| Age | Commit message (Collapse) | Author |
|---|
|
Hariprasad Kelam says:
====================
octeontx2-af: misc RPM fixes
There are few issues with the RPM driver, such as FIFO overflow
and network performance problems due to wrong FIFO values. This
patchset adds fixes for the same.
Patch1: Fixes the mismatch between the lmac type reported by the driver
and the actual hardware configuration.
Patch2: Addresses low network performance observed even on RPMs with
larger FIFO lengths.
Patch 3 & 4: Fix the stale FEC counters reported by the driver by
accessing the correct CSRs
Patch 5: Resolves the issue related to RPM FIFO overflow during system
reboots
====================
Link: https://patch.msgid.link/20241122162035.5842-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During initialization, the AF driver resets all blocks. The RPM (MAC)
block and NIX block operate on a credit-based model. When the NIX block
resets during active traffic flow, it doesn't release credits to the RPM
block. This causes the RPM FIFO to overflow, leading to receive traffic
struck.
To address this issue, the patch introduces the following changes:
1. Stop receiving traffic at the MAC level during AF driver
initialization.
2. Perform an X2P reset (prevents RXFIFO of all LMACS from pushing data)
3. Reset the NIX block.
4. Clear the X2P reset and re-enable receiving traffic.
Fixes: 54d557815e15 ("octeontx2-af: Reset all RVU blocks")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The corrected words register(FCFECX_VL0_CCW_LO)/Uncorrected words
register (FCFECX_VL0_NCCW_LO) of FCFEC counter has different LMAC
offset which needs to be accessed differently.
Fixes: 84ad3642115d ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The earlier patch sets the 'Stats control register' for RPM
receive/transmit statistics instead of RSFEC statistics,
causing the driver to return stale FEC counters.
Fixes: 84ad3642115d ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Low network performance is observed even on RPMs with larger
FIFO lengths.
The cn10kb silicon has three RPM blocks with the following
FIFO sizes:
--------------------
| RPM0 | 256KB |
| RPM1 | 256KB |
| RPM2 | 128KB |
--------------------
The current design stores the FIFO length in a common structure for all
RPMs (mac_ops). As a result, the FIFO length of the last RPM is applied
to all RPMs, leading to reduced network performance.
This patch resolved the problem by storing the fifo length in per MAC
structure (cgx).
Fixes: b9d0fedc6234 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Due to a bug in the previous patch, there is a mismatch
between the lmac type reported by the driver and the actual
hardware configuration.
Fixes: 3ad3f8f93c81 ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
On DWMAC3 and later, there's a RX Watchdog interrupt that's used for
interrupt coalescing. It's known to be buggy on some platforms, and
dwmac-socfpga appears to be one of them. Changing the interrupt
coalescing from ethtool doesn't appear to have any effect here.
Without disabling RIWT (Received Interrupt Watchdog Timer, I
believe...), we observe latencies while receiving traffic that amount to
around ~0.4ms. This was discovered with NTP but can be easily reproduced
with a simple ping. Without this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.657 ms
With this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.254 ms
Fixes: 801d233b7302 ("net: stmmac: Add SOCFPGA glue driver")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241122141256.764578-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the clock pep->clk was not enabled in pxa168_eth_probe,
it should not be disabled in any path.
Conversely, if it was enabled in pxa168_eth_probe, it must be disabled
in all error paths to ensure proper cleanup.
Use the devm_clk_get_enabled helper function to ensure proper call balance
for pep->clk.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: a49f37eed22b ("net: add Fast Ethernet driver for PXA168.")
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Link: https://patch.msgid.link/20241121200658.2203871-1-mordan@ispras.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit b8e0ddd36ce9 ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head index, the driver uses the TX-FIFO's tail index
instead, assuming that send frames are completed.
When calculating the number of unhandled TEF events, that commit
didn't take mcp2518fd erratum DS80000789E 6. into account. According
to that erratum, the FIFOCI bits of a FIFOSTA register, here the
TX-FIFO tail index might be corrupted.
However here it seems the bit indicating that the TX-FIFO is
empty (MCP251XFD_REG_FIFOSTA_TFERFFIF) is not correct while the
TX-FIFO tail index is.
Assume that the TX-FIFO is indeed empty if:
- Chip's head and tail index are equal (len == 0).
- The TX-FIFO is less than half full.
(The TX-FIFO empty case has already been checked at the
beginning of this function.)
