summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-03-12USB: EHCI: ehci-mv: switch the HSIC HCI to HSIC modeLubomir Rintel
Turns out the undocumented and reserved bits of port status/control register of the root port need to be set to use the HCI in HSIC mode. Typically the firmware does this, but that is not always good enough, because the bits get lost if the HSIC clock is disabled (e.g. when ehci-mv is build as a module). This supplements commit 7b104f890ade ("USB: EHCI: ehci-mv: add HSIC support"). Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12usb: typec: ucsi_ccg: workaround for NVIDIA test deviceAjay Gupta
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA test device FTB (Function Test Board) reports altmode list with vdo=0x3 first and then vdo=0x1. The list is: SVID VDO 0xff01 0xc05 0x28de 0x8085 0x955 0x3 0x955 0x1 Current logic to assign mode value is based on order in altmode list. This causes a mismatch of CON and SOP altmodes since NVIDIA GPU connector has order of vdo=0x1 first and then vdo=0x3. Fixing this by changing the order of vdo values reported by NVIDIA test device. the new list will be: SVID VDO 0xff01 0xc05 0x28de 0x8085 0x955 0x1085 0x955 0x3 Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode. NVIDIA test device reports vdo of 0x1 so make sure vdo values always have pin E assignement. Signed-off-by: Ajay Gupta <ajayg@nvidia.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12USB: mon: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311093003.24604-1-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12media: lmedm04: remove redundant assignment to variable gateColin Ian King
The variable gate is being initialized and also checked and re-assigned with values that are never read as it is being re-assigned later in a for-loop with a new value. The assignments are redundant and can be removed. Addresses Coverity ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12media: tda10071: fix unsigned sign extension overflowColin Ian King
The shifting of buf[3] by 24 bits to the left will be promoted to a 32 bit signed int and then sign-extended to an unsigned long. In the unlikely event that the the top bit of buf[3] is set then all then all the upper bits end up as also being set because of the sign-extension and this affect the ev->post_bit_error sum. Fix this by using the temporary u32 variable bit_error to avoid the sign-extension promotion. This also removes the need to do the computation twice. Addresses-Coverity: ("Unintended sign extension") Fixes: 267897a4708f ("[media] tda10071: implement DVBv5 statistics") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12usb: host: xhci-plat: add a shutdownRan Wang
When loading new kernel via kexec, we need to shutdown host controller to avoid any un-expected memory accessing during new kernel boot. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Cc: stable <stable@vger.kernel.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20200306092328.41253-1-ran.wang_1@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12usb: typec: ucsi: displayport: Fix a potential race during registrationHeikki Krogerus
Locking the connector in ucsi_register_displayport() to make sure that nothing can access the displayport alternate mode before the function has finished and the alternate mode is actually ready. Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200311130006.41288-3-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12usb: typec: ucsi: displayport: Fix NULL pointer dereferenceHeikki Krogerus
If the registration of the DisplayPort was not successful, or if the port does not support DisplayPort alt mode in the first place, the function ucsi_displayport_remove_partner() will fail with NULL pointer dereference when it attempts to access the driver data. Adding a check to the function to make sure there really is driver data for the device before modifying it. Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode") Reported-by: Andrea Gagliardi La Gala <andrea.lagala@gmail.com> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365 Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200311130006.41288-2-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12USB: Disable LPM on WD19's Realtek HubKai-Heng Feng
Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the bus when bringing underlying ports from U3 to U0. Disabling LPM on the hub during setting link state is not enough, so let's disable LPM completely for this hub. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12Staging: rtl8188eu: rtw_mlme: Add space around operatorsShreeya Patel
