| Age | Commit message (Collapse) | Author |
|---|
|
For whatever reason we never actually update pagi_count (the in-core
perag inode count) when we allocate or free inode chunks. Online scrub
is going to use it, so we need to fix the accounting.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
|
|
This driver provides an in-kernel and a user API for accessing
the command FIFO of the SBE (Self Boot Engine) of the POWER9
processor, via the FSI bus.
It provides an in-kernel interface to submit command and receive
responses, along with a helper to locate and analyse the response
status block. It's a simple synchronous submit() type API.
The user interface uses the write/read interface that an earlier
version of this driver already provided, however it has some
specific limitations in order to keep the driver simple and
avoid using up a lot of kernel memory:
- The user should perform a single write() with the command and
a single read() to get the response (with a buffer big enough
to hold the entire response).
- On a write() the command is simply "stored" into a kernel buffer,
it is submitted as one operation on the subsequent read(). This
allows to have the code write directly from the FIFO into the user
buffer and avoid hogging the SBE between the write() and read()
syscall as it's critical that the SBE be freed asap to respond
to the host. An extra write() will simply replace the previously
written command.
- A write of a single 4 bytes containing the value 0x52534554
in big endian will trigger a reset request. No read is necessary,
the write() call will return when the reset has been acknowledged
or times out.
- The command is limited to 4K bytes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
---
|
|
The PIB reset causes problems for the running P9 chip. The reset
shouldn't be performed by this driver.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
We currently use a spinlock (bit_lock) around operations that clock bits
out of the FSI bus, and a mutex to protect against simultaneous access
to the master.
This means that bit_lock isn't needed for mutual exlusion, only to
prevent timing issues when clocking bits out.
To reflect this, this change converts bit_lock to just the
local_irq_save/restore operation.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
Remove calls to the empty and useless fsi_master_gpio_error()
function, and report CRC errors as "FSI_ERR_NO_SLAVE" when
reading an all 1's response.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
The FSI protocol defines two modes of recovery from CRC errors,
this implements both:
- If the device returns an ECRC (it detected a CRC error in the
command), then we simply issue the command again.
- If the master detects a CRC error in the response, we send
an E_POLL command which requests a resend of the response
without actually re-executing the command (which could otherwise
have unwanted side effects such as dequeuing a FIFO twice).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
---
Note: This was actually tested by removing some of my fixes, thus
causing us to hit occasional CRC errors during high LPC activity.
|
|
FSI CFAMs support shorter commands that use a relative (or same) address
as the last. This change introduces a last_addr to the master state, and
uses it for subsequent reads/writes, and performs relative addressing
when a subsequent read/write is in range.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
For implementing relative addressing mode, we'll need to build a command
that is coherent with CFAM state. To do that, include the
build_command_* functions in the locked section of read/write/term.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
Most SoC GPIO implementations, including the Aspeed one, have
synchronizers on the GPIO inputs. This means that the value
read from a GPIO is a couple of clocks old, from whatever clock
source feeds those synchronizers.
In practice, this means that in no-delay mode, we are using a
value that can potentially be a bit too old and too close to
the clock edge establishing the data on the other side of the link.
The voltage converters we use on some systems make this worse
and sensitive to things like voltage fluctuations etc... This is,
we believe, the cause of occasional CRC errors encountered during
heavy activity on the LPC bus.
This is fixed by introducing a dummy GPIO read before the actual
data read. It slows down SBEFIFO by about 15% (less than any delay
primitive) and the end result is so far solid.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
FSI_GPIO_DPOLL_CLOCKS is the number of clocks before sending
a DPOLL command after receiving a BUSY status. It should be
at least tSendDelay (16 clocks).
According to comments in the code, it needs to also be at least
21 clocks due to HW issues.
