| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only two left-over remaining non-urgent ARM SoC bug fixes:
- A build fix for the Atmel SAM9 platform to allow building with the
clang integrated assembler
- A DT fix for ethernet on Intel SoCFPGA, this has been broken since
it was added in v5.4"
* tag 'arm-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: at91: use proper asm syntax in pm_suspend
arm64: dts: agilex: fix phy interface bit shift for gmac1 and gmac2
|
|
Pull networking updates from David Miller:
"Here is what we have this merge window:
1) Support SW steering for mlx5 Connect-X6Dx, from Yevgeny Kliteynik.
2) Add RSS multi group support to octeontx2-pf driver, from Geetha
Sowjanya.
3) Add support for KS8851 PHY. From Marek Vasut.
4) Add support for GarfieldPeak bluetooth controller from Kiran K.
5) Add support for half-duplex tcan4x5x can controllers.
6) Add batch skb rx processing to bcrm63xx_enet, from Sieng Piaw
Liew.
7) Rework RX port offload infrastructure, particularly wrt, UDP
tunneling, from Jakub Kicinski.
8) Add BCM72116 PHY support, from Florian Fainelli.
9) Remove Dsa specific notifiers, they are unnecessary. From Vladimir
Oltean.
10) Add support for picosecond rx delay in dwmac-meson8b chips. From
Martin Blumenstingl.
11) Support TSO on xfrm interfaces from Eyal Birger.
12) Add support for MP_PRIO to mptcp stack, from Geliang Tang.
13) Support BCM4908 integrated switch, from Rafał Miłecki.
14) Support for directly accessing kernel module variables via module
BTF info, from Andrii Naryiko.
15) Add DASH (esktop and mobile Architecture for System Hardware)
support to r8169 driver, from Heiner Kallweit.
16) Add rx vlan filtering to dpaa2-eth, from Ionut-robert Aron.
17) Add support for 100 base0x SFP devices, from Bjarni Jonasson.
18) Support link aggregation in DSA, from Tobias Waldekranz.
19) Support for bitwidse atomics in bpf, from Brendan Jackman.
20) SmartEEE support in at803x driver, from Russell King.
21) Add support for flow based tunneling to GTP, from Pravin B Shelar.
22) Allow arbitrary number of interconnrcts in ipa, from Alex Elder.
23) TLS RX offload for bonding, from Tariq Toukan.
24) RX decap offklload support in mac80211, from Felix Fietkou.
25) devlink health saupport in octeontx2-af, from George Cherian.
26) Add TTL attr to SCM_TIMESTAMP_OPT_STATS, from Yousuk Seung
27) Delegated actionss support in mptcp, from Paolo Abeni.
28) Support receive timestamping when doin zerocopy tcp receive. From
Arjun Ray.
29) HTB offload support for mlx5, from Maxim Mikityanskiy.
30) UDP GRO forwarding, from Maxim Mikityanskiy.
31) TAPRIO offloading in dsa hellcreek driver, from Kurt Kanzenbach.
32) Weighted random twos choice algorithm for ipvs, from Darby Payne.
33) Fix netdev registration deadlock, from Johannes Berg.
34) Various conversions to new tasklet api, from EmilRenner Berthing.
35) Bulk skb allocations in veth, from Lorenzo Bianconi.
36) New ethtool interface for lane setting, from Danielle Ratson.
37) Offload failiure notifications for routes, from Amit Cohen.
38) BCM4908 support, from Rafał Miłecki.
39) Support several new iwlwifi chips, from Ihab Zhaika.
40) Flow drector support for ipv6 in i40e, from Przemyslaw Patynowski.
41) Support for mhi prrotocols, from Loic Poulain.
42) Optimize bpf program stats.
43) Implement RFC6056, for better port randomization, from Eric
Dumazet.
44) hsr tag offloading support from George McCollister.
45) Netpoll support in qede, from Bhaskar Upadhaya.
46) 2005/400g speed support in bonding 3ad mode, from Nikolay
Aleksandrov.
47) Netlink event support in mptcp, from Florian Westphal.
48) Better skbuff caching, from Alexander Lobakin.
49) MRP (Media Redundancy Protocol) offloading in DSA and a few
drivers, from Horatiu Vultur.
50) mqprio saupport in mvneta, from Maxime Chevallier.
