summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-12-07media: ccs-pll: Use explicit 32-bit unsigned typeSakari Ailus
Use uint32_t instead of unsigned int for a variable that contains explicitly 32-bit numbers. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Fix check for PLL multiplier upper boundSakari Ailus
The additional multiplier (for higher VT timing) of the PLL multiplier was checked against the upper limit but the result was rounded up, possibly producing too high additional multiplier. Round down instead to keep within hardware limits. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Fix comment on check against maximum PLL multiplierSakari Ailus
The comment is about minimum PLL multiplier but the related check really deals with the maximum PLL multiplier. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Avoid overflow in pre-PLL divisor lower bound searchSakari Ailus
The external clock frequency times the PLL multiplier may exceed the value range of 32-bit unsigned integers. Instead perform the same calculation y using two divisions. The result has some potential to be different, but that's ok: this number is used to limit the range of pre-PLL divisors to find optimal values. So the effect of the rare case of a different result here would mean an invalid pre-PLL divisor is tried. That will be found out a little later in any case. Also guard against dividing by zero if the external clock frequency is higher than the maximum OP PLL output clock --- a rather improbable case. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Fix condition for pre-PLL divider lower boundSakari Ailus
The lower bound of the pre-PLL divider was calculated based on OP SYS clock frequency which is also affected by the OP SYS clock divider. This is wrong. The right clock frequency is that of the PLL output clock. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Begin calculation from OP system clock frequencySakari Ailus
The OP system clock frequency defines the CSI-2 bus clock frequency, not the PLL output clock frequency. Both values were overwritten in the end, but the wrong limit value was used for the OP system clock frequency, possibly leading to too high frequencies being used. Also remove now duplicated calculation of OP system clock frequency later in the PLL calculator. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Use the BIT macroSakari Ailus
Use the BIT macro for setting individual bits. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Document the structs in the header as well as the functionSakari Ailus
The CCS pll is used by the CCS driver at the moment, but documenting the interface makes sense. It's non-trivial and the calculator could be used elsewhere. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Move the flags field down, away from 8-bit fieldsSakari Ailus
This way the struct will use less memory, with better packing and no waste due to unsigned long. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Differentiate between CSI-2 D-PHY and C-PHYSakari Ailus
Differentiate between CSI-2 D-PHY and C-PHY. This does not yet include support for C-PHY. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Remove parallel bus supportSakari Ailus
The parallel bus PLL calculation has no users. Remove it. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: End search if there are no better values availableSakari Ailus
The VT divisor search can be ended if we've already found the value that corresponds exactly the total divisor, as there are no better (lower) values available. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Use correct VT divisor for calculating VT SYS divisorSakari Ailus
Use the correct video timing divisor to calculate the SYS divisor. Instead of the current value, the minimum was used. This could have resulted in a too low SYS divisor. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Split limits and PLL configuration into front and back partsSakari Ailus
The CCS spec supports a lot of variation in the PLL. Split the PLL in front and back parts to better prepare for supporting it. Also use CCS compliant naming for IP and OP PLL frequencies (i.e. include "clk" in the name). Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Don't use div_u64 to divide a 32-bit numberSakari Ailus
pll->pll_op_clk_freq is a 32-bit number. It does not need div_u64 to divide it. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07MAINTAINERS: add a limited ARM and ARM64 SoC entryKrzysztof Kozlowski
It is expected for ARM and ARM64 SoC related code to go through sub-architecture maintainers. Their addresses were therefore not documented to push patch traffic through sub-architecture maintainers. However when patches touch generic code, e.g. multi_v7_defconfig, the patch might not be picked up by them and instead should go to the SoC maintainers - Arnd and Olof. Add a minimal maintainer's entry for SoC covering only Makefile, so it will not appear on most of submissions (except new devicetree boards). It will though serve as a documentation and reference for cases when submitter does not know where to send his SoC-related patches. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201201211516.24921-2-krzk@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07MAINTAINERS: correct SoC Git address (formerly: arm-soc)Krzysztof Kozlowski
