| Age | Commit message (Collapse) | Author |
|---|
|
Previously intel_panel_setup_backlight() would create a sysfs backlight
interface with max brightness of 1 if it was unable to figure out the max
backlight brightness. This rendered the backlight interface useless.
Do not create a dysfunctional backlight interface to begin with.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When fq_codel builds a new flow, it should not reset codel state.
Codel algo needs to get previous values (lastcount, drop_next) to get
proper behavior.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dave Taht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
Cc: <stable@vger.kernel.org>
Signed-off-by: Benoît Locher <Benoit.Locher@skf.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
'hwmod_data_fixes_a_3.6rc' into omap_fixes_a_3.6rc
|
|
The OMAP4 sl2if IP block requires some special programming for it to
enter idle. Without this programming, it will prevent the rest of
the chip from entering full chip idle.
This patch comments out the IP block data.
Later, once the appropriate support is available, this patch can be
reverted.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Clock and module mode are explictly enable when hwmod is enabled. But if
the hwmod doesn't get ready on time, clocks are disabled but module is left
enabled.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
IVA2 hwmod resets were missing the status bit offsets. Also, as the
hwmod itself didn't have prcm info at all, resetting iva hwmod was
accessing some bogus memory addresses. Added both infos to fix this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 4da71ae6 ("OMAP: clockdomain: Arch specific funcs for
clkdm_clk_enable/disable") called the OMAP2xxx-specific functions for
clockdomain wakeup and sleep. This would probably have broken
software-supervised clockdomain wakeup and sleep on OMAP3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
|
|
With commit ae6df418a21f3a361c5f9b878e32a8aba4e17692
Sub: ARM: OMAP2+: dmtimer: cleanup fclk usage)
The Timer functional clock naming convention has changed from
gptX_fck => timerXfck, and so as the timer init function
in mach-omap2/timer.c.
OMAP4 clocktree also has changed accordingly.
AM33xx Clock Tree has been merged during rc3-4 timeframe,
before above commit got merged, so similar change is required
for AM33xx as well (Change the gptX_fck => timerX_fck).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Suspending an open usbnet device results in constant
rescheduling of usbnet_bh.
commit 65841fd5 "usbnet: handle remote wakeup asap"
refactored the usbnet_bh code to allow sharing the
urb allocate and submit code with usbnet_resume. In
this process, a test for, and immediate return on,
ENOLINK from rx_submit was unintentionally dropped.
The rx queue will not grow if rx_submit fails,
making usbnet_bh reschedule itself. This results
in a softirq storm if the error is persistent.
rx_submit translates the usb_submit_urb error
EHOSTUNREACH into ENOLINK, so this is an expected
and persistent error for a suspended device. The
old code tested for this condition and avoided
rescheduling. Putting this test back.
Cc: <stable@vger.kernel.org> # v3.5
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via
skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of
sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up
by __sctp_write_space().
Buffer space charged via sctp_set_owner_w() is released in sctp_wfree()
which calls __sctp_write_space() directly.
Buffer space charged via skb_set_owner_w() is released via sock_wfree()
which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set.
sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets.
Therefore if sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is
interrupted by a signal.
This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ...
Charging for the data twice does not make sense in the first place, it
leads to overcharging sndbuf by a factor 2. Therefore this patch only
charges a single byte in wmem_alloc when transmitting an SCTP packet to
ensure that the socket stays alive until the packet has been released.
This means that control chunks are no longer accounted for in wmem_alloc
which I believe is not a problem as skb->truesize will typically lead
to overcharging anyway and thus compensates for any control overhead.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sock_edemux() can handle either a regular socket or a timewait socket
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc 4.6.3 complains about uninitialized variables in fs/fuse/control.c:
CC fs/fuse/control.o
fs/fuse/control.c: In function 'fuse_conn_congestion_threshold_write':
fs/fuse/control.c:165:29: warning: 'val' may be used uninitialized in this function [-Wuninitialized]
fs/fuse/control.c: In function 'fuse_conn_max_background_write':
fs/fuse/control.c:128:23: warning: 'val' may be used uninitialized in this function [-Wuninitialized]
fuse_conn_limit_write() will always return non-zero unless the &val
is modified, so the warning is misleading. Let the compiler know
about it by marking 'val' with 'uninitialized_var'.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
HID_LOGITECH_DJ uses "default m", which enables it in default kernel
builds. Since this module just enables extra, non-critical
functionality for one particular piece of hardware (specifically,
differentiating multiple wireless keyboards and mice as separate input
devices rather than treating them as one device), and the hardware works
just fine with the default USB HID support, drop the "default m".
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git commit cd2934a3 moved the flush_tlb_range() within
__unmap_hugepage_range() inside the mm->page_table_lock, which
triggered a deadlock in s390 tlb flushing code. __tlb_flush_mm_cond()
also tries to acquire the mm->page_table_lock, but that is not needed
because all callers already have mm->mmap_sem or mm->page_table_lock,
so it can be safely removed to fix the deadlock.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
armadillo800eva default boot loader is "hermit",
and it's tag->u.core.flags has flag when kernel boots.
Because of this, ${LINUX}/arch/arm/kernel/setup.c :: parse_tag_core()
didn't remove MS_RDONLY flag from root_mountflags.
Thus, the rootfs is mounted as "readonly".