Add space around operators for improving the code readability. Reported by checkpatch.pl git diff -w shows no difference. diff of the .o files before and after the changes shows no difference. Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Link: https://lore.kernel.org/r/20200311131742.31068-1-shreeya.patel23498@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12thunderbolt: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-03-12media: dw2102: probe for demodulator i2c addressBrad Love
This is required to support the Terratec S2 USB Box Revision 4, which reused usb vid:pid, but has a different demodulator (m88ds3103b) at i2c address 0x6a. [fixed checkpatch issues] Signed-off-by: Michael Bunk <micha@freedict.org> Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12media: em28xx: Enable Hauppauge 461e rev2Brad Love
Hauppauge 461e rev2 is a DVB-S/S2 usb device containing: - m88ds3103b demod - ts2022 tuner - A8293 SEC Device is the same as Hauppauge 461e, except it contains updated m88ds3103b demod. Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12media: m88ds3103: Add support for ds3103b demodBrad Love
The ds3103b demodulator identifies as an m88rs600, but requires different clock settings and firmware, along with differences in register settings. Changes were reverse engineered using an instrumented downstream GPLv2 driver to compare i2c traffic and clocking. The mclk functions are from the downstream GPLv2 driver. Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12staging: rtl8723bs: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311092451.23933-4-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: rtl8192e: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311092451.23933-3-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: rtl8188eu: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311092451.23933-2-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: most: core: Use scnprintf() for avoiding potential buffer overflowTakashi Iwai
Since snprintf() returns the would-be-output size instead of the actual output size, the succeeding calls may go beyond the given buffer limit. Fix it by replacing with scnprintf(). Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200311091944.23185-1-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: wilc1000: updated DT binding documentationAjay Singh
Merged the DT binding documentation of SDIO and SPI into a single file. Removed documentation for some of the properties which are not required and handled review comments received in [1] & [2]. [1]. https://lore.kernel.org/linux-wireless/20200303020230.GA15543@bogus [2]. https://lore.kernel.org/linux-wireless/20200303015558.GA6876@bogus Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Link: https://lore.kernel.org/r/20200307085523.7320-4-ajay.kathat@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: wilc1000: modified 'clock-names' and 'compatible' propertyAjay Singh
Modified the 'clock-names' property by removing '_clk' from its name and remove '_spi/sdio' from 'compatible' string. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Link: https://lore.kernel.org/r/20200307085523.7320-3-ajay.kathat@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12staging: wilc1000: use 'interrupts' property instead of 'irq-gpio'Ajay Singh
Make use of 'interrupts' property instead of using gpio for handling the interrupt as suggested in [1]. [1]. https://lore.kernel.org/linux-wireless/20200303015558.GA6876@bogus Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Link: https://lore.kernel.org/r/20200307085523.7320-2-ajay.kathat@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12media: rc: make scancodes 64 bitSean Young
There are many protocols that encode more than 32 bit. We want 64 bit support so that BPF IR decoders can decode more than 32 bit. None of the existing kernel IR decoders/encoders support 64 bit, for now. The MSC_SCAN event can only contain 32 bit scancodes, so we only generate MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit scancode can be read from the lirc chardev. Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-03-12misc: eeprom: at24: fix regulator underflowMichael Auchter
The at24 driver attempts to read a byte from the device to validate that it's actually present, and if not, disables the vcc regulator and returns -ENODEV. However, between the read and the error handling path, pm_runtime_idle() is called and invokes the driver's suspend callback, which also disables the vcc regulator. This leads to an underflow of the regulator enable count if the EEPROM is not present. Move the pm_runtime_suspend() call to be after the error handling path to resolve this. Fixes: cd5676db0574 ("misc: eeprom: at24: support pm_runtime control") Signed-off-by: Michael Auchter <michael.auchter@ni.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-03-12net: mvmdio: avoid error message for optional IRQChris Packham
