| Age | Commit message (Collapse) | Author |
|---|
|
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.
This patch will...
() Increase the long read time quirk timeout from 300ms to 600ms. Original
author of that quirk says 300ms was only a guess and that the number
may need to be raised in the future.
() Add this specific MMC to the quirk
Signed-off-by: Matt Gumbel <matthew.k.gumbel@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Historically for Rockchip devices we've relied on the power-on
default (or perhaps the firmware setting) to get the correct drive
phase for dw_mmc devices. This worked OK for the most part, but:
* Relying on the setting just "being right" is a bit fragile.
* As soon as there is an instance where the power on default is wrong or
where the firmware didn't configure this properly then we'll get a
mysterious failure.
In commit 7a03fe6f48f3 ("clk: rockchip: reset init state before mmc card
initialization") we actually started setting this explicitly in the
kernel, but that commit wasn't quite right and also wasn't quite
enough. See <https://patchwork.kernel.org/patch/9085311/> for some
details.
Let's explicitly set this phase in dw_mmc.
The comments inside this patch try to explain the situation quite
throughly, but the high level overview of this is:
Before this patch on rk3288 devices tested (after revert of the clock
patch described above):
* eMMC: 180 degrees
* SDMMC/SDIO0/SDIO1: 90 degrees
After this patch:
* Use 90 degree phase offset usually.
* Use 180 degree phase offset for MMC_DDR52, SDR104, HS200.
That means we are _changing_ behavior for those devices in this way:
* If we have HS200 eMMC or DDR52 eMMC, we'll run ID mode at 90
degrees (vs 180) but otherwise have no change.
* For any non-HS200 / non-DDR52 eMMC devices we'll now _always_ run at
90 degrees (vs 180). It seems fairly unlikely that building modern
hardware is using an eMMC that isn't using DDR52 or HS200, of course.
* For SDR104 cards we'll now run with 180 degree phase offset (vs 90).
It's expected that 90 degree phase offset would have worked OK, but
this gives us extra margin.
I have tested this by inserting my collection of uSD cards (mostly UHS,
though a few not) into a veyron_minnie and confirmed that they still
seem to enumerate properly. For a subset of them I tried putting a
filesystem on them and also tried running mmc_test.
Fixes: 7a03fe6f48f3 ("clk: rockchip: reset init state before mmc card initialization")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to DesignWare TRM, BLKSIZ is 16bits.
Then it's correct that max_blk_size should be 0xFFFF, not 0x10000.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add MMC_CAP_CMD23 for dw_mmc-rockchip, otherwise
failing to create rpmb partition. With it, we can
get rpmb successfully:
mmc1: new HS200 MMC card at address 0001
mmcblk0: mmc1:0001 DS2016 14.7 GiB
mmcblk0boot0: mmc1:0001 DS2016 partition 1 4.00 MiB
mmcblk0boot1: mmc1:0001 DS2016 partition 2 4.00 MiB
mmcblk0rpmb: mmc1:0001 DS2016 partition 3 4.00 MiB
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In BXT DSI there is no regs programmed with few horizontal timings
in Pixels but txbyteclkhs.. So retrieval process adds some
ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs.
Actually here for the given adjusted_mode, we are calculating the
value programmed to the port and then back to the horizontal timing
param in pixels. This is the expected value at the end of get_config,
including roundup errors. And if that is same as retrieved value
from port, then retrieved (HW state) adjusted_mode's horizontal
timings are corrected to match with SW state to nullify the errors.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-2-git-send-email-ramalingam.c@intel.com
(cherry picked from commit 042ab0c3c40be1efcaad6b526173b5536fc6c3bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf0a65d8a74a90fd57b8712d147dbca6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
SKL DPLLs shouldn't be called DPPLs.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 2edd6443e3d0 ("drm/i915: Use a table to initilize shared dplls")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462993473-8254-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit d5aab9d40135725cbe81ed5e3af5209382063193)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
With the introduction of a distinct engine->id vs the hardware id, we need
to fix up the value we use for selecting the target engine when signaling
a semaphore. Note that these values can be merged with engine->guc_id.
