| Age | Commit message (Collapse) | Author |
|---|
|
Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.
Cc: Jonathan Marek <jonathan@marek.ca>
Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
We need to add a dummy smc call to the cpuidle wakeup path to force the
ROM code to save the return address after MMU is enabled again. This is
needed to prevent random hangs on secure devices like droid4.
Otherwise the system will eventually hang when entering deeper SoC idle
states with the core and mpu domains in open-switch retention (OSWR).
The hang happens as the ROM code tries to use the earlier physical return
address set by omap-headsmp.S with MMU off while waking up CPU1 again.
The hangs started happening in theory already with commit caf8c87d7ff2
("ARM: OMAP2+: Allow core oswr for omap4"), but in practise the issue went
unnoticed as various drivers were often blocking any deeper idle states
with hardware autoidle features.
This patch is based on an earlier TI Linux kernel tree commit 92f0b3028d9e
("OMAP4: PM: update ROM return address for OSWR and OFF") written by
Carlos Leija <cileija@ti.com>, Praneeth Bajjuri <praneeth@ti.com>, and
Bryan Buckley <bryan.buckley@ti.com>. A later version of the patch was
updated to use CPU_PM notifiers by Tero Kristo <t-kristo@ti.com>.
Signed-off-by: Carlos Leija <cileija@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes: caf8c87d7ff2 ("ARM: OMAP2+: Allow core oswr for omap4")
Reported-by: Carl Philipp Klemm <philipp@uvos.xyz>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: updated to apply, updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We are now registering the mpu domain three times instead of registering
mpu, core and iva domains like we should.
Fixes: d44fa156dcb2 ("ARM: OMAP2+: Configure voltage controller for cpcap")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
r is "u32" always >= 0,mipi_dsi_create_packet may return little than zero.
so r < 0 condition is never accessible.
Fixes coccicheck warnings:
./drivers/gpu/drm/omapdrm/dss/dsi.c:2155:5-6:
WARNING: Unsigned expression compared with zero: r < 0
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210312071445.1721-1-angkery@163.com
|
|
SAMPLE_OA parameter enables sampling of OA buffer and results in a call
to init the OA buffer which initializes the OA unit head/tail pointers.
The OA_EXPONENT parameter controls the periodicity of the OA reports in
the OA buffer and results in starting a hrtimer.
Before gen12, all use cases required the use of the OA buffer and i915
enforced this setting when vetting out the parameters passed. In these
platforms the hrtimer was enabled if OA_EXPONENT was passed. This worked
fine since it was implied that SAMPLE_OA is always passed.
With gen12, this changed. Users can use perf without enabling the OA
buffer as in OAR use cases. While an OAR use case should ideally not
start the hrtimer, we see that passing an OA_EXPONENT parameter will
start the hrtimer even though SAMPLE_OA is not specified. This results
in an uninitialized OA buffer, so the head/tail pointers used to track
the buffer are zero.
This itself does not fail, but if we ran a use-case that SAMPLED the OA
buffer previously, then the OA_TAIL register is still pointing to an old
value. When the timer callback runs, it ends up calculating a
wrong/large number of available reports. Since we do a spinlock_irq_save
and start processing a large number of reports, NMI watchdog fires and
causes a crash.
Start the timer only if SAMPLE_OA is specified.
v2:
- Drop SAMPLE OA check when appending samples (Ashutosh)
- Prevent read if OA buffer is not being sampled
Fixes: 00a7f0d7155c ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305210947.58751-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit be0bdd67fda9468156c733976688f6487d0c42f7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
On HSW/BDW with VT-d active the first tile row scanned out
after the first async flip of the frame often ends up corrupted.
Whether the corruption happens or not depends on the scanline
on which the async flip happens, but the behaviour seems very
consistent. Ie. the same set of scanlines (which are most scanlines)
always show the corruption. And another set of scanlines (far less
of them) never shows the corruption.