- No free buffers in the TX ring.
If the TX-FIFO is assumed to be empty, assume that the TEF is full and
return the number of elements in the TX-FIFO (which equals the number
of TEF elements).
If these assumptions are false, the driver might read to many objects
from the TEF. mcp251xfd_handle_tefif_one() checks the sequence numbers
and will refuse to process old events.
Reported-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Closes: https://patch.msgid.link/CAJ7t6HgaeQ3a_OtfszezU=zB-FqiZXqrnATJ3UujNoQJJf7GgA@mail.gmail.com
Fixes: b8e0ddd36ce9 ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241126-mcp251xfd-fix-length-calculation-v2-1-c2ed516ed6ba@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Dario Binacchi <dario.binacchi@amarulasolutions.com> says:
This series extends the patch 4d6d26537940 ("can: c_can: fix {rx,tx}_errors statistics"),
already merged into the mainline, to other CAN devices that similarly do
not correctly increment the error counters for reception/transmission.
Changes in v2:
- Fix patches 7 through 12 to ensure that statistics are updated even
if the allocation of skb fails.
- Add five new patches (i. e. 1-5), created during the further analysis
of the code while correcting patches from the v1 series (i. e. 7-12).
Link: https://patch.msgid.link/20241122221650.633981-1-dario.binacchi@amarulasolutions.com
[mkl: omitted patch 3]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
1, Enable ACPI_BGRT.
2, Enable MODULE COMPRESS.
3, Enable common DM targets.
4, Enable FS_ENCRYPTION and FS_VERITY.
5, Enable CPUFreq governors and drivers.
6, Enable PVPANIC MMIO and PCI drivers.
7, Enable some HID input drivers.
8, Enable some ASoC codec drivers.
9, Enable some Realtek WiFi drivers.
10, Remove some obsolete config options.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The module is supported, adding it.
Not all Loongson-2K1000 boards have an i2s interface, here is an example
of enabling it:
sound {
compatible = "loongson,ls-audio-card";
model = "Loongson-ASoC";
mclk-fs = <512>;
cpu {
sound-dai = <&i2s>;
};
codec {
sound-dai = <&es8323>;
};
};
&i2c1 {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
es8323:es8323@10 {
compatible = "everest,es8323";
reg = <0x10>;
#sound-dai-cells = <0>;
};
};
&i2s {
status = "okay";
clock-frequency = <175000000>;
#sound-dai-cells = <0>;
};
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The module is supported, adding it.
Not all Loongson-2K1000 boards have an i2s interface, here is an example
of enabling it:
sound {
compatible = "loongson,ls-audio-card";
model = "Loongson-ASoC";
mclk-fs = <512>;
cpu {
sound-dai = <&i2s>;
};
codec {
sound-dai = <&uda1342>;
};
};
&apbdma2 {
status = "okay";
};
&apbdma3 {
status = "okay";
};
&i2c3 {
status = "okay";
pinctrl-0 = <&i2c1_pins_default>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
uda1342: codec@1a {
compatible = "nxp,uda1342";
reg = <0x1a>;
#sound-dai-cells = <0>;
};
};
&i2s {
status = "okay";
pinctrl-0 = <&hda_pins_default>;
pinctrl-names = "default";
};
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch has supported PREEMPT_RT now. It uses GENERIC_ENTRY, so just
add the TIF bit (TIF_NEED_RESCHED_LAZY) related definitions and select
the Kconfig symbol (ARCH_HAS_PREEMPT_LAZY) is enough to make it go.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
It is really time.
LoongArch has all the required architecture related changes, that have
been identified over time, in order to enable PREEMPT_RT. With the recent
printk changes, the last known road block has been addressed.
Allow to enable PREEMPT_RT on LoongArch.
Below are the latency data from cyclictest on a 4-core Loongson-3A5000
machine, with a "make -j8" kernel building workload in the background.