It's currently 100 clocks which impacts performances negatively
in some cases. Reduces it in half to 50 clocks which seems to
still be solid.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
FSI_GPIO_PRIME_SLAVE_CLOCKS is the number of clocks if the
"idle" phase between the end of a response and the beginning
of the next one. It corresponds to tSendDelay in the FSI
specification.
The default value in the slave is 16 clocks. 100 is way overkill
and significantly reduces the driver performance.
This changes it to 20 (which gives the HW a bit of margin still
just in case).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
This adds support for an optional device-tree property that
makes the driver skip all the delays around clocking the
GPIOs and set it in the device-tree of common POWER9 based
OpenPower platforms.
This useful on chips like the AST2500 where the GPIO block is
running at a fairly low clock frequency (25Mhz typically). In
this case, the delays are unnecessary and due to the low
precision of the timers, actually quite harmful in terms of
performance.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
We currently sample the input data right after we toggle the
clock low, then high. The slave establishes the data on the
rising edge, so this is not ideal. We should sample it on
the low phase instead.
This currently works because we have an extra delay, but subsequent
patches will remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
Reduce time spent with interrupts disabled by limiting the critical
sections to bitbanging FSI symbols. We only need to ensure exclusive use
of the bus for an entire transfer, not that the transfer be performed in
atomic context.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
An observation from trace output of the existing FSI tracepoints was
that the remote device was sometimes reporting as busy. Add a new
tracepoint reporting the busy count in order to get a better grip on how
often this is the case.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>
|
|
This is not necessary. skb_gro_receive() will never change what
'head' points to.
In it's original implementation (see commit 71d93b39e52e ("net: Add
skb_gro_receive")), it did:
====================
+ *head = nskb;
+ nskb->next = p->next;
+ p->next = NULL;
====================
This sequence was removed in commit 58025e46ea2d ("net: gro: remove
obsolete code from skb_gro_receive()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
|
|
The existing comments for transport features are outdated.
So update them to address the latest changes in the spec.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
There is a new feature bit allocated in virtio spec to
support SR-IOV (Single Root I/O Virtualization):
https://github.com/oasis-tcs/virtio-spec/issues/11
This patch enables the support for this feature bit in
virtio driver.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
struct vhost_msg within struct vhost_msg_node is copied to userspace.
Unfortunately it turns out on 64 bit systems vhost_msg has padding after
type which gcc doesn't initialize, leaking 4 uninitialized bytes to
userspace.
This padding also unfortunately means 32 bit users of this interface are
broken on a 64 bit kernel which will need to be fixed separately.
Fixes: CVE-2018-1118
Cc: stable@vger.kernel.org
Reported-by: Kevin Easton <kevin@guarana.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+87cfa083e727a224754b@syzkaller.appspotmail.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for
several SoCs.
- Tegra memory controller reset improvements"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
ARM: tegra: fix compile-testing PCI host driver
soc: rockchip: power-domain: add power domain support for px30
dt-bindings: power: add binding for px30 power domains
dt-bindings: power: add PX30 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3228
dt-bindings: power: add binding for rk3228 power domains
dt-bindings: power: add RK3228 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3128
dt-bindings: power: add binding for rk3128 power domains
dt-bindings: power: add RK3128 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3036
dt-bindings: power: add binding for rk3036 power domains
dt-bindings: power: add RK3036 SoCs header for power-domain
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
soc: mediatek: remove unneeded semicolon
soc: mediatek: add a fixed wait for SRAM stable
soc: mediatek: introduce a CAPS flag for scp_domain_data
soc: mediatek: reuse regmap_read_poll_timeout helpers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-06-12
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Avoid an allocation warning in AF_XDP by adding __GFP_NOWARN for the
umem setup, from Björn.
2) Silence a warning in bpf fs when an application tries to open(2) a
pinned bpf obj due to missing fops. Add a dummy open fop that continues
to just bail out in such case, from Daniel.
3) Fix a BPF selftest urandom_read build issue where gcc complains that
it gets built twice, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-06-11
This series contains fixes to ixgbe IPsec and MACVLAN.