Fixes: de1add360522c876c25ef2bbbbab1c94bdb509ab
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461932305-14637-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 215a7e3210eb208abe634480741e418b5a8bf60c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.
This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.
v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)
Fixes: a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-2-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d4d6279abe9a4a2d52115bad122118db4995df17)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Retriving the horizontal timings from the port registers as part of
get_config().
This fixes a division by zero:
[ 56.916557] divide error: 0000 [#1] PREEMPT SMP
[ 56.921741] Modules linked in: i915(+) drm_kms_helper syscopyarea
sysfillrect sysimgblt fb_sys_fops drm intel_gtt agpgart cf
g80211 rfkill binfmt_misc ax88179_178a kvm_intel kvm irqbypass crc32c_intel
efivars tpm_tis tpm fuse
[ 56.944106] CPU: 3 PID: 1097 Comm: modprobe Not tainted 4.6.0-rc4+ #433
[ 56.951501] Hardware name: Intel Corp. Broxton M/RVP, BIOS
BXT1RVPA.X64.0131.B30.1604142217 04/14/2016
[ 56.961908] task: ffff88007a854d00 ti: ffff88007aea0000 task.ti:
ffff88007aea0000
[ 56.970273] RIP: 0010:[<ffffffffa01235b2>] [<ffffffffa01235b2>]
drm_mode_hsync+0x22/0x40 [drm]
[ 56.980043] RSP: 0018:ffff88007aea3788 EFLAGS: 00010206
[ 56.985982] RAX: 000000000788b600 RBX: ffff880073c22108 RCX:
0000000000000000
[ 56.993957] RDX: 0000000000000000 RSI: ffff88007ab06800 RDI:
ffff880073c22108
[ 57.001935] RBP: ffff88007aea3788 R08: 0000000000000001 R09:
ffff880073c221e8
[ 57.009903] R10: ffff880073c22108 R11: 0000000000000001 R12:
ffff88007a300000
[ 57.017872] R13: ffff880073c22000 R14: ffff880175f78000 R15:
ffff880175f78798
[ 57.025849] FS: 00007f105d3e6700(0000) GS:ffff88017fd80000(0000)
knlGS:0000000000000000
[ 57.034894] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 57.041317] CR2: 00007f4d485101d0 CR3: 000000007a820000 CR4:
00000000003406e0
[ 57.049292] Stack:
[ 57.051539] ffff88007aea37a0 ffffffffa043b632 ffff880175f787c8
ffff88007aea3810
[ 57.059825] ffffffffa043d59e ffff880175f787b0 ffff88007ab68c00
ffff88007aea37f0
[ 57.068128] ffff880073c221e8 ffff880073c22108 ffff880175f78780
ffff880100000000
[ 57.076430] Call Trace:
[ 57.079254] [<ffffffffa043b632>] intel_mode_from_pipe_config+0x82/0xb0
[i915]
[ 57.087405] [<ffffffffa043d59e>] intel_modeset_setup_hw_state+0x55e/0xd60
[i915]
[ 57.095847] [<ffffffffa043ff94>] intel_modeset_init+0x8e4/0x1630 [i915]
[ 57.103415] [<ffffffffa047bcf0>] i915_driver_load+0xbe0/0x1980 [i915]
[ 57.110745] [<ffffffffa0116c19>] drm_dev_register+0xa9/0xc0 [drm]
[ 57.117681] [<ffffffffa011921d>] drm_get_pci_dev+0x8d/0x1e0 [drm]
[ 57.124600] [<ffffffff8195f942>] ? _raw_spin_unlock_irqrestore+0x42/0x70
[ 57.132253] [<ffffffffa03b0384>] i915_pci_probe+0x34/0x50 [i915]
[ 57.139070] [<ffffffff8149c375>] local_pci_probe+0x45/0xa0
[ 57.145303] [<ffffffff8149d300>] ? pci_match_device+0xe0/0x110
[ 57.151924] [<ffffffff8149d6cb>] pci_device_probe+0xdb/0x130
[ 57.158355] [<ffffffff81579b93>] driver_probe_device+0x223/0x440
[ 57.165169] [<ffffffff81579e85>] __driver_attach+0xd5/0x100
[ 57.171500] [<ffffffff81579db0>] ? driver_probe_device+0x440/0x440
[ 57.178510] [<ffffffff81577736>] bus_for_each_dev+0x66/0xa0
[ 57.184841] [<ffffffff815793de>] driver_attach+0x1e/0x20
[ 57.190881] [<ffffffff81578d6e>] bus_add_driver+0x1ee/0x280
[ 57.197212] [<ffffffff8157abc0>] driver_register+0x60/0xe0
[ 57.203447] [<ffffffff8149bc50>] __pci_register_driver+0x60/0x70
[ 57.210285] [<ffffffffa0119450>] drm_pci_init+0xe0/0x110 [drm]
[ 57.216911] [<ffffffff810dcd8d>] ? trace_hardirqs_on+0xd/0x10
[ 57.223434] [<ffffffffa023a000>] ? 0xffffffffa023a000
[ 57.229237] [<ffffffffa023a092>] i915_init+0x92/0x99 [i915]
[ 57.235570] [<ffffffff810003db>] do_one_initcall+0xab/0x1d0
