| Age | Commit message (Collapse) | Author |
|---|
|
Commit a30a555d7435 ("spi: bcm2835: transform native-cs to gpio-cs on
first spi_setup") disabled the use of hardware-controlled native Chip
Select in favour of software-controlled GPIO Chip Select but left code
to support the former untouched. Remove it to simplify the driver and
ease the addition of new features and further optimizations.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
If a DMA transfer finishes orderly right when spi_transfer_one_message()
determines that it has timed out, the callbacks bcm2835_spi_dma_done()
and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(),
potentially leading to double termination.
Prevent by atomically changing the dma_pending flag before calling
dmaengine_terminate_all().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If submission of a DMA TX transfer succeeds but submission of the
corresponding RX transfer does not, the BCM2835 SPI driver terminates
the TX transfer but neglects to reset the dma_pending flag to false.
Thus, if the next transfer uses interrupt mode (because it is shorter
than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout,
dmaengine_terminate_all() will be called both for TX (once more) and
for RX (which was never started in the first place). Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IRQ handler bcm2835_spi_interrupt() first reads as much as possible
from the RX FIFO, then writes as much as possible to the TX FIFO.
Afterwards it decides whether the transfer is finished by checking if
the TX FIFO is empty.
If very few bytes were written to the TX FIFO, they may already have
been transmitted by the time the FIFO's emptiness is checked. As a
result, the transfer will be declared finished and the chip will be
reset without reading the corresponding received bytes from the RX FIFO.
The odds of this happening increase with a high clock frequency (such
that the TX FIFO drains quickly) and either passing "threadirqs" on the
command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ
handler may be preempted between filling the TX FIFO and checking its
emptiness).
Fix by instead checking whether rx_len has reached zero, which means
that the transfer has been received in full. This is also more
efficient as it avoids one bus read access per interrupt. Note that
bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine
whether the transfer has finished.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: e34ff011c70e ("spi: bcm2835: move to the transfer_one driver model")
Cc: stable@vger.kernel.org # v4.1+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introducing a module param for wakeup_delay in order to
align with modeswitch_delay parameter. With this change, both
wakeup_delay and modeswitch_delay parameters can be passed
as module parameters.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On startup, applications such as PulseAudio or CRAS enable playback or
capture on all PCM devices to verify that configurations are correct,
and close them immediately. For DMICs, this can result in the clock
being turned off very quickly, which may not compatible with internal
state machine transition requirements.
This patch add a mode-switch delay which will prevent the clock from
being turned off without complying with manufacturer timing
specifications. While the DMIC clock may be controlled at a lower level,
be it with hardware or firmware, applying the delay during the
STOP_TRIGGER phase ensures that there is no race condition, e.g. with
the hardware/firmware turning off the clock earlier
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McPDM module receives it's functional clock from external source. This
clock is the pdmclk provided by the twl6040 audio IC. If the clock is not
available all register accesses to McPDM fails and the module is not
operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a callback for init ops on dai_link to create and setup jack.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add board specific dapm widgets so these widgets can be used
in the route.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
[Description]
In a heavily loaded system where the system pagecache is nearing memory
limits and fscache is enabled, pages can be leaked by fscache while trying
read pages from cachefiles backend. This can happen because two
applications can be reading same page from a single mount, two threads can
be trying to read the backing page at same time. This results in one of
the threads finding that a page for the backing file or netfs file is
already in the radix tree. During the error handling cachefiles does not
clean up the reference on backing page, leading to page leak.
[Fix]
The fix is straightforward, to decrement the reference when error is
encountered.
[dhowells: Note that I've removed the clearance and put of newpage as
they aren't attested in the commit message and don't appear to actually
achieve anything since a new page is only allocated is newpage!=NULL and
any residual new page is cleared before returning.]
[Testing]
I have tested the fix using following method for 12+ hrs.
1) mkdir -p /mnt/nfs ; mount -o vers=3,fsc <server_ip>:/export /mnt/nfs
2) create 10000 files of 2.8MB in a NFS mount.