I discovered that disabling the fetch-stride stretching
feature cures the corruption. This is some kind of TLB related
prefetch thing AFAIK. We already disable it on SNB primary
planes due to a documented workaround. The hardware folks
indicated that disabling this should be fine, so let's go
with that.
And while we're here, let's document the relevant bits on all
pre-skl platforms.
Fixes: 2a636e240c77 ("drm/i915: Implement async flip for ivb/hsw")
Fixes: cda195f13abd ("drm/i915: Implement async flips for bdw")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210220103303.3448-1-ville.syrjala@linux.intel.com
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
(cherry picked from commit b7a7053ab2ec558b8ae4e55f62ea8f1f58e14f5c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
ww_acquire_init()/ww_acquire_fini()
In ww_acquire_init(), mutex_acquire() is gated by CONFIG_DEBUG_LOCK_ALLOC.
The dep_map in the ww_acquire_ctx structure is also gated by the
same config. However mutex_release() in ww_acquire_fini() is gated by
CONFIG_DEBUG_MUTEXES. It is possible to set CONFIG_DEBUG_MUTEXES without
setting CONFIG_DEBUG_LOCK_ALLOC though it is an unlikely configuration.
That may cause a compilation error as dep_map isn't defined in this
case. Fix this potential problem by enclosing mutex_release() inside
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210316153119.13802-3-longman@redhat.com
|
|
The use_ww_ctx flag is passed to mutex_optimistic_spin(), but the
function doesn't use it. The frequent use of the (use_ww_ctx && ww_ctx)
combination is repetitive.
In fact, ww_ctx should not be used at all if !use_ww_ctx. Simplify
ww_mutex code by dropping use_ww_ctx from mutex_optimistic_spin() an
clear ww_ctx if !use_ww_ctx. In this way, we can replace (use_ww_ctx &&
ww_ctx) by just (ww_ctx).
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210316153119.13802-2-longman@redhat.com
|
|
There is a possible chance that some cooling device stats buffer
allocation fails due to very high cooling device max state value.
Later cooling device update sysfs can try to access stats data
for the same cooling device. It will lead to NULL pointer
dereference issue.
Add a NULL pointer check before accessing thermal cooling device
stats data. It fixes the following bug
[ 26.812833] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 27.122960] Call trace:
[ 27.122963] do_raw_spin_lock+0x18/0xe8
[ 27.122966] _raw_spin_lock+0x24/0x30
[ 27.128157] thermal_cooling_device_stats_update+0x24/0x98
[ 27.128162] cur_state_store+0x88/0xb8
[ 27.128166] dev_attr_store+0x40/0x58
[ 27.128169] sysfs_kf_write+0x50/0x68
[ 27.133358] kernfs_fop_write+0x12c/0x1c8
[ 27.133362] __vfs_write+0x54/0x160
[ 27.152297] vfs_write+0xcc/0x188
[ 27.157132] ksys_write+0x78/0x108
[ 27.162050] ksys_write+0xf8/0x108
[ 27.166968] __arm_smccc_hvc+0x158/0x4b0
[ 27.166973] __arm_smccc_hvc+0x9c/0x4b0
[ 27.186005] el0_svc+0x8/0xc
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1607367181-24589-1-git-send-email-manafm@codeaurora.org
|
|
As per UEFI spec 2.8B section 8.2, EFI_UNSUPPORTED may be returned by
EFI variable runtime services if no variable storage is supported by
firmware. In this case, there is no point for kernel to continue
efivars initialization. That said, efivar_init() should fail by
returning an error code, so that efivarfs will not be mounted on
/sys/firmware/efi/efivars at all. Otherwise, user space like efibootmgr
will be confused by the EFIVARFS_MAGIC seen there, while EFI variable
calls cannot be made successfully.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
When KVM_REQ_MASTERCLOCK_UPDATE request is issued (e.g. after migration)
we need to make sure no vCPU sees stale values in PV clock structures and
thus all vCPUs are kicked with KVM_REQ_CLOCK_UPDATE. Hyper-V TSC page
clocksource is global and kvm_guest_time_update() only updates in on vCPU0
but this is not entirely correct: nothing blocks some other vCPU from
entering the guest before we finish the update on CPU0 and it can read
stale values from the page.
