| Age | Commit message (Collapse) | Author |
|---|
|
needed for perf_counters.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Reserve a syscall slot for sys_perf_counter_open.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
The pa_pdc_cell struct can be kmalloc'd, so do that
instead.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
The pa_pdc_cell struct can be kmalloc'd, so do that instead.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
arch/parisc/mm/init.c: In function 'free_initmem':
381: warning: passing argument 1 of 'memset' makes pointer from integer without a cast
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Unless I'm totally missing something get_fd_set32/set_fd_set32 are
completely unused.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
The TLB flushing functions on hppa, which causes PxTLB broadcasts on the system
bus, needs to be protected by irq-safe spinlocks to avoid irq handlers to deadlock
the kernel. The deadlocks only happened during I/O intensive loads and triggered
pretty seldom, which is why this bug went so long unnoticed.
Signed-off-by: Helge Deller <deller@gmx.de>
[edited to use spin_lock_irqsave on UP as well since we'd been locking there
all this time anyway, --kyle]
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Rewrote timer_interrupt() to properly handle the "delayed!" case.
If we used floating point math to compute the number of ticks that had
elapsed since the last timer interrupt, it could take up to 12K cycles
(emperical!) to handle the interrupt. Existing code assumed it would
never take more than 8k cycles. We end up programming Interval Timer
to a value less than "current" cycle counter. Thus have to wait until
Interval Timer "wrapped" and would then get the "delayed!" printk that
I moved below.
Since we don't really know what the upper limit is, I prefer to read
CR16 again after we've programmed it to make sure we won't have to
wait for CR16 to wrap.
Further, the printk was between reading CR16 (cycle couner) and writing CR16
(the interval timer). This would cause us to continue to set the interval
timer to a value that was "behind" the cycle counter. Rinse and repeat.
So no printk's between reading CR16 and setting next interval timer.
Tested on A500 (550 Mhz PA8600).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
----
Kyle, Helge, and other parisc's,
Please test on 32-bit before committing.
I think I have it right but recognize I might not.
TODO: I wanted to use "do_div()" in order to get both remainder
and value back with one division op. That should help with the
latency alot but can be applied seperately from this patch.
thanks,
grant
|
|
>>>> I think this is what was intended? Note that this patch may affect
>>>> profiling.
>>> it really should be
>>>
>>> - if (likely(t1 & (sizeof(unsigned int)-1)) == 0) {
>>> + if (likely((t1 & (sizeof(unsigned int)-1)) == 0)) {
>>>
>>> randolph
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
gcc 4.4 warns about:
drivers/parisc/lba_pci.c: In function 'lba_pat_resources':
drivers/parisc/lba_pci.c:1099: warning: the frame size of 8280 bytes is larger than 4096 bytes
The problem is we declare two large structures on the stack. They don't need
to be on the stack since they are only used during LBA initialization (which
is serialized). Moving to be "static".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
This patch modifies parameter of au1x_counter1_read() from 'void' to 'struct
clocksource *cs', which fixes compile warning for incompatible parameter type.
Signed-off-by: Coly Li <coly.li@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Fix this build error:
arch/parisc/math-emu/decode_exc.c:351: undefined reference to `printk'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Fix miscompilation in arch/parisc/kernel/irq.c:
123: warning: passing arg 1 of `cpumask_setall' from incompatible pointer type
141: warning: passing arg 1 of `cpumask_copy' from incompatible pointer type
300: warning: passing arg 1 of `cpumask_copy' from incompatible pointer type
357: warning: passing arg 2 of `cpumask_copy' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Alex Chiang asked me why PARISC was calling pci_bus_add_devices()
and pci_bus_assign_resources() in the opposite order from everyone else.
No reason and I couldn't see any data dependency.
Patch below applies cleanly to 2.6.30-rc2.
Later, I suspected the code worked only because no drivers would be
loaded/ready until much later in the system initialization sequence.
Tested "LBA" code on J6000 (32-bit) and A500 (64-bit SMP) with 2.6.30-rc2.
Not tested with any Dino controllers.
Not tested with PCI-PCI Bridge (TBD).
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
There are two reasons to expose the memory *a in the asm:
1) To prevent the compiler from discarding a preceeding write to *a, and
2) to prevent it from caching *a in a register over the asm.