1. PREEMPT kernel with default configuration:
./cyclictest -a -t -m -i200 -d0 -p99
policy: fifo: loadavg: 8.78 8.96 8.64 10/296 64800
T: 0 ( 4592) P:99 I:200 C:14838617 Min: 3 Act: 6 Avg: 8 Max: 844
T: 1 ( 4593) P:99 I:200 C:14838765 Min: 3 Act: 9 Avg: 8 Max: 909
T: 2 ( 4594) P:99 I:200 C:14838510 Min: 3 Act: 7 Avg: 8 Max: 832
T: 3 ( 4595) P:99 I:200 C:14838631 Min: 3 Act: 8 Avg: 8 Max: 931
2. PREEMPT_RT kernel with default configuration:
./cyclictest -a -t -m -i200 -d0 -p99
policy: fifo: loadavg: 10.38 10.47 10.35 9/336 77788
T: 0 ( 3941) P:99 I:200 C:19439626 Min: 3 Act: 12 Avg: 8 Max: 227
T: 1 ( 3942) P:99 I:200 C:19439624 Min: 2 Act: 11 Avg: 8 Max: 184
T: 2 ( 3943) P:99 I:200 C:19439623 Min: 3 Act: 4 Avg: 7 Max: 223
T: 3 ( 3944) P:99 I:200 C:19439623 Min: 2 Act: 10 Avg: 7 Max: 226
3. PREEMPT_RT kernel with tuned configuration:
./cyclictest -a -t -m -i200 -d0 -p99
policy: fifo: loadavg: 10.52 10.66 10.62 12/334 109397
T: 0 ( 4765) P:99 I:200 C:29335186 Min: 3 Act: 6 Avg: 8 Max: 62
T: 1 ( 4766) P:99 I:200 C:29335185 Min: 3 Act: 10 Avg: 8 Max: 52
T: 2 ( 4767) P:99 I:200 C:29335184 Min: 3 Act: 8 Avg: 8 Max: 64
T: 3 ( 4768) P:99 I:200 C:29335183 Min: 3 Act: 12 Avg: 8 Max: 53
Main instruments of tuned configuration include: Disable the boot rom
space in BIOS, in order to avoid kernel's speculative access to low-
speed memory (i.e. boot rom space); Disable CPUFreq scaling; Disable
RTC synchronization in the ntpd/chronyd service (also avoid other RTC
accesses when running low-latency workloads).
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Move POSIX CPU timer expiry and signal delivery into task context to
allow PREEMPT_RT setups to coexist with KVM.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Commit bab1c299f3945ffe79 ("LoongArch: Fix sleeping in atomic context in
setup_tlb_handler()") changes the gfp flag from GFP_KERNEL to GFP_ATOMIC
for alloc_pages_node(). However, for PREEMPT_RT kernels we can still get
a "sleeping in atomic context" error:
[ 0.372259] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
[ 0.372266] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
[ 0.372268] preempt_count: 1, expected: 0
[ 0.372270] RCU nest depth: 1, expected: 1
[ 0.372272] 3 locks held by swapper/1/0:
[ 0.372274] #0: 900000000c9f5e60 (&pcp->lock){+.+.}-{3:3}, at: get_page_from_freelist+0x524/0x1c60
[ 0.372294] #1: 90000000087013b8 (rcu_read_lock){....}-{1:3}, at: rt_spin_trylock+0x50/0x140
[ 0.372305] #2: 900000047fffd388 (&zone->lock){+.+.}-{3:3}, at: __rmqueue_pcplist+0x30c/0xea0
[ 0.372314] irq event stamp: 0
[ 0.372316] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[ 0.372322] hardirqs last disabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0
[ 0.372329] softirqs last enabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0
[ 0.372335] softirqs last disabled at (0): [<0000000000000000>] 0x0
[ 0.372341] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.12.0-rc7+ #1891
[ 0.372346] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022
[ 0.372349] Stack : 0000000000000089 9000000005a0db9c 90000000071519c8 9000000100388000
[ 0.372486] 900000010038b890 0000000000000000 900000010038b898 9000000007e53788
[ 0.372492] 900000000815bcc8 900000000815bcc0 900000010038b700 0000000000000001
[ 0.372498] 0000000000000001 4b031894b9d6b725 00000000055ec000 9000000100338fc0
[ 0.372503] 00000000000000c4 0000000000000001 000000000000002d 0000000000000003
[ 0.372509] 0000000000000030 0000000000000003 00000000055ec000 0000000000000003
[ 0.372515] 900000000806d000 9000000007e53788 00000000000000b0 0000000000000004
[ 0.372521] 0000000000000000 0000000000000000 900000000c9f5f10 0000000000000000
[ 0.372526] 90000000076f12d8 9000000007e53788 9000000005924778 0000000000000000
[ 0.372532] 00000000000000b0 0000000000000004 0000000000000000 0000000000070000
[ 0.372537] ...
