| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Qualcomm ARM Based Driver Updates for v4.12
* Add SCM APIs for restore_sec_cfg and iommu secure page table
* tag 'qcom-drivers-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom_scm: add two scm calls for iommu secure page table
firmware/qcom: add qcom_scm_restore_sec_cfg()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
soc/tegra: Core SoC changes for v4.12-rc1
This contains PMC support for Tegra186 as well as a proper driver for
the flow controller found on SoCs up to Tegra210. This also turns the
fuse driver into an explicitly non-modular driver.
* tag 'tegra-for-4.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
soc: tegra: make fuse-tegra explicitly non-modular
soc/tegra: Fix link errors with PMC disabled
soc/tegra: Implement Tegra186 PMC support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
ARM SOC PM domain support for 4.12
Dave Gerlach (5):
PM / Domains: Add generic data pointer to genpd data struct
PM / Domains: Do not check if simple providers have phandle cells
dt-bindings: Add TI SCI PM Domains
soc: ti: Add ti_sci_pm_domains driver
ARM: keystone: Drop PM domain support for k2g
* tag 'arm-soc-pmdomain' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/drivers
Reset controller changes for v4.12, part 2
Add reset lines for the NAND and eMMC contollers on LD11/LD20 SoCs.
* tag 'reset-for-4.12-2' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier: add NAND and eMMC reset control
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
This adds a new driver for PalmChip PATA controller found on DM6446 and
DM6467 SoCs. This should eventually replace the driver in IDE subsystem.
The patches have been acked by ATA maintainer.
* tag 'davinci-for-v4.12/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
pata_bk3710: clear status bits of BMISP on chipset initialization
pata_bk3710: disable IORDY Timer on chipset initialization
ata: add Palmchip BK3710 PATA controller driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
SCPI update for v4.12
Single patch to optimise the completion initialisation using reinit_*
API instead of full initialisation on each and every transfer.
* tag 'scpi-update-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scpi: reinit completion instead of full init_completion()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
K2G will use a different power domain driver than the rest of the
keystone family in order to make use of the TI SCI protocol so prevent
the standard keystone pm_domain code from registering itself in
preparation for a new driver.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Introduce a ti_sci_pm_domains driver to act as a generic pm domain
provider to allow each device to attach and associate it's ti-sci-id so
that it can be controlled through the TI SCI protocol.
This driver implements a simple genpd where each device node has a
phandle to the power domain node and also must provide an index which
represents the ID to be passed with TI SCI representing the device using
a single phandle cell. The driver manually parses the phandle to get the
cell value. Through this interface the genpd dev_ops start and stop
hooks will use TI SCI to turn on and off each device as determined by
pm_runtime usage.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Add a generic power domain implementation, TI SCI PM Domains, that
will hook into the genpd framework and allow the TI SCI protocol to
control device power states.
Also, provide macros representing each device index as understood
by TI SCI to be used in the device node power-domain references.
These are identifiers for the K2G devices managed by the PMMC.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
There is no reason that a platform genpd driver registered using
of_genpd_add_provider_simple needs to be constrained to having no cells
in the "power-domains" phandle. Currently the genpd framework will fail
if any arguments are passed with for a simple provider but the framework
does not actually care, so remove the check for phandle argument count.
This will allow greater flexibility for genpd providers to use their own
arguments that are passed in the phandle and interpret them however they
see fit.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Add a void *data pointer to struct generic_pm_domain_data. Because this
exists for each device associated with a genpd it will allow us to
assign per-device data if needed on a platform for control of that
specific device.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Tegra132 and Tegra210 support the flowctrl module and so add initial
support for these devices.
Please note that Tegra186 does not support the flowctrl module, so
update the initialisation function such that we do not fall back and
attempt to map the 'hardcoded' address range for Tegra186. Furthermore
64-bit Tegra devices have always had the flowctrl node defined in their
device-tree and so only use the 'hardcoded' addresses for 32-bit Tegra
devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a simple platform driver for the flowctrl module so that it gets
registered as a proper device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The flowctrl driver is required for both ARM and ARM64 Tegra devices
and in order to enable support for it for ARM64, move the Tegra flowctrl
driver into drivers/soc/tegra.
