| Age | Commit message (Collapse) | Author |
|---|
|
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few thousand such pages are usually left around due to the re-use of
L1 tables having been provided by the hypervisor (Dom0) or tool stack
(DomU). Set NX in the direct map variant, which needs to be done in L2
due to the dual use of the re-used L1s.
For x86_configure_nx() to actually do what it is supposed to do, call
get_cpu_cap() first. This was broken by commit 4763ed4d45 ("x86, mm:
Clean up and simplify NX enablement") when switching away from the
direct EFER read.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
This reverts commit 63dd00fa3e524c27cc0509190084ab147ecc8ae2.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e52 ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One fix for ulpi-node lookup at msm glue driver
|
|
Use the direction argument passed into begin_cpu_access
and end_cpu_access when calling the dma_sync_sg_for_cpu/device.
The actual cache primitive called depends on the direction
passed in.
Signed-off-by: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In trying to add support for drm_hwcomposer to HiKey,
I've needed to utilize the ION CMA heap, and I've noticed
problems with allocations on newer kernels failing.
It seems back with 204f672255c2 ("ion: Use CMA APIs directly"),
the ion_cma_heap code was modified to use the CMA API, but
kept the arguments as buffer lengths rather then number of pages.
This results in errors as we don't have enough pages in CMA to
satisfy the exaggerated requests.
This patch converts the ion_cma_heap CMA API usage to properly
request pages.
It also fixes a minor issue in the allocation where in the error
path, the cma_release is called with the buffer->size value which
hasn't yet been set.
Cc: Laura Abbott <labbott@redhat.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Fixes: 204f672255c2 ("staging: android: ion: Use CMA APIs directly")
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we have multiple modesets for different connectors
happening in parallel we could have a race on the RMW on these
shared registers.
This possibility was initially raised by Paulo when reviewing
commit '555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")'
but the original possibility comes from commit '5416d871136d
("drm/i915/skl: Set the eDP link rate on DPLL0")'. Or maybe
later when atomic commits entered into picture.
Apparently the discussion around this topic showed that the
right solution would be on serializing the atomic commits in
a way that we don't have the possibility of races here since
if that parallel modeset happenings apparently many other
things will be on fire.
Code is there since SKL and there was no report of issue,
but since we never looked back to that serialization possibility,
and also we don't have an igt case for that it is better to at
least protect this corner.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: 555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")
Fixes: 5416d871136d ("drm/i915/skl: Set the eDP link rate on DPLL0")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20171215224310.19103-1-rodrigo.vivi@intel.com
(cherry picked from commit 8edcda1266f93816fde77c9754f388ae0ae343fc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Just printk the string, or at least do not double up on the newlines!
Fixes: eef57324d926 ("drm/i915: setup bridge for HDMI LPE audio driver")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Jerome Anand <jerome.anand@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213182858.2159-1-chris@chris-wilson.co.uk
(cherry picked from commit 99cd05c43baac8ef56c20eb1776a15b02c81ccc3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If an rt5514-spi device is probed but the platform hasn't linked it in,
we might never fully request the SPI IRQ, nor configure the rt5514 DSP,
but we still might try to enable the SPI IRQ (enable_irq_wake()). This
is bad, and among other things, can cause the interrupt to trigger every
time we try to suspend the system (e.g., because the interrupt trigger
setting was never set properly).
Instead of setting our wakeup capabilities in the SPI driver probe
routine, let's wait until we've actually requested the IRQ.
Fixes issues seen on the "kevin" Chromebook (Samsung Chromebook Plus).
Fixes: 58f1c07d23cd ("ASoC: rt5514: Voice wakeup support.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/fix/doc', 'spi/fix/imx', 'spi/fix/rspi', 'spi/fix/sun4i' and 'spi/fix/xilinx' into spi-linus
|
|
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 8e55b6fd0660 ("staging: lustre: lnet: replace list_for_each
with list_for_each_entry") was intended to be an idempotent change,
but actually broke the behavior of ksocknal_add_peer() causing mounts to fail.
The fact that it caused an existing "route2 = NULL;" to become
redundant could have been a clue. The fact that the loop body
set the new loop variable to NULL might also have been a clue
The original code relied on "route2" being NULL if nothing was found.
The new code would always set route2 to a non-NULL value if the list
was empty, and would likely crash if the list was not empty.
Restore correct functionality by using code-flow rather the value of
"route2" to determine whether to use on old route, or to add a new one.
Fixes: 8e55b6fd0660 ("staging: lustre: lnet: replace list_for_each with list_for_each_entry")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This modem needs this quirk to operate. It produces timeouts when
resumed without reset.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip bind writes commands followed by random string when writing to
match_busid attribute in sysfs, caused by using full variable size
instead of string length.
Signed-off-by: Juan Zea <juan.zea@qindel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following static checker warnings:
The patch c6688ef9f297: "usbip: fix stub_rx: harden CMD_SUBMIT path
to handle malicious input" from Dec 7, 2017, leads to the following
static checker warning:
drivers/usb/usbip/stub_rx.c:346 get_pipe()
warn: impossible condition
'(pdu->u.cmd_submit.transfer_buffer_length > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
drivers/usb/usbip/stub_rx.c:486 stub_recv_cmd_submit()
warn: always true condition
'(pdu->u.cmd_submit.transfer_buffer_length <= ((~0 >> 1))) =>
(s32min-s32max <= s32max)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a45360f ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a45360f ("USB: core: Add type-specific length check of BOS descriptors")
Cc: linux-stable <stable@vger.kernel.org>
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.15 -rc
*) Fix device-tree node lookups in tegra xusb
*) Fix platform_get_irq_byname's error checking in cpcap-usb phy driver
*) Fix in rockchip-typec phy driver to balance pm_runtime_enable/disable
*) Fix compiler error in rcar-gen3-usb2 phy when USB is disabled
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for YUGA CLM920-NC5 PID 0x9625 USB modem to option
driver.