3) start a thread to simulate heavy VM presssure
(while true ; do echo 3 > /proc/sys/vm/drop_caches ; sleep 1 ; done)&
4) start multiple parallel reader for data set at same time
find /mnt/nfs -type f | xargs -P 80 cat > /dev/null &
find /mnt/nfs -type f | xargs -P 80 cat > /dev/null &
find /mnt/nfs -type f | xargs -P 80 cat > /dev/null &
..
..
find /mnt/nfs -type f | xargs -P 80 cat > /dev/null &
find /mnt/nfs -type f | xargs -P 80 cat > /dev/null &
5) finally check using cat /proc/fs/fscache/stats | grep -i pages ;
free -h , cat /proc/meminfo and page-types -r -b lru
to ensure all pages are freed.
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Shantanu Goel <sgoel01@yahoo.com>
Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com>
[dja: forward ported to current upstream]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Fix the size of the buffer allocated to store the in-memory BBT.
This bug was previously hidden by a different bug, that was fixed in
commit d098093ba06e ("mtd: nand: Fix nanddev_neraseblocks()").
Fixes: 9c3736a3de21 ("mtd: nand: Add core infrastructure to deal with NAND devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The code in fscache_retrieval_complete is using atomic_sub followed by an
atomic_read:
atomic_sub(n_pages, &op->n_pages);
if (atomic_read(&op->n_pages) <= 0)
fscache_op_complete(&op->op, true);
This causes two threads doing a decrement of n_pages to race with each
other seeing the op->refcount 0 at same time - and they end up calling
fscache_op_complete() in both the threads leading to an assertion failure.
Fix this by using atomic_sub_return_relaxed() instead of two calls. Note
that I'm using 'relaxed' rather than, say, 'release' as there aren't
multiple variables that appear to need ordering across the release.
The oops looks something like:
FS-Cache: Assertion failed
FS-Cache: 0 > 0 is false
...
kernel BUG at /usr/src/linux-4.4.0/fs/fscache/operation.c:449!
...
Workqueue: fscache_operation fscache_op_work_func [fscache]
...
RIP: 0010:[<ffffffffc037eacd>] fscache_op_complete+0x10d/0x180 [fscache]
...
Call Trace:
[<ffffffffc1464cf9>] cachefiles_read_copier+0x3a9/0x410 [cachefiles]
[<ffffffffc037e272>] fscache_op_work_func+0x22/0x50 [fscache]
[<ffffffff81096da0>] process_one_work+0x150/0x3f0
[<ffffffff8109751a>] worker_thread+0x11a/0x470
[<ffffffff81808e59>] ? __schedule+0x359/0x980
[<ffffffff81097400>] ? rescuer_thread+0x310/0x310
[<ffffffff8109cdd6>] kthread+0xd6/0xf0
[<ffffffff8109cd00>] ? kthread_park+0x60/0x60
[<ffffffff8180d0cf>] ret_from_fork+0x3f/0x70
[<ffffffff8109cd00>] ? kthread_park+0x60/0x60
This seen this in 4.4.x kernels and the same bug affects fscache in latest
upstreams kernels.
Fixes: 1bb4b7f98f36 ("FS-Cache: The retrieval remaining-pages counter needs to be atomic_t")
Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
If cachefiles gets an error other then ENOENT when trying to look up an
object in the cache (in this case, EACCES), the object state machine will
eventually transition to the DROP_OBJECT state.
This state invokes fscache_drop_object() which tries to sync the auxiliary
data with the cache (this is done lazily since commit 402cb8dda949d) on an
incomplete cache object struct.
The problem comes when cachefiles_update_object_xattr() is called to
rewrite the xattr holding the data. There's an assertion there that the
cache object points to a dentry as we're going to update its xattr. The
assertion trips, however, as dentry didn't get set.
Fix the problem by skipping the update in cachefiles if the object doesn't
refer to a dentry. A better way to do it could be to skip the update from
the DROP_OBJECT state handler in fscache, but that might deny the cache the
opportunity to update intermediate state.
If this error occurs, the kernel log includes lines that look like the
following:
CacheFiles: Lookup failed error -13
CacheFiles:
CacheFiles: Assertion failed
------------[ cut here ]------------
kernel BUG at fs/cachefiles/xattr.c:138!