[ 0.372540] Call Trace:
[ 0.372542] [<9000000005924778>] show_stack+0x38/0x180
[ 0.372548] [<90000000071519c4>] dump_stack_lvl+0x94/0xe4
[ 0.372555] [<900000000599b880>] __might_resched+0x1a0/0x260
[ 0.372561] [<90000000071675cc>] rt_spin_lock+0x4c/0x140
[ 0.372565] [<9000000005cbb768>] __rmqueue_pcplist+0x308/0xea0
[ 0.372570] [<9000000005cbed84>] get_page_from_freelist+0x564/0x1c60
[ 0.372575] [<9000000005cc0d98>] __alloc_pages_noprof+0x218/0x1820
[ 0.372580] [<900000000593b36c>] tlb_init+0x1ac/0x298
[ 0.372585] [<9000000005924b74>] per_cpu_trap_init+0x114/0x140
[ 0.372589] [<9000000005921964>] cpu_probe+0x4e4/0xa60
[ 0.372592] [<9000000005934874>] start_secondary+0x34/0xc0
[ 0.372599] [<900000000715615c>] smpboot_entry+0x64/0x6c
This is because in PREEMPT_RT kernels normal spinlocks are replaced by
rt spinlocks and rt_spin_lock() will cause sleeping. Fix it by disabling
NUMA optimization completely for PREEMPT_RT kernels.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Now the min_delta is 0x600 (1536) for LoongArch's constant clockevent
device. For a 100MHz hardware timer this means ~15us. This is a little
big, especially for PREEMPT_RT enabled kernels. So reduce it to 100 for
PREEMPT_RT kernel, and 1000 for others (we don't want too small values
to affect performance).
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
(1) Description of Problem:
When testing BPF JIT with the latest compiler toolchains on LoongArch,
there exist some strange failed test cases, dmesg shows something like
this:
# dmesg -t | grep FAIL | head -1
... ret -3 != -3 (0xfffffffd != 0xfffffffd)FAIL ...
(2) Steps to Reproduce:
# echo 1 > /proc/sys/net/core/bpf_jit_enable
# modprobe test_bpf
(3) Additional Info:
There are no failed test cases compiled with the lower version of GCC
such as 13.3.0, while the problems only appear with higher version of
GCC such as 14.2.0.
This is because the problems were hidden by the lower version of GCC due
to redundant sign extension instructions generated by compiler, but with
optimization of higher version of GCC, the sign extension instructions
have been removed.
(4) Root Cause Analysis:
The LoongArch architecture does not expose sub-registers, and hold all
32-bit values in a sign-extended format. While BPF, on the other hand,
exposes sub-registers, and use zero-extension (similar to arm64/x86).
This has led to some subtle bugs, where a BPF JITted program has not
sign-extended the a0 register (return value in LoongArch land), passed
the return value up the kernel, for example:
| int from_bpf(void);
|
| long foo(void)
| {
| return from_bpf();
| }
Here, a0 would be 0xffffffff instead of the expected 0xffffffffffffffff.
Internally, the LoongArch JIT uses a5 as a dedicated register for BPF
return values. That is to say, the LoongArch BPF uses a5 for BPF return
values, which are zero-extended, whereas the LoongArch ABI uses a0 which
is sign-extended.
(5) Final Solution:
Keep a5 zero-extended, but explicitly sign-extend a0 (which is used
outside BPF land). Because libbpf currently defines the return value
of an ebpf program as a 32-bit unsigned integer, just use addi.w to
extend bit 31 into bits 63 through 32 of a5 to a0. This is similar to
commit 2f1b0d3d7331 ("riscv, bpf: Sign-extend return values").