51) Remove of_phy_attach, no longer needed, from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1766 commits)
octeontx2-pf: Fix otx2_get_fecparam()
cteontx2-pf: cn10k: Prevent harmless double shift bugs
net: stmmac: Add PCI bus info to ethtool driver query output
ptp: ptp_clockmatrix: clean-up - parenthesis around a == b are unnecessary
ptp: ptp_clockmatrix: Simplify code - remove unnecessary `err` variable.
ptp: ptp_clockmatrix: Coding style - tighten vertical spacing.
ptp: ptp_clockmatrix: Clean-up dev_*() messages.
ptp: ptp_clockmatrix: Remove unused header declarations.
ptp: ptp_clockmatrix: Add alignment of 1 PPS to idtcm_perout_enable.
ptp: ptp_clockmatrix: Add wait_for_sys_apll_dpll_lock.
net: stmmac: dwmac-sun8i: Add a shutdown callback
net: stmmac: dwmac-sun8i: Minor probe function cleanup
net: stmmac: dwmac-sun8i: Use reset_control_reset
net: stmmac: dwmac-sun8i: Remove unnecessary PHY power check
net: stmmac: dwmac-sun8i: Return void from PHY unpower
r8169: use macro pm_ptr
net: mdio: Remove of_phy_attach()
net: mscc: ocelot: select PACKING in the Kconfig
net: re-solve some conflicts after net -> net-next merge
net: dsa: tag_rtl4_a: Support also egress tags
...
|
|
After switching to non-RCU mode, we want nd->depth to match the number
of entries in nd->stack[] that need eventual path_put().
legitimize_links() takes care of that on failures; unfortunately,
failure exits added for LOOKUP_CACHED do not.
We could add the logics for that into those failure exits, both in
try_to_unlazy() and in try_to_unlazy_next(), but since both checks
are immediately followed by legitimize_links() and there's no calls
of legitimize_links() other than those two... It's easier to
move the check (and required handling of nd->depth on failure) into
legitimize_links() itself.
[caught by Jens: ... and since we are zeroing ->depth here, we need
to do drop_links() first]
Fixes: 6c6ec2b0a3e0 "fs: add support for LOOKUP_CACHED"
Tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Fixes the following sparse warnings:
i40e_main.c:5953:32: warning: cast from restricted __le16
i40e_main.c:8008:29: warning: incorrect type in assignment (different base types)
i40e_main.c:8008:29: expected unsigned int [assigned] [usertype] ipa
i40e_main.c:8008:29: got restricted __le32 [usertype]
i40e_main.c:8008:29: warning: incorrect type in assignment (different base types)
i40e_main.c:8008:29: expected unsigned int [assigned] [usertype] ipa
i40e_main.c:8008:29: got restricted __le32 [usertype]
i40e_txrx.c:1950:59: warning: incorrect type in initializer (different base types)
i40e_txrx.c:1950:59: expected unsigned short [usertype] vlan_tag
i40e_txrx.c:1950:59: got restricted __le16 [usertype] l2tag1
i40e_txrx.c:1953:40: warning: cast to restricted __le16
i40e_xsk.c:448:38: warning: invalid assignment: |=
i40e_xsk.c:448:38: left side has type restricted __le64
i40e_xsk.c:448:38: right side has type int
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: 2a508c64ad27 ("i40e: fix VLAN.TCI == 0 RX HW offload")
Fixes: 3106c580fb7c ("i40e: Use batched xsk Tx interfaces to increase performance")
Fixes: 8f88b3034db3 ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix insufficient distinction between IPv4 and IPv6 addresses
when creating a filter.
IPv4 and IPv6 are kept in the same memory area. If IPv6 is added,
then it's caught by IPv4 check, which leads to err -95.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Both pstore_compress() and decompress_record() use a mistyped config
option name ("PSTORE_COMPRESSION" instead of "PSTORE_COMPRESS"). As
a result compression and decompression of pstore records was always
disabled.
Use the correct config option name.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Fixes: fd49e03280e5 ("pstore: Fix linking when crypto API disabled")
Acked-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210218111547.johvp5klpv3xrpnn@dwarf.suse.cz
|
|
When creating VFs they were sometimes not getting resources.
It was caused by not executing i40e_reset_all_vfs due to
flag __I40E_VF_DISABLE being set on PF. Because of this
IAVF was never able to finish setup sequence never
getting reset indication from PF.
Changed test_and_set_bit __I40E_VF_DISABLE in
i40e_sync_filters_subtask to test_bit and removed clear_bit.
This function should not set this bit it should only check
if it hasn't been already set.
Fixes: a7542b876075 ("i40e: check __I40E_VF_DISABLE bit in i40e_sync_filters_subtask")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix addition of VLAN filter for PF after enabling FW LLDP agent.
Changing LLDP Agent causes FW to re-initialize per NVM settings.
Remove default PF filter and move "Enable/Disable" to currently used
reset flag.