The SoC Git was moved from arm/arm-soc.git to soc/soc.git. Correct the ARM Sub-architectures entry. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201201211516.24921-1-krzk@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07ARM: keystone: remove SECTION_SIZE_BITS/MAX_PHYSMEM_BITSArnd Bergmann
These definitions are evidently left over from the days when sparsemem settings were platform specific. This was no longer the case when the platform got merged. There was no warning in the past, but now the asm/sparsemem.h header ends up being included indirectly, causing this warning: In file included from /git/arm-soc/arch/arm/mach-keystone/keystone.c:24: arch/arm/mach-keystone/memory.h:10:9: warning: 'SECTION_SIZE_BITS' macro redefined [-Wmacro-redefined] #define SECTION_SIZE_BITS 34 ^ arch/arm/include/asm/sparsemem.h:23:9: note: previous definition is here #define SECTION_SIZE_BITS 28 ^ Clearly the definitions never had any effect here, so remove them. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20201203231847.1484900-1-arnd@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07Merge tag 'imx-fixes-5.10-5' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.10, round 5: - Fix a regression on SoC revision detection with ANATOP, that is introduced by commit 4a4fb66119eb ("ARM: imx: Add missing of_node_put()"). - Drop PAD_GPIO_6 from imx6qdl-wandboard ENET pin group, as the pin is used by camera sensor now. - Fix I2C3_SCL pinmux on imx6qdl-kontron-samx6i board, so that SoM EEPROM can be accessed. * tag 'imx-fixes-5.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: imx6qdl-kontron-samx6i: fix I2C_PM scl pin ARM: dts: imx6qdl-wandboard-revd1: Remove PAD_GPIO_6 from enetgrp ARM: imx: Use correct SRC base address Link: https://lore.kernel.org/r/20201201091820.GW4072@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07Merge tag 'sunxi-fixes-for-5.10-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes A few more RGMII-ID fixes, and a bunch of other more random fixes * tag 'sunxi-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun7i: pcduino3-nano: enable RGMII RX/TX delay on PHY ARM: dts: sun8i: v3s: fix GIC node memory range ARM: dts: sun8i: v40: bananapi-m2-berry: Fix ethernet node ARM: dts: sun8i: r40: bananapi-m2-berry: Fix dcdc1 regulator ARM: dts: sun7i: bananapi: Enable RGMII RX/TX delay on Ethernet PHY ARM: dts: s3: pinecube: align compatible property to other S3 boards ARM: sunxi: Add machine match for the Allwinner V3 SoC arm64: dts: allwinner: h6: orangepi-one-plus: Fix ethernet Link: https://lore.kernel.org/r/1280f1de-1b6d-4cc2-8448-e5a9096a41e8.lettre@localhost Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07media: dt-bindings: schema indentation fixesRob Herring
Fix a few new indentation warnings found with yamllint (now integrated into the checks). Cc: Ricardo Ribalda <ribalda@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # For adv7604 Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: vivid: fix 'disconnect' error injectionHans Verkuil
The 'disconnect' error injection functionality suffered from bit rot. New device nodes were added without updating vivid_user_gen_s_ctrl(), so that function had to be updated for the new device nodes. Also, vivid didn't check if specific device nodes were actually ever created, so the vivid_is_last_user() would fail on that (it would return true instead of false in that case). Finally, selecting Disconnect, then unbind the vivid driver would fail since the remove() would think that the device nodes were already unregistered. Keep track of whether disconnect was pressed and re-register the device nodes in remove() before doing the real unregister. [hverkuil: unsigned uses -> unsigned int uses] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: rcar-vin: Mask VNCSI_IFMD registerJacopo Mondi
The VNCSI_IFMD register controls the data expansion mode and the channel routing between the CSI-2 receivers and VIN instances. According to the chip manual revision 2.20 not all fields are available for all the SoCs: - V3M, V3H and E3 do not support the DES1 field has they do not feature a CSI20 receiver. - D3 only supports parallel input, and the whole register shall always be written as 0. Inspect the per-SoC channel routing table where the available CSI-2 instances are reported and configure VNCSI_IFMD accordingly. This patch supports this BSP change commit: https://github.com/renesas-rcar/linux-bsp/commit/f54697394457 ("media: rcar-vin: Fix VnCSI_IFMD register access for r8a77990") [hverkuil: replace BSP commit ID with BSP URL] Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Suggested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: MAINTAINERS: Add myself as maintainer of the Amlogic GE2D driverNeil Armstrong