...
Workqueue: fscache_object fscache_object_work_func [fscache]
RIP: 0010:cachefiles_update_object_xattr.cold.4+0x18/0x1a [cachefiles]
...
Call Trace:
cachefiles_update_object+0xdd/0x1c0 [cachefiles]
fscache_update_aux_data+0x23/0x30 [fscache]
fscache_drop_object+0x18e/0x1c0 [fscache]
fscache_object_work_func+0x74/0x2b0 [fscache]
process_one_work+0x18d/0x340
worker_thread+0x2e/0x390
? pwq_unbound_release_workfn+0xd0/0xd0
kthread+0x112/0x130
? kthread_bind+0x30/0x30
ret_from_fork+0x35/0x40
Note that there are actually two issues here: (1) EACCES happened on a
cache object and (2) an oops occurred. I think that the second is a
consequence of the first (it certainly looks like it ought to be). This
patch only deals with the second.
Fixes: 402cb8dda949 ("fscache: Attach the index key and aux data to the cookie")
Reported-by: Zhibin Li <zhibli@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
If the dismod is specified in the DT node, use the specified custom value
to configure the drive on state of the inactive TX slots.
If the dismod is not present or booted in legacy mode, the dismod is set
to low as it was the original behavior.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dismod property can be used to specify the drive on level of inactive
TX slots.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When McASP is master and the PDIR for the clock pins are configured as
outputs before the clocking is configured it will output whatever clock
is generated at the moment internally.
The clock will switch to the correct rate only when the we start the clock
generators.
To avoid this we must only set the pin as output after the clock is
configured and enabled.
AXR pins configured as outputs behaves somehow interesting as well:
when McASP is not enabled and the pin is selected as output it will not
honor the DISMOD settings for the inactive state, but will pull the pin
down.
Add a new bitfield and mark the pins there which needs to be output and
set the pins only at the time when they will behave correctly.
On stream stop configure the pins back to input which makes them to obey
the global pin configuration regarding to pull up/down.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the guideline from the TRM:
Before starting, clear the respective transmitter and receiver status
registers
To avoid stale state stored in the status registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK
already running. Add these to the IPC reply lookup table.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add more meaning to the IPC replies for easy debugging. Replace the switch
case with a lookup table to lookup for the IPC replies and print in human
readable form.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds a new LED trigger for coupling the audio mixer change
with the LED on laptops or other devices. Currently there are two
trigger types, "audio-mute" and "audio-micmute".
The audio driver triggers the LED brightness change via
ledtrig_audio_set() call with the proper type (either mute or
mic-mute). OTOH, the consumers may call ledtrig_audio_get() for the
initial brightness value that may have been set by the audio driver
beforehand.
This new stuff will be used by HD-audio codec driver and some platform
drivers (thinkpad_acpi and dell-laptop, also upcoming huawei-wmi).
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Provide the possibility to enable IBPB always in combination with 'prctl'
and 'seccomp'.
Add the extra command line options and rework the IBPB selection to
evaluate the command instead of the mode selected by the STIPB switch case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185006.144047038@linutronix.de
|
|
If 'prctl' mode of user space protection from spectre v2 is selected
on the kernel command-line, STIBP and IBPB are applied on tasks which
restrict their indirect branch speculation via prctl.
SECCOMP enables the SSBD mitigation for sandboxed tasks already, so it
makes sense to prevent spectre v2 user space to user space attacks as
well.
The Intel mitigation guide documents how STIPB works:
Setting bit 1 (STIBP) of the IA32_SPEC_CTRL MSR on a logical processor
prevents the predicted targets of indirect branches on any logical
processor of that core from being controlled by software that executes
(or executed previously) on another logical processor of the same core.
Ergo setting STIBP protects the task itself from being attacked from a task
running on a different hyper-thread and protects the tasks running on
different hyper-threads from being attacked.