Without this patch PF would try to add MAC VLAN filter with default
switch filter present. This causes AQ error and sets promiscuous mode
on.
Fixes: c65e78f87f81 ("i40e: Further implementation of LLDP")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During driver loading flow control settings were written to FW
using a variable which was always zero, since it was being set
only by ethtool. This behavior has been corrected and driver
no longer overwrites the default FW/NVM settings.
Fixes: 373149fc99a0 ("i40e: Decrease the scope of rtnl lock")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Zero-initialize AQ command data structures to comply with
API specifications.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: f4492db16df8 ("i40e: Add NPAR BW get and set functions")
Signed-off-by: Andrzej Sawuła <andrzej.sawula@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with I40E_TX_CTX_EXT_IP_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a3fd9d8876a5 ("i40e/i40evf: Handle IPv6 extension headers in checksum offload")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Static checkers complained about an off by one read overflow in
otx2_get_fecparam() and we applied two conflicting fixes for it.
Correct: b0aae0bde26f ("octeontx2: Fix condition.")
Wrong: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Revert the incorrect fix.
Fixes: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These defines are used with set_bit() and test_bit() which take a bit
number. In other words, the code is doing:
if (BIT(BIT(1)) & pf->hw.cap_flag) {
This was done consistently so it did not cause a problem at runtime but
it's still worth fixing.
Fixes: facede8209ef ("octeontx2-pf: cn10k: Add mbox support for CN10K")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch populates the PCI bus info in the ethtool driver query data.
Users will be able to view PCI bus info using 'ethtool -i <interface>'.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vincent Cheng says:
====================
ptp: ptp_clockmatrix: Fix output 1 PPS alignment.
This series fixes a race condition that may result in the output clock
not aligned to internal 1 PPS clock.
Part of device initialization is to align the rising edge of output
clocks to the internal rising edge of the 1 PPS clock. If the system
APLL and DPLL are not locked when this alignment occurs, the alignment
fails and a fixed offset between the internal 1 PPS clock and the
output clock occurs.
If a clock is dynamically enabled after power-up, the output clock
also needs to be aligned to the internal 1 PPS clock.
v3:
Suggested by: Jakub Kicinski <kuba@kernel.org>
- Remove unnecessary 'err' variable
- Increase msleep()/loop accuracy by using jiffies in while()
- No empty lines between variables
- No empty lines between call and the if
- parenthesis around a == b are unnecessary
- Inconsistent \n usage in dev_()
- Remove unnecessary empty line
- Leave string format in place so static code checkers can
validate arguments
v2:
Suggested by: Richard Cochran <richardcochran@gmail.com>
- Added const to "char * fmt"
- Break unrelated header change into separate patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
* Remove blank line between variable declarations.
* Remove blank line between:
err = blah(...)
if (err)
...
* Remove unnecessary blank line before/after loop constructs.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code clean-up.
* Remove unnecessary \n termination from dev_*() messages.
* Remove 'char *fmt' to define strings to stay within 80 column
limit. Not needed since coding guidelines increased to
100 columns limit.
Keeping format in place allows static code checkers to
validate the arguments.
* Tighten up vertical spacing.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed unused header declarations.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling output using PTP_CLK_REQ_PEROUT, need to align the output
clock to the internal 1 PPS clock.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Part of the device initialization aligns the rising edge of the output
clock to the internal 1 PPS clock. If the system APLL and DPLL is not
locked, then the alignment will fail and there will be a fixed offset
between the internal 1 PPS clock and the output clock.
After loading the device firmware, poll the system APLL and DPLL for
locked state prior to initialization, timing out after 2 seconds.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Samuel Holland says:
====================
dwmac-sun8i cleanup and shutdown hook
These patches clean up some things I noticed while fixing suspend/resume
behavior. The first four are minor code improvements. The last one adds
a shutdown hook to minimize power consumption on boards without a PMIC.
Changes v1 to v2:
- Note the assumption of exclusive reset controller access in patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet MAC and PHY are usually major consumers of power on boards
which may not be able to fully power off (those with no PMIC). Powering
down the MAC and internal PHY saves power while these boards are "off".
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the spacing and use an explicit "return 0" in the success path
to make the function easier to parse.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the appropriate function instead of reimplementing it,
and update the error message to match the code.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sun8i_dwmac_unpower_internal_phy already checks if the PHY is powered,
so there is no need to do it again here.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a deinitialization function that always returned zero, and that
return value was always ignored. Have it return void instead.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use macro pm_ptr(), this helps to avoid some ifdeffery.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add two helper functions to release one table and hooks from
the netns and netlink event path.