Add new entry to MAINTAINERS. [hverkuil: added changelog] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: meson: Add M2M driver for the Amlogic GE2D Accelerator UnitNeil Armstrong
The GE2D is a 2D accelerator with various features like configurable blitter with alpha blending, frame rotation, scaling, format conversion and colorspace conversion. The driver implements a Memory2Memory VB2 V4L2 streaming device permitting: - 0, 90, 180, 270deg rotation - horizontal/vertical flipping - source cropping - destination compositing - 32bit/24bit/16bit format conversion This adds the support for the GE2D version found in the AXG SoCs Family. The missing features are: - Source scaling - Colorspace conversion - Advanced alpha blending & blitting options Is passes v4l2-compliance: SHA: ea16a7ef13a902793a5c2626b0cefc4d956147f3, 64 bits, 64-bit time_t [hverkuil: add missing linux/bitfield.h include] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: dt-bindings: media: Add bindings for the Amlogic GE2D Accelerator UnitNeil Armstrong
The GE2D is a 2D accelerator with various features like configurable blitter with alpha blending, frame rotation, scaling, format conversion and colorspace conversion. This adds the bindings for the GE2D version found in the AXG SoCs Family. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: cedrus: Make VP8 codec as capabilityJernej Skrabec
Commit 31d9b9ef8564 ("media: cedrus: Register all codecs as capability") makes separate capability flags for each codec. However, VP8 codec was merged at the same time as mentioned patch, so there is no capability flag for it. This patch adds capability flag for VP8 and enables it for all variants except for V3s. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: gspca: Fix memory leak in probeAlan Stern
The gspca driver leaks memory when a probe fails. gspca_dev_probe2() calls v4l2_device_register(), which takes a reference to the underlying device node (in this case, a USB interface). But the failure pathway neglects to call v4l2_device_unregister(), the routine responsible for dropping this reference. Consequently the memory for the USB interface and its device never gets released. This patch adds the missing function call. Reported-and-tested-by: syzbot+44e64397bd81d5e84cba@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all planar YUV formats to common fileLaurent Pinchart
Planar pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and summarize their descriptions in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all semi-planar YUV formats to common fileLaurent Pinchart
Semi-planar pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and summarize their descriptions in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all luma-only YUV formats to common fileLaurent Pinchart
Luma-only pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and describe them in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Clarify naming scheme for 4:4:4 formatsLaurent Pinchart
Document the naming scheme for the existing packed YUV 4:4:4 formats, as previously done for the RGB formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Express 4:4:4 formats in a more compact wayLaurent Pinchart
The 4:4:4 packed YUV formats are documented with a bit-level representation, which creates a wide table. Switch to a byte-oriented representation to make it more compact. This prepares for the addition of formats with more than 8 bits per component, that would make the table way too wide. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Fill padding bits with 'X'Laurent Pinchart
The padding bits are left blank, which look weird in the XYUV format, and, worse, may lead to the VUYX format to be understand as consuming 3 bytes per pixel. Add 'X' for padding bits as we do for RGB formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all packed YUV formats to common fileLaurent Pinchart
The pixfmt-packed-yuv.rst file documents packed YUV 4:4:4 formats, but is titled generically as "Packed YUV formats". 4:2:2 and 4:1:1 packed YUV formats are documented in separate files, which can be confusing. Group all packed YUV formats in pixfmt-packed-yuv.rst, which allows documenting the 4:2:2 formats in a more concise way. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Document subsampling in more detailsLaurent Pinchart
Document YUV subsampling, including chroma spatial siting, and replace the siting examples in individual formats by references to the common documentation. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Replace '-' with 'X' to denote paddingLaurent Pinchart
Using '-' to represent padding bits and bytes make text and tables more difficult to read. Use 'x' and 'X' instead. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Make 8 bits per component table more compactLaurent Pinchart
