| Age | Commit message (Collapse) | Author |
|---|
|
del_page_from_lru_list() already called mem_cgroup_del_lru(). So we must
not call it again. It adds unnecessary overhead.
It was not a runtime bug because the TestClearPageCgroupAcctLRU() early in
mem_cgroup_del_lru_list() will prevent any double-deletion, etc.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use omap_serial_init_port so we can let the serial code handle the
remuxing of the RX pads. Note that this patch alone is not enough
and additional GPIO related patches are needed.
Only initialize uart3_rx_irrx pin, the other uart pins can be
stay static.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is needed to pass board specific data such as pads used to the
platform level driver init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Do this by splitting _omap_mux_init_signal as it already has most
of the necessary features.
Based on an earlier patch by Dan Murphy <dmurphy@ti.com>.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Does not allow any channel different of HCI_CHANNEL_RAW and
HCI_CHANNEL_CONTROL to bind.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.
This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch implements the read_info command which is used to fetch basic
info about an adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch implements the read_index_list command through which
userspace can get a list of current adapter indices.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch implements the initial read_version command that userspace
will use before any other management interface operations.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The command handlers for bluetooth management messaging should be able
to report errors (such as memory allocation failures) to the higher
levels in the call stack.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The atl1c driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks and they are not done correctly.
Convert atl1c to the new PCI power management framework and make it
let the PCI subsystem handle all of the PCI-specific aspects of
device handling during system power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_SUSPEND is not enabled, none of the system PM methods are
used, so do not compile them in.
Thanks to Charles Manning for reporting the problem and proposing
an initial patch.
Reported-by: Charles Manning <manningc2@actrix.gen.nz>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
|
|
Add myself and Benoît as co-maintainers of the OMAP hwmod core code.
(The OMAP hwmod code manages the integration of IP blocks on the OMAP SoC
family.)
Add Benoît as the maintainer of OMAP4-based SoC hwmod mode.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel-stable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
Convert versatile platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert omap to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert nomadik platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert iop platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert u300 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert sa1100 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert mmp to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert ixp4xx to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Provide common sched_clock() infrastructure for platforms to use to
create a 64-bit ns based sched_clock() implementation from a counter
running at a non-variable clock rate.
This implementation is based upon maintaining an epoch for the counter
and an epoch for the nanosecond time. When we desire a sched_clock()
time, we calculate the number of counter ticks since the last epoch
update, convert this to nanoseconds and add to the epoch nanoseconds.
We regularly refresh these epochs within the counter wrap interval.
We perform a similar calculation as above, and store the new epochs.
We read and write the epochs in such a way that sched_clock() can easily
(and locklessly) detect when an update is in progress, and repeat the
loading of these constants when they're known not to be stable. The
one caveat is that sched_clock() is not called in the middle of an
update. We achieve that by disabling IRQs.
Finally, if the clock rate is known at compile time, the counter to ns
conversion factors can be specified, allowing sched_clock() to be tightly
optimized. We ensure that these factors are correct by providing an
initialization function which performs a run-time check.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Russell King reports:
| On the ARM dev boards, we have a 32-bit counter running at 24MHz. Calling
| clocks_calc_mult_shift(&mult, &shift, 24MHz, NSEC_PER_SEC, 60) gives
| us a multiplier of 2796202666 and a shift of 26.
|
| Over a large counter delta, this produces an error - lets take a count
| from 362976315 to 4280663372:
|
| (4280663372-362976315) * 2796202666 / 2^26 - (4280663372-362976315) * (1000/24)
| => -38.91872422891230269990
|
| Can we do better?
|
| (4280663372-362976315) * 2796202667 / 2^26 - (4280663372-362976315) * (1000/24)
| 19.45936211449532822051
|
| which is about twice as good as the 2796202666 multiplier.
|
| Looking at the equivalent divisions obtained, 2796202666 / 2^26 gives
| 41.66666665673255920410ns per tick, whereas 2796202667 / 2^26 gives
| 41.66666667163372039794ns. The actual value wanted is 1000/24 =
| 41.66666666666666666666ns.
Fix this by ensuring we round to nearest when calculating the
multiplier.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
tegra_clocksource_read should not use cnt32_to_63, wrapping is
already handled in the clocksource code. Move the cnt32_to_63
into the sched_clock function, and replace the use of clocksource
mult and shift with a multiplication by 1000 to convert us to ns.
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Wan zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