By moving the flowctrl driver, tegra_flowctrl_init() is now called by
via an early initcall and to prevent this function from attempting to
mapping IO space for a non-Tegra device, a test for 'soc_is_tegra()'
is also added.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra flowctrl.h header is included unnecessarily by the Tegra
sleep.S source file. Remove this unnecessary inclusion.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Makefiles currently controlling compilation of this code is:
drivers/soc/tegra/Makefile:obj-y += fuse/
drivers/soc/tegra/fuse/Makefile:obj-y += fuse-tegra.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
With the new Tegra186 PMC driver merged, anything that relies on the previous
PMC driver fails to link when that is disabled:
arch/arm/mach-tegra/pm.o: In function `tegra_pm_set':
pm.c:(.text.tegra_pm_set+0x3c): undefined reference to `tegra_pmc_enter_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_suspend_enter':
pm.c:(.text.tegra_suspend_enter+0x4): undefined reference to `tegra_pmc_get_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_init_suspend':
pm.c:(.init.text+0x1c): undefined reference to `tegra_pmc_get_suspend_mode'
pm.c:(.init.text+0x74): undefined reference to `tegra_pmc_set_suspend_mode'
ERROR: tegra_powergate_sequence_power_up [drivers/ata/ahci_tegra.ko] undefined!
ERROR: tegra_powergate_power_off [drivers/ata/ahci_tegra.ko] undefined!
Making the definition depend on the presence of the driver makes it build
again, though that might not be the correct fix.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 854014236290 ("soc/tegra: Implement Tegra186 PMC support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The power management controller on Tegra186 has changed in backwards-
incompatible ways with respect to earlier generations. This implements a
new driver that supports inversion of the PMU interrupt as well as the
"recovery", "bootloader" and "forced-recovery" reboot commands.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Instead of performing full initialization of the completion structure
on each transfer in scpi_send_message(), we initialize it at boot time
(more specifically, in the relevant probe() function) and use
reinit_completion() to reset ->done counter on each message transfer.
Signed-off-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
into next/drivers
Pull "Broadcom drivers changes for 4.12" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC drivers updates for 4.12,
please pull the following changes:
- Florian updates the Broadcom STB GISB arbiter driver with a bunch of
compatible strings for MIPS-based STBs found under arch/mips/boot/dts/brcm/ in
order for the SoC identification driver to recognize these chips
* tag 'arm-soc/for-4.12/drivers' of http://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Match additional compatible strings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/drivers
Pull "Amlogic driver updates for v4.12" from Kevin Hilman:
- firmware: updates/fixes for meson-sm
* tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
firmware: meson-sm: Allow 0 as valid return value
firmware: meson-sm: Check for buffer output size
|
|
Clear IORDYINT, INTRSTAT and DMAERROR bits of BMISP register
(value '1' needs to be written to the bit to clear it).
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Disable IORDY Timer as the driver doesn't handle IORDY Timer
interrupt anyway.
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add Palmchip BK3710 PATA controller driver.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Those two new SCM calls are needed from qcom-iommu driver in order
to initialize secure iommu page table.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add reset lines for the Denali NAND controller on all UniPhier SoCs,
for the Cadence eMMC controller on LD11/LD20 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Some special SMC calls (i.e. the function used to retrieve the serial
number of the Amlogic SoCs) returns 0 in the register 0 also when the
data was successfully read instead of using the register to hold the
number of bytes returned in the bounce buffer as expected.
With the current implementation of the driver this is seen as an error
and meson_sm_call_read() returns an error even though the data was
correctly read.
To deal with this when we have no information about the amount of read
data (that is 0 is returned by the SMC call) we return to the caller
the requested amount of data and 0 as return value.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
After the data is read by the secure monitor driver it is being copied
in the output buffer checking only the size of the bounce buffer but not
the size of the output buffer.
Fix this in the secure monitor driver slightly changing the API. Fix
also the efuse driver that it is the only driver using this API to not
break bisectability.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # for nvmem
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Renesas ARM Based SoC Drivers Updates for v4.12
* Identify RZ/G1N and RZ/G1H
* tag 'renesas-drivers-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: Identify RZ/G1N
soc: renesas: Identify RZ/G1H
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/drivers
Reset controller changes for v4.12
- make reset drivers with bool Kconfig options explicitly non-modular
- fix uniphier non-static symbol warnings
- fix socfpga nr_resets property
- new drivers for the Arria10 and i.MX7 system reset controllers
- fix sunxi 64-bit compilation
* tag 'reset-for-4.12-1' of git://git.pengutronix.de/git/pza/linux:
reset: sunxi: fix for 64-bit compilation
reset: Add Altera Arria10 SR Reset Controller
dt-bindings: reset: a10sr: Add Arria10 SR Reset Controller offsets
reset: Add i.MX7 SRC reset driver
reset-socfpga: Fix nr_resets property
reset: uniphier: fix non static symbol warnings
reset: pistachio: make it explicitly non-modular
reset: ath79: make it explicitly non-modular
reset: oxnas: make it explicitly non-modular
reset: meson: make it explicitly non-modular
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Allwinner reset controller has 32-bit registers, so translating
the reset cell number into a register and bit offset should not use
any architecture dependent data size. Otherwise this breaks for 64-bit
architectures like arm64.
