summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-09-07ARM: dts: omap3-gta04: add mcbsp (audio subsystem) nodesH. Nikolaus Schaller
GTA04 audio system makes use of all four McBSP ports, so enable and connect them with pinmux. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add devconf0 setup for mcbsp1 clock pinsH. Nikolaus Schaller
McBSP1 needs special "pinctrl" for the clocks. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add mcbsp (audio subsystem) pinmuxH. Nikolaus Schaller
GTA04 audio system makes use of all four McBSP ports, so set up proper pinmux. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add camera pinmuxH. Nikolaus Schaller
ISP needs camera pinmux (which is referenced by the camera node). Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add camera interface parallel portH. Nikolaus Schaller
The GTA04 has an optional OV9655 camera (for which we do not yet have a driver upstream), but the ISP hardware connection description in the device tree is independent of that. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: map antenna detect GPIO to SW_LINEIN_INSERT key eventH. Nikolaus Schaller
GTA04 can detect presence/absence or plug-in of an external GPS antenna through a gpio. The best match for an event code is SW_LINEIN_INSERT. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: make use of input event include file and constantsH. Nikolaus Schaller
we can replace magic numbers by symbolic constants now. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: explicitly describe that mmc1 has no CD/WPH. Nikolaus Schaller
There are neither CD nor WP switches for mmc1. The µSD slot is located under the SIM card under the battery and not accessible during operation. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add warning comment to vaux2 regulatorH. Nikolaus Schaller
vaux2 should remain always on since a higher potential at vio could potentially damage the itg3200 sensor. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add a comment how to reference the tca6507 gpioH. Nikolaus Schaller
Make clear how to use the wifi_reset since it is not obvious. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: keep vpll2 always onH. Nikolaus Schaller
This is needed to make the display and venc work properly. Compare to omap3-beagle.dts. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: update gpmc NAND setupH. Nikolaus Schaller
to better match omap3-beagle.dts (which was the basis of designing the GTA04). Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: make NAND partitions compatible with recent U-BootH. Nikolaus Schaller
Vendor defined U-Boot has changed the partition scheme a while ago: * kernel partition 6MB * file system partition uses the remainder up to end of the NAND * increased size of the environment partition (to get an OneNAND compatible base address) * shrink the U-Boot partition Let's be compatible (e.g. Debian kernel built from upstream). Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add pinmux for bmp085 EOC interruptH. Nikolaus Schaller
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: fix touchscreen tsc2007H. Nikolaus Schaller
we fix penirq polarity, add penirq pinmux and touchscreen properties. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: tvout: enable as display1 aliasH. Nikolaus Schaller
The omap dss susbystem takes the display aliases to find out which displays exist. To enable tv-out we must define an alias. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: add devconf1 setup for correct tvout pinsH. Nikolaus Schaller
The VENC with external OPA362 amplifier needs a special "pinmux" setup in DEVCONF1 (TVOUTBYPASS and TVOUTACEN). Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: fixes for tvout / vencH. Nikolaus Schaller
* fix connector compatibility (composite) * add comment for gpio1 23 * add proper #address-cells * we use only one venc_out channel for composite Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: give spi_lcd node a label so that we can overwrite in ↵H. Nikolaus Schaller
other DTS files needed for device variants based on GTA04 board but with different display panel (driver). Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: fix some whitespace and tab style errorsH. Nikolaus Schaller
tab+space -> tab only for /* GSM audio */ spaces -> tab for dss_dpi_pins Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-07ARM: dts: omap3-gta04: fix typo in backlight pins node nameH. Nikolaus Schaller
mn -> nm for backlight_pins Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-09-06ARM: dts: exynos: Disable pull control for S5M8767 PMICMarek Szyprowski