Per the dt-binding the interrupt is optional so use platform_get_irq_optional() instead of platform_get_irq(). Since commit 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()") platform_get_irq() produces an error message orion-mdio f1072004.mdio: IRQ index 0 not found which is perfectly normal if one hasn't specified the optional property in the device tree. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12net: dsa: mv88e6xxx: Add missing mask of ATU occupancy registerAndrew Lunn
Only the bottom 12 bits contain the ATU bin occupancy statistics. The upper bits need masking off. Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11net: memcg: fix lockdep splat in inet_csk_accept()Eric Dumazet
Locking newsk while still holding the listener lock triggered a lockdep splat [1] We can simply move the memcg code after we release the listener lock, as this can also help if multiple threads are sharing a common listener. Also fix a typo while reading socket sk_rmem_alloc. [1] WARNING: possible recursive locking detected 5.6.0-rc3-syzkaller #0 Not tainted -------------------------------------------- syz-executor598/9524 is trying to acquire lock: ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492 but task is already holding lock: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(sk_lock-AF_INET6); lock(sk_lock-AF_INET6); *** DEADLOCK *** May be due to missing lock nesting notation 1 lock held by syz-executor598/9524: #0: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] #0: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445 stack backtrace: CPU: 0 PID: 9524 Comm: syz-executor598 Not tainted 5.6.0-rc3-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x188/0x20d lib/dump_stack.c:118 print_deadlock_bug kernel/locking/lockdep.c:2370 [inline] check_deadlock kernel/locking/lockdep.c:2411 [inline] validate_chain kernel/locking/lockdep.c:2954 [inline] __lock_acquire.cold+0x114/0x288 kernel/locking/lockdep.c:3954 lock_acquire+0x197/0x420 kernel/locking/lockdep.c:4484 lock_sock_nested+0xc5/0x110 net/core/sock.c:2947 lock_sock include/net/sock.h:1541 [inline] inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492 inet_accept+0xe9/0x7c0 net/ipv4/af_inet.c:734 __sys_accept4_file+0x3ac/0x5b0 net/socket.c:1758 __sys_accept4+0x53/0x90 net/socket.c:1809 __do_sys_accept4 net/socket.c:1821 [inline] __se_sys_accept4 net/socket.c:1818 [inline] __x64_sys_accept4+0x93/0xf0 net/socket.c:1818 do_syscall_64+0xf6/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4445c9 Code: e8 0c 0d 03 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffc35b37608 EFLAGS: 00000246 ORIG_RAX: 0000000000000120 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00000000004445c9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000306777 R09: 0000000000306777 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00000000004053d0 R14: 0000000000000000 R15: 0000000000000000 Fixes: d752a4986532 ("net: memcg: late association of sock to memcg") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11Merge branch 's390-qeth-fixes'David S. Miller
Julian Wiedmann says: ==================== s390/qeth: fixes 2020-03-11 please apply the following patch series for qeth to netdev's net tree. Just one fix to get the RX buffer pool resizing right, with two preparatory cleanups. This is on the larger side given where we are in the -rc cycle, but a big chunk of the delta is just refactoring to make the fix look nice. I intentionally split these off from yesterday's series. No objections if you'd rather punt them to net-next, the series should apply cleanly. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11s390/qeth: implement smarter resizing of the RX buffer poolJulian Wiedmann
The RX buffer pool is allocated in qeth_alloc_qdio_queues(). A subsequent pool resizing is then handled in a very simple way: first free the current pool, then allocate a new pool of the requested size. There's two ways where this can go wrong: 1. if the resize action happens _before_ the initial pool was allocated, then a subsequent initialization will call qeth_alloc_qdio_queues() and fill the pool with a second(!) set of pages. We consume twice the planned amount of memory. This is easy to fix - just skip the resizing if the queues haven't been allocated yet. 2. if the initial pool was created by qeth_alloc_qdio_queues() but a subsequent resizing fails, then the device has no(!) RX buffer pool. The next initialization will _not_ call qeth_alloc_qdio_queues(), and attempting to back the RX buffers with pages in qeth_init_qdio_queues() will fail. Not very difficult to fix either - instead of re-allocating the whole pool, just allocate/free as many entries to match the desired size. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11s390/qeth: refactor buffer pool codeJulian Wiedmann
