| Age | Commit message (Collapse) | Author |
|---|
|
In binutils 2.26 a new opcode for the "wait" instruction was added for the
POWER9 and has precedence over the one specific to the e500mc. Commit
ebf714ff3756 ("powerpc/e500mc: Add support for the wait instruction in
e500_idle") uses this instruction specifically on the e500mc to work around
an erratum.
This results in an invalid instruction in idle_e500 when we build for the
e500mc on bintutils >= 2.26 with the default assembler machine type.
Since multiplatform between e500 and non-e500 is not supported, set the
assembler machine type globaly when CONFIG_PPC_E500MC=y.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Vakul Garg <vakul.garg@nxp.com>
CC: Scott Wood <swood@redhat.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This commit fixes a rare but possible case when the clk rate is updated
without update of the regulator voltage.
At boot up, CPUfreq checks if the system is running at the right freq. This
is a sanity check in case a bootloader set clk rate that is outside of freq
table present with cpufreq core. In such cases system can be unstable so
better to change it to a freq that is preset in freq-table.
The CPUfreq takes next freq that is >= policy->cur and this is our
target_freq that needs to be set now.
dev_pm_opp_set_rate(dev, target_freq) checks the target_freq and the
old_freq (a current rate). If these are equal it returns early. If not,
it searches for OPP (old_opp) that fits best to old_freq (not listed in
the table) and updates old_freq (!).
Here, we can end up with old_freq = old_opp.rate = target_freq, which
is not handled in _generic_set_opp_regulator(). It's supposed to update
voltage only when freq > old_freq || freq > old_freq.
if (freq > old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
[...]
if (freq < old_freq) {
ret = _set_opp_voltage(dev, reg, new_supply);
if (ret)
It results in, no voltage update while clk rate is updated.
Example:
freq-table = {
1000MHz 1.15V
666MHZ 1.10V
333MHz 1.05V
}
boot-up-freq = 800MHz # not listed in freq-table
freq = target_freq = 1GHz
old_freq = 800Mhz
old_opp = _find_freq_ceil(opp_table, &old_freq); #(old_freq is modified!)
old_freq = 1GHz
Fixes: 6a0712f6f199 ("PM / OPP: Add dev_pm_opp_set_rate()")
Cc: 4.6+ <stable@vger.kernel.org> # v4.6+
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
It happens when enable debug log, if set_alt() returns
USB_GADGET_DELAYED_STATUS and usb_composite_setup_continue()
is called before increasing count of @delayed_status,
so fix it by using spinlock of @cdev->lock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Jay Hsu <shih-chieh.hsu@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The commit 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048f5 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The #ifdef guards around these are wrong, resulting in warnings
in certain configurations:
drivers/usb/dwc3/dwc3-qcom.c:244:12: error: 'dwc3_qcom_resume' defined but not used [-Werror=unused-function]
static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
^~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:223:12: error: 'dwc3_qcom_suspend' defined but not used [-Werror=unused-function]
static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
This replaces the guards with __maybe_unused annotations to shut up
the warnings and give better compile time coverage.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add ONFI_FEATURE_ON_DIE_ECC to the set/get features list for Micron
NAND flash.
Fixes: 789157e41a06 ("mtd: rawnand: allow vendors to declare (un)supported features")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add device remove and module exit code to make the driver
functioning as a loadable module.
Fixes: ac28927659be (cpufreq: kryo: allow building as a loadable module)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In event of error returned by the nvmem_cell_read() non-pointer value
may be dereferenced. Fix this with error handling.
Additionally free the allocated speedbin buffer, as per the API.
Fixes: 9ce36edd1a52 (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit b5793b0d92c9 added support for building the nanosleep compat system
call on 32-bit architectures, but missed one change in nanosleep_copyout(),
which would trigger a BUG() as soon as any architecture is switched over to
use it.
Use the proper config symbol to enable the code path.