Invalidate TSC page in kvm_gen_update_masterclock() to switch all vCPUs
to using MSR based clocksource (HV_X64_MSR_TIME_REF_COUNT).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210316143736.964151-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HV_X64_MSR_TSC_EMULATION_STATUS
HV_X64_MSR_TSC_EMULATION_STATUS indicates whether TSC accesses are emulated
after migration (to accommodate for a different host TSC frequency when TSC
scaling is not supported; we don't implement this in KVM). Guest can use
the same MSR to stop TSC access emulation by writing zero. Writing anything
else is forbidden.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210316143736.964151-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There are two issues for RV32,
1) if use FLATMEM, it is useless to enable SPARSEMEM_STATIC.
2) if use SPARSMEM, both SPARSEMEM_VMEMMAP and SPARSEMEM_STATIC is enabled.
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Without this I get a missing prototype warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e178d670f251 ("riscv/kasan: add KASAN_VMALLOC support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Make sure that writes to kernel page table during KASAN vmalloc
initialization are made visible by adding a sfence.vma.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Fixes: e178d670f251 ("riscv/kasan: add KASAN_VMALLOC support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
init_resources() allocates an array of resources, based on the current
total number of memory regions and reserved memory regions. However,
allocating this array using memblock_alloc() might increase the number
of reserved memory regions. If that happens, populating the array later
based on the new number of regions will cause out-of-bounds writes
beyond the end of the allocated array.
Fix this by allocating one more entry, which may or may not be used.
Fixes: 797f0375dd2ef5cd ("RISC-V: Do not allocate memblock while iterating reserved memblocks")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
When CONFIG_SOC_CANAAN is selected, the K210 sysctl driver is always
compiled. Since this driver early init function calls the function
k210_clk_early_init() implemented by the K210 clk driver, this driver
must also always be selected for compilation ot avoid build failures.
Avoid such build failures by always selecting CONFIG_COMMON_CLK and
CONFIG_COMMON_CLK_K210 when CONFIG_SOC_CANAAN is enabled.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: c6ca7616f7d5 ("clk: Add RISC-V Canaan Kendryte K210 clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
There is a spelling mistake in a comment, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Use BUG_ON instead of a if condition followed by BUG.
Generated by: scripts/coccinelle/misc/bugon.cocci
Fixes: c22b0bcb1dd0 ("riscv: Add kprobes supported")
CC: Guo Ren <guoren@linux.alibaba.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.
Issue spotted by call_kern.cocci:
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7125 inside lock on line 7123 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6842 inside lock on line 6839 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6854 inside lock on line 6851 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7706 inside lock on line 7702 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 10260 inside lock on line 10256 but uses GFP_KERNEL
Link: https://lore.kernel.org/r/20210220093951.905362-1-christophe.jaillet@wanadoo.fr
Fixes: 324c122fc0a4 ("scsi: mpt3sas: Add module parameter multipath_on_hba")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Both add_slot_store() and remove_slot_store() try to fix up the
drc_name copied from the store buffer by placing a NUL terminator at
nbyte + 1 or in place of a '\n' if present. However, the static buffer
that we copy the drc_name data into is not zeroed and can contain
anything past the n-th byte.
This is problematic if a '\n' byte appears in that buffer after nbytes
and the string copied into the store buffer was not NUL terminated to
start with as the strchr() search for a '\n' byte will mark this
incorrectly as the end of the drc_name string resulting in a drc_name
string that contains garbage data after the n-th byte.
Additionally it will cause us to overwrite that '\n' byte on the stack
with NUL, potentially corrupting data on the stack.