Alex provides the 5 fixes in this series, starting with fixing an issue
where num_rx_pools was not being populated until after the queues and
interrupts were reinitialized when enabling MACVLAN interfaces. Updated
to use CONFIG_XFRM_OFFLOAD instead of CONFIG_XFRM, since the code
requires CONFIG_XFRM_OFFLOAD to be enabled. Moved the IPsec
initialization function to be more consistent with the placement of
similar initialization functions and before the call to reset the
hardware, which will clean up any link issues that may have been
introduced. Fixed the boolean logic that was testing for transmit OR
receive ready bits, when it should have been testing for transmit AND
receive ready bits. Fixed the bit definitions for SECTXSTAT and SECRXSTAT
registers and ensure that if IPsec is disabled on the part, do not
enable it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merging in defconfig updates. It's useful to keep them separate during
development but little point in merging them upstream on their own.
* next/defconfig: (40 commits)
arm64: defconfig: Enable PCIe on msm8996 and db820c
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
arm64: defconfig: enable the Armada thermal driver
ARM: multi_v7_defconfig: Enable RENESAS_WDT
ARM: shmobile: defconfig: Enable RENESAS_WDT_GEN
arm64: defconfig: enable R8A77990 SoC
ARM: multi_v7_defconfig: Add STM32F7 I2C & STM32 USBPHYC support
arm64: defconfig: Increase CMA size for VC4
arm64: defconfig: enable rockchip efuse
ARM: imx_v6_v7_defconfig: Select CONFIG_GPIO_MAX732X by default
ARM: imx_v6_v7_defconfig: enable imx6sll by default
arm64: defconfig: Enable CONFIG_SND_AUDIO_GRAPH_CARD
arm64: defconfig: makes SND_SIMPLE_CARD to module
ARM: multi_v7_defconfig: enable the Meson PWM controller
arm: multi_v7_defconfig: enable the Amlogic Meson I2C driver
arm64: defconfig: enable CONFIG_SPI_ARMADA_3700
arm64: defconfig: Enable CONFIG_PINCTRL_MT7622 by default
arm64: defconfig: Enable bluetooth USB support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Valdis reported a BUG in ipv6_add_addr:
[ 1820.832682] BUG: unable to handle kernel NULL pointer dereference at 0000000000000209
[ 1820.832728] RIP: 0010:ipv6_add_addr+0x280/0xd10
[ 1820.832732] Code: 49 8b 1f 0f 84 6a 0a 00 00 48 85 db 0f 84 4e 0a 00 00 48 8b 03 48 8b 53 08 49 89 45 00 49 8b 47 10
49 89 55 08 48 85 c0 74 15 <48> 8b 50 08 48 8b 00 49 89 95 b8 01 00 00 49 89 85 b0 01 00 00 4c
[ 1820.832847] RSP: 0018:ffffaa07c2fd7880 EFLAGS: 00010202
[ 1820.832853] RAX: 0000000000000201 RBX: ffffaa07c2fd79b0 RCX: 0000000000000000
[ 1820.832858] RDX: a4cfbfba2cbfa64c RSI: 0000000000000000 RDI: ffffffff8a8e9fa0
[ 1820.832862] RBP: ffffaa07c2fd7920 R08: 000000000000017a R09: ffffffff8a555300
[ 1820.832866] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888d18e71c00
[ 1820.832871] R13: ffff888d0a9b1200 R14: 0000000000000000 R15: ffffaa07c2fd7980
[ 1820.832876] FS: 00007faa51bdb800(0000) GS:ffff888d1d400000(0000) knlGS:0000000000000000
[ 1820.832880] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1820.832885] CR2: 0000000000000209 CR3: 000000021e8f8001 CR4: 00000000001606e0
[ 1820.832888] Call Trace:
[ 1820.832898] ? __local_bh_enable_ip+0x119/0x260
[ 1820.832904] ? ipv6_create_tempaddr+0x259/0x5a0
[ 1820.832912] ? __local_bh_enable_ip+0x139/0x260
[ 1820.832921] ipv6_create_tempaddr+0x2da/0x5a0
[ 1820.832926] ? ipv6_create_tempaddr+0x2da/0x5a0
[ 1820.832941] manage_tempaddrs+0x1a5/0x240
[ 1820.832951] inet6_addr_del+0x20b/0x3b0
[ 1820.832959] ? nla_parse+0xce/0x1e0
[ 1820.832968] inet6_rtm_deladdr+0xd9/0x210
[ 1820.832981] rtnetlink_rcv_msg+0x1d4/0x5f0
Looking at the code I found 1 element (peer_pfx) of the newly introduced
ifa6_config struct that is not initialized. Use a memset rather than hard
coding an init for each struct element.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Fixes: e6464b8c63619 ("net/ipv6: Convert ipv6_add_addr to struct ifa6_config")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While hacking on kTLS, I ran into the following panic from an
unprivileged netserver / netperf TCP session:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 800000037f378067 P4D 800000037f378067 PUD 3c0e61067 PMD 0
Oops: 0010 [#1] SMP KASAN PTI
CPU: 1 PID: 2289 Comm: netserver Not tainted 4.17.0+ #139
Hardware name: LENOVO 20FBCTO1WW/20FBCTO1WW, BIOS N1FET47W (1.21 ) 11/28/2016
RIP: 0010: (null)
Code: Bad RIP value.
RSP: 0018:ffff88036abcf740 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88036f5f6800 RCX: 1ffff1006debed26
RDX: ffff88036abcf920 RSI: ffff8803cb1a4f00 RDI: ffff8803c258c280
RBP: ffff8803c258c280 R08: ffff8803c258c280 R09: ffffed006f559d48
R10: ffff88037aacea43 R11: ffffed006f559d49 R12: ffff8803c258c280
R13: ffff8803cb1a4f20 R14: 00000000000000db R15: ffffffffc168a350
FS: 00007f7e631f4700(0000) GS:ffff8803d1c80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 00000003ccf64005 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? tls_sw_poll+0xa4/0x160 [tls]
? sock_poll+0x20a/0x680
? do_select+0x77b/0x11a0
? poll_schedule_timeout.constprop.12+0x130/0x130
? pick_link+0xb00/0xb00
? read_word_at_a_time+0x13/0x20
? vfs_poll+0x270/0x270
? deref_stack_reg+0xad/0xe0
? __read_once_size_nocheck.constprop.6+0x10/0x10
[...]
Debugging further, it turns out that calling into ctx->sk_poll() is
invalid since sk_poll itself is NULL which was saved from the original
TCP socket in order for tls_sw_poll() to invoke it.
Looks like the recent conversion from poll to poll_mask callback started
in 152524231023 ("net: add support for ->poll_mask in proto_ops") missed
to eventually convert kTLS, too: TCP's ->poll was converted over to the
->poll_mask in commit 2c7d3dacebd4 ("net/tcp: convert to ->poll_mask")
and therefore kTLS wrongly saved the ->poll old one which is now NULL.
Convert kTLS over to use ->poll_mask instead. Also instead of POLLIN |
POLLRDNORM use the proper EPOLLIN | EPOLLRDNORM bits as the case in
tcp_poll_mask() as well that is mangled here.
Fixes: 2c7d3dacebd4 ("net/tcp: convert to ->poll_mask")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Watson <davejwatson@fb.com>
Tested-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller reported a warning from xdp_umem_pin_pages():
WARNING: CPU: 1 PID: 4537 at mm/slab_common.c:996 kmalloc_slab+0x56/0x70 mm/slab_common.c:996
...