Fixes: Commit b5793b0d92c9 ("posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: y2038@lists.linaro.org
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20180618140811.2998503-1-arnd@arndb.de
|
|
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5c5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 80c49563e250 ("scsi: scsi_debug: implement IMMED bit") there
are long delays in F_SYNC_DELAY and F_SSU_DELAY. This can cause a memory
leak in schedule_resp(), which can be invoked while unloading the
scsi_debug module: free_all_queued() had already freed all sd_dp and
schedule_resp will alloc a new one, which will never get freed. Here's the
kmemleak report while running xfstests generic/350:
unreferenced object 0xffff88007d752b00 (size 128):
comm "rmmod", pid 26940, jiffies 4295816945 (age 7.588s)
hex dump (first 32 bytes):
00 2b 75 7d 00 88 ff ff 00 00 00 00 00 00 00 00 .+u}............
00 00 00 00 00 00 00 00 8e 31 a2 34 5f 03 00 00 .........1.4_...
backtrace:
[<000000002abd83d0>] 0xffffffffa000705e
[<000000004c063fda>] scsi_dispatch_cmd+0xc7/0x1a0
[<000000000c119a00>] scsi_request_fn+0x251/0x550
[<000000009de0c736>] __blk_run_queue+0x3f/0x60
[<000000001c4453c8>] blk_execute_rq_nowait+0x98/0xd0
[<00000000d17ec79f>] blk_execute_rq+0x3a/0x50
[<00000000a7654b6e>] scsi_execute+0x113/0x250
[<00000000fd78f7cd>] sd_sync_cache+0x95/0x160
[<0000000024dacb14>] sd_shutdown+0x9b/0xd0
[<00000000e9101710>] sd_remove+0x5f/0xb0
[<00000000c43f0d63>] device_release_driver_internal+0x13c/0x1f0
[<00000000e8ad57b6>] bus_remove_device+0xe9/0x160
[<00000000713a7b8a>] device_del+0x120/0x320
[<00000000e5db670c>] __scsi_remove_device+0x115/0x150
[<00000000eccbef30>] scsi_forget_host+0x20/0x60
[<00000000cd5a0738>] scsi_remove_host+0x6d/0x120
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The patch reverts changes done in qlt_schedule_sess_for_deletion() to
avoid spinlock recursion sess->vha->work_lock should be used instead
of ha->tgt.sess_lock, that can be locked in callers: qlt_reset() or
qlt_handle_login()
[mkp: roll in build warning reported by sfr]
Fixes: 1c6cacf4ea6c04 ("scsi: qla2xxx: Fixup locking for session deletion")
Cc: <stable@vger.kernel.org> #v4.17
Signed-off-by: Mikhail Malygin <m.malygin@yadro.com>
Reported-by: Mikhail Malygin <m.malygin@yadro.com>
Tested-by: Mikhail Malygin <m.malygin@yadro.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver does both wmb() and writel(). The latter already has a barrier
on some architectures like arm64. This ends up with CPU observing two
barriers back to back before executing the register write.
Drivers should generally assume that the barrier implied by writel() is
sufficient for ordering DMA. Remove the extraneous wmb() before it.
[mkp: Squashed Arnd's and Sinan's patches]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Generally target core and TCMUser seem to work fine for tape devices and
media changers. But there is at least one situation where TCMUser is not
able to support sequential access device emulation correctly.
The situation is when an initiator sends a SCSI READ CDB with a length that
is greater than the length of the tape block to read. We can distinguish
two subcases:
A) The initiator sent the READ CDB with the SILI bit being set.
In this case the sequential access device has to transfer the data from
the tape block (only the length of the tape block) and transmit a good
status. The current interface between TCMUser and the userspace does
not support reduction of the read data size by the userspace program.
The patch below fixes this subcase by allowing the userspace program to
specify a reduced data size in read direction.
B) The initiator sent the READ CDB with the SILI bit not being set.
In this case the sequential access device has to transfer the data from
the tape block as in A), but additionally has to transmit CHECK
CONDITION with the ILI bit set and NO SENSE in the sensebytes. The
information field in the sensebytes must contain the residual count.
With the below patch a user space program can specify the real read data
length and appropriate sensebytes. TCMUser then uses the se_cmd flag
SCF_TREAT_READ_AS_NORMAL, to force target core to transmit the real data
size and the sensebytes. Note: the flag SCF_TREAT_READ_AS_NORMAL is
introduced by Lee Duncan's patch "[PATCH v4] target: transport should
handle st FM/EOM/ILI reads" from Tue, 15 May 2018 18:25:24 -0700.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Ctxdmas for cursors from all heads are setup in the core channel, and due
to us tracking allocated handles per-window, we were failing with -EEXIST
on multiple-head setups trying to allocate duplicate handles.