[ 57.241900] [<ffffffff810f9eef>] ? rcu_read_lock_sched_held+0x7f/0x90
[ 57.249205] [<ffffffff81204f18>] ? kmem_cache_alloc_trace+0x248/0x2b0
[ 57.256509] [<ffffffff811a5eee>] ? do_init_module+0x27/0x1d9
[ 57.262934] [<ffffffff811a5f26>] do_init_module+0x5f/0x1d9
[ 57.269167] [<ffffffff8112392f>] load_module+0x20ef/0x27b0
[ 57.275401] [<ffffffff8111f8e0>] ? store_uevent+0x40/0x40
[ 57.281541] [<ffffffff81124243>] SYSC_finit_module+0xc3/0xf0
[ 57.287969] [<ffffffff8112428e>] SyS_finit_module+0xe/0x10
[ 57.294203] [<ffffffff81960069>] entry_SYSCALL_64_fastpath+0x1c/0xac
[ 57.301406] Code: ff 5d c3 66 0f 1f 44 00 00 0f 1f 44 00 00 8b 87 d8 00 00
00 55 48 89 e5 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9
b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 5d c3
[ 57.322964] RIP [<ffffffffa01235b2>] drm_mode_hsync+0x22/0x40 [drm]
[ 57.330103] RSP <ffff88007aea3788>
[ 57.334276] ---[ end trace d414224cb2e2a4cf ]---
[ 57.339861] modprobe (1097) used greatest stack depth: 12048 bytes left
Fixes: 6f0e7535e7e1 ("drm/i915/BXT: Get pipe conf from the port registers")
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-1-git-send-email-ramalingam.c@intel.com
(cherry picked from commit cefc4e18785123326c5d4d985085e32160fef7f5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed3093613 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Fixes: 9b9ed3093613 (drm/i915: Remove forcewake dance from seqno/irq...)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461744121-27051-1-git-send-email-chris@chris-wilson.co.uk
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit bcbdb6d01150dcc1769ddc9baaaf7f102f27f919)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d358b ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.
The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.
I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.
Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.
v2: Reorder init_hw vs. enable_hw functions (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: ebb7c78d358b ("agp/intel-gtt: Only register fake agp driver for gen1")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462559755-353-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit ac840ae53573d9f435c88c131f6707a79aecb466)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.
v2: Deal with VBT code reorganization
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
Accept both DP and HDMI dvo_port in VBT as my BSW
at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d61992565bd3cc5b66d74ed2e96df043c2a207e2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.
v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
helper getting passed the type, we wouldn't actually have to
check at all in the driver, but the check eliminates the debug
output more honest
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b2ccb822d376d1bbbe5d1f9118d1488b25e6bc6d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e95cca48d33502a4a76b1ed09d213ce)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI
Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.
Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.
This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.
Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.
v2: Pass adaptor type to helper functions to ease driver implementation
Fix a bunch of typoes (Paulo)
Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
the type (Paulo)
Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
ease future LSPCON enabling
Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
Add kernel doc for enum drm_dp_dual_mode_type
Actually build the docs
Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit ede53344dbfd1dd43bfd73eb6af743d37c56a7c3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull motr tracing updates from Steven Rostedt:
"Three more changes.