Fix this by making it clear that it's the hardware register width which
matters here in the calculation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch adds the reset controller functionality for
Peripheral PHYs to the Arria10 System Resource Chip.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The Arria10 System Resource Chip reset controller handles the
Arria10 peripheral PHYs. This patch adds the offsets for
these PHYs.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add reset controller driver exposing various reset faculties,
implemented by System Reset Controller IP block.
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for identifying the RZ/G1N (r8a7744) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for identifying the RZ/G1H (r8a7742) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- four patches to get the new cputime code in shape for s390
- add the new statx system call
- a few bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up statx system call
KVM: s390: Fix guest migration for huge guests resulting in panic
s390/ipl: always use load normal for CCW-type re-IPL
s390/timex: micro optimization for tod_to_ns
s390/cputime: provide archicture specific cputime_to_nsecs
s390/cputime: reset all accounting fields on fork
s390/cputime: remove last traces of cputime_t
s390: fix in-kernel program checks
s390/crypt: fix missing unlock in ctr_paes_crypt on error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- a fix for the kexec/purgatory regression which was introduced in the
merge window via an innocent sparse fix. We could have reverted that
commit, but on deeper inspection it turned out that the whole
machinery is neither documented nor robust. So a proper cleanup was
done instead
- the fix for the TLB flush issue which was discovered recently
- a simple typo fix for a reboot quirk
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tlb: Fix tlb flushing when lguest clears PGE
kexec, x86/purgatory: Unbreak it and clean it up
x86/reboot/quirks: Fix typo in ASUS EeeBook X205TA reboot quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
|
|
Fengguang reported random corruptions from various locations on x86-32
after commits d2852a224050 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79df6a ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.
After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.
There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush. For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.
It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e630a0 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.
Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf95992b
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.
Fixes: c109bf95992b ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull extable.h fix from Paul Gortmaker:
"Fixup for arch/score after extable.h introduction.
It seems that Guenter is the only one on the planet doing builds for
arch/score -- we don't have compile coverage for it in linux-next or
in the kbuild-bot either. Guenter couldn't even recall where he got
his toolchain, but was kind enough to share it with me so I could
validate this change and also add arch/score to my build coverage.
I sat on this a bit in case there was any other fallout in other arch
dirs, but since this still seems to be the only one, I might as well
send it on its way"
* tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
score: Fix implicit includes now failing build after extable change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
|
|
After changing from module.h to extable.h, score builds fail with:
arch/score/kernel/traps.c: In function 'do_ri':
arch/score/kernel/traps.c:248:4: error: implicit declaration of function 'user_disable_single_step'
arch/score/mm/extable.c: In function 'fixup_exception':
arch/score/mm/extable.c:32:38: error: dereferencing pointer to incomplete type
arch/score/mm/extable.c:34:24: error: dereferencing pointer to incomplete type
because extable.h doesn't drag in the same amount of headers as the
module.h did. Add in the headers which were implicitly expected.
Fixes: 90858794c960 ("module.h: remove extable.h include now users have migrated")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[PG: tweak commit log; refresh for sched header refactoring.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes frpm Greg KH:
"Here are two bugfixes for tty stuff for 4.11-rc2.
One of them resolves the pretty bad bug in the n_hdlc code that
Alexander Popov found and fixed and has been reported everywhere. The
other just fixes a samsung serial driver issue when DMA fails on some
systems.
Both have been in linux-next with no reported issues"
* tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Continue to work if DMA request fails
tty: n_hdlc: get rid of racy n_hdlc.tbuf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small build warning fixes for some staging drivers that
Arnd has found on his valiant quest to get the kernel to build
properly with no warnings.
Both of these have been in linux-next this week and resolve the
reported issues"
* tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon: remove unused variable
staging/vc04_services: add CONFIG_OF dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Two smaller pin control fixes for the v4.11 series:
- Add a get_direction() function to the qcom driver
- Fix two pin names in the uniphier driver"
* tag 'pinctrl-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: change pin names of aio/xirq for LD11
pinctrl: qcom: add get_direction function
|