The following debugging shows an example of the drmgr utility writing
"PHB 4543" to the add_slot sysfs attribute, but add_slot_store()
logging a corrupted string value.
drmgr: drmgr: -c phb -a -s PHB 4543 -d 1
add_slot_store: drc_name = PHB 4543°|<82>!, rc = -19
Fix this by using strscpy() instead of memcpy() to ensure the string
is NUL terminated when copied into the static drc_name buffer.
Further, since the string is now NUL terminated the code only needs to
change '\n' to '\0' when present.
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mpe: Reformat change log and add mention of possible stack corruption]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315214821.452959-1-tyreld@linux.ibm.com
|
|
The "lpm" and "->enabled" are all boolean. We should be using &&
rather than the bit operator.
Link: https://lore.kernel.org/r/1615896915-148864-1-git-send-email-dj0227@163.com
Fixes: 488edafb1120 ("scsi: ufs-mediatek: Introduce low-power mode for device power supply")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Yue Hu <huyue2@yulong.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Recent changes changed the completion of SCSI commands from Soft-IRQ
context to IRQ context. This triggers the following warning, when we're
completing writes to zoned block devices that go through the zone append
emulation:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc2+ #2
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
RIP: 0010:__local_bh_disable_ip+0x3f/0x50
RSP: 0018:ffff8883e1409ba8 EFLAGS: 00010006
RAX: 0000000080010001 RBX: 0000000000000001 RCX: 0000000000000013
RDX: ffff888129e4d200 RSI: 0000000000000201 RDI: ffffffff915b9dbd
RBP: ffff888113e9a540 R08: ffff888113e9a540 R09: 00000000000077f0
R10: 0000000000080000 R11: 0000000000000001 R12: ffff888129e4d200
R13: 0000000000001000 R14: 00000000000077f0 R15: ffff888129e4d218
FS: 0000000000000000(0000) GS:ffff8883e1400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f8418ebc0 CR3: 000000021202a006 CR4: 00000000001706f0
Call Trace:
<IRQ>
_raw_spin_lock_bh+0x18/0x40
sd_zbc_complete+0x43d/0x1150
sd_done+0x631/0x1040
? mark_lock+0xe4/0x2fd0
? provisioning_mode_store+0x3f0/0x3f0
scsi_finish_command+0x31b/0x5c0
_scsih_io_done+0x960/0x29e0 [mpt3sas]
? mpt3sas_scsih_scsi_lookup_get+0x1c7/0x340 [mpt3sas]
? __lock_acquire+0x166b/0x58b0
? _get_st_from_smid+0x4a/0x80 [mpt3sas]
_base_process_reply_queue+0x23f/0x26e0 [mpt3sas]
? lock_is_held_type+0x98/0x110
? find_held_lock+0x2c/0x110
? mpt3sas_base_sync_reply_irqs+0x360/0x360 [mpt3sas]
_base_interrupt+0x8d/0xd0 [mpt3sas]
? rcu_read_lock_sched_held+0x3f/0x70
__handle_irq_event_percpu+0x24d/0x600
handle_irq_event+0xef/0x240
? handle_irq_event_percpu+0x110/0x110
handle_edge_irq+0x1f6/0xb60
__common_interrupt+0x75/0x160
common_interrupt+0x7b/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
Don't use spin_lock_bh() to protect the update of the write pointer offset
cache, but use spin_lock_irqsave() for it.
Link: https://lore.kernel.org/r/3cfebe48d09db73041b7849be71ffbcec7ee40b3.1615369586.git.johannes.thumshirn@wdc.com
Fixes: 664f0dce2058 ("scsi: mpt3sas: Add support for shared host tagset for CPU hotplug")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In zonefs_open_zone(), if opened zone count is larger than
.s_max_open_zones threshold, we missed to recover .i_wr_refcnt,
fix this.