- I forgot that I had another selftest to stress test the ftrace
instance creation. It was actually suppose to go into the 4.6
merge window, but I never committed it. I almost forgot about it
again, but noticed it was missing from your tree.
- Soumya PN sent me a clean up patch to not disable interrupts when
taking the tasklist_lock for read, as it's unnecessary because that
lock is never taken for write in irq context.
- Newer gcc's can cause the jump in the function_graph code to the
global ftrace_stub label to be a short jump instead of a long one.
As that jump is dynamically converted to jump to the trace code to
do function graph tracing, and that conversion expects a long jump
it can corrupt the ftrace_stub itself (it's directly after that
call). One way to prevent gcc from using a short jump is to
declare the ftrace_stub as a weak function, which we do here to
keep gcc from optimizing too much"
* tag 'trace-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Set ftrace_stub to weak to prevent gcc from using short jumps to it
ftrace: Don't disable irqs when taking the tasklist_lock read_lock
ftracetest: Add instance created, delete, read and enable event test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu update from Greg Ungerer:
"Only a single change to update my email address in the MAINTAINERS
file"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: change m68knommu maintainer email address
|
|
Pull sparc updates from David Miller:
"Some 32-bit kgdb cleanups from Sam Ravnborg, and a hugepage TLB flush
overhead fix on 64-bit from Nitin Gupta"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Reduce TLB flushes during hugepte changes
aeroflex/greth: fix warning about unused variable
openprom: fix warning
sparc32: drop superfluous cast in calls to __nocache_pa()
sparc32: fix build with STRICT_MM_TYPECHECKS
sparc32: use proper prototype for trapbase
sparc32: drop local prototype in kgdb_32
sparc32: drop hardcoding trap_level in kgdb_trap
|
|
The tiled 5K Dell monitor appears to be hiding it's tiled mode
inside the displayid timings block, this patch parses this
blocks and adds the modes to the modelist.
v1.1: add missing __packed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We need to use this for validating modeline additions.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This will iterate over all DisplayID blocks found in the buffer.
Previously only the first block was parsed.
https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Tomas Bzatek <tomas@bzatek.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This just makes the code easier to follow.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.
For example, the 32-bit version of "__copy_from_user_inatomic()" is
mostly the special cases for the constant size, and it's actually almost
never relevant. Most users aren't actually using a constant size
anyway, and the few cases that do small constant copies are better off
just using __get_user() instead.
So get rid of the unnecessary complexity.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.
For example, the 32-bit version of "__copy_to_user_inatomic()" is mostly
the special cases for the constant size, and it's actually never
relevant. Every user except for one aren't actually using a constant
size anyway, and the one user that uses it is better off just using
__put_user() instead.
So get rid of the unnecessary complexity.
[ The same cleanup should likely happen to __copy_from_user_inatomic()
as well, but that one has a lot more users that I need to take a look
at first ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The attached patch updates the parisc version of futex.h to match the
current generic implementation except for the spinlock code.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When enabling all-branch ftrace support (CONFIG_PROFILE_ALL_BRANCHES)
the kernel gets really huge and some ftrace assembler functions like
mcount can't reach the ftrace helper functions which are written in C.
Avoid this problem of too distant branches by moving the ftrace C-helper
functions into the .text.hot section which is put in front of the
standard .text section by the linker.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Do not hardcode MAP_HUGETLB to 0x40000, since quite some architectures
use a different value.
Tested with a parisc architecture 64bit kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add a native implementation for the sched_clock() function which utilizes the
processor-internal cycle counter (Control Register 16) as high-resolution time
source.
With this patch we now get much more fine-grained resolutions in various
in-kernel time measurements (e.g. when viewing the function tracing logs), and
probably a more accurate scheduling on SMP systems.
There are a few specific implementation details in this patch:
1. On a 32bit kernel we emulate the higher 32bits of the required 64-bit
resolution of sched_clock() by increasing a per-cpu counter at every
wrap-around of the 32bit cycle counter.