__do_kmalloc mm/slab.c:3713 [inline]
__kmalloc+0x25/0x760 mm/slab.c:3727
kmalloc_array include/linux/slab.h:634 [inline]
kcalloc include/linux/slab.h:645 [inline]
xdp_umem_pin_pages net/xdp/xdp_umem.c:205 [inline]
xdp_umem_reg net/xdp/xdp_umem.c:318 [inline]
xdp_umem_create+0x5c9/0x10f0 net/xdp/xdp_umem.c:349
xsk_setsockopt+0x443/0x550 net/xdp/xsk.c:531
__sys_setsockopt+0x1bd/0x390 net/socket.c:1935
__do_sys_setsockopt net/socket.c:1946 [inline]
__se_sys_setsockopt net/socket.c:1943 [inline]
__x64_sys_setsockopt+0xbe/0x150 net/socket.c:1943
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x49/0xbe
This is a warning about attempting to allocate more than
KMALLOC_MAX_SIZE memory. The request originates from userspace, and if
the request is too big, the kernel is free to deny its allocation. In
this patch, the failed allocation attempt is silenced with
__GFP_NOWARN.
Fixes: c0c77d8fb787 ("xsk: add user memory registration support sockopt")
Reported-by: syzbot+4abadc5d69117b346506@syzkaller.appspotmail.com
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Reject non-null terminated helper names from xt_CT, from Gao Feng.
2) Fix KASAN splat due to out-of-bound access from commit phase, from
Alexey Kodanev.
3) Missing conntrack hook registration on IPVS FTP helper, from Julian
Anastasov.
4) Incorrect skbuff allocation size in bridge nft_reject, from Taehee Yoo.
5) Fix inverted check on packet xmit to non-local addresses, also from
Julian.
6) Fix ebtables alignment compat problems, from Alin Nastac.
7) Hook mask checks are not correct in xt_set, from Serhey Popovych.
8) Fix timeout listing of element in ipsets, from Jozsef.
9) Cap maximum timeout value in ipset, also from Jozsef.
10) Don't allow family option for hash:mac sets, from Florent Fourcot.
11) Restrict ebtables to work with NFPROTO_BRIDGE targets only, this
Florian.
12) Another bug reported by KASAN in the rbtree set backend, from
Taehee Yoo.
13) Missing __IPS_MAX_BIT update doesn't include IPS_OFFLOAD_BIT.
From Gao Feng.
14) Missing initialization of match/target in ebtables, from Florian
Westphal.
15) Remove useless nft_dup.h file in include path, from C. Labbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When pskb_trim_rcsum fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pskb_trim_rcsum.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPVS setups with local client and remote tunnel server need
to create exception for the local virtual IP. What we do is to
change PMTU from 64KB (on "lo") to 1460 in the common case.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Fixes: 7343ff31ebf0 ("ipv6: Don't create clones of host routes.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- simplify getting .drvdata
renesas_wdt:
- add support for the R8A77965 WDT and R-Car Gen2
- remove R-Car M2-W ES2.x from blacklist
sp805:
- add restart handler
hpwdt:
- claim NMIs generated by iLO5
mena21_wdt:
- drop unnecessary mutex lock
da9062 & da9063:
- fixes and general cleanups"
* tag 'linux-watchdog-4.18-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: da9063: remove duplicated timeout_to_sel calls
watchdog: da9063: rename helper function to avoid misunderstandings
watchdog: da9062: remove unused code
watchdog: da9063: Fix timeout handling during probe
watchdog: da9063: Fix updating timeout value
watchdog: da9063: Fix setting/changing timeout
dt-bindings: watchdog: renesas-wdt: Add R-Car Gen2 support
watchdog: mena21_wdt: Drop unnecessary mutex lock
watchdog: renesas-wdt: Add support for the R8A77965 WDT
watchdog: hpwdt: Claim NMIs generated by iLO5
watchdog: sp805: add restart handler
watchdog: renesas-wdt: Remove R-Car M2-W ES2.x from blacklist
watchdog: simplify getting .drvdata
|
|
dma_direct_{alloc,free}()"
This reverts commit b468620f2a1dfdcfddfd6fa54367b8bcc1b51248.