The cursor code is hardcoded to use the core channel vram ctxdma already,
so just skip ctxdma allocation for cursor fbs to fix the issue.
Fixes: 5bca1621c07 ("drm/nouveau/kms/nv50-: move fb ctxdma tracking into windows")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull jfs fix from Dave Kleikamp:
"This fixes a too-small allocation in the xattr code"
* tag 'jfs-4.18' of git://github.com/kleikamp/linux-shaggy:
jfs: Fix inconsistency between memory allocation and ea_buf->max_size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"common I/O layer
- Fix bit-fields crossing storage-unit boundaries in css_general_char
dasd driver
- Avoid a sparse warning in regard to the queue lock
- Allocate the struct dasd_ccw_req as per request data. Only for
internal I/O is the structure allocated separately
- Remove the unused function dasd_kmalloc_set_cda
- Save a few bytes in struct dasd_ccw_req by reordering fields
- Convert remaining users of dasd_kmalloc_request to
dasd_smalloc_request and remove the now unused function
vfio/ccw
- Refactor and improve pfn_array_alloc_pin/pfn_array_pin
- Add a new tracepoint for failed vfio/ccw requests
- Add a CCW translation improvement to accept more requests as valid
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: only use preallocated requests
s390/dasd: reshuffle struct dasd_ccw_req
s390/dasd: remove dasd_kmalloc_set_cda
s390/dasd: move dasd_ccw_req to per request data
s390/dasd: simplify locking in process_final_queue
s390/cio: sanitize css_general_characteristics definition
vfio: ccw: add tracepoints for interesting error paths
vfio: ccw: set ccw->cda to NULL defensively
vfio: ccw: refactor and improve pfn_array_alloc_pin()
vfio: ccw: shorten kernel doc description for pfn_array_pin()
vfio: ccw: push down unsupported IDA check
vfio: ccw: fix error return in vfio_ccw_sch_event
s390/archrandom: Rework arch random implementation.
s390/net: add pnetid support
|
|
The patch fixed a W=1 warning but broke the ia64 build:
CC mm/memblock.o
mm/memblock.c:1340: error: redefinition of `memblock_virt_alloc_try_nid_raw'
./include/linux/bootmem.h:335: error: previous definition of `memblock_virt_alloc_try_nid_raw' was here
Because inlcude/linux/bootmem.h says
#if defined(CONFIG_HAVE_MEMBLOCK) && defined(CONFIG_NO_BOOTMEM)
whereas mm/Makefile says
obj-$(CONFIG_HAVE_MEMBLOCK) += memblock.o
So revert 26f09e9b3a06 ("mm/memblock: add missing include
<linux/bootmem.h>") while a full fix can be worked on.
Fixes: 26f09e9b3a06 ("mm/memblock: add missing include <linux/bootmem.h>")
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
And update my email address.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19461/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
I used bad names in my clumsiness when rewriting many board
files to use GPIO descriptors instead of platform data. A few
had the platform_device ID set to -1 which would indeed give
the device name "i2c-gpio".
But several had it set to >=0 which gives the names
"i2c-gpio.0", "i2c-gpio.1" ...
Fix the one affected board in the MIPS tree. Sorry.
Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors")
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19387/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Run the completer task to post a work completion after processing
a memory registration or invalidate work request. This covers the
case where the memory registration or invalidate was the last work
request posted to the qp.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Few kernel applications like SCST-iSER create CQ using ib_create_cq(),
where accessing CQ structures using rdma restrack tool leads to below NULL
pointer dereference. This patch saves caller kernel module name similar to
ib_alloc_cq().