2. In a SMP system, the cycle counters of the various CPUs are not syncronized
(similiar to the TSC in a x86_64 system). To cope with this we define
HAVE_UNSTABLE_SCHED_CLOCK and let the upper layers do the adjustment work.
3. Since we need HAVE_UNSTABLE_SCHED_CLOCK, we need to provide a cmpxchg64()
function even on a 32-bit kernel.
4. A 64-bit SMP kernel which is started on a UP system will mark the
sched_clock() implementation as "stable", which means that we don't expect any
jumps in the returned counter. This is true because we then run only on one
CPU.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
By adding TRACEHOOK support we now get a clean user interface to access
registers via PTRACE_GETREGS, PTRACE_SETREGS, PTRACE_GETFPREGS and
PTRACE_SETFPREGS.
The user-visible regset struct user_regs_struct and user_fp_struct are
modelled similiar to x86 and can be accessed via PTRACE_GETREGSET.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Allow accessing 64-bit values in userspace from a 32-bit kernel.
The access is not atomic.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This patch simplifies the code for get_user() and put_user() a lot.
Instead of accessing kernel memory (%sr0) and userspace memory (%sr3)
hard-coded in the assembler instruction, we now preload %sr2 with either
%sr0 (for accessing KERNEL_DS) or with sr3 (to access USER_DS) and
use %sr2 in the load directly.
The generated code avoids a branch and speeds up execution by generating
less assembler instructions.
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
|
|
This patch adds support for the TIF_SYSCALL_TRACEPOINT on the parisc
architecture. Basically, it calls the appropriate tracepoints on syscall
entry and exit.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
just a stub pointer for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Everything should be LE when using virtio-1, but
the linux balloon driver does not seem to care about that.
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
skips ring accesses but drops out of order support
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, as Ted pointed out, fscrypto allows one more key prefix
given by filesystem to resolve backward compatibility issues. Other
than that, we've fixed several error handling cases by introducing
a fault injection facility. We've also achieved performance
improvement in some workloads as well as a bunch of bug fixes.
Summary:
Enhancements:
- fs-specific prefix for fscrypto
- fault injection facility
- expose validity bitmaps for user to be aware of fragmentation
- fallocate/rm/preallocation speed up
- use percpu counters
Bug fixes:
- some inline_dentry/inline_data bugs
- error handling for atomic/volatile/orphan inodes
- recover broken superblock"
* tag 'for-f2fs-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (73 commits)
f2fs: fix to update dirty page count correctly
f2fs: flush pending bios right away when error occurs
f2fs: avoid ENOSPC fault in the recovery process
f2fs: make exit_f2fs_fs more clear
f2fs: use percpu_counter for total_valid_inode_count
f2fs: use percpu_counter for alloc_valid_block_count
f2fs: use percpu_counter for # of dirty pages in inode
f2fs: use percpu_counter for page counters
f2fs: use bio count instead of F2FS_WRITEBACK page count
f2fs: manipulate dirty file inodes when DATA_FLUSH is set
f2fs: add fault injection to sysfs
f2fs: no need inc dirty pages under inode lock
f2fs: fix incorrect error path handling in f2fs_move_rehashed_dirents
f2fs: fix i_current_depth during inline dentry conversion
f2fs: correct return value type of f2fs_fill_super
f2fs: fix deadlock when flush inline data
f2fs: avoid f2fs_bug_on during recovery
f2fs: show # of orphan inodes
f2fs: support in batch fzero in dnode page
f2fs: support in batch multi blocks preallocation
...
|
|
|
|
The ndctl unit tests discovered that the dax enabling omitted updates to
nd_detach_and_reset(). This routine clears device the configuration
when the namespace is detached. Without this clearing userspace may
assume that the device is in the process of being configured by another
agent in the system.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Testing the dax-device autodetect support revealed a probe failure with
the following result:
dax0.1: bad offset: 0x8200000 dax disabled
The original pfn-device implementation inferred the alignment from
ilog2(offset), now that the alignment is explicit the is_power_of_2()
needs replacing with a real sanity check against the recorded alignment.
Otherwise the alignment check is useless in the implicit case and only
the minimum size of the offset matters.