All formats using 8 bits per component can be described with a byte granularity instead of a bit granularity without loss of precision. This makes the corresponding table more compact and easier to read. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Clarify naming scheme for RGB formatsLaurent Pinchart
The naming scheme for the RGB pixel formats has been developed organically, and isn't consistent between formats using less than 8 bits per pixels (mostly stored in 1 or 2 bytes per pixel, except for RGB666 that uses 4 bytes per pixel) and formats with 8 bits per pixel (stored in 3 or 4 bytes). For the latter category, the names use a components order convention that is the opposite of the first category, and the opposite of DRM pixel formats. This has led to lots of confusion in the past, and would really benefit from being explained more precisely. Do so, which also prepares for the addition of additional RGB pixels formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Add title for deprecated formatsLaurent Pinchart
Improve readability of the documentation by adding a section title for the deprecated formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Remove layout table for packed RGB formatsLaurent Pinchart
The packed RGB formats documentation includes a layout table without any context. This doesn't bring much useful information, and is confusing at best. Remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Move HM12 format to YUV semi-planar sectionLaurent Pinchart
V4L2_PIX_FMT_HM12 is a YUV semi-planar macro-block format. Move it from the packed YUV formats section where it was misplaced to the YUV semi-planar formats section. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Move HI240 format to vendor-specific sectionLaurent Pinchart
V4L2_PIX_FMT_HI240 is a 8-bit dithered RGB format specific to BTTV. Move it from the packed YUV formats section where it was misplaced to the vendor-specific formats section. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Remove unneeded comment about 4CC valueLaurent Pinchart
The V4L2_PIX_FMT_BGRA444 format has a comment that explains why its 4CC value is GA12. This explains the development history and isn't of much interest to readers, it should have been part of a commit message instead. Drop the comment, anyone interested in history can turn to git. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs: Fix return value from probeSakari Ailus
rval wasn't set, resulting in probe returning zero instead of an error. Fixes: de10c1619c48 ("[media] smiapp: Get clock rate if it's not available through DT") Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs: avoid printing an uninitialized variableArnd Bergmann
There is no intialization for the 'reg' variable, so printing it produces undefined behavior as well as a compile-time warning: drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized] "0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg, Remove the variable and stop printing it. Fixes: fd9065812c7b ("media: smiapp: Obtain frame descriptor from CCS limits") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: i2c: fix an uninitialized error codeArnd Bergmann
Clang points out that the error handling in ov02a10_s_stream() is broken, and just returns a random error code: drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized] if (ov02a10->streaming == on) ^~~~~~~~~~~~~~~~~~~~~~~~ drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here return ret; ^~~ drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false if (ov02a10->streaming == on) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ If streaming is already on, leave it that way and return success. Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com> Fixes: 91807efbe8ec ("media: i2c: add OV02A10 image sensor driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: Revert "media: dt-bindings: media: Use OF graph schema"Sakari Ailus
This reverts commit f61eb7bc9256aeb173d2d730f59cdd569d261c52. While aligning with the OF graph schema will be done for the media DT bindings, this patch got merged a little too hastily. Revert it for now. Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: rc: add keymap for pine64 remoteJonas Karlman
Add a keymap for the pine64 IR remote [0]. The mouse key has been mapped to KEY_EPG to provide a more useful remote. [0] http://files.pine64.org/doc/Pine%20A64%20Schematic/remote-wit-logo.jpg Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07x86/alternative: Update text_poke_bp() kernel-doc commentQiujun Huang
Update kernel-doc parameter name after c3d6324f841b ("x86/alternatives: Teach text_poke_bp() to emulate instructions") changed the last parameter from @handler to @emulate. [ bp: Make commit message more precise. ] Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20201203145020.2441-1-hqjagain@gmail.com
generated by cgit (git 2.34.1) at 2025-09-29 05:50:13 +0000