Fixes: b5c00e975779 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
The following sequence of commands:
register_ftrace_direct(ip, addr1);
modify_ftrace_direct(ip, addr1, addr2);
unregister_ftrace_direct(ip, addr2);
will cause the kernel to warn:
[ 30.179191] WARNING: CPU: 2 PID: 1961 at kernel/trace/ftrace.c:5223 unregister_ftrace_direct+0x130/0x150
[ 30.180556] CPU: 2 PID: 1961 Comm: test_progs W O 5.12.0-rc2-00378-g86bc10a0a711-dirty #3246
[ 30.182453] RIP: 0010:unregister_ftrace_direct+0x130/0x150
When modify_ftrace_direct() changes the addr from old to new it should update
the addr stored in ftrace_direct_funcs. Otherwise the final
unregister_ftrace_direct() won't find the address and will cause the splat.
Fixes: 0567d6809182 ("ftrace: Add modify_ftrace_direct()")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/bpf/20210316195815.34714-1-alexei.starovoitov@gmail.com
|
|
Change the Spidernet network driver from supported to
maintained, add the linuxppc-dev ML, and add myself as
a 'maintainer'.
Cc: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Horman says:
====================
Fixes for nfp pre_tunnel code
Louis Peens says:
The following set of patches fixes up a few bugs in the pre_tun
decap code paths which has been hiding for a while.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pre_tun_rule flows does not follow the usual add-flow path, instead
they are used to update the pre_tun table on the firmware. This means
that if the mask-id gets allocated here the firmware will never see the
"NFP_FL_META_FLAG_MANAGE_MASK" flag for the specific mask id, which
triggers the allocation on the firmware side. This leads to the firmware
mask being corrupted and causing all sorts of strange behaviour.
Fixes: f12725d98cbe ("nfp: flower: offload pre-tunnel rules")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Differentiate between ipv4 and ipv6 flows when configuring the pre_tunnel
table to prevent them trampling each other in the table.
Fixes: 783461604f7e ("nfp: flower: update flow merge code to support IPv6 tunnels")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some pre_tunnel flows combinations which are incorrectly being
offloaded without proper support, fix these.
- Matching on MPLS is not supported for pre_tun.
- Match on IPv4/IPv6 layer must be present.
- Destination MAC address must match pre_tun.dev MAC
Fixes: 120ffd84a9ec ("nfp: flower: verify pre-tunnel rules")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merely enabling compile-testing should not enable additional code.
To fix this, restrict the automatic enabling of BCM4908_ENET to
ARCH_BCM4908.
Fixes: 4feffeadbcb2e5b1 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When openvswitch conntrack offload with act_ct action. The first rule
do conntrack in the act_ct in tc subsystem. And miss the next rule in
the tc and fallback to the ovs datapath but miss set post_ct flag
which will lead the ct_state_key with -trk flag.
Fixes: 7baf2429a1a9 ("net/sched: cls_flower add CT_FLAGS_INVALID flag support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-03-16
this is a pull request of 11 patches for net/master.
The first patch is by Martin Willi and fixes the deletion of network
name spaces with physical CAN interfaces in them.
The next two patches are by me an fix the ISOTP protocol, to ensure
that unused flags in classical CAN frames are properly initialized to
zero.
Stephane Grosjean contributes a patch for the pcan_usb_fd driver,
which add MODULE_SUPPORTED_DEVICE lines for two supported devices.
Angelo Dureghello's patch for the flexcan driver fixes a potential div
by zero, if the bitrate is not set during driver probe.
Jimmy Assarsson's patch for the kvaser_pciefd disables bus load
reporting in the device, if it was previously enabled by the vendor's
out of tree drier. A patch for the kvaser_usb adds support for a new
device, by adding the appropriate USB product ID.
Tong Zhang contributes two patches for the c_can driver. First a
use-after-free in the c_can_pci driver is fixed, in the second patch
the runtime PM for the c_can_pci is fixed by moving the runtime PM
enable/disable from the core driver to the platform driver.