It turns out that this broke drm on AMD platforms. Quoting Gabriel C:
"I can confirm reverting b468620f2a1dfdcfddfd6fa54367b8bcc1b51248 fixes
that issue for me.
The GPU is working fine with SME enabled.
Now with working GPU :) I can also confirm performance is back to
normal without doing any other workarounds"
Christan König analyzed it partially:
"As far as I analyzed it we now get an -ENOMEM from dma_alloc_attrs()
in drivers/gpu/drm/ttm/ttm_page_alloc_dma.c when IOMMU is enabled"
and Christoph Hellwig responded:
"I think the prime issue is that dma_direct_alloc respects the dma
mask. Which we don't need if actually using the iommu. This would be
mostly harmless exept for the the SEV bit high in the address that
makes the checks fail.
For now I'd say revert this commit for 4.17/4.18-rc and I'll look into
addressing these issues properly"
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org # v4.17
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ntb_transport_create_queue
ntb_transport_create_queue() is never called in atomic context.
ntb_transport_create_queue() is only called by ntb_netdev_probe(),
which is set as ".probe" in struct ntb_transport_client.
Despite never getting called from atomic context,
ntb_transport_create_queue() calls kzalloc_node() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
ntb_transport_setup_qp_mw
ntb_transport_setup_qp_mw() is never called in atomic context.
ntb_transport_setup_qp_mw() is only called by ntb_transport_link_work(),
which is set as a parameter of INIT_DELAYED_WORK()
in ntb_transport_probe().
Despite never getting called from atomic context,
ntb_transport_setup_qp_mw() calls kzalloc_node() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Change all references to skx to gen3 NTB.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Move the Intel hw gen3 code to its own source file. The ntb_hw_intel.c was
getting too large and makes it hard to maintain with future hardware
changes.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Break out the generation specific definitions to different headers
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Pull rpmsg updates from Bjorn Andersson:
"This migrates rpmsg to use SPDX license headers and fixes a
use-after-free in SMD"
* tag 'rpmsg-v4.18' of git://github.com/andersson/remoteproc:
rpmsg: smd: do not use mananged resources for endpoints and channels
rpmsg: char: Switch to SPDX license identifier
rpmsg: glink: Switch to SPDX license identifier
rpmsg: smd: Switch to SPDX license identifier
rpmsg: virtio_rpmsg_bus: Switch to SPDX license identifier
rpmsg: Switch to SPDX license identifier
rpmsg: qcom_smd: Access APCS through mailbox framework
rpmsg: Add driver_override device attribute for rpmsg_device
|
|
Pull remoteproc updates from Bjorn Andersson:
"This brings a few minor fixes to the Davinci driver, drops a orphan
include file from the StE cleanup done ealier and introduces support
for booting the modem on Qualcomm's SDM845 platform"
* tag 'rproc-v4.18' of git://github.com/andersson/remoteproc:
remoteproc: q6v5: Allow defining GLINK edge for mss remoteproc
remoteproc: q6v5: Add support for mss remoteproc on SDM845
remoteproc: q6v5: Introduce reset assert/deassert helper functions
dt-bindings: remoteproc: Add Q6v5 Modem PIL binding for SDM845
remoteproc: q6v5: Move proxy unvote to handover irq handler
remoteproc: q6v5: Return irq from q6v5_request_irq()
remoteproc/ste: remove abandoned include file
remoteproc/davinci: use octal permissions for module_param()
remoteproc/davinci: prepare and unprepare the clock where needed
remoteproc/davinci: add the missing retval check for clk_enable()
remoteproc: Remove depends on HAS_DMA in case of platform dependency
remoteproc: Prevent incorrect rproc state on xfer mem ownership failure
|
|
Pull hwspinlock updates from Bjorn Andersson:
"In addition to migrating the files to use SPDX license headers this
introduces the ability for clients to operate a hwlock without the
framework taking any additional locks"
* tag 'hwlock-v4.18' of git://github.com/andersson/remoteproc:
hwspinlock/u8500: Switch to SPDX license identifier
hwspinlock: sprd: Switch to SPDX license identifier
hwspinlock/sirf: Switch to SPDX license identifier
hwspinlock: qcom: Switch to SPDX license identifier
hwspinlock/omap: Switch to SPDX license identifier
hwspinlock/core: Switch to SPDX license identifier
hwspinlock: Introduce one new mode for hwspinlock
hwspinlock: Convert to use 'switch' statement
|
|
Al noted that the semantics of the ia64 perfmon mmap() is really wrong,
and can cause serious VM problems. Before we look at whether it needs
to be fixed, let's see if anybody even uses it, and mark it broken. It
may be that we can just remove the code entirely.