2) Add table ownership infrastructure, this new infrastructure allows
users to bind a table (and its content) to a process through the
netlink socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have no in-tree users, also update the sfp-phylink.rst documentation
to indicate that phy_attach_direct() is used instead of of_phy_attach().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot now uses include/linux/dsa/ocelot.h which makes use of
CONFIG_PACKING to pack/unpack bits into the Injection/Extraction Frame
Headers. So it needs to explicitly select it, otherwise there might be
build errors due to the missing dependency.
Fixes: 40d3f295b5fe ("net: mscc: ocelot: use common tag parsing code with DSA")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow building x86 with PREEMPT_DYNAMIC=n, this is needed for
PREEMPT_RT as it makes no sense to not have full preemption on
PREEMPT_RT.
Fixes: 8c98e8cf723c ("preempt/dynamic: Provide preempt_schedule[_notrace]() static calls")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Mike Galbraith <efault@gmx.de>
Link: https://lkml.kernel.org/r/YCK1+JyFNxQnWeXK@hirez.programming.kicks-ass.net
|
|
Following the idle loop model, cleanly check for pending rcuog wakeup
before the last rescheduling point upon resuming to guest mode. This
way we can avoid to do it from rcu_user_enter() with the last resort
self-IPI hack that enforces rescheduling.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-6-frederic@kernel.org
|
|
Following the idle loop model, cleanly check for pending rcuog wakeup
before the last rescheduling point on resuming to user mode. This
way we can avoid to do it from rcu_user_enter() with the last resort
self-IPI hack that enforces rescheduling.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-5-frederic@kernel.org
|
|
Entering RCU idle mode may cause a deferred wake up of an RCU NOCB_GP
kthread (rcuog) to be serviced.
Unfortunately the call to rcu_user_enter() is already past the last
rescheduling opportunity before we resume to userspace or to guest mode.
We may escape there with the woken task ignored.
The ultimate resort to fix every callsites is to trigger a self-IPI
(nohz_full depends on arch to implement arch_irq_work_raise()) that will
trigger a reschedule on IRQ tail or guest exit.
Eventually every site that want a saner treatment will need to carefully
place a call to rcu_nocb_flush_deferred_wakeup() before the last explicit
need_resched() check upon resume.
Fixes: 96d3fd0d315a (rcu: Break call_rcu() deadlock involving scheduler and perf)
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-4-frederic@kernel.org
|
|
Entering RCU idle mode may cause a deferred wake up of an RCU NOCB_GP
kthread (rcuog) to be serviced.
Usually a local wake up happening while running the idle task is handled
in one of the need_resched() checks carefully placed within the idle
loop that can break to the scheduler.
Unfortunately the call to rcu_idle_enter() is already beyond the last
generic need_resched() check and we may halt the CPU with a resched
request unhandled, leaving the task hanging.
Fix this with splitting the rcuog wakeup handling from rcu_idle_enter()
and place it before the last generic need_resched() check in the idle
loop. It is then assumed that no call to call_rcu() will be performed
after that in the idle loop until the CPU is put in low power mode.
Fixes: 96d3fd0d315a (rcu: Break call_rcu() deadlock involving scheduler and perf)
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-3-frederic@kernel.org
|
|
Deferred wakeup of rcuog kthreads upon RCU idle mode entry is going to
be handled differently whether initiated by idle, user or guest. Prepare
with pulling that control up to rcu_eqs_enter() callers.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-2-frederic@kernel.org
|
|
The HRTICK feature has traditionally been servicing configurations that
need precise preemptions point for NORMAL tasks. More recently, the
feature has been extended to also service DEADLINE tasks with stringent
runtime enforcement needs (e.g., runtime < 1ms with HZ=1000).
Enabling HRTICK sched feature currently enables the additional timer and
task tick for both classes, which might introduced undesired overhead
for no additional benefit if one needed it only for one of the cases.
Separate HRTICK sched feature in two (and leave the traditional case
name unmodified) so that it can be selectively enabled when needed.
With:
$ echo HRTICK > /sys/kernel/debug/sched_features
the NORMAL/fair hrtick gets enabled.
With:
$ echo HRTICK_DL > /sys/kernel/debug/sched_features
the DEADLINE hrtick gets enabled.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210208073554.14629-3-juri.lelli@redhat.com
|
|
Hung tasks and RCU stall cases were reported on systems which were not
100% busy. Investigation of such unexpected cases (no sign of potential
starvation caused by tasks hogging the system) pointed out that the
periodic sched tick timer wasn't serviced anymore after a certain point
and that caused all machinery that depends on it (timers, RCU, etc.) to
stop working as well. This issues was however only reproducible if
HRTICK was enabled.