While the document suggests that the branch predictors are shielded between
the logical processors, the observed performance regressions suggest that
STIBP simply disables the branch predictor more or less completely. Of
course the document wording is vague, but the fact that there is also no
requirement for issuing IBPB when STIBP is used points clearly in that
direction. The kernel still issues IBPB even when STIBP is used until Intel
clarifies the whole mechanism.
IBPB is issued when the task switches out, so malicious sandbox code cannot
mistrain the branch predictor for the next user space task on the same
logical processor.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185006.051663132@linutronix.de
|
|
Now that all prerequisites are in place:
- Add the prctl command line option
- Default the 'auto' mode to 'prctl'
- When SMT state changes, update the static key which controls the
conditional STIBP evaluation on context switch.
- At init update the static key which controls the conditional IBPB
evaluation on context switch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.958421388@linutronix.de
|
|
Add the PR_SPEC_INDIRECT_BRANCH option for the PR_GET_SPECULATION_CTRL and
PR_SET_SPECULATION_CTRL prctls to allow fine grained per task control of
indirect branch speculation via STIBP and IBPB.
Invocations:
Check indirect branch speculation status with
- prctl(PR_GET_SPECULATION_CTRL, PR_SPEC_INDIRECT_BRANCH, 0, 0, 0);
Enable indirect branch speculation with
- prctl(PR_SET_SPECULATION_CTRL, PR_SPEC_INDIRECT_BRANCH, PR_SPEC_ENABLE, 0, 0);
Disable indirect branch speculation with
- prctl(PR_SET_SPECULATION_CTRL, PR_SPEC_INDIRECT_BRANCH, PR_SPEC_DISABLE, 0, 0);
Force disable indirect branch speculation with
- prctl(PR_SET_SPECULATION_CTRL, PR_SPEC_INDIRECT_BRANCH, PR_SPEC_FORCE_DISABLE, 0, 0);
See Documentation/userspace-api/spec_ctrl.rst.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.866780996@linutronix.de
|
|
The upcoming fine grained per task STIBP control needs to be updated on CPU
hotplug as well.
Split out the code which controls the strict mode so the prctl control code
can be added later. Mark the SMP function call argument __unused while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.759457117@linutronix.de
|
|
The seccomp speculation control operates on all tasks of a process, but
only the current task of a process can update the MSR immediately. For the
other threads the update is deferred to the next context switch.
This creates the following situation with Process A and B:
Process A task 2 and Process B task 1 are pinned on CPU1. Process A task 2
does not have the speculation control TIF bit set. Process B task 1 has the
speculation control TIF bit set.
CPU0 CPU1
MSR bit is set
ProcB.T1 schedules out
ProcA.T2 schedules in
MSR bit is cleared
ProcA.T1
seccomp_update()
set TIF bit on ProcA.T2
ProcB.T1 schedules in
MSR is not updated <-- FAIL
This happens because the context switch code tries to avoid the MSR update
if the speculation control TIF bits of the incoming and the outgoing task
are the same. In the worst case ProcB.T1 and ProcA.T2 are the only tasks
scheduling back and forth on CPU1, which keeps the MSR stale forever.
In theory this could be remedied by IPIs, but chasing the remote task which
could be migrated is complex and full of races.
The straight forward solution is to avoid the asychronous update of the TIF
bit and defer it to the next context switch. The speculation control state
is stored in task_struct::atomic_flags by the prctl and seccomp updates
already.
Add a new TIF_SPEC_FORCE_UPDATE bit and set this after updating the
atomic_flags. Check the bit on context switch and force a synchronous
update of the speculation control if set. Use the same mechanism for
updating the current task.
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1811272247140.1875@nanos.tec.linutronix.de
|
|
The update of the TIF_SSBD flag and the conditional speculation control MSR
update is done in the ssb_prctl_set() function directly. The upcoming prctl
support for controlling indirect branch speculation via STIBP needs the
same mechanism.
Split the code out and make it reusable. Reword the comment about updates
for other tasks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.652305076@linutronix.de
|
|
The IBPB control code in x86 removed the usage. Remove the functionality
which was introduced for this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.559149393@linutronix.de
|
|
The IBPB speculation barrier is issued from switch_mm() when the kernel
switches to a user space task with a different mm than the user space task
which ran last on the same CPU.