The change has had a few days testing with a SMP build of 2.6.22.19
running on a rp3440.
This patch is about the correctness of the __ldcw() macro itself.
The use of the macro should be confined to small inline functions
to try to limit the effect of clobbering memory on GCC's optimization
of loads and stores.
Signed-off-by: Dave Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Doing an IPI with local interrupts off triggers a warning. We
don't need to be quite so ridiculously paranoid. Also, clean up
a bit of the code a little.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
The atomic operations on parisc are defined as macros. The macros
includes casts which disallows the use of some syntax elements and
produces error like this:
net/phonet/pep.c: In function 'pipe_rcv_status':
net/phonet/pep.c:262: error: lvalue required as left operand of assignment
The patch removes this superfluous casts.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Fix this build error when CONFIG_PROC_FS is not set:
drivers/parisc/ccio-dma.c:1574: error: 'ccio_proc_info_fops' undeclared
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Fix this build error when CONFIG_STI_CONSOLE is not set
drivers/video/stifb.c:1337: undefined reference to `sti_get_rom'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
Generic compat handlers look appropriate, so use those.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
|
|
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
fs/notify/inotify: decrement user inotify count on close
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix error message formatting
Btrfs: fix use after free in btrfs_start_workers fail path
Btrfs: honor nodatacow/sum mount options for new files
Btrfs: update backrefs while dropping snapshot
Btrfs: account for space we may use in fallocate
Btrfs: fix the file clone ioctl for preallocated extents
Btrfs: don't log the inode in file_write while growing the file
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] cxgb3i: fix connection error when vlan is enabled
[SCSI] FC transport: Locking fix for common-code FC pass-through patch
[SCSI] zalon: fix oops on attach failure
[SCSI] fnic: use DMA_BIT_MASK(nn) instead of deprecated DMA_nnBIT_MASK
[SCSI] fnic: remove redundant BUG_ONs and fix checks on unsigned
[SCSI] ibmvscsi: Fix module load hang
|
|
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
|
|
For some reason, the DP clocks were based off a 100MHz reference instead of
the standard 96MHz reference. This caused some DP monitors to fail to lock
to the signal.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The default configuration file for the KwikByte kb9202 board was based on a 2.6.13-rc2 kernel and doesn't produce a bootable kernel. Update the
configuration in order to produce a bootable image.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It is not safe to use match_int without checking the token type returned
by match_token (especially when the token type returned is Opt_err and
args is empty). Fix it.
Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds ETH_P_1588 protocol ID define.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restrict firmware reset to following cases -
o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.
This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.
Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop a sanity check which doesn't serve any useful purpose anymore.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the use of colors to signal at a glance the important
overhead thresholds in callchains hit rates.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246558475-10624-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Among perf annotate, perf report and perf top, we can find the
common colored printing of percents according to the following
rules:
High overhead = > 5%, colored in red
Mid overhead = > 0.5%, colored in green
Low overhead = < 0.5%, default color
Factorize these multiple checks in a single function named
percent_color_fprintf() and also provide a get_percent_color()
for sites which print percentages and other things at the same
time.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246558475-10624-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Callchains output may become a burden on a trace because even
rarely hit site are exposed. This can be too much information.
Let the user set a threshold as a minimum percent of hits using
the new pattern for the -c option:
-c mode,min_percent
Example:
$ perf report -s sym -c flat,4
8.25% [k] copy_user_generic_string
4.19%
copy_user_generic_string
generic_file_aio_read
do_sync_read
vfs_read
sys_pread64
system_call_fastpath
pread64
5.39% [k] search_by_key
4.63% 0x00000000009e0a
2.36% [k] memcpy_c
[...]
$ perf report -s sym -c graph,2
8.25% [k] copy_user_generic_string
|
|--4.31%-- generic_file_aio_read
| do_sync_read
| vfs_read
| |
| --4.19%-- sys_pread64
| system_call_fastpath
| pread64
|
--3.24%-- generic_file_buffered_write
__generic_file_aio_write_nolock
generic_file_aio_write
do_sync_write
reiserfs_file_write
vfs_write
|
--3.14%-- sys_pwrite64
system_call_fastpath
__pwrite64
5.39% [k] search_by_key
|
--2.23%-- reiserfs_update_sd_size
4.63% 0x00000000009e0a
2.36% [k] memcpy_c
[...]