In preparation for a subsequent fix, split out helpers to allocate/free individual pool entries. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11s390/qeth: use page pointers to manage RX buffer poolJulian Wiedmann
The RX buffer elements are always backed with full pages, reflect this in the pointer type. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol numberPaolo Lungaroni
The Internet Assigned Numbers Authority (IANA) has recently assigned a protocol number value of 143 for Ethernet [1]. Before this assignment, encapsulation mechanisms such as Segment Routing used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated payload is an Ethernet frame. In this patch, we add the definition of the Ethernet protocol number to the kernel headers and update the SRv6 L2 tunnels to use it. [1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it> Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it> Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11net: dsa: Don't instantiate phylink for CPU/DSA ports unless neededAndrew Lunn
By default, DSA drivers should configure CPU and DSA ports to their maximum speed. In many configurations this is sufficient to make the link work. In some cases it is necessary to configure the link to run slower, e.g. because of limitations of the SoC it is connected to. Or back to back PHYs are used and the PHY needs to be driven in order to establish link. In this case, phylink is used. Only instantiate phylink if it is required. If there is no PHY, or no fixed link properties, phylink can upset a link which works in the default configuration. Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11net/packet: tpacket_rcv: do not increment ring index on dropWillem de Bruijn
In one error case, tpacket_rcv drops packets after incrementing the ring producer index. If this happens, it does not update tp_status to TP_STATUS_USER and thus the reader is stalled for an iteration of the ring, causing out of order arrival. The only such error path is when virtio_net_hdr_from_skb fails due to encountering an unknown GSO type. Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11sxgbe: Fix off by one in samsung driver strncpy size argDominik Czarnota
This patch fixes an off-by-one error in strncpy size argument in drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in: strncmp(opt, "eee_timer:", 6) the passed string literal: "eee_timer:" has 10 bytes (without the NULL byte) and the passed size argument is 6. As a result, the logic will also accept other, malformed strings, e.g. "eee_tiXXX:". This bug doesn't seem to have any security impact since its present in module's cmdline parsing code. Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11net: caif: Add lockdep expression to RCU traversal primitiveAmol Grover
caifdevs->list is traversed using list_for_each_entry_rcu() outside an RCU read-side critical section but under the protection of rtnl_mutex. Hence, add the corresponding lockdep expression to silence the following false-positive warning: [ 10.868467] ============================= [ 10.869082] WARNING: suspicious RCU usage [ 10.869817] 5.6.0-rc1-00177-g06ec0a154aae4 #1 Not tainted [ 10.870804] ----------------------------- [ 10.871557] net/caif/caif_dev.c:115 RCU-list traversed in non-reader section!! Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Amol Grover <frextrite@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11MAINTAINERS: remove Sathya Perla as Emulex NIC maintainerJakub Kicinski
Remove Sathya Perla, sathya.perla@broadcom.com is bouncing. The driver has 3 more maintainers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11net: fec: validate the new settings in fec_enet_set_coalesce()Jakub Kicinski
fec_enet_set_coalesce() validates the previously set params and if they are within range proceeds to apply the new ones. The new ones, however, are not validated. This seems backwards, probably a copy-paste error? Compile tested only. Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-11ipmi_si: Avoid spurious errors for optional IRQsTakashi Iwai