An additional optimization is to avoid IBPB when the incoming task can be
ptraced by the outgoing task. This optimization only works when switching
directly between two user space tasks. When switching from a kernel task to
a user space task the optimization fails because the previous task cannot
be accessed anymore. So for quite some scenarios the optimization is just
adding overhead.
The upcoming conditional IBPB support will issue IBPB only for user space
tasks which have the TIF_SPEC_IB bit set. This requires to handle the
following cases:
1) Switch from a user space task (potential attacker) which has
TIF_SPEC_IB set to a user space task (potential victim) which has
TIF_SPEC_IB not set.
2) Switch from a user space task (potential attacker) which has
TIF_SPEC_IB not set to a user space task (potential victim) which has
TIF_SPEC_IB set.
This needs to be optimized for the case where the IBPB can be avoided when
only kernel threads ran in between user space tasks which belong to the
same process.
The current check whether two tasks belong to the same context is using the
tasks context id. While correct, it's simpler to use the mm pointer because
it allows to mangle the TIF_SPEC_IB bit into it. The context id based
mechanism requires extra storage, which creates worse code.
When a task is scheduled out its TIF_SPEC_IB bit is mangled as bit 0 into
the per CPU storage which is used to track the last user space mm which was
running on a CPU. This bit can be used together with the TIF_SPEC_IB bit of
the incoming task to make the decision whether IBPB needs to be issued or
not to cover the two cases above.
As conditional IBPB is going to be the default, remove the dubious ptrace
check for the IBPB always case and simply issue IBPB always when the
process changes.
Move the storage to a different place in the struct as the original one
created a hole.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.466447057@linutronix.de
|
|
The TIF_SPEC_IB bit does not need to be evaluated in the decision to invoke
__switch_to_xtra() when:
- CONFIG_SMP is disabled
- The conditional STIPB mode is disabled
The TIF_SPEC_IB bit still controls IBPB in both cases so the TIF work mask
checks might invoke __switch_to_xtra() for nothing if TIF_SPEC_IB is the
only set bit in the work masks.
Optimize it out by masking the bit at compile time for CONFIG_SMP=n and at
run time when the static key controlling the conditional STIBP mode is
disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.374062201@linutronix.de
|
|
Move the conditional invocation of __switch_to_xtra() into an inline
function so the logic can be shared between 32 and 64 bit.
Remove the handthrough of the TSS pointer and retrieve the pointer directly
in the bitmap handling function. Use this_cpu_ptr() instead of the
per_cpu() indirection.
This is a preparatory change so integration of conditional indirect branch
speculation optimization happens only in one place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.280855518@linutronix.de
|
|
To avoid the overhead of STIBP always on, it's necessary to allow per task
control of STIBP.
Add a new task flag TIF_SPEC_IB and evaluate it during context switch if
SMT is active and flag evaluation is enabled by the speculation control
code. Add the conditional evaluation to x86_virt_spec_ctrl() as well so the
guest/host switch works properly.
This has no effect because TIF_SPEC_IB cannot be set yet and the static key
which controls evaluation is off. Preparatory patch for adding the control
code.
[ tglx: Simplify the context switch logic and make the TIF evaluation
depend on SMP=y and on the static key controlling the conditional
update. Rename it to TIF_SPEC_IB because it controls both STIBP and
IBPB ]
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.176917199@linutronix.de
|
|
Add command line control for user space indirect branch speculation
mitigations. The new option is: spectre_v2_user=
The initial options are:
- on: Unconditionally enabled
- off: Unconditionally disabled
-auto: Kernel selects mitigation (default off for now)
When the spectre_v2= command line argument is either 'on' or 'off' this
implies that the application to application control follows that state even
if a contradicting spectre_v2_user= argument is supplied.
Originally-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185005.082720373@linutronix.de
|
|
There is no point in having two functions and a conditional at the call
site.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.986890749@linutronix.de
|
|
No point to keep that around.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.893886356@linutronix.de
|
|
checkpatch.pl muttered when reshuffling the code:
WARNING: static const char * array should probably be static const char * const
Fix up all the string arrays.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.800018931@linutronix.de
|
|
Reorder the code so it is better grouped. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.707122879@linutronix.de
|
|
Use the now exposed real SMT state, not the SMT sysfs control knob
state. This reflects the state of the system when the mitigation status is
queried.