Fixes: 5dc615520c4d ("LoongArch: Add BPF JIT support")
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Whenever I try to build the kernel with upcoming GCC 15 which defaults
to -std=gnu23 I get a build failure:
CC arch/loongarch/vdso/vgetcpu.o
In file included from ./include/uapi/linux/posix_types.h:5,
from ./include/uapi/linux/types.h:14,
from ./include/linux/types.h:6,
from ./include/linux/kasan-checks.h:5,
from ./include/asm-generic/rwonce.h:26,
from ./arch/loongarch/include/generated/asm/rwonce.h:1,
from ./include/linux/compiler.h:317,
from ./include/asm-generic/bug.h:5,
from ./arch/loongarch/include/asm/bug.h:60,
from ./include/linux/bug.h:5,
from ./include/linux/mmdebug.h:5,
from ./include/linux/mm.h:6,
from ./arch/loongarch/include/asm/vdso.h:10,
from arch/loongarch/vdso/vgetcpu.c:6:
./include/linux/stddef.h:11:9: error: expected identifier before 'false'
11 | false = 0,
| ^~~~~
./include/linux/types.h:35:33: error: two or more data types in declaration specifiers
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:1: warning: useless type name in empty declaration
35 | typedef _Bool bool;
| ^~~~~~~
The kernel builds explicitly with -std=gnu11 in top Makefile, but
arch/loongarch/vdso does not use KBUILD_CFLAGS from the rest of the
kernel, just add -std=gnu11 flag to arch/loongarch/vdso/Makefile.
By the way, commit e8c07082a810 ("Kbuild: move to -std=gnu11") did a
similar change for arch/arm64/kernel/vdso32/Makefile.
Fixes: c6b99bed6b8f ("LoongArch: Add VDSO and VSYSCALL support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch's toolchain may change the default code model from normal to
medium. This is unnecessary for kernel, and generates some relocations
which cannot be handled by the module loader. So explicitly specify the
code model to normal in Makefile (for Rust 'normal' is 'small').
Cc: stable@vger.kernel.org
Tested-by: Haiyong Sun <sunhaiyong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
If an optional resource is found but fails to remap, return on failure.
Avoids any potential problems when using the iomapped resource as the
assumption is that it's available.
Fixes: 23a890d493e3 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241121193152.8966-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The f81604_handle_can_bus_errors() function only incremented the receive
error counter and never the transmit error counter, even if the ECC_DIR
flag reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 88da17436973 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-13-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ems_usb_rx_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-12-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The sun4i_can_err() function only incremented the receive error counter
and never the transmit error counter, even if the STA_ERR_DIR flag
reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
STA_ERR_DIR flag.
Fixes: 0738eff14d81 ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The sja1000_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 429da1cc841b ("can: Driver for the SJA1000 CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-10-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The hi3110_can_ist() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
The fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ifi_canfd_handle_lec_err() function was incorrectly incrementing only
the receive error counter, even in cases of bit or acknowledgment errors
that occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 5bbd655a8bd0 ("can: ifi: Add more detailed error reporting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241122221650.633981-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The m_can_handle_lec_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
allocation fails
Ensure that the statistics related to state error counters
(i. e. warning, passive, and bus-off) are updated even in case the skb
allocation fails. Additionally, also handle bus-off state is now.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The commit a22bd630cfff ("can: hi311x: do not report txerr and rxerr
during bus-off") removed the reporting of rxerr and txerr even in case
of correct operation (i. e. not bus-off).
The error count information added to the CAN frame after netif_rx() is
a potential use after free, since there is no guarantee that the skb
is in the same state. It might be freed or reused.
Fix the issue by postponing the netif_rx() call in case of txerr and
rxerr reporting.
Fixes: a22bd630cfff ("can: hi311x: do not report txerr and rxerr during bus-off")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Call the function can_change_state() if the allocation of the skb
fails, as it handles the cf parameter when it is null.
Additionally, this ensures that the statistics related to state error
counters (i. e. warning, passive, and bus-off) are updated.
Fixes: 0738eff14d81 ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Ensure that the statistics are always updated, even if the skb
allocation fails.
Fixes: 4d6d26537940 ("can: c_can: fix {rx,tx}_errors statistics")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add the missing 'name' parameter to the mount_api documentation for
fs_validate_description().
Fixes: 96cafb9ccb15 ("fs_parser: remove fs_parameter_description name field")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241125215021.231758-1-rdunlap@infradead.org
Cc: Eric Sandeen <sandeen@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Hangbin Liu says:
====================
ipv6: fix temporary address not removed correctly
Currently the temporary address is not removed when mngtmpaddr is deleted
or becomes unmanaged. The patch set fixed this issue and add a related
test.
v2:
1) delete the tempaddrs directly instead of remove them in addrconf_verify_rtnl(Sam Edwards)
2) Update the test case by checking the address including, add Sam in SOB (Sam Edwards)
====================
Link: https://patch.msgid.link/20241120095108.199779-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a test to check the temporary address could be added/removed
correctly when mngtempaddr is set or removed/unmanaged.