Although the IRQ assignment in ipmi_si driver is optional, platform_get_irq() spews error messages unnecessarily: ipmi_si dmi-ipmi-si.0: IRQ index 0 not found Fix this by switching to platform_get_irq_optional(). Cc: stable@vger.kernel.org # 5.4.x Cc: John Donnelly <john.p.donnelly@oracle.com> Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()") Reported-and-tested-by: Patrick Vo <patrick.vo@hpe.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Message-Id: <20200205093146.1352-1-tiwai@suse.de> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2020-03-12Merge tag 'exynos-drm-fixes-for-v5.6-rc5-v2' of ↵Dave Airlie
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes Fix IOMMU initialization failure when Exynos DRM driver is rebound, and also fix memory leak to iommu mapping object, which was detected by kmemleak detector. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Inki Dae <inki.dae@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1583887109-4148-1-git-send-email-inki.dae@samsung.com
2020-03-12int128: fix __uint128_t compiler test in KconfigMasahiro Yamada
The support for __uint128_t is dependent on the target bit size. GCC that defaults to the 32-bit can still build the 64-bit kernel with -m64 flag passed. However, $(cc-option,-D__SIZEOF_INT128__=0) is evaluated against the default machine bit, which may not match to the kernel it is building. Theoretically, this could be evaluated separately for 64BIT/32BIT. config CC_HAS_INT128 bool default !$(cc-option,$(m64-flag) -D__SIZEOF_INT128__=0) if 64BIT default !$(cc-option,$(m32-flag) -D__SIZEOF_INT128__=0) I simplified it more because the 32-bit compiler is unlikely to support __uint128_t. Fixes: c12d3362a74b ("int128: move __uint128_t compiler test to Kconfig") Reported-by: George Spelvin <lkml@sdf.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: George Spelvin <lkml@sdf.org>
2020-03-12kconfig: introduce m32-flag and m64-flagMasahiro Yamada
When a compiler supports multiple architectures, some compiler features can be dependent on the target architecture. This is typical for Clang, which supports multiple LLVM backends. Even for GCC, we need to take care of biarch compiler cases. It is not a problem when we evaluate cc-option in Makefiles because cc-option is tested against the flag in question + $(KBUILD_CFLAGS). The cc-option in Kconfig, on the other hand, does not accumulate tested flags. Due to this simplification, it could potentially test cc-option against a different target. At first, Kconfig always evaluated cc-option against the host architecture. Since commit e8de12fb7cde ("kbuild: Check for unknown options with cc-option usage in Kconfig and clang"), in case of cross-compiling with Clang, the target triple is correctly passed to Kconfig. The case with biarch GCC (and native build with Clang) is still not handled properly. We need to pass some flags to specify the target machine bit. Due to the design, all the macros in Kconfig are expanded in the parse stage, where we do not know the target bit size yet. For example, arch/x86/Kconfig allows a user to toggle CONFIG_64BIT. If a compiler flag -foo depends on the machine bit, it must be tested twice, one with -m32 and the other with -m64. However, -m32/-m64 are not always recognized. So, this commits adds m64-flag and m32-flag macros. They expand to -m32, -m64, respectively if supported. Or, they expand to an empty string if unsupported. The typical usage is like this: config FOO bool default $(cc-option,$(m64-flag) -foo) if 64BIT default $(cc-option,$(m32-flag) -foo) This is clumsy, but there is no elegant way to handle this in the current static macro expansion. There was discussion for static functions vs dynamic functions. The consensus was to go as far as possible with the static functions. (https://lkml.org/lkml/2018/3/2/22) Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: George Spelvin <lkml@sdf.org> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
2020-03-12kbuild: Fix inconsistent commentSZ Lin (林上智)
The commit 2042b5486bd3 ("kbuild: unset variables in top Makefile instead of setting 0") renamed the variable from "config-targets" to "config-build", the comment should be consistent accordingly. Signed-off-by: Kaiden PK Yu (余泊鎧) <KaidenPK.Yu@moxa.com> Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-03-11x86/tsc_msr: Make MSR derived TSC frequency more accurateHans de Goede
