| Age | Commit message (Collapse) | Author |
|---|
|
into drm-next
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
|
|
git://people.freedesktop.org/~thomash/linux into drm-next
Pull request of 15-08-21
The third pull request for 4.3. Contains two fixes for regressions introduced
with previous pull requests.
* tag 'vmwgfx-next-15-08-21' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Remove duplicate ttm_bo_device_release
drm/vmwgfx: Fix a circular locking dependency in the fbdev code
|
|
into drm-next
- DP fixes for radeon and amdgpu
- IH ring fix for tonga and fiji
- Lots of GPU scheduler fixes
- Misc additional fixes
* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux: (42 commits)
drm/amdgpu: fix wait queue handling in the scheduler
drm/amdgpu: remove extra parameters from scheduler callbacks
drm/amdgpu: wake up scheduler only when neccessary
drm/amdgpu: remove entity idle timeout v2
drm/amdgpu: fix postclose order
drm/amdgpu: use IB for copy buffer of eviction
drm/amdgpu: adjust the judgement of removing fence callback
drm/amdgpu: fix no sync_wait in copy_buffer
drm/amdgpu: fix last_vm_update fence is not effetive for sched fence
drm/amdgpu: add priv data to sched
drm/amdgpu: add owner for sched fence
drm/amdgpu: remove entity reference from sched fence
drm/amdgpu: fix and cleanup amd_sched_entity_push_job
drm/amdgpu: remove amdgpu_bo_list_clone
drm/amdgpu: remove the context from amdgpu_job
drm/amdgpu: remove unused parameters to amd_sched_create
drm/amdgpu: remove sched_lock
drm/amdgpu: remove prepare_job callback
drm/amdgpu: cleanup a scheduler function name
drm/amdgpu: reorder scheduler functions
...
|
|
The queuecommand routine has a local dev pointer used for the
dev_* prints. The two prints that currently exist are tucked
under a debug define and thus can be left out. Use the actual
location instead of a local to avoid this warning.
This patch is intended to be applied after the "CXL Flash Error
Recovery and Superpipe" series.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
"port_sel" is a u64 so the shifting should also be a 64 bit shift.
Fixes: c21e0bbfc485 ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The > should be >= or we read one element past the end of the array.
Fixes: c21e0bbfc485 ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Add support for physical LUN segmentation (virtual LUNs) to device
driver supporting the IBM CXL Flash adapter. This patch allows user
space applications to virtually segment a physical LUN into N virtual
LUNs, taking advantage of the translation features provided by this
adapter.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Add superpipe supporting infrastructure to device driver for the IBM CXL
Flash adapter. This patch allows userspace applications to take advantage
of the accelerated I/O features that this adapter provides and bypass the
traditional filesystem stack.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Introduce support for enhanced I/O error handling.
A device state is added to track 3 possible states of the device:
Normal - the device is operating normally and is fully operational
Limbo - the device is in a reset/recovery scenario and its operational
status is paused
Failed/terminating - the device has either failed to be reset/recovered
or is being terminated (removed); it is no longer
operational
All operations are allowed when the device is operating normally. When the
device transitions to limbo state, I/O must be paused. To help accomplish
this, a wait queue is introduced where existing and new threads can wait
until the device is no longer in limbo. When coming out of limbo, threads
need to check the state and error out gracefully when encountering the
failed state. When the device transitions to the failed/terminating state,
normal operations are no longer allowed. Only specially designated
operations related to graceful cleanup are permitted.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
On certain conditions, login failures will just invoke
qla2x00_mark_device_lost() with the intend to do login again;
but if login_retry has been set already, that would fail to set the
relogin needed flag which is required to wakeup the DPC to retry.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Fix for memory leak when command is not found by firmware due to
mismatch in sp reference count.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Aovid crashing the system in the scenario where firmware
just completes the command and it can not find the command
during abort mailbox processing. This scenario can lead to
sp reference counter being zero. Instead of crashing the
system, use WARN_ON to print warning in log file.
Signed-off-by: Hiral Patel <hiral.patel@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Execute qla25xx_manipulate_risc_semaphore() only for
ssdid 0x0175 and 0x0240.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
When we get logged out, mark the port lost and set dpc flag for relogin.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Make sure to indicate to tunnel driver that key.tun_id is set,
otherwise gre won't recognize the metadata.
Fixes: d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
scsi_error: should not get sense for timeout IO in scsi error handler
When an IO timeout occurs, the IO will be aborted in
scsi_abort_command() and SCSI_EH_ABORT_SCHEDULED will be set. Because
of that, the SCSI_EH_CANCEL_CMD will be clear in scsi_eh_scmd_add().
So when scsi error handler starts, it will get sense for this
timeout IO and the scmd of the IO request will be reused. In that
case, the scmd may be double released when racing with io_done(),
which will result in crash.
SO SCSI_EH_ABORT_SCHEDULED should also be checked when getting sense.
The bug maybe reproduced when the link between host and disk is
unstable.
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Long Chun <long.chun@zte.com.cn>
Reviewed-by: Tan Hu <tan.hu@zte.com.cn>
Reviewed-by: Chen Donghai <chen.donghai@zte.com.cn>
Reviewed-by: Cai Qu <cai.qu@zte.com.cn>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Bump pm80xx driver version to 0.1.38.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The request has to be retried incase if the length of the SSP
Response IU is invalid.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
If the link error happens, we don't need to disconnect the phy,
which will remove the drive. Instead acknowledging the controller
and logging the error will be enough.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In pm8001_ccb_task_free(), the dma unmapping is done based on
ccb->n_elem value. This should be initialized to zero in the
task_abort(). Otherwise, pm8001_ccb_task_free() will try for
dma_unmap_sg() which is invalid for task abort and can lead to
kernel crash.