This patch adds "rw" kernel parameter,
and enable read/write mounts for rootfs
Cc: Masahiro Nakai <nakai@atmark-techno.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
commit 768b107e4b3be0acf6f58e914afe4f337c00932b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri May 4 11:29:56 2012 +0200
drm/i915: disable sdvo hotplug on i945g/gm
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Tested-by: Dominik Köppl <dominik@devwork.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In order to setup the i2c channel, we power up the panel
via ironlake_edp_panel_vdd_on, however it requires
intel_dp->panel_power_up_delay to be initialised,
which hasn't been setup yet.
So move things around so we set the panel power up
values first then init the i2c stuff.
This is one step to fixing the eDP panel in the MBP
from uninitialised state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This was never an error, drop to a debug print.
Reported-by: Keven Lachance
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Pull CIFS fixes from Steve French.
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix cifs_do_create error hadnling
cifs: print error code if smb signature verification fails
CIFS: Fix log messages in packet checking for SMB2
CIFS: Protect i_nlink from being negative
|
|
Pull networking fixes from David Miller:
1) NLA_PUT* --> nla_put_* conversion got one case wrong in
nfnetlink_log, fix from Patrick McHardy.
2) Missed error return check in ipw2100 driver, from Julia Lawall.
3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
from Eric Dumazet.
4) SFC driver erroneously reversed src and dst when reporting filters
via ethtool.
5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
sja1000 can platform driver, from Alexey Khoroshilov and Sven
Schmitt.
6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
take the lock when we really need to. From Eric Dumazet.
7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.
8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
fix from Yuchung Cheng.
9) Revert netpoll change, and fix what was actually a driver specific
problem. From Amerigo Wang. This should cure bootup hangs with
netconsole some people reported.
10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
pointer. From Ian Campbell.
11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.
12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.
13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
situation. From Oliver Neukum.
14) The davinci ethernet driver triggers an OOPS on removal because it
frees an MDIO object before unregistering it. Fix from Bin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net: qmi_wwan: add several new Gobi devices
fddi: 64 bit bug in smt_add_para()
net: ethernet: fix kernel OOPS when remove davinci_mdio module
net/xfrm/xfrm_state.c: fix error return code
net: ipv6: fix error return code
net: qmi_wwan: new device: Foxconn/Novatel E396
usbnet: fix deadlock in resume
cs89x0 : packet reception not working
netfilter: nf_conntrack: fix racy timer handling with reliable events
bnx2x: Correct the ndo_poll_controller call
bnx2x: Move netif_napi_add to the open call
ipv4: must use rcu protection while calling fib_lookup
bnx2x: fix 57840_MF pci id
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
e1000e: DoS while TSO enabled caused by link partner with small MSS
l2tp: avoid to use synchronize_rcu in tunnel free function
gianfar: fix default tx vlan offload feature flag
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
netfilter: nfnetlink_log: fix error return code in init path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen: fixup smsc911x id for regulator
|
|
git://git.infradead.org/users/jcooper/linux into fixes
* 'fixes-for-v3.6-v2' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
|
|
git://anongit.freedesktop.org/nouveau/linux-2.6 into drm-fixes
These two fix the MacBook Pro 2012 Retina display.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nv50-/gpio: initialise to vbios defaults during init
drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs
|
|
Update the comment of hid_have_special_driver[] field to reflect the fact
that multitouch devices don't need to be present there.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Going through the motions of printing the debug message information
takes a long time; using the keyboard can lead to a 160 us irqsoff
latency. This patch skips hid_dump_input() when there are no open
handles, which brings latency down to 100 us.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions. Re-syncing the
list of supported devices with qcserial.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@tempietto.lan>
|
|
The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line. The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@tempietto.lan>
|
|
DIV_ROUND_CLOSEST returns a bad result for negative dividends:
DIV_ROUND_CLOSEST(-2, 2) = 0
Most of the time this does not matter. However, in the hardware monitoring
subsystem, DIV_ROUND_CLOSEST is sometimes used on integers which can be
negative (such as temperatures).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
|
|
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fixing small trivial coding style issues.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
conversion to utf8 left some extra control character here,
remove it.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: John Anthony Kazos Jr <jakj@j-a-k-j.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
MODULE_PARM_DESC for wlan_status is further in the same file
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in drivers/mfd
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If the call to setsockopt() fails in
Documentation/accounting/getdelays.c::create_nl_socket() we return -1
without closing the socket, thus leaking it when the 'fd' variable
goes out of scope.
Easily fixed by just jumping to the 'error' label instead of returning
since we do the proper cleanup there.
While I was there I noticed that the error message that is printet if
setsockopt() fails was broken over two lines - put that on a single
line so it is easier to grep for.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If write fails, remember to close(fd) before returning.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in drivers/mmc
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in drivers/dma.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in drivers/spi
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44471
Reported-by: <rucsoftsec@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in tools/perf.
Signed-off-by: Masanari iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo in tools/testing
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
IOAT has a redefine of PCI Vendor, PCI Subvendor, etc for
PCI_VENDOR_ID_INTEL but they are never used. Remove them.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
HPET_ID_VENDOR_8086 is defined but never used. It would be a redefine
of PCI_VENDOR_ID_INTEL if it was ever used.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Remove PCI vendor IDs, as they are already defined in pci_ids.h.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Achim Leubner <achim_leubner@adaptec.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