This self-consistency check is further validated by the probe path that
will re-check that the offset is large enough to contain all the
metadata required to enable the device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"This has our merge window series of cleanups and fixes. These target
a wide range of issues, but do include some important fixes for
qgroups, O_DIRECT, and fsync handling. Jeff Mahoney moved around a
few definitions to make them easier for userland to consume.
Also whiteout support is included now that issues with overlayfs have
been cleared up.
I have one more fix pending for page faults during btrfs_copy_from_user,
but I wanted to get this bulk out the door first"
* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (90 commits)
btrfs: fix memory leak during RAID 5/6 device replacement
Btrfs: add semaphore to synchronize direct IO writes with fsync
Btrfs: fix race between block group relocation and nocow writes
Btrfs: fix race between fsync and direct IO writes for prealloc extents
Btrfs: fix number of transaction units for renames with whiteout
Btrfs: pin logs earlier when doing a rename exchange operation
Btrfs: unpin logs if rename exchange operation fails
Btrfs: fix inode leak on failure to setup whiteout inode in rename
btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT
Btrfs: pin log earlier when renaming
Btrfs: unpin log if rename operation fails
Btrfs: don't do unnecessary delalloc flushes when relocating
Btrfs: don't wait for unrelated IO to finish before relocation
Btrfs: fix empty symlink after creating symlink and fsync parent dir
Btrfs: fix for incorrect directory entries after fsync log replay
btrfs: build fixup for qgroup_account_snapshot
btrfs: qgroup: Fix qgroup accounting when creating snapshot
Btrfs: fix fspath error deallocation
btrfs: make find_workspace warn if there are no workspaces
btrfs: make find_workspace always succeed
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem wide cleanups:
- Use IS_ENABLED() instead of checking for built-in or module
- remove useless DRV_VERSION
- remove CLK_IS_ROOT
- remove UIE signaling
Drivers:
- ds1302: rewritten to be a proper SPI device driver
- m41t80: huge cleanup, alarm, wakelarm ans oscialltor failure
detection support
- rv3029: switch to regmap to handle rv3049, alarm support, fixes
- zynqmp: enable switching to battery power, fixes
- small fixes for at91sam9, da9053, ds1307, ds1685, ds3232, r2025,
sa1100, snvs, stmp3xxx, tps6586x"
* tag 'rtc-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (40 commits)
rtc: tps6586x: rename so module can be autoloaded
rtc: rv3029: hide unused i2c device table
rtc: rs5c372: r2025: fix check for 'oscillator halted' condition
rtc: rv3029: add alarm IRQ
rtc: rv3029: fix set_time function
rtc: rv3029: fix alarm support
rtc: rv3029: Remove some checks and warnings
rtc: rv3029: Add support of RV3049
rtc: rv3029: convert to use regmap
rtc: rv3029: remove 'i2c' in functions names
rtc: stmp3xxx: print message on error
rtc: Use IS_ENABLED() instead of checking for built-in or module
rtc: ds3232: fix call trace when rtc->ops_lock is used as NULL
rtc: snvs: return error in case enable_irq_wake fails
rtc: zynqmp: Update seconds time programming logic
rtc: sa1100: DT spelling s/interrupt-name/interrupt-names/
rtc: mc13xxx: remove UIE signaling
rtc: mxc: remove UIE signaling
rtc: ds1307: Remove CLK_IS_ROOT
rtc: hym8563: Remove CLK_IS_ROOT
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
"OMAP:
- Remove non-DT support from mailbox driver
- Move PM from client calls to native driver suspend/resume
- Trivial cleanups to make checkpatch happy
STI:
- Check return from devm_ioremap_resource as ERR_PTR, not NULL"
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Fix devm_ioremap_resource error detection code
mailbox/omap: kill omap_mbox_{save/restore}_ctx() functions
mailbox/omap: check for any unread messages during suspend
mailbox/omap: add support for suspend/resume
mailbox/omap: store mailbox interrupt type in omap_mbox_device
mailbox/omap: add blank lines after declarations
mailbox/omap: remove FSF mailing address paragraph
mailbox/omap: use variable name for sizeof() operator
mailbox/omap: drop legacy platform device support
|
