: https://lore.kernel.org/r/20220405183212.354606-3-carlos.bilbao@amd.com
2022-04-25ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md modePeilin Ye
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the following sequence of events: 1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link add ... external". "ip" ignores "[o]seq" if "external" is specified, so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e. it uses lockless TX); 2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g. bpf_skb_set_tunnel_key() in an eBPF program attached to this device; 3. gre_fb_xmit() or __gre6_xmit() processes these skb's: gre_build_header(skb, tun_hlen, flags, protocol, tunnel_id_to_key32(tun_info->key.tun_id), (flags & TUNNEL_SEQ) ? htonl(tunnel->o_seqno++) : 0); ^^^^^^^^^^^^^^^^^ Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by making o_seqno atomic_t. As mentioned by Eric Dumazet in commit b790e01aee74 ("ip_gre: lockless xmit"), making o_seqno atomic_t increases "chance for packets being out of order at receiver" when NETIF_F_LLTX is on. Maybe a better fix would be: 1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if they want the kernel to allow sequencing of outgoing packets; 2. Reject all outgoing TUNNEL_SEQ packets if the device was not created with "oseq". Unfortunately, that would break userspace. We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us do it in separate patches to keep this fix minimal. Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 77a5196a804e ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25ip6_gre: Make o_seqno start from 0 in native modePeilin Ye
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in native mode. According to RFC 2890 2.2., "The first datagram is sent with a sequence number of 0." Fix it. It is worth mentioning that o_seqno already starts from 0 in collect_md mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(), where tunnel->o_seqno is passed to gre_build_header() before getting incremented. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25ip_gre: Make o_seqno start from 0 in native modePeilin Ye
For GRE and GRETAP devices, currently o_seqno starts from 1 in native mode. According to RFC 2890 2.2., "The first datagram is sent with a sequence number of 0." Fix it. It is worth mentioning that o_seqno already starts from 0 in collect_md mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to gre_build_header() before getting incremented. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25x86/mce: Simplify AMD severity grading logicCarlos Bilbao
The MCE handler needs to understand the severity of the machine errors to act accordingly. Simplify the AMD grading logic following a logic that closely resembles the descriptions of the public PPR documents. This will help include more fine-grained grading of errors in the future. [ bp: Touchups. ] Signed-off-by: Carlos Bilbao <carlos.bilbao@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com> Link: https://lore.kernel.org/r/20220405183212.354606-2-carlos.bilbao@amd.com
2022-04-25net: lan966x: fix a couple off by one bugsDan Carpenter
The lan966x->ports[] array has lan966x->num_phys_ports elements. These are assigned in lan966x_probe(). That means the > comparison should be changed to >=. The first off by one check is harmless but the second one could lead to an out of bounds access and a crash. Fixes: 5ccd66e01cbe ("net: lan966x: add support for interrupts from analyzer") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-25net/smc: sync err code when tcp connection was refusedliuyacan
In the current implementation, when TCP initiates a connection to an unavailable [ip,port], ECONNREFUSED will be stored in the TCP socket, but SMC will not. However, some apps (like curl) use getsockopt(,,SO_ERROR,,) to get the error information, which makes them miss the error message and behave strangely. Fixes: 50717a37db03 ("net/smc: nonblocking connect rework") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-21 10:20:44 +0000