Signed-off-by: Sam Edwards <cfsworks@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RFC8981 section 3.4 says that existing temporary addresses must have their
lifetimes adjusted so that no temporary addresses should ever remain "valid"
or "preferred" longer than the incoming SLAAC Prefix Information. This would
strongly imply in Linux's case that if the "mngtmpaddr" address is deleted or
un-flagged as such, its corresponding temporary addresses must be cleared out
right away.
But now the temporary address is renewed even after ‘mngtmpaddr’ is removed
or becomes unmanaged as manage_tempaddrs() set temporary addresses
prefered/valid time to 0, and later in addrconf_verify_rtnl() all checkings
failed to remove the addresses. Fix this by deleting the temporary address
directly for these situations.
Fixes: 778964f2fdf0 ("ipv6/addrconf: fix timing bug in tempaddr regen")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Set the initial eee_cfg values to have 'ethtool --show-eee ' display
the initial EEE configuration.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Cc: <stable@vger.kernel.org>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241120083818.1079456-1-yong.liang.choong@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is an approach made to implement gs_usb firmware/driver based on
Zephyr RTOS. It was found that USB stack of Zephyr RTOS overwrites USB
EP addresses, if they have different last 4 bytes in absence of other
endpoints.
For example in case of gs_usb candlelight firmware EP-IN is 0x81 and
EP-OUT 0x02. If there are no additional USB endpoints, Zephyr RTOS will
overwrite EP-OUT to 0x01. More information can be found in the
discussion with Zephyr RTOS USB stack maintainer here:
https://github.com/zephyrproject-rtos/zephyr/issues/67812
There are already two different gs_usb FW driver implementations based
on Zephyr RTOS:
1. https://github.com/CANnectivity/cannectivity
(by: https://github.com/henrikbrixandersen)
2. https://github.com/zephyrproject-rtos/zephyr/compare/main...KozhinovAlexander:zephyr:gs_usb
(by: https://github.com/KozhinovAlexander)
At the moment both Zephyr RTOS implementations use dummy USB endpoint,
to overcome described USB stack behavior from Zephyr itself. Since
Zephyr RTOS is intended to be used on microcontrollers with very
constrained amount of resources (ROM, RAM) and additional endpoint
requires memory, it is more convenient to update the gs_usb driver in
the Linux kernel.
To fix this problem, update the gs_usb driver from using hard coded
endpoint numbers to evaluate the endpoint descriptors and use the
endpoints provided there.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Alexander Kozhinov <ak.alexander.kozhinov@gmail.com>
Link: https://patch.msgid.link/20241018212450.31746-1-ak.alexander.kozhinov@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In commit 6e86a1543c37 ("can: dev: provide optional GPIO based
termination support") GPIO based termination support was added.
For no particular reason that patch uses gpiod_set_value() to set the
GPIO. This leads to the following warning, if the systems uses a
sleeping GPIO, i.e. behind an I2C port expander:
| WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c
| CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c
Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the
use of sleeping GPIOs.
Cc: Nicolai Buchwitz <nb@tipi-net.de>
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Fixes: 6e86a1543c37 ("can: dev: provide optional GPIO based termination support")
Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Justin Lai says:
====================
Correcting switch hardware versions and reported speeds
This patch set mainly involves correcting switch hardware versions and
reported speeds.
Details are as follows:
1. Refactor the rtase_check_mac_version_valid() function.
2. Correct the speed for RTL907XD-V1
3. Corrects error handling of the rtase_check_mac_version_valid()
v1 -> v2:
- Add Fixes: tag.
- Add defines for hardware version id.
- Modify the error message for an invalid hardware version ID.
v2 -> v3:
- Remove the patch "Add support for RTL907XD-VA PCIe port".
v3 -> v4:
- Modify commit message to describe the main reason for the fix.
v4 -> v5
- Integrate the addition of defines for hardware version ID into the patch
"rtase: Refactor the rtase_check_mac_version_valid() function."
====================
Link: https://patch.msgid.link/20241120075624.499464-1-justinlai0215@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previously, when the hardware version ID was determined to be invalid,
only an error message was printed without any further handling. Therefore,
this patch makes the necessary corrections to address this.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previously, the reported speed was uniformly set to SPEED_5000, but the
RTL907XD-V1 actually operates at a speed of SPEED_10000. Therefore, this
patch makes the necessary correction.