Reported-by: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, we've mainly focused on discard, aka unmap, control
along with fstrim for Android-specific usage model. In addition, we've
fixed writepage flow which returned EAGAIN previously resulting in EIO
of fsync(2) due to mapping's error state. In order to avoid old MM bug
[1], we decided not to use __GFP_ZERO for the mapping for node and
meta page caches. As always, we've cleaned up many places for future
fsverity and symbol conflicts.
Enhancements:
- do discard/fstrim in lower priority considering fs utilization
- split large discard commands into smaller ones for better responsiveness
- add more sanity checks to address syzbot reports
- add a mount option, fsync_mode=nobarrier, which can reduce # of cache flushes
- clean up symbol namespace with modified function names
- be strict on block allocation and IO control in corner cases
Bug fixes:
- don't use __GFP_ZERO for mappings
- fix error reports in writepage to avoid fsync() failure
- avoid selinux denial on CAP_RESOURCE on resgid/resuid
- fix some subtle race conditions in GC/atomic writes/shutdown
- fix overflow bugs in sanity_check_raw_super
- fix missing bits on get_flags
Clean-ups:
- prepare the generic flow for future fsverity integration
- fix some broken coding standard"
[1] https://lkml.org/lkml/2018/4/8/661
* tag 'f2fs-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (79 commits)
f2fs: fix to clear FI_VOLATILE_FILE correctly
f2fs: let sync node IO interrupt async one
f2fs: don't change wbc->sync_mode
f2fs: fix to update mtime correctly
fs: f2fs: insert space around that ':' and ', '
fs: f2fs: add missing blank lines after declarations
fs: f2fs: changed variable type of offset "unsigned" to "loff_t"
f2fs: clean up symbol namespace
f2fs: make set_de_type() static
f2fs: make __f2fs_write_data_pages() static
f2fs: fix to avoid accessing cross the boundary
f2fs: fix to let caller retry allocating block address
disable loading f2fs module on PAGE_SIZE > 4KB
f2fs: fix error path of move_data_page
f2fs: don't drop dentry pages after fs shutdown
f2fs: fix to avoid race during access gc_thread pointer
f2fs: clean up with clear_radix_tree_dirty_tag
f2fs: fix to don't trigger writeback during recovery
f2fs: clear discard_wake earlier
f2fs: let discard thread wait a little longer if dev is busy
...
|
|
The SBI exists on all RISC-V systems, so there's no reason not to
compile this driver in.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
This patch set contains a handful of fixes that clean up the sparse
results for the RISC-V port. These patches shouldn't have any
functional difference. The patches:
* Use NULL instead of 0.
* Clean up __user annotations.
* Split __copy_user into two functions, to make the __user annotations
valid.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
|
|
This patch set contains a pair of RISC-V related updates to the
MAINTAINERS file:
* Albert is now back at UC Berkeley.
* I've added myself as a maintainer for anything with "sifive" in the
name.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
With CONFIG_MODVERSIONS=y the R_RISCV_32 relocation is used by the
__kcrctab section.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