You can also omit it and it will default to 0.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246558475-10624-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
fix hang with HIGHMEM_64G and 32bit resource. According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.
Analyzed by hpa
Reported-and-tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These macros had two bugs:
- the type of the mask was not correctly expanded to the full size of
the argument being expanded, resulting in possible loss of high bits
when mixing types.
- the alignment argument was evaluated twice, despite the macro looking
like a fancy function (but it really does need to be a macro, since
it works on arbitrary integer types)
Noticed by Peter Anvin, and with a fix that is a modification of his
suggestion (bug noticed by Yinghai Lu).
Cc: Peter Anvin <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the printing of callchains is done in a single
vertical level, this is the "flat" mode:
8.25% [k] copy_user_generic_string
4.19%
copy_user_generic_string
generic_file_aio_read
do_sync_read
vfs_read
sys_pread64
system_call_fastpath
pread64
This patch introduces a new "graph" mode which provides a
hierarchical output of factorized paths recursively sorted:
8.25% [k] copy_user_generic_string
|
|--4.31%-- generic_file_aio_read
| do_sync_read
| vfs_read
| |
| |--4.19%-- sys_pread64
| | system_call_fastpath
| | pread64
| |
| --0.12%-- sys_read
| system_call_fastpath
| __read
|
|--3.24%-- generic_file_buffered_write
| __generic_file_aio_write_nolock
| generic_file_aio_write
| do_sync_write
| reiserfs_file_write
| vfs_write
| |
| |--3.14%-- sys_pwrite64
| | system_call_fastpath
| | __pwrite64
| |
| --0.10%-- sys_write
[...]
The command line has then changed.
By providing the -c option, the callchain will output in the
flat mode by default.
But you can override it:
perf report -c graph
or
perf report -c flat
You can also pass the abreviated mode:
perf report -c g
or
perf report -c gra
will both make use of the graph mode.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246550301-8954-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There is no predefined macro to create an option that can have
a custom value or a default one if none is given.
This patch provides a new helper OPT_CALLBACK_DEFAULT() which
defines such kind of option.
For example, considering an option -c, we want to get the
default value in the following cases:
perf command -c -d
perf command -d -c
And the foo value when it's given:
perf command -c foo -d
perf command -d -c foo
That's also why PARSE_OPT_LASTARG_DEFAULT is extended here to
support default values whatever the position of the option, not
only in the end.
Should it now be renamed to PARSE_OPT_ARG_DEFAULT ?
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: git@vger.kernel.org
LKML-Reference: <1246550301-8954-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Iterating through children of a node in the callchain tree
shows something that may be quite confusing at a first glance.
The head is the children field of the parent and the list nodes
are in the brothers field of the children.
This is because the childs are linked to the parent as a list
of "brothers" using the "children" list of the parent as a
head:
---------------
| Parent (head) |-------------------------------------
--------------- |
| |
children |
| |
----------- ----------- |
| 1st child |---brother---| 2nd child |---brother-----
----------- -----------
This makes the following strange pattern often occuring:
list_for_each_entry(child, &parent->children, brothers) {
// do something with children
}
Abstract it to chain_for_each_child() to factorize and simplify
this pattern.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1246550301-8954-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Make an error msg look nicer by inserting a space between number and word.
Signed-off-by: Hu Tao <hu.taoo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
worker memory is already freed on one fail path in btrfs_start_workers,
but is still dereferenced. Switch the dereference and kfree.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
The btrfs attr patches unconditionally inherited the inode flags field
without honoring nodatacow and nodatasum. This fix makes sure
we properly record the nodatacow/sum mount options in new inodes.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
The new backref format has restriction on type of backref item. If a tree
block isn't referenced by its owner tree, full backrefs must be used for the
pointers in it. When a tree block loses its owner tree's reference, backrefs
for the pointers in it should be updated to full backrefs. Current
btrfs_drop_snapshot misses the code that updates backrefs, so it's unsafe for
general use.
This patch adds backrefs update code to btrfs_drop_snapshot. It isn't a
problem in the restricted form btrfs_drop_snapshot is used today, but for
general snapshot deletion this update is required.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