Fixes: dd7f17c40fd1 ("rtase: Implement ethtool function")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Different hardware requires different configurations, but this distinction
was not made previously. Additionally, the error message was not clear
enough. Therefore, this patch will address the issues mentioned above.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Passing MSG_PEEK flag to skb_recv_datagram() increments skb refcount
(skb->users) and iucv_sock_recvmsg() does not decrement skb refcount
at exit.
This results in skb memory leak in skb_queue_purge() and WARN_ON in
iucv_sock_destruct() during socket close. To fix this decrease
skb refcount by one if MSG_PEEK is set in order to prevent memory
leak and WARN_ON.
WARNING: CPU: 2 PID: 6292 at net/iucv/af_iucv.c:286 iucv_sock_destruct+0x144/0x1a0 [af_iucv]
CPU: 2 PID: 6292 Comm: afiucv_test_msg Kdump: loaded Tainted: G W 6.10.0-rc7 #1
Hardware name: IBM 3931 A01 704 (z/VM 7.3.0)
Call Trace:
[<001587c682c4aa98>] iucv_sock_destruct+0x148/0x1a0 [af_iucv]
[<001587c682c4a9d0>] iucv_sock_destruct+0x80/0x1a0 [af_iucv]
[<001587c704117a32>] __sk_destruct+0x52/0x550
[<001587c704104a54>] __sock_release+0xa4/0x230
[<001587c704104c0c>] sock_close+0x2c/0x40
[<001587c702c5f5a8>] __fput+0x2e8/0x970
[<001587c7024148c4>] task_work_run+0x1c4/0x2c0
[<001587c7023b0716>] do_exit+0x996/0x1050
[<001587c7023b13aa>] do_group_exit+0x13a/0x360
[<001587c7023b1626>] __s390x_sys_exit_group+0x56/0x60
[<001587c7022bccca>] do_syscall+0x27a/0x380
[<001587c7049a6a0c>] __do_syscall+0x9c/0x160
[<001587c7049ce8a8>] system_call+0x70/0x98
Last Breaking-Event-Address:
[<001587c682c4a9d4>] iucv_sock_destruct+0x84/0x1a0 [af_iucv]
Fixes: eac3731bd04c ("[S390]: Add AF_IUCV socket support")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20241119152219.3712168-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In l2tp's net exit handler, we check that an IDR is empty before
destroying it:
WARN_ON_ONCE(!idr_is_empty(&pn->l2tp_tunnel_idr));
idr_destroy(&pn->l2tp_tunnel_idr);
By forcing memory allocation failures in idr_alloc_32, syzbot is able
to provoke a condition where idr_is_empty returns false despite there
being no items in the IDR. This turns out to be because the radix tree
of the IDR contains only internal radix-tree nodes and it is this that
causes idr_is_empty to return false. The internal nodes are cleaned by
idr_destroy.
Use idr_for_each to check that the IDR is empty instead of
idr_is_empty to avoid the problem.
Reported-by: syzbot+332fe1e67018625f63c9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=332fe1e67018625f63c9
Fixes: 73d33bd063c4 ("l2tp: avoid using drain_workqueue in l2tp_pre_exit_net")
Signed-off-by: James Chapman <jchapman@katalix.com>
Link: https://patch.msgid.link/20241118140411.1582555-1-jchapman@katalix.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
BIOS Enable PC beep path cause pop noise via speaker during boot time.
Set to default value from driver will solve the issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/2721bb57e20a44c3826c473e933f9105@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add speaker id check by gpio in ACPI for ASUS projects.
In other vendors, speaker id was checked by BIOS, and was applied in
last bit of subsys id, so we can load corresponding firmware binary file
for its speaker by subsys id.
But in ASUS project, the firmware binary name will be appended an extra
number to tell the speakers from different vendors. And this single digit
come from gpio level of speaker id in BIOS.
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Link: https://patch.msgid.link/20241123073718.475-1-baojun.xu@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Old procedure has a chance to meet Headphone no output.
Fixes: da911b1f5e98 ("ALSA: hda/realtek - update ALC225 depop optimize")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/5a27b016ba9d42b4a4e6dadce50a3ba4@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Speaker has no sound for Medion E15443.
Added another speaker pins for Medion E15443 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/eac4f3aca2ab45e59ccd207a90ee60e9@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