The last two patches are by Torin Cooper-Bennun for the m_can driver.
First a extraneous msg loss warning is removed then he fixes the
RX-path, which might be blocked by errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ena.rst documentation referred to end_start_xmit() when it should refer
to ena_start_xmit(). Fix the typo.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix multiple warnings seen with gcc 10.2.1:
reuseaddr_ports_exhausted.c:32:41: warning: missing braces around initializer [-Wmissing-braces]
32 | struct reuse_opts unreusable_opts[12] = {
| ^
33 | {0, 0, 0, 0},
| { } { }
Fixes: 7f204a7de8b0 ("selftests: net: Add SO_REUSEADDR test to check if 4-tuples are fully utilized.")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6654111c893f ("MIPS: vmlinux.lds.S: align raw appended dtb to 8
bytes") changed the alignment from STRUCT_ALIGNMENT bytes to 8 bytes.
The commit's message makes it sound like it was actually done on
purpose, but this is not the case. The commit was written when raw
appended dtb were not aligned at all. The STRUCT_ALIGN() was added a few
days before, in commit 7a05293af39f ("MIPS: boot/compressed: Copy DTB to
aligned address"). The true purpose of the commit was not to align
specifically to 8 bytes, but to make sure that the generated vmlinux'
size was properly padded to the alignment required for DTBs.
While the switch to 8-byte alignment worked for vmlinux-appended dtb
blobs, it broke vmlinuz-appended dtb blobs, as the decompress routine
moves the blob to a STRUCT_ALIGNMENT aligned address.
Fix this by changing the raw appended dtb blob alignment from 8 bytes
back to STRUCT_ALIGNMENT bytes in vmlinux.lds.S.
Fixes: 6654111c893f ("MIPS: vmlinux.lds.S: align raw appended dtb to 8 bytes")
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Save the current_thread_info()->status of X86 in the new
restart_block->arch_data field so TS_COMPAT_RESTART can be removed again.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210201174716.GA17898@redhat.com
|
|
The comment in get_nr_restart_syscall() says:
* The problem is that we can get here when ptrace pokes
* syscall-like values into regs even if we're not in a syscall
* at all.
Yes, but if not in a syscall then the
status & (TS_COMPAT|TS_I386_REGS_POKED)
check below can't really help:
- TS_COMPAT can't be set
- TS_I386_REGS_POKED is only set if regs->orig_ax was changed by
32bit debugger; and even in this case get_nr_restart_syscall()
is only correct if the tracee is 32bit too.
Suppose that a 64bit debugger plays with a 32bit tracee and
* Tracee calls sleep(2) // TS_COMPAT is set
* User interrupts the tracee by CTRL-C after 1 sec and does
"(gdb) call func()"
* gdb saves the regs by PTRACE_GETREGS
* does PTRACE_SETREGS to set %rip='func' and %orig_rax=-1
* PTRACE_CONT // TS_COMPAT is cleared
* func() hits int3.
* Debugger catches SIGTRAP.
* Restore original regs by PTRACE_SETREGS.
* PTRACE_CONT
get_nr_restart_syscall() wrongly returns __NR_restart_syscall==219, the
tracee calls ia32_sys_call_table[219] == sys_madvise.
Add the sticky TS_COMPAT_RESTART flag which survives after return to user
mode. It's going to be removed in the next step again by storing the
information in the restart block. As a further cleanup it might be possible
to remove also TS_I386_REGS_POKED with that.
Test-case:
$ cvs -d :pserver:anoncvs:anoncvs@sourceware.org:/cvs/systemtap co ptrace-tests
$ gcc -o erestartsys-trap-debuggee ptrace-tests/tests/erestartsys-trap-debuggee.c --m32
$ gcc -o erestartsys-trap-debugger ptrace-tests/tests/erestartsys-trap-debugger.c -lutil
$ ./erestartsys-trap-debugger
Unexpected: retval 1, errno 22
erestartsys-trap-debugger: ptrace-tests/tests/erestartsys-trap-debugger.c:421
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174709.GA17895@redhat.com
|
|
Move TS_COMPAT back to asm/thread_info.h, close to TS_I386_REGS_POKED.