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8132ca70>] skip_spaces+0x30/0x30
PGD 738bac067 PUD 8533f0067 PMD 0
Oops: 0000 [#1] SMP
R10: ffff88017fc03300 R11: 0000000000000246 R12: 0000000000000000
R13: ffff88082fa5a668 R14: ffff88017475a000 R15: 0000000000000000
FS: 00002b32726582c0(0000) GS:ffff88087fc40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000008491a1000 CR4: 00000000003607e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffffc05af69c>] ? fill_res_name_pid+0x7c/0x90 [ib_core]
[<ffffffffc05af79f>] fill_res_cq_entry+0xef/0x170 [ib_core]
[<ffffffffc05af4c4>] res_get_common_dumpit+0x3c4/0x480 [ib_core]
[<ffffffffc05af5d3>] nldev_res_get_cq_dumpit+0x13/0x20 [ib_core]
[<ffffffff815bc1e7>] netlink_dump+0x117/0x2e0
[<ffffffff815bcb8b>] __netlink_dump_start+0x1ab/0x230
[<ffffffffc059fead>] ibnl_rcv_msg+0x11d/0x1f0 [ib_core]
[<ffffffffc05af5c0>] ? nldev_res_get_mr_dumpit+0x20/0x20 [ib_core]
[<ffffffffc059fd90>] ? rdma_nl_multicast+0x30/0x30 [ib_core]
[<ffffffff815bea49>] netlink_rcv_skb+0xa9/0xc0
[<ffffffffc05a0018>] ibnl_rcv+0x98/0xb0 [ib_core]
[<ffffffff815be132>] netlink_unicast+0xf2/0x1b0
[<ffffffff815be50f>] netlink_sendmsg+0x31f/0x6a0
[<ffffffff8156b580>] sock_sendmsg+0xb0/0xf0
[<ffffffff816ace9e>] ? _raw_spin_unlock_bh+0x1e/0x20
[<ffffffff8156f998>] ? release_sock+0x118/0x170
[<ffffffff8156b731>] SYSC_sendto+0x121/0x1c0
[<ffffffff81568340>] ? sock_alloc_file+0xa0/0x140
[<ffffffff81221265>] ? __fd_install+0x25/0x60
[<ffffffff8156c2ce>] SyS_sendto+0xe/0x10
[<ffffffff816b6c2a>] system_call_fastpath+0x16/0x1b
RIP [<ffffffff8132ca70>] skip_spaces+0x30/0x30
RSP <ffff88072be97760>
CR2: 0000000000000000
Cc: <stable@vger.kernel.org>
Fixes: f66c8ba4c9fa ("RDMA/core: Save kernel caller name when creating PD and CQ objects")
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The width and height needs to be swapped
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[rebased on top of v4.18-rc1]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
On some Mali-DP processors, the LAYER_FORMAT register contains fields
other than the format. These bits were unconditionally cleared when
setting the pixel format, whereas they should be preserved at their
reset values.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
encoder/connector
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
This patch fixes the below parser error of the IOB SLOW PMU.
# perf stat -a -e iob-slow0/cycle-count/ sleep 1
evenf syntax error: 'iob-slow0/cycle-count/'
\___ parser error
It replaces the "-" character by "_" character inside the PMU name.
Signed-off-by: Hoan Tran <hoan.tran@amperecomputing.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Fix I2C controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Stingray SoC.
Fixes: 1256ea18875d ("arm64: dts: Add I2C DT nodes for Stingray SoC")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
NS2 SoC.
Fixes: fd5e5dd56a2f ("arm64: dts: Add PCIe0 and PCIe4 DT nodes for NS2")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix I2C controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom NS2
SoC.
Fixes: 7ac674e8df7a ("arm64: dts: Add I2C nodes for NS2")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Specify 1.8V EMMC capabilities for bcm958742t board to indicate support
for UHS mode.
Fixes: d4b4aba6be8a ("arm64: dts: Initial DTS files for Broadcom Stingray SOC")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Specify 1.8V EMMC capabilities for bcm958742k board to indicate support
for UHS mode.
Fixes: d4b4aba6be8a ("arm64: dts: Initial DTS files for Broadcom Stingray SOC")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a936 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a82 ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix I2C controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC.
Fixes: b51c05a331ff ("ARM: dts: add I2C device nodes for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e0045 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb9412088 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029fdc ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d09 ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Update the MAINTAINERS file to cover the "stingray" pattern and a few
files under arch/arm64/boot/dts/broadcom/* as well as the clock driver
and binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
While moving the Northstar 2 DTS into a dedicated directory, the
corresponding MAINTAINERS file entry was not updated accordingly, fix
that.
Fixes: 63a913c157f5 ("arm64: dts: move ns2 into northstar2 directory")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add missing SPDX License Identifiers to Makefile(s).
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Tom Hromatka <tom.hromatka@oracle.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
|