Looking at core dumps it was found that the rbtree of the hrtimer base
used also for the hrtick was corrupted (i.e. next as seen from the base
root and actual leftmost obtained by traversing the tree are different).
Same base is also used for periodic tick hrtimer, which might get "lost"
if the rbtree gets corrupted.
Much alike what described in commit 1f71addd34f4c ("tick/sched: Do not
mess with an enqueued hrtimer") there is a race window between
hrtimer_set_expires() in hrtick_start and hrtimer_start_expires() in
__hrtick_restart() in which the former might be operating on an already
queued hrtick hrtimer, which might lead to corruption of the base.
Use hrtick_start() (which removes the timer before enqueuing it back) to
ensure hrtick hrtimer reprogramming is entirely guarded by the base
lock, so that no race conditions can occur.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210208073554.14629-2-juri.lelli@redhat.com
|
|
dl_add_task_root_domain() is called during sched domain rebuild:
rebuild_sched_domains_locked()
partition_and_rebuild_sched_domains()
rebuild_root_domains()
for all top_cpuset descendants:
update_tasks_root_domain()
for all tasks of cpuset:
dl_add_task_root_domain()
Change it so that only the task pi lock is taken to check if the task
has a SCHED_DEADLINE (DL) policy. In case that p is a DL task take the
rq lock as well to be able to safely de-reference root domain's DL
bandwidth structure.
Most of the tasks will have another policy (namely SCHED_NORMAL) and
can now bail without taking the rq lock.
One thing to note here: Even in case that there aren't any DL user
tasks, a slow frequency switching system with cpufreq gov schedutil has
a DL task (sugov) per frequency domain running which participates in DL
bandwidth management.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Quentin Perret <qperret@google.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20210119083542.19856-1-dietmar.eggemann@arm.com
|
|
commit c6bc9bd06dff ("rbtree, uprobes: Use rbtree helpers")
accidentally removed the refcount increase. Add it again.
Fixes: c6bc9bd06dff ("rbtree, uprobes: Use rbtree helpers")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210209150711.36778-1-svens@linux.ibm.com
|
|
send_call_function_single_ipi() may wake an idle CPU without sending an
IPI. The woken up CPU will process the SMP-functions in
flush_smp_call_function_from_idle(). Any raised softirq from within the
SMP-function call will not be processed.
Should the CPU have no tasks assigned, then it will go back to idle with
pending softirqs and the NOHZ will rightfully complain.
Process pending softirqs on return from flush_smp_call_function_queue().
Fixes: b2a02fc43a1f4 ("smp: Optimize send_call_function_single_ipi()")
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210123201027.3262800-2-bigeasy@linutronix.de
|
|
Use the new EXPORT_STATIC_CALL_TRAMP() / static_call_mod() to unexport
the static_call_key for the PREEMPT_DYNAMIC calls such that modules
can no longer update these calls.
Having modules change/hi-jack the preemption calls would be horrible.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When exporting static_call_key; with EXPORT_STATIC_CALL*(), the module
can use static_call_update() to change the function called. This is
not desirable in general.
Not exporting static_call_key however also disallows usage of
static_call(), since objtool needs the key to construct the
static_call_site.
Solve this by allowing objtool to create the static_call_site using
the trampoline address when it builds a module and cannot find the
static_call_key symbol. The module loader will then try and map the
trampole back to a key before it constructs the normal sites list.
Doing this requires a trampoline -> key associsation, so add another
magic section that keeps those.
Originally-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210127231837.ifddpn7rhwdaepiu@treble
|
|
Add a debugfs file to muck about with the preempt mode at runtime.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/YAsGiUYf6NyaTplX@hirez.programming.kicks-ass.net
|
|
Support the preempt= boot option and patch the static call sites
accordingly.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-9-frederic@kernel.org
|
|
Provide static call to control IRQ preemption (called in CONFIG_PREEMPT)
so that we can override its behaviour when preempt= is overriden.
Since the default behaviour is full preemption, its call is
initialized to provide IRQ preemption when preempt= isn't passed.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-8-frederic@kernel.org
|
|
Provide static calls to control preempt_schedule[_notrace]()
(called in CONFIG_PREEMPT) so that we can override their behaviour when
preempt= is overriden.
Since the default behaviour is full preemption, both their calls are
initialized to the arch provided wrapper, if any.
[fweisbec: only define static calls when PREEMPT_DYNAMIC, make it less
dependent on x86 with __preempt_schedule_func]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-7-frederic@kernel.org
|