S5M8767 PMIC interrupt line on Exynos5250-based Arndale board has external pull-up resistors, so disable any pull control for it in in controller node. This fixes support for S5M8767 interrupts and enables operation of wakeup from S5M8767 RTC alarm. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-06ARM: dts: exynos: Remove double SD card detect pin inversionKrzysztof Kozlowski
The SDHCI standard, MMC host controller bindings and MMC core defines card detect pin as active low. Therefore there is no point to invert it twice. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
2018-09-06ARM: dts: exynos: Add missing PMIC interrupts on UniversalC210 boardMarek Szyprowski
PMIC node requires external interrupts for proper operation. Lack of them was probably caused by a limited support for interrupts from more than one parent, which was not possible to define when support for this board was added. Fix this by adding 'interrupt-extended' property and properly define both interrupt lines for PMIC node. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-06ARM: dts: exynos: Disable pull control for MAX8997 interrupts on OrigenMarek Szyprowski
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have external pull-up resistors, so disable any pull control for those lines in respective pin controller node. This fixes support for MAX8997 interrupts and enables operation of wakeup from MAX8997 RTC alarm. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-06ARM: dts: r9a06g032: Use r9a06g032-sysctrl binding definitionsGeert Uytterhoeven
Replace the hardcoded clock indices by R9A06G032_CLK_* symbols. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-05ARM: dts: bcm283x-rpi-lan7515: Enable Ethernet LEDsStefan Wahren
Since the LAN7515 on Raspberry Pi 3B+ doesn't have an EEPROM and the OTP is empty, we need to enable the Ethernet LEDs via Device Tree. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
2018-09-05ARM: dts: rockchip: add rk3188 lcd controller nodesHeiko Stuebner
Add the core display subsystem and vop nodes to rk3188. Vop0 has a fully dedicated set of pins and only vop1 needs to do pinctrl to have display output, so also add the necessary pinctrl entries for it. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by Sandy Huang <hjc@rock-chips.com>
2018-09-05ARM: dts: sun8i: sun8i-r40-bananapi-m2-ultra: enable AHCICorentin Labbe
This patch enable the AHCI controller. Since this controller need two regulator, this patch add them. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-05ARM: dts: sun8i: r40: add sata nodeCorentin Labbe
R40 have a sata controller which is the same as A20. This patch adds a DT node for it. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-04ARM: dts: meson8b: fix the clock controller register sizeMartin Blumenstingl
The clock controller registers are not 0x460 wide because the reset controller starts at CBUS 0x4404. This currently overlaps with the clock controller (which is at CBUS 0x4000). There is no public documentation available on the actual size of the clock controller's register area (also called "HHI"). However, in Amlogic's GPL kernel sources the last "HHI" register is HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size doesn't seem unlikely. Fixes: 4a69fcd3a10803 ("ARM: meson: Add DTS for Odroid-C1 and Tronfy MXQ boards") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-04ARM: dts: meson8: fix the clock controller register sizeMartin Blumenstingl
The clock controller registers are not 0x460 wide because the reset controller starts at CBUS 0x4404. This currently overlaps with the clock controller (which is at CBUS 0x4000). There is no public documentation available on the actual size of the clock controller's register area (also called "HHI"). However, in Amlogic's GPL kernel sources the last "HHI" register is HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size doesn't seem unlikely. Fixes: 2c323c43a3d619 ("ARM: dts: meson8: add and use the real clock controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-04Merge tag 'socfpga_updates_for_v4.20_part1' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA DTS updates for v4.20 - Rename de0_sockit to de0_nano_soc - Update NAND clocking - Set timer interrupt to edge sensitive - Stratix10 platform updates - Update devkit with correct i2c clock * tag 'socfpga_updates_for_v4.20_part1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: dts: socfpga: Rename socfpga_cyclone5_de0_{sockit,nano_soc} ARM: dts: socfpga: update NAND clocking for c5/a5 ARM: dts: arria10: update NAND clocking ARM: dts: socfpga: set timer interrupt to edge sensitive ARM: dts: socfpga: use stdout-path for chosen node arm64: dts: stratix10: i2c clock running out of spec Signed-off-by: Olof Johansson <olof@lixom.net>