The "Intel 64 and IA-32 Architectures Software Developer’s Manual Volume 4: Model-Specific Registers" has the following table for the values from freq_desc_byt: 000B: 083.3 MHz 001B: 100.0 MHz 010B: 133.3 MHz 011B: 116.7 MHz 100B: 080.0 MHz Notice how for e.g the 83.3 MHz value there are 3 significant digits, which translates to an accuracy of a 1000 ppm, where as a typical crystal oscillator is 20 - 100 ppm, so the accuracy of the frequency format used in the Software Developer’s Manual is not really helpful. As far as we know Bay Trail SoCs use a 25 MHz crystal and Cherry Trail uses a 19.2 MHz crystal, the crystal is the source clock for a root PLL which outputs 1600 and 100 MHz. It is unclear if the root PLL outputs are used directly by the CPU clock PLL or if there is another PLL in between. This does not matter though, we can model the chain of PLLs as a single PLL with a quotient equal to the quotients of all PLLs in the chain multiplied. So we can create a simplified model of the CPU clock setup using a reference clock of 100 MHz plus a quotient which gets us as close to the frequency from the SDM as possible. For the 83.3 MHz example from above this would give 100 MHz * 5 / 6 = 83 and 1/3 MHz, which matches exactly what has been measured on actual hardware. Use a simplified PLL model with a reference clock of 100 MHz for all Bay and Cherry Trail models. This has been tested on the following models: CPU freq before: CPU freq after: Intel N2840 2165.800 MHz 2166.667 MHz Intel Z3736 1332.800 MHz 1333.333 MHz Intel Z3775 1466.300 MHz 1466.667 MHz Intel Z8350 1440.000 MHz 1440.000 MHz Intel Z8750 1600.000 MHz 1600.000 MHz This fixes the time drifting by about 1 second per hour (20 - 30 seconds per day) on (some) devices which rely on the tsc_msr.c code to determine the TSC frequency. Reported-by: Vipul Kumar <vipulk0511@gmail.com> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200223140610.59612-3-hdegoede@redhat.com
2020-03-11x86/tsc_msr: Fix MSR_FSB_FREQ mask for Cherry Trail devicesHans de Goede
According to the "Intel 64 and IA-32 Architectures Software Developer's Manual Volume 4: Model-Specific Registers" on Cherry Trail (Airmont) devices the 4 lowest bits of the MSR_FSB_FREQ mask indicate the bus freq unlike on e.g. Bay Trail where only the lowest 3 bits are used. This is also the reason why MAX_NUM_FREQS is defined as 9, since Cherry Trail SoCs have 9 possible frequencies, so the lo value from the MSR needs to be masked with 0x0f, not with 0x07 otherwise the 9th frequency will get interpreted as the 1st. Bump MAX_NUM_FREQS to 16 to avoid any possibility of addressing the array out of bounds and makes the mask part of the cpufreq struct so it can be set it per model. While at it also log an error when the index points to an uninitialized part of the freqs lookup-table. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200223140610.59612-2-hdegoede@redhat.com
2020-03-11x86/tsc_msr: Use named struct initializersHans de Goede
Use named struct initializers for the freq_desc struct-s initialization and change the "u8 msr_plat" to a "bool use_msr_plat" to make its meaning more clear instead of relying on a comment to explain it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200223140610.59612-1-hdegoede@redhat.com
2020-03-11x86: Select HARDIRQS_SW_RESEND on x86Hans de Goede
Modern x86 laptops are starting to use GPIO pins as interrupts more and more, e.g. touchpads and touchscreens have almost all moved away from PS/2 and USB to using I2C with a GPIO pin as interrupt. Modern x86 laptops also have almost all moved to using s2idle instead of using the system S3 ACPI power state to suspend. The Intel and AMD pinctrl drivers do not define irq_retrigger handlers for the irqchips they register, this is causing edge triggered interrupts which happen while suspended using s2idle to get lost. One specific example of this is the lid switch on some devices, lid switches used to be handled by the embedded-controller, but now the lid open/closed sensor is sometimes directly connected to a GPIO pin. On most devices the ACPI code for this looks like this: Method (_E00, ...) { Notify (LID0, 0x80) // Status Change } Where _E00 is an ACPI event handler for changes on both edges of the GPIO connected to the lid sensor, this event handler is then combined with an _LID method which directly reads the pin. When the device is resumed by opening the lid, the GPIO interrupt will wake the system, but because the pinctrl irqchip doesn't have an irq_retrigger handler, the Notify will not happen. This is not a problem in the case the _LID method directly reads the GPIO, because the drivers/acpi/button.c code will call _LID on resume anyways. But some devices have an event handler for the GPIO connected to the lid sensor which looks like this: Method (_E00, ...) { if (LID_GPIO == One) LIDS = One else LIDS = Zero Notify (LID0, 0x80) // Status Change } And the _LID method returns the cached LIDS value, since on open we do not re-run the edge-interrupt handler when we re-enable IRQS on resume (because of the missing irq_retrigger handler), _LID now will keep reporting closed, as LIDS was never changed to reflect the open status, this causes userspace to re-resume the laptop again shortly after opening the lid. The Intel GPIO controllers do not allow implementing irq_retrigger without emulating it in software, at which point we are better of just using the generic HARDIRQS_SW_RESEND mechanism rather then re-implementing software emulation for this separately in aprox. 