This does not change the warning in the VMX launch code. There the
dependency on the control knob makes sense because siblings could be
brought online anytime after launching the VM.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.613357354@linutronix.de
|
|
arch_smt_update() is only called when the sysfs SMT control knob is
changed. This means that when SMT is enabled in the sysfs control knob the
system is considered to have SMT active even if all siblings are offline.
To allow finegrained control of the speculation mitigations, the actual SMT
state is more interesting than the fact that siblings could be enabled.
Rework the code, so arch_smt_update() is invoked from each individual CPU
hotplug function, and simplify the update function while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.521974984@linutronix.de
|
|
Make the scheduler's 'sched_smt_present' static key globaly available, so
it can be used in the x86 speculation control code.
Provide a query function and a stub for the CONFIG_SMP=n case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.430168326@linutronix.de
|
|
CONFIG_SCHED_SMT is enabled by all distros, so there is not a real point to
have it configurable. The runtime overhead in the core scheduler code is
minimal because the actual SMT scheduling parts are conditional on a static
key.
This allows to expose the scheduler's SMT state static key to the
speculation control code. Alternatively the scheduler's static key could be
made always available when CONFIG_SMP is enabled, but that's just adding an
unused static key to every other architecture for nothing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.337452245@linutronix.de
|
|
Currently the 'sched_smt_present' static key is enabled when at CPU bringup
SMT topology is observed, but it is never disabled. However there is demand
to also disable the key when the topology changes such that there is no SMT
present anymore.
Implement this by making the key count the number of cores that have SMT
enabled.
In particular, the SMT topology bits are set before interrrupts are enabled
and similarly, are cleared after interrupts are disabled for the last time
and the CPU dies.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.246110444@linutronix.de
|
|
The logic to detect whether there's a change in the previous and next
task's flag relevant to update speculation control MSRs is spread out
across multiple functions.
Consolidate all checks needed for updating speculation control MSRs into
the new __speculation_ctrl_update() helper function.
This makes it easy to pick the right speculation control MSR and the bits
in MSR_IA32_SPEC_CTRL that need updating based on TIF flags changes.
Originally-by: Thomas Lendacky <Thomas.Lendacky@amd.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.151077005@linutronix.de
|
|
During context switch, the SSBD bit in SPEC_CTRL MSR is updated according
to changes of the TIF_SSBD flag in the current and next running task.
Currently, only the bit controlling speculative store bypass disable in
SPEC_CTRL MSR is updated and the related update functions all have
"speculative_store" or "ssb" in their names.
For enhanced mitigation control other bits in SPEC_CTRL MSR need to be
updated as well, which makes the SSB names inadequate.
Rename the "speculative_store*" functions to a more generic name. No
functional change.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185004.058866968@linutronix.de
|
|
If enhanced IBRS is active, STIBP is redundant for mitigating Spectre v2
user space exploits from hyperthread sibling.
Disable STIBP when enhanced IBRS is used.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185003.966801480@linutronix.de
|
|
The Spectre V2 printout in cpu_show_common() handles conditionals for the
various mitigation methods directly in the sprintf() argument list. That's
hard to read and will become unreadable if more complex decisions need to
be made for a particular method.
Move the conditionals for STIBP and IBPB string selection into helper
functions, so they can be extended later on.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185003.874479208@linutronix.de
|
|
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185003.783903657@linutronix.de
|
|
Remove the unnecessary 'else' statement in spectre_v2_parse_cmdline()
to save an indentation level.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185003.688010903@linutronix.de
|
|
"Reduced Data Speculation" is an obsolete term. The correct new name is
"Speculative store bypass disable" - which is abbreviated into SSBD.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Casey Schaufler <casey.schaufler@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Waiman Long <longman9394@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Dave Stewart <david.c.stewart@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181125185003.593893901@linutronix.de
|