Changes From V1:
None
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Thermal page code has been changed to 7 for the 12G controllers.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In Nexus reset the device state request are not needed.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Updated 12G linkrate to libsas.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Company has policy to use company email address, so update
my email address to company address.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Use logical instead of bitwise AND.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Invoking get_cmd_state for qla2xxx always returns 0. Instead change it
to return the actual fabric state from qla_tgt_cmd. This will help with
debugging.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The driver is calling hpsa_shutdown before calling scsi_remove_host.
hpsa_shutdown is disabling interrupts.
scsi_remove_host can trigger I/O operations, such as
SYNCHRONIZE CACHE when multipath is enabled which hang the system.
Call scsi_remove_host before calling hpsa_shutdown.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
A regression was introduced into the hpsa driver a while back so
non-zero LUNs of multi-LUN devices may no longer be presented via
a SAS based Smart Array. I have not done a bisection to discover
the change that caused it.
The CISS firmware specification (available on sourceforge)
defines an 8 byte lunid that describes devices that the Smart
Array can see/present to the system. The current code in the hpsa
driver attempts to find matches for non-zero LUNs with LUN 0 for
a bus/target by zeroing out byte 4 of the lunid and find a match.
This method is sufficient for SCSI based Smart Arrays because
byte 5 is always 0. For SAS based Smart arrays byte 5 of the
lunid contains the path number for a multipath device and
either one or two bits (the documentation does not define how
many bits are used but it appears it may be one only) that
indicate if the given path number in byte 5 must always be
used to access that device. Byte 5 may not always be zero.
The following are lunids (spaces added for clarity) for a
MSL2024 single drive library connected via a H241 Smart Array:
00 00 00 00 01 00 00 01 (changer)
00 00 00 00 00 80 00 01 (tape)
In the 4th byte (counting from 0) you can see that the tape
is LUN 0 and the changer is LUN 1. The 0x80 set in the 5th byte
for the tape drive means the driver should force access to
path 0 (the library in this case was connected to one path only
anyway).
After the changes we can see the following in the dmesg output:
scsi 0:3:0:0: RAID HP H241 1.18 \
PQ: 0 ANSI: 5
scsi 0:2:0:0: Sequential-Access HP Ultrium 6-SCSI 354W \
PQ: 0 ANSI: 6
scsi 0:2:0:1: Medium Changer HP MSL G3 Series 8.70 \
PQ: 0 ANSI: 5
Showing that the changer is correctly identified as LUN 1 of
bus 2 target 0. Before the change the changer device is not seen.
Suggested-by: shane.seymour <shane.seymour@hp.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
prevent adding volumes that are not available.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
showing that tables have been updated unnecessarily.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
host no, bus, target, lun, scsi_device_type
for hba mode add: box and bay information
report if the path is active/inactive
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
need to add PMC to copyright notice and update the Hewlett-Packard
copyright notification.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Nick Meier reported a regression with HyperV that "
After rebooting the VM, the following messages are logged in syslog
when trying to load the tulip driver:
tulip: Linux Tulip drivers version 1.1.15 (Feb 27, 2007)
tulip: 0000:00:0a.0: PCI INT A: failed to register GSI
tulip: Cannot enable tulip board #0, aborting
tulip: probe of 0000:00:0a.0 failed with error -16
Errors occur in 3.19.0 kernel
Works in 3.17 kernel.
"
According to the ACPI dump file posted by Nick at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
The ACPI MADT table includes an interrupt source overridden entry for
ACPI SCI:
[236h 0566 1] Subtable Type : 02 <Interrupt Source Override>
[237h 0567 1] Length : 0A
[238h 0568 1] Bus : 00
[239h 0569 1] Source : 09
[23Ah 0570 4] Interrupt : 00000009
[23Eh 0574 2] Flags (decoded below) : 000D
Polarity : 1
Trigger Mode : 3
And in DSDT table, we have _PRT method to define PCI interrupts, which
eventually goes to:
Name (PRSA, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSB, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSC, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSD, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
According to the MADT and DSDT tables, IRQ 9 may be used for:
1) ACPI SCI in level, high mode
2) PCI legacy IRQ in level, low mode
So there's a conflict in polarity setting for IRQ 9.
Prior to commit cd68f6bd53cf ("x86, irq, acpi: Get rid of special
handling of GSI for ACPI SCI"), ACPI SCI is handled specially and
there's no check for conflicts between ACPI SCI and PCI legagy IRQ.
And it seems that the HyperV hypervisor doesn't make use of the
polarity configuration in IOAPIC entry, so it just works.
Commit cd68f6bd53cf gets rid of the specially handling of ACPI SCI,
and then the pin attribute checking code discloses the conflicts
between ACPI SCI and PCI legacy IRQ on HyperV virtual machine,
and rejects the request to assign IRQ9 to PCI devices.
So penalize legacy IRQ used by ACPI SCI and mark it unusable if ACPI
SCI attributes conflict with PCI IRQ attributes.
Please refer to following links for more information:
https://bugzilla.kernel.org/show_bug.cgi?id=101301
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
Fixes: cd68f6bd53cf ("x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI")
Reported-and-tested-by: Nick Meier <nmeier@microsoft.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