Interface layout:
0: QCDM/DIAG
1: ADB
2: MODEM
3: AT
4: RMNET
Signed-off-by: Taiyi Wu <taiyity.wu@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some regmap code looks redudant. So simplify it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since this i2smode also includes the setting of Network mode, it
should have it in the name. This patch also adds its MASK define.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The name fsl_ssi_rxtx_reg_val is too long to read comfortably.
So this patch shortens it by using an array (fsl_ssi_regvals,
renamed from fsl_ssi_reg_val). To do that, it also introduces
two macros (TX and RX) to replace the wrapper structure. This
will also help further cleanups.
Meanwhile, it unifies all local variable with the name "vals"
to get rid of the name "reg" -- could be confusing with "regs"
in the private struct for regmap.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simplify the variable name. This reduces one over-80-character line.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Shortens the variable name to save space, useful for dev_err outputs.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patches unifies the error message in the "failed to xxxx" format.
It also reduces the length of one line and adds spaces to an operator.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch just simply unifies the coding style.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch renames CCSR_SSI_xxx to REG_SSI_xxx and SSI_xxx_yyy style.
It also slightly reduces the length of them to save some space.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch refines the comments by:
1) Removing all out-of-date comments
2) Removing all not-so-useful comments
3) Unifying the styles of all comments
4) Shortening comments to be more conise
5) Adding comments to improve code readablity
6) Moving all register related comments to fsl_ssi.h
7) Adding comments to all register and field defines
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There should be no trouble to understand dev = pdev->dev.
This can save some space to have more print info or save
some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Shorten the private data structure to save some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 4c7f16d14a33 ("drm/sun4i: Fix TCON clock and regmap
initialization sequence") moved a bunch of logic around, but forgot to
update the gotos after the introduction of the err_free_dotclock label.
It means that if we fail later that the one introduced in that commit,
we'll just to the old label which isn't free the clock we created. This
will result in a breakage as soon as someone tries to do something with
that clock, since its resources will have been long reclaimed.
Cc: <stable@vger.kernel.org>
Fixes: 4c7f16d14a33 ("drm/sun4i: Fix TCON clock and regmap initialization sequence")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f83c1cebc731f0b4251f5ddd7b38c718cd79bb0b.1512662253.git-series.maxime.ripard@free-electrons.com
|
|
When we added the regulator support in commit 90c5d7cdae64 ("ARM: dts:
sun8i: a711: Add regulator support"), we also dropped the PMIC's
compatible. Since it's not in the PMIC DTSI, unlike most other PMIC
DTSI, it obviously wasn't probing anymore.
Re-add it so that everything works again.
Fixes: 90c5d7cdae64 ("ARM: dts: sun8i: a711: Add regulator support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Not only does this remove the need for the hexdump code in most
normal kernel builds (still there for the extra directory), but
it also removes the need to ship binary files, which apparently
is somewhat problematic, as Randy reported.
While at it, also add the generated files to clean-files.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit ca986ad9bcd3 (nl80211: allow multiple active scheduled scan
requests) removed WIPHY_FLAG_SUPPORTS_SCHED_SCAN but left the kerneldoc
description in place, leading to this docs-build warning:
./include/net/cfg80211.h:3278: warning: Excess enum value
'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' description in 'wiphy_flags'
Remove the line and gain a bit of peace.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver may sleep under a spinlock.
The function call path is:
hwsim_get_radio_nl (acquire the spinlock)
nlmsg_new(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the certs C code generation appends to the generated files,
which is most likely a leftover from commit 715a12334764 ("wireless:
don't write C files on failures"). This causes duplicate code in the
generated files if the certificates have their timestamps modified
between builds and thereby trigger the generation rules.
Fixes: 715a12334764 ("wireless: don't write C files on failures")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Same as in ieee80211_nullfunc_get, enable the TODS bit, otherwise the
nullfunc packet will not be handled in ap rx path.
(will be dropped in ieee80211_accept_frame()).
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit:
1959a60182f4 ("x86/dumpstack: Pin the target stack when dumping it")
changed the behavior of stack traces for zombies. Before that commit,
/proc/<pid>/stack reported the last execution path of the zombie before
it died:
[<ffffffff8105b877>] do_exit+0x6f7/0xa80
[<ffffffff8105bc79>] do_group_exit+0x39/0xa0
[<ffffffff8105bcf0>] __wake_up_parent+0x0/0x30
[<ffffffff8152dd09>] system_call_fastpath+0x16/0x1b
[<00007fd128f9c4f9>] 0x7fd128f9c4f9
[<ffffffffffffffff>] 0xffffffffffffffff
After the commit, it just reports an empty stack trace.
The new behavior is actually probably more correct. If the stack
refcount has gone down to zero, then the task has already gone through
do_exit() and isn't going to run anymore. The stack could be freed at
any time and is basically gone, so reporting an empty stack makes sense.
However, save_stack_trace_tsk_reliable() treats such a missing stack
condition as an error. That can cause livepatch transition stalls if
there are any unreaped zombies. Instead, just treat it as a reliable,
empty stack.
Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Fixes: af085d9084b4 ("stacktrace/x86: add function for detecting reliable stack traces")
Link: http://lkml.kernel.org/r/e4b09e630e99d0c1080528f0821fc9d9dbaeea82.1513631620.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