It was moved to asm/processor.h by b9d989c7218a ("x86/asm: Move the
thread_info::status field to thread_struct"), then later 37a8f7c38339
("x86/asm: Move 'status' from thread_struct to thread_info") moved the
'status' field back but TS_COMPAT was forgotten.
Preparatory patch to fix the COMPAT case for get_nr_restart_syscall()
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174649.GA17880@redhat.com
|
|
Preparation for fixing get_nr_restart_syscall() on X86 for COMPAT.
Add a new helper which sets restart_block->fn and calls a dummy
arch_set_restart_data() helper.
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174641.GA17871@redhat.com
|
|
On a Haswell machine, the perf_fuzzer managed to trigger this message:
[117248.075892] unchecked MSR access error: WRMSR to 0x3f1 (tried to
write 0x0400000000000000) at rIP: 0xffffffff8106e4f4
(native_write_msr+0x4/0x20)
[117248.089957] Call Trace:
[117248.092685] intel_pmu_pebs_enable_all+0x31/0x40
[117248.097737] intel_pmu_enable_all+0xa/0x10
[117248.102210] __perf_event_task_sched_in+0x2df/0x2f0
[117248.107511] finish_task_switch.isra.0+0x15f/0x280
[117248.112765] schedule_tail+0xc/0x40
[117248.116562] ret_from_fork+0x8/0x30
A fake event called VLBR_EVENT may use the bit 58 of the PEBS_ENABLE, if
the precise_ip is set. The bit 58 is reserved by the HW. Accessing the
bit causes the unchecked MSR access error.
The fake event doesn't support PEBS. The case should be rejected.
Fixes: 097e4311cda9 ("perf/x86: Add constraint to create guest LBR event without hw counter")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1615555298-140216-2-git-send-email-kan.liang@linux.intel.com
|
|
A repeatable crash can be triggered by the perf_fuzzer on some Haswell
system.
https://lore.kernel.org/lkml/7170d3b-c17f-1ded-52aa-cc6d9ae999f4@maine.edu/
For some old CPUs (HSW and earlier), the PEBS status in a PEBS record
may be mistakenly set to 0. To minimize the impact of the defect, the
commit was introduced to try to avoid dropping the PEBS record for some
cases. It adds a check in the intel_pmu_drain_pebs_nhm(), and updates
the local pebs_status accordingly. However, it doesn't correct the PEBS
status in the PEBS record, which may trigger the crash, especially for
the large PEBS.
It's possible that all the PEBS records in a large PEBS have the PEBS
status 0. If so, the first get_next_pebs_record_by_bit() in the
__intel_pmu_pebs_event() returns NULL. The at = NULL. Since it's a large
PEBS, the 'count' parameter must > 1. The second
get_next_pebs_record_by_bit() will crash.
Besides the local pebs_status, correct the PEBS status in the PEBS
record as well.
Fixes: 01330d7288e0 ("perf/x86: Allow zero PEBS status with only single active event")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1615555298-140216-1-git-send-email-kan.liang@linux.intel.com
|
|
Build currently fails with -Werror=maybe-uninitialized set:
net/wireless/nl80211.c: In function '__cfg80211_wdev_from_attrs':
net/wireless/nl80211.c:124:44: error: 'wdev_id' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
Easy fix is to just initialize wdev_id to 0, since it's value doesn't
otherwise matter unless have_wdev_id is true.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
CC: Johannes Berg <johannes@sipsolutions.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jakub Kicinski <kuba@kernel.org>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20210312163651.1398207-1-jarod@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if the first channel from sband channel list is invalid
or disabled mac80211 ends up choosing it as the default channel
for monitor interfaces, making them not usable.