2018-09-04arm64: dts: allwinner: h6: Add OrangePi One Plus initial supportJagan Teki
OrangePi One Plus is Allwinner H6 based open-source SBC, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB LPDDR3 RAM - AXP805 PMIC - 1Gbps GMAC via RTL8211 - USB 2.0 Host, OTG - HDMI port - 5V/2A DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-09-03ARM: dts: at91: tse850: drop three indentation levelsPeter Rosin
Make use of the recently added &pinctrl and &watchdog labels. This makes the whole file consistent and knowledge of the ahb/apb structure is hidden. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-09-03ARM: dts: at91: nattis: drop three indentation levelsPeter Rosin
Make use of the recently added &pinctrl and &watchdog labels. This makes the whole file consistent and knowledge of the ahb/apb structure is hidden. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-09-03ARM: dts: imx7s: enable cpuidle driverAnson Huang
Enable cpuidle for i.MX7S/D using generic ARM cpuidle driver, below 2 idle states enabled: 1. ARM WFI; 2. SoC WAIT mode. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03arm64: dts: ls208xa: add second duartKurt Kanzenbach
The NXP LS208xA SoCs have two dual uarts. Thus, add the second one. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03arm64: dts: fsl: remove big-endian field from IFC controllerPrabhakar Kushwaha
As per IFC binding, Absence of "little-endian" field causes registers access in big-endian mode. So no need to set explicit big-endian field IFC node for LS1043A and LS1046A. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03arm64: dts: Add big-endian in nor node for ls104xaPrabhakar Kushwaha
NOR and IFC controller connectivity is big-endian. So add big-endian field in nor device tree node allowing IFC controller to read/write data from/to the flash correctly. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6sx-sdb: enable gpio buttons as wakeup sourceAnson Huang
This patch enables i.MX6SX SDB board's below GPIO buttons as wakeup sources: SW4(FUNC1): KEY_VOLUMEUP SW5(FUNC2): KEY_VOLUMEDOWN Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx7d-sdb: enable gpio buttons as wakeup sourceAnson Huang
This patch enables i.MX7D SDB board's below GPIO buttons as wakeup sources: S1(FUNC1): KEY_VOLUMEUP S3(FUNC2): KEY_VOLUMEDOWN Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx7s-warp: use SPDX-License-IdentifierPierre-Jean Texier
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: Add big-endian in nor node for ls1021aPrabhakar Kushwaha
NOR and IFC controller connectivity is big-endian. So add big-endian field in nor device tree node allowing IFC controller to read/write data from/to the flash correctly. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03dt-bindings: arm: add missing compatible for i.MX boardsAnson Huang
This patch adds missing compatible for i.MX boards. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6ull-14x14-evk: correct machine model nameAnson Huang
i.MX6ULL is a lite version of i.MX6UL, its full name is i.MX6 UltraLiteLite, NOT UlltraLite. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6sll: add gpio clocksAnson Huang
i.MX6SLL has GPIO clock gates in CCM CCGR, add clock property for GPIO driver to make sure all GPIO banks work as expected. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6ul: Add weim nodeSébastien Szymanski
Add weim node for i.MX6UL SOC. Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6ull: keep IMX6UL_ prefix for signals on both i.MX6UL and i.MX6ULLSébastien Szymanski
Signals available on both i.MX6UL and i.MX6ULL should have the same name because it is the case of all others common signals, it avoids to make mistakes (use the wrong ones) and it makes writing device tree files less complicated. For example: imx6ul-imx6ull-board.dtsi: ... pinctrl_uart5: uart5grp { fsl,pins = < MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1 MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1 >; }; imx6ul-board.dts: #include <imx6ul.dtsi> #include <imx6ul-imx6ull-board.dtsi> ... imx6ull-board.dts: #include <imx6ull.dtsi> #include <imx6ul-imx6ull-board.dtsi> ... Without this patch, the imx6ull-board.dtb will use MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be misconfigured. Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-09-03ARM: dts: imx6qdl-wandboard: Add stdout-pathTuomas Tynkkynen
Setting a stdout-path in the .dtb is convenient because then the user gets a serial console on the RS-232 connector without any extra effort of figuring out the relevant 'console=' boot parameter. Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-27 17:10:11 +0000