14 different pinctrl drivers. Select HARDIRQS_SW_RESEND to solve the problem of edge-triggered GPIO interrupts not being re-triggered on resume when they were triggered during suspend (s2idle) and/or when they were the cause of the wakeup. This requires 008f1d60fe25 ("x86/apic/vector: Force interupt handler invocation to irq context") c16816acd086 ("genirq: Add protection against unsafe usage of generic_handle_irq()") to protect the APIC based interrupts from being wreckaged by a software resend. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20200123210242.53367-1-hdegoede@redhat.com
2020-03-11drm/i915: Defer semaphore priority bumping to a workqueueChris Wilson
Since the semaphore fence may be signaled from inside an interrupt handler from inside a request holding its request->lock, we cannot then enter into the engine->active.lock for processing the semaphore priority bump as we may traverse our call tree and end up on another held request. CPU 0: [ 2243.218864] _raw_spin_lock_irqsave+0x9a/0xb0 [ 2243.218867] i915_schedule_bump_priority+0x49/0x80 [i915] [ 2243.218869] semaphore_notify+0x6d/0x98 [i915] [ 2243.218871] __i915_sw_fence_complete+0x61/0x420 [i915] [ 2243.218874] ? kmem_cache_free+0x211/0x290 [ 2243.218876] i915_sw_fence_complete+0x58/0x80 [i915] [ 2243.218879] dma_i915_sw_fence_wake+0x3e/0x80 [i915] [ 2243.218881] signal_irq_work+0x571/0x690 [i915] [ 2243.218883] irq_work_run_list+0xd7/0x120 [ 2243.218885] irq_work_run+0x1d/0x50 [ 2243.218887] smp_irq_work_interrupt+0x21/0x30 [ 2243.218889] irq_work_interrupt+0xf/0x20 CPU 1: [ 2242.173107] _raw_spin_lock+0x8f/0xa0 [ 2242.173110] __i915_request_submit+0x64/0x4a0 [i915] [ 2242.173112] __execlists_submission_tasklet+0x8ee/0x2120 [i915] [ 2242.173114] ? i915_sched_lookup_priolist+0x1e3/0x2b0 [i915] [ 2242.173117] execlists_submit_request+0x2e8/0x2f0 [i915] [ 2242.173119] submit_notify+0x8f/0xc0 [i915] [ 2242.173121] __i915_sw_fence_complete+0x61/0x420 [i915] [ 2242.173124] ? _raw_spin_unlock_irqrestore+0x39/0x40 [ 2242.173137] i915_sw_fence_complete+0x58/0x80 [i915] [ 2242.173140] i915_sw_fence_commit+0x16/0x20 [i915] Closes: https://gitlab.freedesktop.org/drm/intel/issues/1318 Fixes: b7404c7ecb38 ("drm/i915: Bump ready tasks ahead of busywaits") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v5.2+ Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200310101720.9944-1-chris@chris-wilson.co.uk (cherry picked from commit 209df10bb4536c81c2540df96c02cd079435357f) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2020-03-11drm/i915/gt: Close race between cacheline_retire and freeChris Wilson
If the cacheline may still be busy, atomically mark it for future release, and only if we can determine that it will never be used again, immediately free it. Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392 Fixes: ebece7539242 ("drm/i915: Keep timeline HWSP allocated until idle across the system") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.2+ Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk (cherry picked from commit 2d4bd971f5baa51418625f379a69f5d58b5a0450) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2020-03-11drm/i915/execlists: Enable timeslice on partial virtual engine dequeueChris Wilson
If we stop filling the ELSP due to an incompatible virtual engine request, check if we should enable the timeslice on behalf of the queue. This fixes the case where we are inspecting the last->next element when we know that the last element is the last request in the execution queue, and so decided we did not need to enable timeslicing despite the intent to do so! Fixes: 8ee36e048c98 ("drm/i915/execlists: Minimalistic timeslicing") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk (cherry picked from commit 3df2deed411e0f1b7312baf0139aab8bba4c0410) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2020-03-11drm/i915: be more solid in checking the alignmentMatthew Auld
The alignment is u64, and yet is_power_of_2() assumes unsigned long, which might give different results between 32b and 64b kernel. Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com Cc: stable@vger.kernel.org (cherry picked from commit 2920516b2f719546f55079bc39a7fe409d9e80ab) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
generated by cgit (git 2.34.1) at 2025-10-02 17:13:50 +0000