Fix this by assigning the first available valid or enabled
channel instead.
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
Link: https://lore.kernel.org/r/1615440547-7661-1-git-send-email-kathirve@codeaurora.org
[reword commit message, comment, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We have all the network interfaces marked as netns-local
since the only reasonable thing to do right now is to set
a whole device, including all netdevs, into a different
network namespace. For this reason, we also have our own
way of changing the network namespace.
Unfortunately, the RTNL locking changes broke this, and
it now results in many RTNL assertions. The trivial fix
for those (just hold RTNL for the changes) however leads
to deadlocks in the cfg80211 netdev notifier.
Since we only need the wiphy, and that's still protected
by the RTNL, add a new NL80211_FLAG_NO_WIPHY_MTX flag to
the nl80211 ops and use it to _not_ take the wiphy mutex
but only the RTNL. This way, the notifier does all the
work necessary during unregistration/registration of the
netdevs from the old and in the new namespace.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20210310215839.eadf7c43781b.I5fc6cf6676f800ab8008e03bbea9c3349b02d804@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
crypto_aead_encrypt returns <0 on error, so if these calls are not checked,
execution may continue with failed encrypts. It also seems that these two
crypto_aead_encrypt calls are the only instances in the codebase that are
not checked for errors.
Signed-off-by: Daniel Phan <daniel.phan36@gmail.com>
Link: https://lore.kernel.org/r/20210309204137.823268-1-daniel.phan36@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80dee ("mac80211: refactor extended element parsing")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This probably came in through some refactoring and what is
now a call to minstrel_ht_group_min_rate_offset(), remove
the unused variable.
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210219105744.f2538a80f6cf.I3d53554c158d5b896ac07ea546bceac67372ec28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Clear beacon ie pointer and ie length after free
in order to prevent double free.
==================================================================
BUG: KASAN: double-free or invalid-free \
in ieee80211_ibss_leave+0x83/0xe0 net/mac80211/ibss.c:1876
CPU: 0 PID: 8472 Comm: syz-executor100 Not tainted 5.11.0-rc6-syzkaller #0
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2c6 mm/kasan/report.c:230
kasan_report_invalid_free+0x51/0x80 mm/kasan/report.c:355
____kasan_slab_free+0xcc/0xe0 mm/kasan/common.c:341
kasan_slab_free include/linux/kasan.h:192 [inline]
__cache_free mm/slab.c:3424 [inline]
kfree+0xed/0x270 mm/slab.c:3760
ieee80211_ibss_leave+0x83/0xe0 net/mac80211/ibss.c:1876
rdev_leave_ibss net/wireless/rdev-ops.h:545 [inline]
__cfg80211_leave_ibss+0x19a/0x4c0 net/wireless/ibss.c:212
__cfg80211_leave+0x327/0x430 net/wireless/core.c:1172
cfg80211_leave net/wireless/core.c:1221 [inline]
cfg80211_netdev_notifier_call+0x9e8/0x12c0 net/wireless/core.c:1335
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:2040
call_netdevice_notifiers_extack net/core/dev.c:2052 [inline]
call_netdevice_notifiers net/core/dev.c:2066 [inline]
__dev_close_many+0xee/0x2e0 net/core/dev.c:1586
__dev_close net/core/dev.c:1624 [inline]
__dev_change_flags+0x2cb/0x730 net/core/dev.c:8476
dev_change_flags+0x8a/0x160 net/core/dev.c:8549
dev_ifsioc+0x210/0xa70 net/core/dev_ioctl.c:265
dev_ioctl+0x1b1/0xc40 net/core/dev_ioctl.c:511
sock_do_ioctl+0x148/0x2d0 net/socket.c:1060
sock_ioctl+0x477/0x6a0 net/socket.c:1177
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: syzbot+93976391bf299d425f44@syzkaller.appspotmail.com
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20210213133653.367130-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d33366 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e726c ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
